Improve fscrypt read performance by switching the decryption workqueue
from bound to unbound. With the bound workqueue, when multiple bios
completed on the same CPU, they were decrypted on that same CPU. But
with the unbound queue, they are now decrypted in parallel on any CPU.
Although fscrypt read performance can be tough to measure due to the
many sources of variation, this change is most beneficial when
decryption is slow, e.g. on CPUs without AES instructions. For example,
I timed tarring up encrypted directories on f2fs. On x86 with AES-NI
instructions disabled, the unbound workqueue improved performance by
about 25-35%, using 1 to NUM_CPUs jobs with 4 or 8 CPUs available. But
with AES-NI enabled, performance was unchanged to within ~2%.
I also did the same test on a quad-core ARM CPU using xts-speck128-neon
encryption. There performance was usually about 10% better with the
unbound workqueue, bringing it closer to the unencrypted speed.
The unbound workqueue may be worse in some cases due to worse locality,
but I think it's still the better default. dm-crypt uses an unbound
workqueue by default too, so this change makes fscrypt match.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull parisc fixlets from Helge Deller:
"Three small section mismatch fixes, one of them was found by 0-day
test infrastructure"
* 'parisc-4.17-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Move ccio_cujo20_fixup() into init section
parisc: Move setup_profiling_timer() out of init section
parisc: Move find_pa_parent_type() out of init section
The freescale.com email domain is not valid anymore, so use
the nxp.com domain instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
-----BEGIN PGP SIGNATURE-----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=bhlK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We've accumulated some fixes during the last week, some of them were
in the works for a longer time but there are some newer ones too.
Most of the fixes have a reproducer and fix user visible problems,
also candidates for stable kernels. They IMHO qualify for a late rc,
though I did not expect that many"
* tag 'for-4.17-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix crash when trying to resume balance without the resume flag
btrfs: Fix delalloc inodes invalidation during transaction abort
btrfs: Split btrfs_del_delalloc_inode into 2 functions
btrfs: fix reading stale metadata blocks after degraded raid1 mounts
btrfs: property: Set incompat flag if lzo/zstd compression is set
Btrfs: fix duplicate extents after fsync of file with prealloc extents
Btrfs: fix xattr loss after power failure
Btrfs: send, fix invalid access to commit roots due to concurrent snapshotting
Pull ARM fixes from Russell King:
- Łukasz Stelmach spotted a couple of issues with the decompressor.
- a couple of kdump fixes found while testing kdump
- replace some perl with shell code
- resolve SIGFPE breakage
- kprobes fixes
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: fix kill( ,SIGFPE) breakage
ARM: 8772/1: kprobes: Prohibit kprobes on get_user functions
ARM: 8771/1: kprobes: Prohibit kprobes on do_undefinstr
ARM: 8770/1: kprobes: Prohibit probing on optimized_callback
ARM: 8769/1: kprobes: Fix to use get_kprobe_ctlblk after irq-disabed
ARM: replace unnecessary perl with sed and the shell $(( )) operator
ARM: kexec: record parent context registers for non-crash CPUs
ARM: kexec: fix kdump register saving on panic()
ARM: 8758/1: decompressor: restore r1 and r2 just before jumping to the kernel
ARM: 8753/1: decompressor: add a missing parameter to the addruart macro
Pull x86 fixes from Thomas Gleixner:
"An unfortunately larger set of fixes, but a large portion is
selftests:
- Fix the missing clusterid initializaiton for x2apic cluster
management which caused boot failures due to IPIs being sent to the
wrong cluster
- Drop TX_COMPAT when a 64bit executable is exec()'ed from a compat
task
- Wrap access to __supported_pte_mask in __startup_64() where clang
compile fails due to a non PC relative access being generated.
- Two fixes for 5 level paging fallout in the decompressor:
- Handle GOT correctly for paging_prepare() and
cleanup_trampoline()
- Fix the page table handling in cleanup_trampoline() to avoid
page table corruption.
- Stop special casing protection key 0 as this is inconsistent with
the manpage and also inconsistent with the allocation map handling.
- Override the protection key wen moving away from PROT_EXEC to
prevent inaccessible memory.
- Fix and update the protection key selftests to address breakage and
to cover the above issue
- Add a MOV SS self test"
[ Part of the x86 fixes were in the earlier core pull due to dependencies ]
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm: Drop TS_COMPAT on 64-bit exec() syscall
x86/apic/x2apic: Initialize cluster ID properly
x86/boot/compressed/64: Fix moving page table out of trampoline memory
x86/boot/compressed/64: Set up GOT for paging_prepare() and cleanup_trampoline()
x86/pkeys: Do not special case protection key 0
x86/pkeys/selftests: Add a test for pkey 0
x86/pkeys/selftests: Save off 'prot' for allocations
x86/pkeys/selftests: Fix pointer math
x86/pkeys: Override pkey when moving away from PROT_EXEC
x86/pkeys/selftests: Fix pkey exhaustion test off-by-one
x86/pkeys/selftests: Add PROT_EXEC test
x86/pkeys/selftests: Factor out "instruction page"
x86/pkeys/selftests: Allow faults on unknown keys
x86/pkeys/selftests: Avoid printf-in-signal deadlocks
x86/pkeys/selftests: Remove dead debugging code, fix dprint_in_signal
x86/pkeys/selftests: Stop using assert()
x86/pkeys/selftests: Give better unexpected fault error messages
x86/selftests: Add mov_to_ss test
x86/mpx/selftests: Adjust the self-test to fresh distros that export the MPX ABI
x86/pkeys/selftests: Adjust the self-test to fresh distros that export the pkeys ABI
...
Pull UP timer fix from Thomas Gleixner:
"Work around the for_each_cpu() oddity on UP kernels in the tick
broadcast code which causes boot failures because the CPU0 bit is
always reported as set independent of the cpumask content"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Use for_each_cpu() specially on UP kernels
Pull scheduler fixlets from Thomas Gleixner:
"Three trivial fixlets for the scheduler:
- move print_rt_rq() and print_dl_rq() declarations to the right
place
- make grub_reclaim() static
- fix the bogus documentation reference in Kconfig"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix documentation file path
sched/deadline: Make the grub_reclaim() function static
sched/debug: Move the print_rt_rq() and print_dl_rq() declarations to kernel/sched/sched.h
Pull RAS fix from Thomas Gleixner:
"Fix a regression in the new AMD SMCA code which issues an SMP function
call from the early interrupt disabled region of CPU hotplug. To avoid
that, use cached block addresses which can be used directly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE/AMD: Cache SMCA MISC block addresses
Pull perf tooling fixes from Thomas Gleixner:
- fix segfault when processing unknown threads in cs-etm
- fix "perf test inet_pton" on s390 failing due to missing inline
- display all available events on 'perf annotate --stdio'
- add missing newline when parsing an empty BPF program
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Add missing newline when parsing empty BPF proggie
perf cs-etm: Remove redundant space
perf cs-etm: Support unknown_thread in cs_etm_auxtrace
perf annotate: Display all available events on --stdio
perf test: "probe libc's inet_pton" fails on s390 due to missing inline
Pull locking fixes from Thomas Gleixner:
"Two fixes to address shortcomings of the rwsem/percpu-rwsem lock
debugging code which emits false positive warnings when the rwsem is
anonymously locked and unlocked"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/percpu-rwsem: Annotate rwsem ownership transfer by setting RWSEM_OWNER_UNKNOWN
locking/rwsem: Add a new RWSEM_ANONYMOUSLY_OWNED flag
Pull EFI fixes from Thomas Gleixner:
- Use explicitely sized type for the romimage pointer in the 32bit EFI
protocol struct so a 64bit kernel does not expand it to 64bit. Ditto
for the 64bit struct to avoid the reverse issue on 32bit kernels.
- Handle randomized tex offset correctly in the ARM64 EFI stub to avoid
unaligned data resulting in stack corruption and other hard to
diagnose wreckage.
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm64: Handle randomized TEXT_OFFSET
efi: Avoid potential crashes, fix the 'struct efi_pci_io_protocol_32' definition for mixed mode
Pull core fixes from Thomas Gleixner:
- Unbreak the BPF compilation which got broken by the unconditional
requirement of asm-goto, which is not supported by clang.
- Prevent probing on exception masking instructions in uprobes and
kprobes to avoid the issues of the delayed exceptions instead of
having an ugly workaround.
- Prevent a double free_page() in the error path of do_kexec_load()
- A set of objtool updates addressing various issues mostly related to
switch tables and the noreturn detection for recursive sibling calls
- Header sync for tools.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Detect RIP-relative switch table references, part 2
objtool: Detect RIP-relative switch table references
objtool: Support GCC 8 switch tables
objtool: Support GCC 8's cold subfunctions
objtool: Fix "noreturn" detection for recursive sibling calls
objtool, kprobes/x86: Sync the latest <asm/insn.h> header with tools/objtool/arch/x86/include/asm/insn.h
x86/cpufeature: Guard asm_volatile_goto usage for BPF compilation
uprobes/x86: Prohibit probing on MOV SS instruction
kprobes/x86: Prohibit probing on exception masking instructions
x86/kexec: Avoid double free_page() upon do_kexec_load() failure
Support XS-PHY for MediaTek SoCs with USB3.1 GEN2 controller
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a DT binding documentation of XS-PHY for MediaTek SoCs
with USB3.1 GEN2 controller
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There are two QUSB2 PHYs present on sdm845. In order
to improve eye diagram for both the PHYs some parameters
need to be changed. Provide device tree properties to
override these from board specific device tree files.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To improve eye diagram for PHYs on different boards of same SOC,
some parameters may need to be changed. Provide device tree
properties to override these from board specific device tree
files. While at it, replace "qcom,qusb2-v2-phy" with compatible
string for USB2 PHY on sdm845 which was earlier added for
sdm845 only.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
QMP V3 UNI PHY is a single lane USB3 PHY without support
for DisplayPort (DP).
Main difference from DP combo QMPv3 PHY is that UNI PHY
doesn't have dual RX/TX lanes and no separate DP_COM
block for configuration related to type-c or DP.
Also remove "qcom,qmp-v3-usb3-phy" compatible string which
was earlier added for sdm845 only as there wouldn't be
any user of same.
While at it, fix has_pwrdn_delay attribute for USB-DP
PHY configuration and.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update compatible strings for USB3 PHYs on SDM845.
One is QMPv3 DisplayPort-USB combo PHY and other one
is USB UNI PHY which is single lane USB3 PHY without
DP capability. While at it also remove "qcom,qmp-v3-usb3-phy"
compatible string which was earlier added for sdm845
only as there wouldn't be any user of same.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.
Fixes: ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@vger.kernel.org> # 4.14+
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
QMP PHY for USB/PCIE requires pipe_clk for locking of
retime buffers at the pipe interface. Driver checks for
PHY_STATUS without enabling pipe_clk due to which
phy_init() fails with initialization timeout.
Though pipe_clk is output from PHY (after PLL is programmed
during initialization sequence) to GCC clock_ctl and then fed
back to PHY but for PHY_STATUS register to reflect successful
initialization pipe_clk from GCC must be present.
Since, clock driver now ignores status_check for pipe_clk on
clk_enable/disable, driver can safely enable/disable pipe_clk
from phy_init/exit.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes the following issues:
* warning reported by checkpatch:
WARNING: line over 80 characters
#87: FILE: drivers/phy/st/phy-stm32-usbphyc.c:87:
+static void stm32_usbphyc_get_pll_params(u32 clk_rate, struct pll_params *pll_params)
* bug reported by static checker (Dan Carpenter):
drivers/phy/st/phy-stm32-usbphyc.c:371 stm32_usbphyc_probe()
error: uninitialized symbol 'i'.
* unused stm32_usbphyc structure member: bool pll_enabled.
* unnecessary extra line in stm32_usbphyc_of_xlate
Fixes: 94c358da3a "phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)"
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We can suspend the mdm6600 over USB via sysfs and then mdm6600 enters
a low-power idle mode. In the low-power mode, mdm6600 radio and n_gsm
uart are functional but we need to use USB mode0 GPIO pin to send a
wake-up pulse to the modem to talk with it over n_gsm.
As the GPIO mode0 line is dual purposed and and also needed by the
USB PHY driver to boot mdm6600 into the correct USB mode, let's also
manage the wake-up GPIO in the USB PHY driver. For the USB PHY idle,
there does not anything specific we need to do for runtime PM after
getting the PHY configured. The PHY framework already idles the USB
PHY when not in use separately from the mdm6600 state.
It seems that it takes about 100 - 200ms for mdm6600 to wake up from
the low-power idle mode. And then mdm6600 stays awake about 1.2s until
it needs to be kicked again. The mdm6600 status GPIO pins don't seem
to change state when mdm6600 changes between normal and idle mode.
Let's manage the mdm6600 mode with runtime PM. If phy-mapphone-mdm6600
sysfs entry for power/control is set to "on", we keep mdm6600 out of
idle by kicking the GPIO line. If the entry is set to "auto" we let
mdm6600 enter low-power state.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The new helper returns index of the matching string in an array.
We are going to use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sometimes it's useful to stream samples forever, such as when
stress-testing a driver overnight to check for memory leaks or other
issues. When the program receives a signal, it will gracefully cleanup,
so it is still safe to terminate at any time.
Add support for specifying a negative -c option, meaning that we should
loop forever. To do so, we need to use a long long (instead of just
long) for num_loops so that current code specifying num_loops greater
than UNSIGNED_LONG_MAX doesn't break.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Several types are mismatched and causing implicit conversions. Fix them
up so the types match.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
To avoid regressions, this patch changes the DTS files for the only two
users of this driver that didn't have this property yet.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On RDU1, sdhc1 is used for eMMC, and that is 3.3V only.
Thus configure device node not to probe it as SD/SDIO and not try 1.8V.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vybrid has single internal temperature sensor connected to both internal
ADC modules.
vf610-zii-dev already has ADC0 enabled. Now, to get temperature sensor
captured by iio_hwmon driver, need to configure iio_hwmon node to use
that ADC.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Corrected coding style issue:
"ERROR: space required before the open parenthesis '('"
Signed-off-by: John Whitmore <johnfwhitmore@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corrected coding style issue: "ERROR: space prohibited before that ','"
Signed-off-by: John Whitmore <johnfwhitmore@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses "operating-points-v2" instead of
"operating-points" to be more fit with cpufreq-dt
driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cpu_to_*() functions already have a cast to u* built in,
so the cast is never required. Review and remove all of
them along the code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in N_MSG message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX7S does NOT support CPU frequency scaling, so no
need to specify the CPU regulator supply.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct CPU supply name to meet cpufreq-dt driver's
requirement for voltage scaling.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On RDU1, imx51 usbh1 interface is either not used, or used via external
block that breaks USB2 signalling.
To keep things working if high-speed device gets connected to that
block, use ChipIdea feature to limit port to full speed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix 2 "Alignment should match open parenthesis" messages issued by
checkpatch.
Signed-off-by: Tim Collier <osdevtc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two issues with parameters not aligned to opening parenthesis, as
reported by checkpatch. File is now clean for checkpatch.
Signed-off-by: Tim Collier <osdevtc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was inherited from qemu1 and not used anymore.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unit-address and reg property from anatop regulators to fix
the following DTC warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I announced the intent to drop some of these meter drivers
on the IIO list last cycle. This device is obsolete and not easily
obtained. No one has come forward with suitable test hardware and
the driver would need a lot of work to move out of staging.
As such I am dropping it. We can always bring it back again
if a user / tester emerges in the future.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I announced the intent to drop some of these meter drivers
on the IIO list last cycle. This device is obsolete and not easily
obtained. No one has come forward with suitable test hardware and
the driver would need a lot of work to move out of staging.
As such I am dropping it. We can always bring it back again
if a user / tester emerges in the future.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I announced the intent to drop some of these meter drivers
on the IIO list last cycle. This device is obsolete and not easily
obtained. No one has come forward with suitable test hardware and
the driver would need a lot of work to move out of staging.
As such I am dropping it. We can always bring it back again
if a user / tester emerges in the future.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I announced the intent to drop some of these meter drivers
on the IIO list last cycle. This device is obsolete and not easily
obtained. No one has come forward with suitable test hardware and
the driver would need a lot of work to move out of staging.
As such I am dropping it. We can always bring it back again
if a user / tester emerges in the future.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the iio driver for the ad2s1200 and ad2s1205 resolver-to-digital
converter out of staging, into mainline iio subsystems.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add David Veenstra as a copyright holders and as an author,
for all of the staging clean ups of the ad2s1200 driver.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A scaling factor of approximately 2 * Pi / (2^12 -1) is added,
to scale the 12-bits angular position to radians.
A return type of IIO_VAL_INT_PLUS_NANO is used, so that the scale of
both the angle channel and angular velocity channel has 7 significant
digits.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sysfs iio ABI states radians per second is expected as the unit for
angular velocity, but the 12-bit angular velocity register has
revolution per seconds as its unit. So a scaling factor of approximately
2 * Pi is added to the angular velocity channel.
Signed-off-by: David Veenstra <davidjulianveenstra@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>