The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up CRC offload set ip_summed to CHECKSUM_PARTIAL
instead of CHECKSUM_UNNECESSARY. This is consistent with the
definition of CHECKSUM_PARTIAL.
The only driver that seems to be advertising NETIF_F_FCOE_CRC is
ixgbe. AFICT the driver does not look at ip_summed for FCOE and
just assumes that CRC is being offloaded.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same thing as skb_transport_offset but returns the offset of the inner
transport header (when skb->encpasulation is set).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce __remove_dirty_inode to clean up codes in remove_dirty_dir_inode.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Add a new dirt list node member in inode info for linking the inode to
global dirty list in superblock, instead of old implementation which
allocate slab cache memory as an entry to inode.
It avoids memory pressure due to slab cache allocation, and also makes
codes more clean.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
remove_dirty_dir_inode will be renamed to remove_dirty_inode as a generic
function in following patch for removing directory/regular/symlink inode
in global dirty list.
Here rename ino management related functions for readability, also in
order to avoid name conflict.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
commit db0fa0cb01 "scatterlist: use sg_phys()" did replacements of
the form:
phys_addr_t phys = page_to_phys(sg_page(s));
phys_addr_t phys = sg_phys(s) & PAGE_MASK;
However, this breaks platforms where sizeof(phys_addr_t) >
sizeof(unsigned long). Revert for 4.3 and 4.4 to make room for a
combined helper in 4.5.
Cc: <stable@vger.kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: db0fa0cb01 ("scatterlist: use sg_phys()")
Suggested-by: Joerg Roedel <joro@8bytes.org>
Reported-by: Vitaly Lavrov <vel21ripn@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
msg_iocb needs to be initialized on the recv/recvfrom path.
Otherwise afalg will wrongly interpret it as an async call.
Cc: stable@vger.kernel.org
Reported-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems gcc can automatically inline apbt_writel() for us, but
apbt_real isn't inlined. This patch makes them inline to get a trivial
performance improvement: 4096 rounds of __apbt_read_clocksource() call
spend time on Marvell BG4CT platform:
before the patch 1275240ns on average
after the patch 1263240ns on average
so we get 1% performance improvement.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It's safe to use the relaxed version. From another side, the relaxed io
accessor macros are available on all architectures now, so we can use
the relaxed versions to get a trivial system performance improvement,
we measured time the following functions spent on Marvell BG4CT:
4096 rounds of __apbt_read_clocksource() call:
before the patch: 1263240ns on average
after the patch: 1250080ns on average
improved by 1%
4096 rounds of apbt_eoi() call:
before the patch: 1290960ns on average
after the patch: 1248240ns on average
4096 rounds of apbt_next_event() call:
before the patch: 3333660ns on average
after the patch: 1322040ns on average
improved by 60%!
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
On Marvell BG4CT platform, we observed the __apbt_read_clocksource()
return wrong value: Let's assume the APBTMR_N_CURRENT_VALUE value is
0xf0000000, we got 0xffffffff0fffffff, but it should be 0xfffffff.
This issue should be common on all 64bit platforms. We fix the issue
by letting aptb_readl() return u32. apbt_writel() is also updated
to write u32 val rather than unsigned long.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Previously the "vendor" and "product" IDs for the elan_i2c driver simply
reported 0000. This patch modifies the elan_i2c driver to include the
Elan vendor ID and the touchpad's product id under
input/input*/{vendor,product}.
Specifically, this is to allow us to apply a generic Elan gestures config
that will apply to all Elan touchpads on ChromeOS. These configs match to
input devices in various ways, but one major way is by matching on vendor
ID. Adding this patch allows the default Elan touchpad config to be
applied to Elan touchpads in this kernel by matching on devices that have
vendor ID 04f3.
Note that product ID is also available via custom sysfs entry "product_id"
as well.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This has fixes spread thru driver, notably among them
- edma fixes for recent edma DT changes which went into 4.4
- odd fixes for at_hdmac
- minor fixes on bc dma and mic dma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r53B
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.4-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This has fixes spread thru driver, notably among them:
- edma fixes for recent edma DT changes which went into 4.4
- odd fixes for at_hdmac
- minor fixes on bc dma and mic dma"
* tag 'dmaengine-fix-4.4-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_xdmac: fix at_xdmac_prep_dma_memcpy()
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
dmaengine: mic_x100: add missing spin_unlock
dmaengine: bcm2835-dma: Convert to use DMA pool
dmaengine: at_xdmac: fix bad behavior in interleaved mode
dmaengine: at_xdmac: fix false condition for memset_sg transfers
dmaengine: at_xdmac: fix macro typo
* OMAP: fix analog tv-out when using omapdrm
* fsl: Fix kernel crash when diu_ops is not implemented
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q7XP
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull two fbdev fixes from Tomi Valkeinen:
- OMAP: fix analog tv-out when using omapdrm
- fsl: Fix kernel crash when diu_ops is not implemented
* tag 'fbdev-fixes-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix timings for VENC to match what omapdrm expects
video: fbdev: fsl: Fix kernel crash when diu_ops is not implemented
Stas Nichiporovich reported a regression in his HFSC qdisc setup
on a non multi queue device.
It turns out I mistakenly added a TCQ_F_NOPARENT flag on all qdisc
allocated in qdisc_create() for non multi queue devices, which was
rather buggy. I was clearly mislead by the TCQ_F_ONETXQUEUE that is
also set here for no good reason, since it only matters for the root
qdisc.
Fixes: 4eaf3b84f2 ("net_sched: fix qdisc_tree_decrease_qlen() races")
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Tested-by: Stas Nichiporovich <stasn77@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Bolle says:
====================
ser_gigaset: fix deallocation of platform device structure
Sascha Levin reported that the syzkaller fuzzer triggered a WARNING in
ser_gigaset (see https://lkml.kernel.org/g/56587467.8050102@oracle.com ). It
turned out that ser_gigaset has always deallocated its platform device
structure incorrectly. Tilman submitted the patch that fixes that (3/4) and a
related cleanup (4/4).
Tilman also submitted a minor cleanup of some NULL checks (1/4) that prompted
Alan to turn those checks into WARN_ONs (2/4). If no one hits these WARN_ONs in
the next couple of releases these WARN_ONs should be removed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
device->platform_data and platform_device->resource are never used
and remain NULL through their entire life. Drops the kfree() calls
for them from the device release method.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When shutting down the device, the struct ser_cardstate must not be
kfree()d immediately after the call to platform_device_unregister()
since the embedded struct platform_device is still in use.
Move the kfree() call to the release method instead.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Fixes: 2869b23e4b ("drivers/isdn/gigaset: new M101 driver (v2)")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks do nothing useful to protect the code from races. On the
other hand if the old code has been masking a real bug we would like to
know about it.
The check for tiocmset is kept because it is valid for a tty driver to
have a NULL tiocmset method. That in itself is probably a mistake given
modern coding practices - but needs fixing in the tty layer.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34d7a5b70 ("tty: The big operations rework") changed
tty->driver to tty->ops but left NULL checks for tty->driver untouched.
Fix.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
[pebolle: removed Fixes tag]
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fix from Herbert Xu:
"This fixes a boundary condition in the blkcipher SG walking code that
can lead to a crash when used with the new chacha20 algorithm"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Copy iv from desc even for 0-len walks
Pavel Machek reports a warning about W+X pages found in the "Persisent"
kmap area. After grepping for it (using the correct spelling), and not
finding it, I noticed how the debug printk was just misspelled. Fix it.
The actual mapping bug that Pavel reported is still open. It's
apparently a separate issue from the known EFI page tables, looks like
it's related to the HIGHMEM mappings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem here is that at the end of the loop we test for if
idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a
post-op, it actually ends up set to (u8)-1. I have fixed this by
moving the decrement inside the loop.
Fixes: 486a5bc77a ('qlcnic: Add support for 83xx suspend and resume.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ret as the return value from the rsnd_mix_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_dvc_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_ctu_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We test for if "tries" is zero at the end but "tries--" is a post-op so
it will end with "tries" set to -1. I have changed it to a pre-op
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that after the loop we test for "if (!i) " but
because "i--" is a post-op we exit with i set to -1. I have fixed this
by changing it to a pre-op instead. I had to change the starting value
from 3 to 4 so that we still iterate 3 times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of the fixed PHY.
This patch is based on commit 87009814cd ("ucc_geth: use the new fixed
PHY helpers").
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the loop we test "if (!count)" but because "count--" is
a post-op then the loop will end with count set to -1. I have fixed
this by changing it to --count.
Fixes: c5aa9e3b81 ('amd-xgbe: Initial AMD 10GbE platform driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two issue here.
1) cnt starts as maxloop + 1 so all these loops iterate one more time
than intended.
2) At the end of the loop we test for "if (maxloop && !cnt)" but for
the first two loops, we end with cnt equal to -1. Changing this to
a pre-op means we end with cnt set to 0.
Fixes: cae86d4a4e ('mISDN: Add driver for Infineon ISDN chipset family')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge "Broadcom soc changes for v4.5" from Florian Fainelli:
This pull request contains Broadcom SoC changes for 4.5, with the following changes:
- Lucas Stach removes the workaround for an imprecise fault for Broadcom
BCM5301x SoCs (Northstar) since this is now handled by the ARM/Linux kernel
directly
- Hauke Merthens enables a bunch of erratas for the Cortex-A9 and PL310 L2
cache present on early Northstar chips (BCM4708)
- Kapil Hali adds SMP support for the Northstar Plus SoCs by consolidating the
existing SMP code for Kona SoCs (mobile platforms), fixng the Device Tree
binding for the Kona platforms (wrong placement for 'enable-method' and
'secondary-reg') and then finally adds the functional code for the Northstar
Plus platforms to boot their secondary CPUs
- Jon Mason enables SMP on BCM4708/BCM5301X (Northstar SoCs) by building the generic
Northstar/Northstar Plus SMP code, and adding the relevant SMP Device Tree nodes
* tag 'arm-soc/for-4.5/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
ARM: BCM5310X: activate erratas needed for SoC
ARM: BCM5301X: remove workaround imprecise abort fault handler
prepare_pages() may end up calling prepare_uptodate_page() twice if our
write only spans a single page. But if the first call returns an error,
our page will be unlocked and its not safe to call it again.
This bug goes all the way back to 2011, and it's not something commonly
hit.
While we're here, add a more explicit check for the page being truncated
away. The bare lock_page() alone is protected only by good thoughts and
i_mutex, which we're sure to regret eventually.
Reported-by: Dave Jones <dsj@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Dave Jones found a warning from kasan in setup_cluster_bitmaps()
==================================================================
BUG: KASAN: stack-out-of-bounds in setup_cluster_bitmap+0xc4/0x5a0 at
addr ffff88039bef6828
Read of size 8 by task nfsd/1009
page:ffffea000e6fbd80 count:0 mapcount:0 mapping: (null)
index:0x0
flags: 0x8000000000000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 1009 Comm: nfsd Tainted: G W
4.4.0-rc3-backup-debug+ #1
ffff880065647b50 000000006bb712c2 ffff88039bef6640 ffffffffa680a43e
0000004559c00000 ffff88039bef66c8 ffffffffa62638d1 ffffffffa61121c0
ffff8803a5769de8 0000000000000296 ffff8803a5769df0 0000000000046280
Call Trace:
[<ffffffffa680a43e>] dump_stack+0x4b/0x6d
[<ffffffffa62638d1>] kasan_report_error+0x501/0x520
[<ffffffffa61121c0>] ? debug_show_all_locks+0x1e0/0x1e0
[<ffffffffa6263948>] kasan_report+0x58/0x60
[<ffffffffa6814b00>] ? rb_last+0x10/0x40
[<ffffffffa66f8af4>] ? setup_cluster_bitmap+0xc4/0x5a0
[<ffffffffa6262ead>] __asan_load8+0x5d/0x70
[<ffffffffa66f8af4>] setup_cluster_bitmap+0xc4/0x5a0
[<ffffffffa66f675a>] ? setup_cluster_no_bitmap+0x6a/0x400
[<ffffffffa66fcd16>] btrfs_find_space_cluster+0x4b6/0x640
[<ffffffffa66fc860>] ? btrfs_alloc_from_cluster+0x4e0/0x4e0
[<ffffffffa66fc36e>] ? btrfs_return_cluster_to_free_space+0x9e/0xb0
[<ffffffffa702dc37>] ? _raw_spin_unlock+0x27/0x40
[<ffffffffa666a1a1>] find_free_extent+0xba1/0x1520
Andrey noticed this was because we were doing list_first_entry on a list
that might be empty. Rework the tests a bit so we don't do that.
Signed-off-by: Chris Mason <clm@fb.com>
Reprorted-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Dave Jones <dsj@fb.com>
The code for switching to irq_stack stores three pieces of information on
the stack, fp+lr, as a fake stack frame (that lets us walk back onto the
interrupted tasks stack frame), and the address of the struct pt_regs that
contains the register values from kernel entry. (which dump_backtrace()
will print in any stack trace).
To reduce this, we store fp, and the pointer to the struct pt_regs.
unwind_frame() can recognise this as the irq_stack dummy frame, (as it only
appears at the top of the irq_stack), and use the struct pt_regs values
to find the missing interrupted link-register.
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
Ido Schimmel says:
====================
This patchset introduces support for the offloading of 802.1D bridges
between VLAN devices. These can either be VLAN devices configured on top
of the physical ports or on top of LAG devices.
Patches 1-2 deal with the necessary infrastructure changes needed in order
to enable the above. The main change is that switchdev drivers can now know
the device from which the switchdev op originated from.
Patches 3-10 lay the groundwork for 802.1D bridges support in the mlxsw
driver, with patch 4 doing most of the heavy lifting.
Patch 11 finally offloads these bridges to hardware by listening to the
notifications sent when the VLAN device joins or leaves a bridge. It is
very similar to the already existing 802.1Q bridge we support.
Patches 12-14 add minor modifications to allow one to bridge a VLAN device
configured on top of LAG.
====================
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a VLAN device on top of LAG, we are basically creating a
vPort on top of each of the port netdevs member in the LAG. Therefore,
these vPorts should inherit both the LAG status and LAG ID from the
underlying port netdevs.
In addition, when the VLAN device joins or leaves a bridge each of the
underlying vPorts should know about it and act accordingly. This is
achieved by propagating the VLAN event down to the lower devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding or removing FDB records of VLAN devices on top of LAG we
should set the lag_vid parameter to the VLAN ID of the VLAN device. It
is reserved otherwise.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unicast LAG records in the Switch Filtering Database (SFD) register have
a lag_vid field indicating the VLAN ID in case of vFIDs. This field is
no longer reserved since we are going to add support for VLAN devices on
top of LAG.
Add the lag_vid field to be used by VLAN devies on top of LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the member VLAN devices in a bridge need to share the same vFID.
To achieve that, expand the vFID struct to include the associated bridge
device (or lack of) and allow one to lookup a vFID based on a bridge
device.
When joining a bridge, lookup the relevant vFID or create one if none
exists. Next, make the VLAN device use the vFID.
Leaving a bridge can either occur because a user removed the VLAN device
from a bridge or because the VLAN device was deleted by the user. In the
latter case the bridge's teardown sequence is invoked after the hardware
vPort is already gone. Therefore, when unlinking the VLAN device from
the real device, check if the associated vPort is bridged and act
accordingly. The bridge's notification will be ignored in this case.
Note that bridging a VLAN interface with an ordinary port netdev is
currently not supported, but not forbidden. This will be addressed in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface is configured on top of a physical port we should
associate the VLAN device with the matching vPort. Likewise, when it's
removed, we should revert back to the underlying port netdev.
While not a must, this is consistent with port netdevs and also provides
a more accurate error printing via netdev_err() and friends.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications contain the FID and port (or LAG ID) on which the MAC
was learned. In the case of the 802.1Q bridge one can easily derive the
matching VID - as FID equals VID - and generate the appropriate
notification for the software bridge. With VLAN devices this is no
longer the case, as these are associated with a vFID.
Solve that by converting the FID to a vFID and lookup the matching VLAN
device. From that derive the VID and whether learning (and learning
sync) should occur.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev ops can now be called for VLAN devices and we need to be
prepared for it. Until now they were only called for the port netdev.
Use the newly propagated orig_dev passed as part of the switchdev
attr/obj and determine whether the original device is a VLAN device. If
so, act accordingly, otherwise continue as usual.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
