This patch adds support for the Cirrus Logic CS47L24 and WM1831 codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOC_xxx_DECL() macros already include 'const' so there's
no need to put a const in the source where they are used.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65086 PMIC regulators.
The regulators set consists of 3 Step-down Controllers, 3 Step-down
Converters, 3 LDOs, 3 Load Switches, and a Sink and Source LDO. The
output voltages are configurable and are meant to supply power to a
SoC and/or other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A binary search is much more efficient rather than iterating
over the rbtree in ascending order which the current code is
doing.
During initialisation the reg defaults are written to the
cache in a large chunk and these are always sorted in the
ascending order so for this situation ideally we should have
iterated the rbtree in descending order.
But at runtime the drivers may write into the cache in any
random order so this patch selects to use a bsearch to give
an optimal runtime performance and also at initialisation
time when reg defaults are written the performance of binary
search would be much better than iterating in ascending order
which the current code was doing.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API has an endianness setting for formatting reads and writes.
This can be set by the usual DT "little-endian" and "big-endian" properties.
To work properly the associated regmap_bus needs to read/write in native
endian.
The "syscon" DT device binding creates an mmio-based regmap_bus which
performs all reads/writes as little-endian. These values are then converted
again by regmap, which means that all of the MIPS BCM boards (which are
big-endian) have been declared as "little-endian" to get regmap to convert
them back to big-endian.
Modify regmap-mmio to use the native-endian functions __raw_read*() and
__raw_write*() instead of the little-endian functions read*() and
write*().
Modify the big-endian MIPS BCM boards to use what will now be the correct
endianness instead of pretending that the devices are little-endian.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Classify the functions at the DVB core per API. That makes easier
to understand how they're related to the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is better to keep the documentation overview at the header file,
as this makes easier for developers to remember to fix when needed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWSSq2AAoJEHm+PkMAQRiGIpQH/2Ro7UPwLARfZyd7GKpCRd/D
y1aJEk9GaEywkGKPd/Hf3XU+/9vxqyTWhkvpKHkGAFqzuYvw2rSE1JZnGfA+dyt/
1R/WSKM8f3VL2xmNmRJCXH+zn3W2u8Cvk0oj8VN0hseXByQfCT4HfoHiFrNwuo/9
63f93Dqsai1G3CBy+/HSPEv5CGR+7yeTJFWS0hQK4kc3prmitI93C5PZkyePyAId
wrgKo320rIcNL/lEAbMFEBimAqluIjGvdrR9FK6w3F+OwSlTV1HdSwTzNjxwdpP5
aRKNHZMdsGlShsn12Wsp+mjVFpi9OrT8Askq+/GTDsG+9QMia/gUKC21K9b6UxM=
=byS9
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc1' into patchwork
Linux 4.4-rc1
* tag 'v4.4-rc1': (12900 commits)
Linux 4.4-rc1
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
f2fs: xattr simplifications
squashfs: xattr simplifications
9p: xattr simplifications
xattr handlers: Pass handler to operations instead of flags
jffs2: Add missing capability check for listing trusted xattrs
hfsplus: Remove unused xattr handler list operations
ubifs: Remove unused security xattr handler
vfs: Fix the posix_acl_xattr_list return value
vfs: Check attribute names in posix acl xattr handers
mpt3sas: fix inline markers on non inline function declarations
dax: fix __dax_pmd_fault crash
Revert "drm/rockchip: Convert the probe function to the generic drm_of_component_probe()"
drm: Don't oops in drm_calc_timestamping_constants() if drm_vblank_init() wasn't called
ALSA: pci: depend on ZONE_DMA
...
Although kernel doesn't support the multiple IRQ priority levels provided
by HS38x core intc yet, ensure that the default prio value is used
anyways by relevant code.
SLEEP insn needs to be provided the IRQ priority level which can
interrupt it. This needs to be the default level which maynot
necessarily be 0 as assumed by current code.
This change allows a kernel with ARCV2_IRQ_DEF_PRIO = 1 to boot fine.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently, reset_controller_register() always return 0, but it would
be better to check its return code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The directory drivers/reset/ is guarded by CONFIG_RESET_CONTROLLER
in driver/Makefile.
CONFIG_RESET_CONTROLLER is boolean, so it always evaluates to 'y'
in drivers/reset/Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ENOSYS is reserved to report invalid syscalls to userspace.
Consistently return ENOTSUPP to indicate that the driver doesn't support
the functionality or the reset framework is not enabled at all.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since this array is static const, it should be marked as __initconst.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This just fixes a checkpatch warning, no functional change.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
When of_reset_control_get() is called without connection ID it returns
-ENOENT when the 'resets' property doesn't exists or is an empty entry.
However when a connection ID is given it returns -EINVAL when the 'resets'
property doesn't exists or the requested name can't be found. This is
because the error code returned by of_property_match_string() is just
passed down as an index to of_parse_phandle_with_args(), which then
returns -EINVAL.
To get a consistent return value with both code paths we must return
-ENOENT when of_property_match_string() fails.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add of_reset_control_get_by_index() to allow the drivers to get reset
device without knowing its name.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
[jonathanh@nvidia.com: Updated stub function to return -ENOTSUPP instead
of -ENOSYS which should only be used for system calls.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Commit 939f325f4a ("usb: add usb_endpoint_maxp() macro") and commit
29cc88979a ("USB: use usb_endpoint_maxp() instead of le16_to_cpu()")
introduced a new helper macro. This trivial patch convert remaining
users found in ua101 driver.
Signed-off-by: Cheah Kok Cheong <thrust73@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
correct: CH345:
0F FE 00 00 0F FE 00 00
04 F0 01 02 04 F0 01 02
04 03 04 05 0F 03 04 05
04 06 07 08 04 06 07 08
04 09 0A 0B 0F 09 0A 0B
04 0C 0D 0E 04 0C 0D 0E
05 F7 00 00 05 F7 00 00
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a header file that defines the clock numbers for Tegra210. It is
meant to be included by device trees so that they can refer to the
clocks by symbolic name instead of numeric value.
Also add the device tree binding documentation which is largely the
same as for earlier generations of Tegra.
Extracted from a larger patch by Rhyland Klein <rklein@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When building kernel with buildroot built toolchain, CROSS_COMPILE
currently needs adjustment even if minor. This is because the defconfigs
prefer "arc-linux-uclibc-" prefix from hand built (non buildroot) toolchain
while buildroot provides "arc-buildroot-linux-uclibc-"
To avoid this use the common "arc-linux-" prefix which is provided by
buildroot and has also been in hand built tools for quite some time.
Signed-off-by: sujayraaj <sujayraaj@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: updated changelog]
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Fixes: a0de56c81f ("hwmon: (ina2xx) convert driver to using regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare the function fwtty_port_put as static since it is used
only in this particular file. Also remove the corresponding
declaration from header file.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the one-shot LCB write implemented in the 8051 firmware.
This speeds up 8051 LCB writes by 2x. Use old method for older
firmwares.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changed the order in which diagnostics messages are printed,
taking into account the cases where the errors are handled in
rcv_hdrerr() and no further message is needed to report.
Reviewed-by: Mark Debbage <mark.debbage@intel.com>
Reviewed-by: Arthur Kepner <arthur.kepner@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ignacio Hernandez <ignacio.hernandez@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
opaportconfig ledon fails with error message due to port
number being checked in the attr modifier. This change
removes the check for the port number in AttrMod, so the
P field is ignored.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When looking for or validating a user device, only use devices
that are currently active.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During driver load the thermal sensor needs to be reset prior
to initialization of the sensor. This prevents a possible sensor lock
up which can cause the wrong temperature value to be reported.
This fix leads to remove disabling thermal polling from
reset_asic_csrs() function.
Reviewed by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Jareer Abdel-Qader <jareer.h.abdel-qader@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
B0 dual port parts require the SBus firmware to always be
downloaded.
Remove reset of the SBus Master spico. It is not necessary
since the SBus firmware download already does that.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS implementations turn off extended tags in DevCtl (a RW
field) even though it was originally set and is advertised in DevCap
Fix is to set it in the driver
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vennila Megavannan <vennila.megavannan@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FLR on driver load asserts the QSFP reset pin and the driver does
not deassert it after. This patch allows the external QSFP cable to exit
reset by writing 1 to all the QSFP pins.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing dd_dev_info() for hfi1_cdbg() to avoid generating syslog
output for every context that is open by PSM.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second argument name of DIM_GetChannelState declaration changes from
dim_ch_state_ptr to state_ptr. The DIM_GetChannelState declaration and
definition has same argument name as state_ptr.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
