Add 8kHz, 11.025kHz, 16kHz, 22.05kHz output sample rate support.
According referance menual, "Limited support for the case when
output sampling rates is between 8kHz and 30kHz. The limitation
is the supported ratio (Fsin/Fsout) range as between 1/24 to 8."
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Sometimes the audio play can not be resumed after it is
suspended. Add snd_soc_pm_ops to execute power management
operations, then this issue is fixed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
* x = devm_kzalloc(...);
... when != x == NULL
*x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usb is very much like on am33xx, we just put the some of the
componends under scm where they belong.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a 2GB emmc on hp t410 that's wired to the sd_2 interface.
Note that we also need to configure the evtmux using edma_xbar for
edma channels.
Let's use the McASP2 channels like the original kernel seems to be
doing, most likely the audio on t410 is different from dm814x-evm.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The edma is the same as on am33xx, except it has four tptc
instances. And we need the edma_xbar for at least mmc3, so
let's use the edma_xbar and the new binding as suggested by
Peter Ujfalusi <peter.ujfalusi@ti.com>.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for ti,edma-memcpy-channels binding]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add the DM814X_IOPAD macro the same way as we have for dm816x and
am33xx as this allows comparing the registers with the documentation easily.
The pinctrl bits are yet again different on dm814x.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull block layer fixes from Jens Axboe:
"Three small fixes for 4.4 final. Specifically:
- The segment issue fix from Junichi, where the old IO path does a
bio limit split before potentially bouncing the pages. We need to
do that in the right order, to ensure that limitations are met.
- A NVMe surprise removal IO hang fix from Keith.
- A use-after-free in null_blk, introduced by a previous patch in
this series. From Mike Krinkin"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: fix use-after-free error
block: ensure to split after potentially bouncing a bio
NVMe: IO ending fixes on surprise removal
The dra762x j5-eco is similar to dm814x with a bit different clocks
and devices.
[tony@atomide.com: updated to leave out adpll clock driver references]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the ssm2518_lookup_mcs()
function even though it will eventually return a negative error code.
Improve this implementation detail by deletion of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to the codec driver to handle mic level
detect related IRQs, and report these to user-space using a uevent
variable.
The uevent variable string "EVENT=MIC_LEVEL_DETECT" is sent to
user-space, if the mic level detect feature is enabled, and the
audio captured at the chosen mic(s) is above a certain threshold.
User-space can then handle the event accordingly (e.g. process
audio capture stream).
This method was chosen over ALSA control notification for a couple
of reasons:
1) There's no requirement here for a control to read state from.
The event is the only thing that's required and of interest.
2) tinyalsa support for control notifications does not exist so on
platforms using this over alsa-lib there is a need to add code
to support this event handling.
Another possible option would be to use the standard Jack reporting
framework but this really does not fit for this kind of event.
Finally, use of the input device framework is not being encouraged,
due to difficulties in enabling apps to access input devices, so
this has also been avoided.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An external amp (if any) is connected to the external outputs of the SoC
of course, rather then directly to the internal amp.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UJhV
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.4-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fix from Bruce Fields:
"Just one fix for a NFSv4 callback bug introduced in 4.4"
* tag 'nfsd-4.4-1' of git://linux-nfs.org/~bfields/linux:
nfsd: don't hold ls_mutex across a layout recall
AFE is actually allowed to be turn on before configuration of DAIs
since each DAI has its own enabling control. Turn on/off AFE in
runtime resume/suspend to avoid AFE being shut down when closing a DAI
while other DAIs are still active.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- A series of fixes to the MTRR emulation, tested in the BZ by several users
so they should be safe this late
- A fix for a division by zero
- Two very simple ARM and PPC fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWeV/6AAoJEL/70l94x66DqzsH/05YnLi2GsX5WeZHMfIUgzgT
S/GoIkA7A4E2eXVoGg824MWppSViUzZkWgYFQTG4+KY9WPXzm9z2ij7DIlUHCD6n
QfevgQx1kIu1obyhm6bYM2xUdM3f7NCsQgw9bXZObB0ay+b/+GjR9/RbCbx60EO5
K1P+kveK6PFlS9/hc0PLztu6WkPV9BCO1RJUbeAEdnrMbpuQfHC+coR7MHRCiv2V
iy8f1CqrGaO5YPm9/3GbdH1xMKew4OZShOxTXwtvUThdrLkks2c8sk6FoLzqkznH
LMHVIpkm4mrIgThZG7VqZMXOrWvBtsCt04Vr9MzCM6QetB02b/Uz0xKvMYx2kZQ=
=pmYz
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- A series of fixes to the MTRR emulation, tested in the BZ by several
users so they should be safe this late
- A fix for a division by zero
- Two very simple ARM and PPC fixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Reload pit counters for all channels when restoring state
KVM: MTRR: treat memory as writeback if MTRR is disabled in guest CPUID
KVM: MTRR: observe maxphyaddr from guest CPUID, not host
KVM: MTRR: fix fixed MTRR segment look up
KVM: VMX: Fix host initiated access to guest MSR_TSC_AUX
KVM: arm/arm64: vgic: Fix kvm_vgic_map_is_active's dist check
kvm: x86: move tracepoints outside extended quiescent state
KVM: PPC: Book3S HV: Prohibit setting illegal transaction state in MSR
Pull s390 fixes from Martin Schwidefsky:
"Two late bug fixes for kernel 4.4.
Merry Christmas"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dis: Fix handling of format specifiers
s390/zcrypt: Fix AP queue handling if queue is full
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960 ("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
We can boot dra62x j5-eco using the dm814x code as the clocks and
devices are mapped in the device tree. The dra62x is also known
as jacinto 5 eco.
We may want to add separate soc_is macros for dra62x if needed,
but this gets us to the point where we can boot dra62x with just
dts changes.
Let's also print out the unknown hawkeye register to make things
a bit easier for new SoC variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This includes a single fix for virtio ccw error handling.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWdmeoAAoJECgfDbjSjVRpArwIAKuaWLdfu6Aj25QkiENb5PFu
JghRoy8P1SdGTqNdjbvG1XkxI072rWfrvU+cmVx9GbeZgusWtbeiTeBNT/jXnH/5
hodG9YdUEZOh2WhROQ+Fo7t1vzqvBWHuU9YdrBnHDbdFQ8300CgNTOsdih2rlEfT
t5/R3BEE0DXGTXTc3vO35+DVXzX8PA2FD18W7trrAjN7M5DdhCu98Q2VcvMZY/D6
aSBDPMJZxR0YcRPE97w0dZMLePCYkfmoLryVCVVXm5VZq6zXc7Dhm6ND0/oH+0DB
f4jxjapNUy+RAmE378ACsVwT992TTk49ZGZjbt4ttGOfFYDTrErrDkCq9QaZX7o=
=xgGU
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fix from Michael Tsirkin:
"This includes a single fix for virtio ccw error handling"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: handle error values in irb
Fix a pointer cast typo introduced in v4.4-rc5 especially visible for
the i386 subarchitecture where it results in a kernel crash.
[ Also removed pointless cast as per Al Viro - Linus ]
Fixes: 8090bfd2bb ("um: Fix fpstate handling")
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Jeff Dike <jdike@addtoit.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes from Liviu add support for atomic mode setting, add the
TMDS clock limitation according to the device, and ensure that we
correctly clean up in the unbind function.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: Add support for atomic modesetting
drm/i2c: tda998x: increase the supported dotclock frequency to 165MHz for TDA19988
drm/i2c: tda998x: unregister the connector in the unbind function
These are the patches from Daniel Vetter, getting rid of struct_mutex
from the Armada DRM driver.
* 'drm-armada-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: use a private mutex to protect priv->linear
drm/armada: drop struct_mutex from cursor paths
drm/armada: don't grab dev->struct_mutex for in mmap offset ioctl
drm/armada: plug leak in dumb_map_offset
drm/armada: use unlocked gem unreferencing
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Support Sigma Designs ARM-based (specifically, Cortex-A9 MPCore r3p0)
Tango4 "Secure Media Processor" platforms: smp8756, smp8758, smp8759
(8756 is single-core, the latter are dual-core).
Note: 8758 vs 8759: same chip, different package.
Support for older MIPS-based platforms can be found elsewhere:
https://github.com/mansr/linux-tangox
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use subsys_initcall to init qe to adapt ARM architecture.
Remove qe_reset from PowerPC platform file.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
QE and CPM have the same muram, they use the same management
functions. Now QE support both ARM and PowerPC, it is necessary
to move QE to "driver/soc", so move the muram management functions
from cpm_common to qe_common for preparing to move QE code to "driver/soc"
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use genalloc to manage CPM/QE muram instead of rheap.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add new algo for genalloc, it reserve a specific region of
memory
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Bytes alignment is required to manage some special RAM,
so add gen_pool_first_fit_align to genalloc,
meanwhile add gen_pool_alloc_algo to pass algo in case user
layer using more than one algo, and pass data to
gen_pool_first_fit_align(modify gen_pool_alloc as a wrapper)
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1z4m
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT patches, round 2
Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.
* tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun5i: Add dts file for the Empire Electronix D709 tablet
ARM: dts: sun7i: Enable gmac on Wits Pro A20 DKT
ARM: dt: sun7i: Enable audio codec on MK808C
ARM: sunxi: dt: enable audio codec on mk802
ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet
ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
ARM: dts: sun4i: gemei-g9: Enable PA GPIO pin configuration
ARM: dts: sun4i: Enable onboard codec used on the pov protab2-ips9 tablet
ARM: dts: sun5i: Enable onboard codec used on the UTOO P66 tablet
Signed-off-by: Olof Johansson <olof@lixom.net>
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XTmq
-----END PGP SIGNATURE-----
Merge tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Second batch of DT changes for 4.5:
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo
* tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91/dt: sama5d2 Xplained: add pdmic node
ARM: at91/dt: sama5d2: add pdmic node
ARM: at91/dt: Add Support for the L+G VInCo platform
Signed-off-by: Olof Johansson <olof@lixom.net>
