Commit fa37a9586f ('mlx4_en: Moving to
work with GRO') left behind the Kconfig depends/select, some dead
code and comments referring to LRO.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wireless and wext includes in net-sysfs.c aren't
needed, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_tasklet is a struct, not a pointer in percpu var.
so use this_cpu_ptr to get the member pointer.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
md_stop() would stop an array, but not free various attached
data structures.
For internal arrays, these are freed later in do_md_stop() or
mddev_put(), but they don't apply for dm-raid arrays.
So get md_stop() to free them, and only all it from dm-raid.
For internal arrays we now call __md_stop.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If read_seqretry returned true and bbp was changed, it will write
invalid address which can cause some serious problem.
This bug was introduced by commit v3.0-rc7-130-g2699b67.
So fix is suitable for 3.0.y thru 3.6.y.
Reported-by: zhuwenfeng@kedacom.com
Tested-by: zhuwenfeng@kedacom.com
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced by commit(v3.0-rc7-126-g2230dfe).
So fix is suitable for 3.0.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Daniel writes:
Highlights of this -next round:
- ivb fdi B/C fixes
- hsw sprite/plane offset fixes from Damien
- unified dp/hdmi encoder for hsw, finally external dp support on hsw
(Paulo)
- kill-agp and some other prep work in the gtt code from Ben
- some fb handling fixes from Ville
- massive pile of patches to align hsw VGA with the spec and make it
actually work (Paulo)
- pile of workarounds from Jesse, mostly for vlv, but also some other
related platforms
- start of a dev_priv reorg, that thing grew out of bounds and chaotic
- small bits&pieces all over the place, down to better error handling for
load-detect on gen2 (Chris, Jani, Mika, Zhenyu, ...)
On top of the previous pile (just copypasta):
- tons of hsw dp prep patches form Paulo
- round scheduled work items and timers to nearest second (Chris)
- some hw workarounds (Jesse&Damien)
- vlv dp support and related fixups (Vijay et al.)
- basic haswell dp support, not yet wired up for external ports (Paulo)
- edp support (Paulo)
- tons of refactorings to prepare for the above (Paulo)
- panel rework, unifiying code between lvds and edp panels (Jani)
- panel fitter scaling modes (Jani + Yuly Novikov)
- panel power improvements, should now work without the BIOS setting it up
- extracting some dp helpers from radeon/i915 and move them to
drm_dp_helper.c
- randome pile of workarounds (Damien, Ben, ...)
- some cleanups for the register restore code for suspend/resume
- secure batchbuffer support, should enable tear-free blits on gen6+
Chris)
- random smaller fixlets and cleanups.
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (231 commits)
drm/i915: Restore physical HWS_PGA after resume
drm/i915: Report amount of usable graphics memory in MiB
drm/i915/i2c: Track users of GMBUS force-bit
drm/i915: Allocate the proper size for contexts.
drm/i915: Update load-detect failure paths for modeset-rework
drm/i915: Clear unused fields of mode for framebuffer creation
drm/i915: Always calculate 8xx WM values based on a 32-bpp framebuffer
drm/i915: Fix sparse warnings in from AGP kill code
drm/i915: Missed lock change with rps lock
drm/i915: Move the remaining gtt code
drm/i915: flush system agent TLBs on SNB
drm/i915: Kill off now unused gen6+ AGP code
drm/i915: Calculate correct stolen size for GEN7+
drm/i915: Stop using AGP layer for GEN6+
drm/i915: drop the double-OP_STOREDW usage in blt_ring_flush
drm/i915: don't rewrite the GTT on resume v4
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
drm/i915: put ring frequency and turbo setup into a work queue v5
drm/i915: don't block resume on fb console resume v2
drm/i915: extract l3_parity substruct from dev_priv
...
In target mode, sent sk_buff were not freed in pn533_tm_send_complete
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd is allocated in pn533_dep_link_up and passed as an arg to
pn533_send_cmd_frame_async together with a complete cb.
arg is passed to the cb and must be kfreed there.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd was freed in pn533_dep_link_up regardless of
pn533_send_cmd_frame_async return code. Cmd is passed as argument to
pn533_in_dep_link_up_complete callback and should be freed there.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In pn533_wq_cmd command was removed from list without cmd_lock held
(race with pn533_send_cmd_frame_async) which could lead to list
corruption. Delete command from list before releasing lock.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
list_add was called with swapped parameters
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Drivers are allowed to modify the sent skb and thus we need to make a copy
of it before passing it to the driver. Without this fix, LLCP Tx skbs were
not queued properly as the ptype check was failing due to e.g. the pn533
driver skb_pushing the Tx skb.
Reported-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the tx pending queues and/or the socket tx queue is getting too deep,
we have to let userspace know. We won't be queueing any more frames until
the congestion is fixed.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The platform data header for PN544 based NFC devices should
also be mentioned here.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pn544.h just provides the platform data struct and defines and
nothing else. So move it to to linux/platform_data/ now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The majority of the defines and structures from pn544.h are no
longer in use. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A chip with pre-opened gates may send events on a gate that nobody
has opened in the handset host. Discard those events.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_HCI_ID_MGMT_VERSION_SW and NFC_HCI_ID_MGMT_VERSION_HW are optional
registers for gate NFC_HCI_ID_MGMT_GATE in standard HCI. When chip
doesn't implement, just leave all the information as zeros.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some cases, pre-opened pipes don't stay open when a clear all pipes
command is sent. They stay created however. Therefore, one can never
assume that such a pipe is already open. As re-opening a pipe seems not
to be a problem, we do that now.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The recent cleanups have decimated the drivers code size by quite a bit. It is
only a few hundred lines in total now. Putting everything into one file also
allows to reduce the code size a bit more by removing a few lines of boilerplate
code. The only functional change made by this patch is that we now always
include buffer support, instead of making it optional. This is more consistent
with what we do for other drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The temperature scale and offset depend on the reference voltage, the current
formula used in the driver assumes a 2.5V reference. This patch modifies the
code to report the unprocessed value for the temperature channel "raw" property
and to provide proper "scale" and "offset" properties which depend on the
selected reference voltage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Rework the regulator handling of the driver to match more closely what we do in
other drivers. Make the regulator non-optional if a external reference is used.
Also dispose the option of specifying the reference voltage via platform data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For buffered mode we do not want to perform endianness conversion in the kernel,
but rather offload it to user space, since it is not always required to do a
conversion at all. It also greatly simplifies the kernel code since no
post-processing has to be done and may allow future optimizations like streaming
data directly to a storage device or over the network via DMA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.
While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the driver reads out all sample registers of the device and throws
away those which it does not need. Furthermore the SPI message is constructed
each time the trigger handler is run, although it will be the same each time.
This patch preallocates and pre-constructs the SPI message in the
"update_scan_mode" callback. Only those register which are actually selected for
sampling are included in the message. The patch also gets rid of the conversion
of the sample data from big endian to the native endianness and instead marks
the channel as big endian in its scan type. This allows to directly push the
SPI transfer buffer to the IIO buffer without the need to post-process it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the triggered buffer helper functions to setup and tear down the buffer for
the adis library instead of doing this manually. This also means that we switch
away from the deprecated sw_ring buffer and use the kfifo buffer now instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16260 driver. This allows us to completely
scrap the adis16260 buffer and trigger code and about half of the core driver
code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16240 driver. This allows us to completely
scrap the adis16240 buffer and trigger code and more than half of the core
driver code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16220 driver. The adis16220 driver is a bit
special and so we can only make use of the generic register access and control
functions for now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16209 driver. This allows us to completely
scrap the adis16209 buffer and trigger code and more than half of the core
driver code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16204 driver. This allows us to completely
scrap the adis16204 buffer and trigger code and more than half of the core
driver code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16203 driver. This allows us to completely
scrap the adis16203 buffer and trigger code and more than half of the core
driver code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16201 driver. This allows us to completely
scrap the adis16201 buffer and trigger code and more than half of the core
driver code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A lot of the devices from the ADIS family use the same methods for accessing
registers, sampling data and trigger handling. They also have similar register
layout for the control registers.
This patch adds a common library for these devices. The library implements
functions for reading and writing registers as buffer and trigger management. It
also provides a set functions for accessing the control registers and for
running the devices internal self-test. Having this common library code will
allow us to remove a lot of duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We had assigned the return value to 'ret' but ignored it when
return from isl29018_write_raw(), it's better to return 'ret'
instead of 0.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Match the iio_buffer_register stub signature up to the real function and make
the second parameter const. This fixes a the following warnings if
CONFIG_IIO_BUFFER is disabled:
drivers/staging/iio/accel/adis16201_core.c: In function ‘adis16201_probe’:
drivers/staging/iio/accel/adis16201_core.c:536: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16203_core.c: In function ‘adis16203_probe’:
drivers/staging/iio/accel/adis16203_core.c:468: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16204_core.c: In function ‘adis16204_probe’:
drivers/staging/iio/accel/adis16204_core.c:527: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16209_core.c: In function ‘adis16209_probe’:
drivers/staging/iio/accel/adis16209_core.c:542: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16240_core.c: In function ‘adis16240_probe’:
drivers/staging/iio/accel/adis16240_core.c:588: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make perf build for x86 once the UAPI disintegration patches for that arch
have been applied by adding the appropriate -I flags - in the right order -
and then converting some #includes that use ../.. notation to find main kernel
headerfiles to use <asm/foo.h> and <linux/foo.h> instead.
Note that -Iarch/foo/include/uapi is present _before_ -Iarch/foo/include.
This makes sure we get the userspace version of the pt_regs struct. Ideally,
we wouldn't have the latter -I flag at all, but unfortunately we want
asm/svm.h and asm/vmx.h in builtin-kvm.c and these aren't part of the UAPI -
at least not for x86. I wonder if the bits outside of the __KERNEL__ guards
*should* be transferred there.
I note also that perf seems to do its dependency handling manually by listing
all the header files it might want to use in LIB_H in the Makefile. Can this
be changed to use -MD?
Note that to do make this work, we need to export and UAPI disintegrate
linux/hw_breakpoint.h, which I think should've been exported previously so that
perf can access the bits. We have to do this in the same patch to maintain
bisectability.
Signed-off-by: David Howells <dhowells@redhat.com>
Use the 'unistd.h' from arch/powerpc/include/uapi to build the perf tool.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20121107191818.GA16211@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fixing:
[acme@sandy linux]$ cd tools
[acme@sandy tools]$ make clean
DESCEND power/cpupower
CC lib/cpufreq.o
CC lib/sysfs.o
LD libcpupower.so.0.0.0
CC utils/helpers/amd.o
utils/helpers/amd.c:7:21: error: pci/pci.h: No such file or directory
In file included from utils/helpers/amd.c:9:
./utils/helpers/helpers.h:137: warning: ‘struct pci_access’ declared inside parameter list
./utils/helpers/helpers.h:137: warning: its scope is only this definition or declaration, which is probably not what you want
./utils/helpers/helpers.h:139: warning: ‘struct pci_access’ declared inside parameter list
utils/helpers/amd.c: In function ‘amd_pci_get_num_boost_states’:
utils/helpers/amd.c:120: warning: passing argument 1 of ‘pci_slot_func_init’ from incompatible pointer type
./utils/helpers/helpers.h:138: note: expected ‘struct pci_access **’ but argument is of type ‘struct pci_access **’
utils/helpers/amd.c:125: warning: implicit declaration of function ‘pci_read_byte’
utils/helpers/amd.c:132: warning: implicit declaration of function ‘pci_cleanup’
make[1]: *** [utils/helpers/amd.o] Error 1
make: *** [cpupower_clean] Error 2
[acme@sandy tools]$
Reported-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-tviyimq6x6nm77sj5lt4t19f@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Honour the O= flag that was passed to a higher level Makefile and then passed
down as part of a tool build.
To make this work, the top-level Makefile passes the original O= flag and
subdir=tools to the tools/Makefile, and that in turn passes
subdir=$(O)/$(subdir)/foodir when building tool foo in directory
$(O)/$(subdir)/foodir (where the intervening slashes aren't added if an
element is missing).
For example, take perf. This is found in tools/perf/. Assume we're building
into directory ~/zebra/, so we pass O=~/zebra to make. Dependening on where
we run the build from, we see:
make run in dir $(OUTPUT) dir
======================= ==================
linux ~/zebra/tools/perf/
linux/tools ~/zebra/perf/
linux/tools/perf ~/zebra/
and if O= is not set, we get:
make run in dir $(OUTPUT) dir
======================= ==================
linux linux/tools/perf/
linux/tools linux/tools/perf/
linux/tools/perf linux/tools/perf/
The output directories are created by the descend function if they don't
already exist.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1378.1352379110@warthog.procyon.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define a Makefile function that can be called with $(call ...) to wrap
the subdir make invocations in tools/Makefile.
This will allow us in the next patch to insert bits in there to honour
O= flags when called from the top-level Makefile.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1378.1352379110@warthog.procyon.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Read Local OOB Data command can take more than 1 second on some chips.
e.g. on CSR 0a12:0001 first call to Read Local OOB Data after reset
takes about 1300ms resulting in tx timeout error.
[27698.368655] Bluetooth: hci0 command 0x0c57 tx timeout
2012-10-31 15:53:36.178585 < HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
2012-10-31 15:53:37.496996 > HCI Event: Command Complete (0x0e) plen 36
Read Local OOB Data (0x03|0x0057) ncmd 1
status 0x00
hash 0x92219d9b447f2aa9dc12dda2ae7bae6a
randomizer 0xb1948d0febe4ea38ce85c4e66313beba
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>