Here are two TTY driver fixes for 3.7-rc5.
They resolve a bug in the hvc driver that has been reported, and fix a
problem with the list of device ids in the max310x serial driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRekACgkQMUfUDdst+ym94QCfZXb34WBxejNff2PowH9GZ7zL
NNAAoLi2YFB68la0KYxQ8zWBakL/QeyZ
=w8fs
-----END PGP SIGNATURE-----
Merge tag 'tty-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are two TTY driver fixes for 3.7-rc5.
They resolve a bug in the hvc driver that has been reported, and fix a
problem with the list of device ids in the max310x serial driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: max310x: Add terminating entry for spi_device_id table
TTY: hvc_console, fix port reference count going to zero prematurely
Here is a single patch, a revert of an android driver patch, that
resolves a bug that has been reported in the Android alarm driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRx4ACgkQMUfUDdst+yl3DwCbB9ekMEOeU8kRPiFozI8m702t
JbsAnikKlAk+EmoufP46+3+PVKh7582d
=pRqt
-----END PGP SIGNATURE-----
Merge tag 'staging-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fix from Greg Kroah-Hartman:
"Here is a single patch, a revert of an android driver patch, that
resolves a bug that has been reported in the Android alarm driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: Android alarm: IOCTL command encoding fix"
another one fixing the check of a GPIO for USB host overcurrent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQphQoAAoJEAf03oE53VmQDs0H/1SCQfdQY8iLNs+3WGYhGngG
vMID1KWKmX6URrppi2gklr8weUoqYIVIA8I7+hLvr33tGrmSPRDrGV6vI5m0wAiJ
nkDNAkcGJ6dh/hhotakjqqKLkNtD1xDdErHMOO77fAK811gQj1sVp+8S+UwDQUf7
O1bbMpMar2/3c6cLb27GE7M4FrLwjmCnQxyQWyBrckPhPMzYNw3MbcW3CINXSYBY
q/FtFX7nsl2cfPsz8M2KCB43SKZT/bizkPnnjA5QQDhUPlsyTQWdS2z1RAwP2SZn
3WXoL4t4bNo1Ynusz416pB3djHqJwhxxWYxdMD91nIUXmmXkvIg+fWsdaNmaBI0=
=wlxI
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two little fixes, one related to the move to sparse irq and
another one fixing the check of a GPIO for USB host overcurrent.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull s390 patches from Martin Schwidefsky:
"Some more bug fixes and a config change.
The signal bug is nasty, if the clock_gettime vdso function is
interrupted by a signal while in access-register-mode we end up with
an endless signal loop until the signal stack is full. The config
change is for aligned struct pages, gives us 8% improvement with
hackbench."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/3215: fix tty close handling
s390/mm: have 16 byte aligned struct pages
s390/gup: fix access_ok() usage in __get_user_pages_fast()
s390/gup: add missing TASK_SIZE check to get_user_pages_fast()
s390/topology: fix core id vs physical package id mix-up
s390/signal: set correct address space control
The babbage board has a DVI-I output which allows to output analog
and digital signals simultaneously. This patch adds support for it
to the devicetree. The DDC signals are not wired up on the board, so
DRM will fall back on default VESA modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This adds the IPU device to the devicetree along with the necessary pinctrl
settings for the parallel display outputs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
The i.MX5 clk support has platform based clock bindings for the
IPU. IPU support is devicetree only, so move them over to devicetree
based bindings. Also, enable MIPI clocks which do not have a device
associated with, but still need to be enabled to do graphics on
i.MX51.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This adds the mmdc_ch1 as a possible parent for the ldb_di clk.
According to the datasheet, this clock can be selected at this mux.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
The MIPI interface has to be initialized for proper IPU support.
The MIPI officially is not supported, but still needs initialization.
This patch adds this to the SoC startup as all it does is poking
some magic values into registers for which we do not have documentation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Pull drm fixes from Dave Airlie:
"All pretty normal: one TTM oops fix, one radeon, a few intel and a
vmwgfx fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: remove unneeded preempt_disable/enable
ttm: Clear the ttm page allocated from high memory zone correctly
vmwgfx: return an -EFAULT if copy_to_user() fails
drm/radeon: fix logic error in atombios_encoders.c
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
Since mx27 transitioned to the commmon clock framework in 3.5, the correct way
to acquire the csi clock is to get csi_ahb and csi_per clocks separately.
By not doing so the camera sensor does not probe correctly:
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
mx2-camera mx2-camera.0: Camera driver attached to camera 0
ov2640 0-0030: Product ID error fb:fb
mx2-camera mx2-camera.0: Camera driver detached from camera 0
mx2-camera mx2-camera.0: MX2 Camera (CSI) driver probed, clock frequency: 66500000
Adapt the mx2_camera driver to the new clock framework and make it functional
again.
Tested-by: Gaëtan Carlier <gcembed@gmail.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During the clock conversion for mx27 the "per4_gate" clock was missed to get
registered as a dependency of mx2-camera driver.
In the old mx27 clock driver we used to have:
DEFINE_CLOCK1(csi_clk, 0, NULL, 0, parent, &csi_clk1, &per4_clk);
,so does the same in the new clock driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX27 clock tree can either be driven from a 26MHz oscillator
or from a 32768Hz oscillator. The latter was not properly implemented,
the mux between these two pathes was missing. Add this mux and while
at it rename the 'prem' (premultiplier) clk to 'fpm' (Frequency
Pre-Multiplier) to better match the datasheet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx27.dtsi already register the watchdog, so no need to do it in the board dts
file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes watchdog support after devicetree switch for imx53
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch enables support for i.MX53 in addition to i.MX25 by providing a
dummy clock on i.MX53 since this one doesn't have a separate clock for internal
RTC but the driver requests one.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is to prepare addition of m2m-emmapp driver otherwise
IMX_HAVE_PLATFORM_MX2_CAMERA must be declared even if only Post-Processor is
needed.
IMX_HAVE_PLATFORM_MX2_EMMA define has been added.
Changes since v1:
- Add "select IMX_HAVE_PLATFORM_MX2_EMMA" for MACH_IMX27_VISSTRIM_M10 platform
due to pending patch in linux-media tree that will call
imx27_add_mx2_emmaprp().
Signed-off-by: Gaëtan Carlier <gcembed@gmail.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
clk-provider.h. This pull request fixes the regression by removing inline
usage from those function declarations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQpUWqAAoJEDqPOy9afJhJGxIQAIUDNow/T5KmaddVxWB6CfTz
wkxmgNHJ0pPZPVrWJt7kpp2jEdHVk2opVaacMVvKJqMoqliMqVUMYVzkTcjmq4UH
xNAQnR60Kte49tuk4QkeT2AMndAAY9Wo/JBl+LPRuRP2bniAzY8UhBqeWto/jdO5
2MvpUHMfzhobhGDJX1kGCbUYKZlxW06AdGSfcXFmZdlmHlWtH2ZIvDhdg/n9pLEX
mR8xhqxIQxe9rwDkG/fjoBn6RM8v52bJUBDglRwu6ns7eczNcKcjsLQ55ddqJLqT
HTII/e9KI63nAi1NmmG7+lSzb7yYxOx7qSNJ2DSRU54BKJiTXqj3IHaZbrHA84Zt
7d7iUu/MsXkR5h++m7p5CAtgwxelHyldN++ohQwVYs0wBRFIrVDGXnUqrT5vL9hV
jh+nYRAF/k8swE2wYqqYTbpOA1AHwg58/WLdqi72NntzbLqueBuaB1oJyL9v1xtp
6rP2mSSo83i2uo3YXh7OYV4waHFEffzk4idzXWv6tVTfNKaADYwtUyvH7Te0rQeU
cJHO80mqyvZblI3yrVETU4KRrkHbDqHtGGUMW/aCMY/7K8RrSZdZEZVN2BY1+lip
cgd8jPJf2M98yGsM2jcvyLdQw+0ZMb+pVSkOyGHZPsKmSE18xeb/HDh7uP6Y8u9m
SJwr7bu2ojf5w2AcFCRH
=Y6xa
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull another clk layer fix from Michael Turquette:
"GCC 4.7 users get compilation errors from unnecessary use of inline in
clk-provider.h. This pull request fixes the regression by removing
inline usage from those function declarations."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: remove inline usage from clk-provider.h
I ported the driver supplied by SystemBase to mainline.
As the driver had MODULE_LICENSE("GPL") it is declared as a GPL module
and thus I have the right to distribute it upstream. Note, I did the
bare minimum to get it working. It still needs a lot of loving.
Cc: hjchoi <hjchoi@sysbas.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets HPM (Host power mask bit) to bit 16 according to i.MX
Reference Manual. Falsely it was set to bit 8, but this controls pull-up
Impedance.
Reported-by: Michael Burkey <mdburkey@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The error-valued pointer clk is used for the arg of kfree, it should be
kfree(gate) if clk_register() return ERR_PTR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested on an at91sam9260 board (evk-pro3).
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested on an at91sam9260 board (evk-pro3)
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds a return code check after attempting to allocate
a new inode during dinode creation.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch changes the block allocation trace so that it references
the rgd's glock rather than the inode's glock. Now that the order
of inode creation is switched, this prevents a reference to the
glock which may not be set yet.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Currently we just queue the transfer and release the
qos constraints, however we do not wait for the transfer
to complete to release the constraint. Move the remove
constraint after the bus busy as we are sure that the
transfers are completed by then.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This was always racy, but 268720903f
"uprobes: Rework register_for_each_vma() to make it O(n)" should be
blamed anyway, it made everything worse and I didn't notice.
register/unregister call build_map_info() and then do install/remove
breakpoint for every mm which mmaps inode/offset. This can obviously
race with fork()->dup_mmap() in between and we can miss the child.
uprobe_register() could be easily fixed but unregister is much worse,
the new mm inherits "int3" from parent and there is no way to detect
this if uprobe goes away.
So this patch simply adds percpu_down_read/up_read around dup_mmap(),
and percpu_down_write/up_write into register_for_each_vma().
This adds 2 new hooks into dup_mmap() but we can kill uprobe_dup_mmap()
and fold it into uprobe_end_dup_mmap().
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
After improving the clock tree we need to make sure the the
MTU timer explicitly grabs and enables it silicon clock
(pclk).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
In the case of timeout waiting for data ready, the retry variable is -1.
This also fixes a bug: current code returns -ETIMEDOUT if latest retry success
( which means retry is 0 when exiting the while loop ).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392142 moved event buffer allocation out of dwc3_core_init() but
event buffer allocation uses the cached copy of hwparams to determine
the number of event buffers and the caching is done in dwc3_core_init.
So moved dwc3_cache_hwparams function before dwc3_alloc_event_buffers so
that dwc3_alloc_event_buffers sees the correct number of event buffers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By always setting up the HWS register for both physical and virtual
address variations during render ring we can reduce the number of
different special cases that get set up at varying different times
during module load.
Fixes regression from
commit c630119f43
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Oct 17 11:32:57 2012 +0200
drm/i915: don't save/restore HWS_PGA reg for kms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
enable the dma support for auart0 in mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current mxs-auart driver is used for both mx23 and mx28.
But in mx23, the DMA has a bug(see errata:2836). We can not add the
DMA support in mx23, but we can add DMA support to auart in mx28.
So in order to add the DMA support for the auart in mx28, we should
distinguish the distinguish SOCs.
This patch adds a new platform_device_id table and a inline function
is_imx28_auart() to distinguish the mx23 and mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows overriding default methods serial_in/serial_out.
In such platform specific replacement it is possible to use
other regshift, biased register offset, any other manipulation
that is not covered with common default methods.
Overriding default methods may be useful for platforms which got
serial peripheral with registers represented in big endian.
In this situation and assuming that 32 bit operations / alignment
is required then it may be useful to swab words before/after
accessing the serial registers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to MT-B because Synaptics touch devices are capable
of tracking identifiable fingers.
Signed-off-by: Alexandra Chin <alexandra.chin@tw.synaptics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "i2c-s3c2410: Add HDMIPHY quirk for S3C2440" added support for
HDMIPHY with some special handling in s3c24xx_i2c_set_master:
"due to unknown reason (probably HW bug in HDMIPHY and/or the controller)
a transfer fails to finish. The controller hangs after sending the last
byte, the workaround for this bug is resetting the controller after each
transfer"
The "unknown reason" was that the proper sequence for generating a STOP
condition wasn't being followed as per the datasheet. Since this is fixed
by "PATCH: i2c-s3c2410: do not generate STOP for QUIRK_HDMIPHY buses",
remove the special handling.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Usually, the i2c controller has finished emitting the i2c STOP before the
driver reaches the bus idle polling loop. Optimize for this most common
case by reading IICSTAT first and potentially skipping the loop.
If the cpu is faster than the hardware, we wait for bus idle in a polling
loop. However, since the duration of one iteration of the loop is
dependent on cpu freq, and this i2c IP is used on many different systems,
use a time based loop timeout (5 ms).
We would like very low latencies to detect bus idle for the normal
'fast' case. However, if a device is slow to release the bus for some
reason, it could hold off the STOP generation for up to several
milliseconds. Rapidly polling for bus idle would seriously load the CPU
while waiting for it to release the bus. So, use a partial exponential
backoff as a compromise between idle detection latency and cpu load.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The datasheet says that the STOP sequence should be:
1) I2CSTAT.5 = 0 - Clear BUSY (or 'generate STOP')
2) I2CCON.4 = 0 - Clear IRQPEND
3) Wait until the stop condition takes effect.
4*) I2CSTAT.4 = 0 - Clear TXRXEN
Where, step "4*" is only for buses with the "HDMIPHY" quirk.
However, after much experimentation, it appears that:
a) normal buses automatically clear BUSY and transition from
Master->Slave when they complete generating a STOP condition.
Therefore, step (3) can be done in doxfer() by polling I2CCON.4
after starting the STOP generation here.
b) HDMIPHY bus does neither, so there is no way to do step 3.
There is no indication when this bus has finished generating STOP.
In fact, we have found that as soon as the IRQPEND bit is cleared in
step 2, the HDMIPHY bus generates the STOP condition, and then immediately
starts transferring another data byte, even though the bus is supposedly
stopped. This is presumably because the bus is still in "Master" mode,
and its BUSY bit is still set.
To avoid these extra post-STOP transactions on HDMI phy devices, we just
disable Serial Output on the bus (I2CSTAT.4 = 0) directly, instead of
first generating a proper STOP condition. This should float SDA & SCK
terminating the transfer. Subsequent transfers start with a proper START
condition, and proceed normally.
The HDMIPHY bus is an internal bus that always has exactly two devices,
the host as Master and the HDMIPHY device as the slave. Skipping the STOP
condition has been tested on this bus and works.
Also, since we disable the bus directly from the isr, we can skip the bus
idle polling loop at the end of doxfer().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We probably don't want to change I2C frequency while a transfer is in
progress. The current implementation grabs a spinlock, but that only
protected the writes to IICCON when starting a message, it didn't protect
against clock changes in the middle of a transaction.
Note: The i2c-core already grabs the adapter lock before calling
s3c24xx_i2c_doxfer(), which ensures that only one caller is issuing a
xfer at a time. This means it is not necessary to disable interrupts
(spin_lock_irqsave) when changing frequencies, since there won't be
any i2c interrupts if there is no on-going xfer.
Lastly, i2c_lock_adapter() may cause the cpufreq_transition to sleep if
if a xfer is in progress, but this is ok since cpufreq notifiers are
called in a kernel thread, and there are already cases where it could
sleep, such as when using i2c to update the output of a voltage
regulator.
Note: the cpufreq part of this change has no functional affect on
exynos, where the i2c clock is independent of the cpufreq.
But, there is a slight perfomance boost since we no longer need to
lock/unlock an additional spinlock.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
A small code saving and less error handling to worry about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use the PM_SLEEP ifdef for system suspend and resume. This is partly
in preparation for adding runtime operations and partly because a user
may in theory choose to enable runtime suspend but not system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>