Line 110 uses UL as a compiler cast for the 0x constant, but it's not
large enough to hold a 64-bit value on a 32-bit arch.
Signed-off-by: Doug Ledford <dledford@redhat.com>
[ Use "-1" instead of "FFFFFFFFFFFFFFFFULL". - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change event type to switch for the power and autopower switches.
Additionally, this patch aligns the keycodes with the other linkstation
boards already supported by linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Don't use the specific board name in a the common device tree include file.
Instead use the common name 'lsxl'.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the CACHE_FEROCEON_L2 test to kirkwood_l2_init, since linking
fails on the reference to feroceon_l2_init.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a simple driver providing platform restart and power off
functions using VE config infrastructure.
By writing to the "active" attribute of the reboot or reset device,
user can decide what if the platform is supposed to execute full power
cycle (reboot, default) or simply assert system level reset signal.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Conflicts:
include/linux/vexpress.h
Base the UART detection heuristic on architecturally defined
MIDR register instead of implementation dependent CBAR. The
only tile using the original memory map is V2P-CA9 with Cortex
A9 r0p1, which MIDR contains value 0x410fc091.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Threads in the bottom half of batadv_bla_check_bcast_duplist() might
otherwise for instance overwrite variables which other threads might
be using/reading at the same time in the top half, potentially
leading to messing up the bcast_duplist, possibly resulting in false
bridge loop avoidance duplicate check decisions.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
So far the crc16 checksum for a batman-adv broadcast data packet, received
on a batman-adv hard interface, was calculated over zero bytes of its
content leading to many incoming broadcast data packets wrongly being
dropped (60-80% packet loss).
This patch fixes this issue by calculating the crc16 over the actual,
complete broadcast payload.
The issue is a regression introduced by
("batman-adv: add broadcast duplicate check").
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The sysfs and procfs output of the instruction and data caches were
wrong: the output of the data cache provided that instruction cache
values and vice versa.
Fix this by using the correct type indication when issueing the
ecag instruction.
Reported-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Because of a change in the s390 arch backend of binutils (commit 23ecd77
"Pick the default arch depending on the target size" in binutils repo)
31 bit builds will fail since the linker would now try to create 64 bit
binary output.
Fix this by setting OUTPUT_ARCH to s390:31-bit instead of s390.
Thanks to Andreas Krebbel for figuring out the issue.
Fixes this build error:
LD init/built-in.o
s390x-4.7.2-ld: s390:31-bit architecture of input file
`arch/s390/kernel/head.o' is incompatible with s390:64-bit output
Cc: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 0x10000 entry point can be called in z/Arch architecture and 64 bit
addressing mode. Therefore this patch removes the unnecessary 31 bit
switch code from the kdump startup function.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increase the maximum number of available counters and check if
the hardware supports the counter. Support is indicated by the
version of the CPU-measurement counter facility.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Receiving cc=3 from store subchannel means 2 things:
* the subchannel is not provided
* there are no further subchannels in this subchannel set
With this patch we abort the store subchannel loop after cc=3 (or an
exception) and clear the subsequent bits in the subchannel id set.
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use generic bitmap functions in the subchannel id bitmap to
simplify and de-bloat the code.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add back a hunk from "4dcc2a4 s390/chsc: make headers usable"
which was lost during the merge of the UAPI patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on information from the ZTE Windows drivers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old pinctrl table for the SKE keypad was using all the
wrong settings and positions. Fixing it up to one that works!
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>nn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A few places touch chan->max_power based on updated tx power rules, but
forget to do the same to chan->max_reg_power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No driver initializes chan->max_antenna_gain to something sensible, and
the only place where it is being used right now is inside ath9k. This
leads to ath9k potentially using less tx power than it can use, which can
decrease performance/range in some rare cases.
Rather than going through every single driver, this patch initializes
chan->orig_mag in wiphy_register(), ignoring whatever value the driver
left in there. If a driver for some reason wishes to limit it independent
from regulatory rulesets, it can do so internally.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's the first set of fixes for v3.7-rc cycle.
DesignWare Core USB3 Driver (dwc3) got two fixes. The first one fixes a long
standing bug which would keep endpoint with BUSY flag set forever if we cancel
a transfer which has already been started by the controller. The second fix
will just switch PHYs back off when DWC3 driver is removed.
MUSB fixed a bug which would cause a Kernel Oops at least on AM3517 when
removing a device. For some reason that particular device can fall into a
situation where you have both Disconnect and Endpoint IRQs happen
simultaneously (have both bits set in IRQ_STATUS register) and, because
Disconnect Interrupt is handled before Endpoint Interrupts, we would try to
transfer data over a disconnected device, thus generating a kernel oops.
Renensas' USB DRD driver got two fixes which are a) fixing an off-by-one bug on
the pipe iterator implementation and b) fixing Interrupt Status Clear procedure
in order to properly clear a single Interrupt event without clearing (and
masking) other events we didn't handle yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IlgT
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.7-rc2
Here's the first set of fixes for v3.7-rc cycle.
DesignWare Core USB3 Driver (dwc3) got two fixes. The first one fixes a long
standing bug which would keep endpoint with BUSY flag set forever if we cancel
a transfer which has already been started by the controller. The second fix
will just switch PHYs back off when DWC3 driver is removed.
MUSB fixed a bug which would cause a Kernel Oops at least on AM3517 when
removing a device. For some reason that particular device can fall into a
situation where you have both Disconnect and Endpoint IRQs happen
simultaneously (have both bits set in IRQ_STATUS register) and, because
Disconnect Interrupt is handled before Endpoint Interrupts, we would try to
transfer data over a disconnected device, thus generating a kernel oops.
Renensas' USB DRD driver got two fixes which are a) fixing an off-by-one bug on
the pipe iterator implementation and b) fixing Interrupt Status Clear procedure
in order to properly clear a single Interrupt event without clearing (and
masking) other events we didn't handle yet.
This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.
System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port data is initialised before creating sysfs attributes to
avoid a race.
A recent patch ("USB: io_ti: fix port-data memory leak") got the
sysfs-attribute creation and port-data initialisation ordering wrong.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure sysfs attributes are created at port probe.
A recent patch ("USB: iuu_phoenix: fix port-data memory leak") removed
the sysfs-attribute creation by mistake.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #PF with PFEC.RSV = 1 indicates that the guest is accessing MMIO, we
can not fix it if it is caused by delivery event. Reporting internal error
for this case
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
VM exits during Event Delivery is really unexpected if it is not caused
by Exceptions/EPT-VIOLATION/TASK_SWITCH, we'd better to report an internal
and freeze the guest, the VMM has the chance to check the guest
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some BIOSes may forcibly suspend RC6 during their operation which
trigger a warning as we find the hardware in a perplexing state upon
first use. So far that appears to be the worst symptom as fortuituously
we use the same values as the BIOS for programming the FORCEWAKE register.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now no longer rely on this.
This is step 1 on a long journey to rid us of the save/restore
madness, which tends to lightly paper over many issues, and cause
tons of bad things itself ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: satisfy Paulo's ocd and drop the needless braces.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of relying on the register save/restore madness to do this.
To extract a bit of code call drm_mode_config_reset both on resume
and boot-up and move the hw state frobbing from the crt_init to the
->reset callback. The crt connector is the only one with a ->reset
callback, hence we can easily do this.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... since they don't apply to pre-pch platforms and could actually be
harmful.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When assigning amp_mgr in hci_conn (type AMP_LINK) get also reference.
In hci_conn_del those references would be put for both conn types
AMP_LINK and ACL_LINK associated with amp_mgr.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Instead of allocating descriptors on-the-fly for the device tree
initialization case, use irq_domain_add_simple() which will take
care of this if you pass negative as the first_irq.
Alter the signature of __vic_init() to pass the first_irq as
signed so this works as expected.
Switching the VIC to use irq_domain_add_simple() also has the
upside of displaying the same WARNING when you boot with
pre-allocated descriptors on systems using SPARSE_IRQ but
yet not using device tree.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We currently have a single function to enable and disable the manager
output for LCD and DIGIT. The functions are a bit complex, as handling
both enable and disable require some extra steps to ensure that the
output is enabled or disabled properly without errors before exiting the
function.
The code can be made simpler to understand by splitting the functions
into separate enable and disable functions. We'll also clean up the
comments and some parameter names at the same time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc.c's functions to enable LCD and DIGIT outputs can be cleaned up a
bit by using common functions to set the enable bit and to check if the
output is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() uses struct omap_overlay to get the caps for the
overlay. We can change the code to get the caps directly from dss
features, thus removing the dependency to struct omap_overlay.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_device and dss_mgr_unset_device are declared in dss.h, but
the functions do not exist. Remove the declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dispc has a bunch of functions used to configure output related
parameters:
- dispc_mgr_set_io_pad_mode
- dispc_mgr_enable_stallmode
- dispc_mgr_enable_fifohandcheck
- dispc_mgr_set_clock_div
- dispc_mgr_set_tft_data_lines
- dispc_lcd_enable_signal_polarity
- dispc_mgr_set_lcd_type_tft
These are all called together, and the configuration values are taken
from struct dss_lcd_mgr_config.
Instead of exposing those individual dispc functions, create a new one,
dispc_mgr_set_lcd_config(), which is used to configure the above
parameters from values in struct dss_lcd_mgr_config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we enable an output we don't check if we need to register the vsync
isr. This causes us to miss vsync interrupts until somebody changes the
configuration of an overlay or an overlay manager.
Add the registration to dss_mgr_enable to fix the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.
This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.
Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>
1. On ARM platform, "nohlt" can be used to prevent core from idle
process, returning immediately.
2. There are two interfaces, exported for other modules, named
"disable_hlt" and "enable_hlt" are used to enable/disable the
cpuidle mechanism by increasing/decreasing "hlt_counter".
Disable_hlt and enable_hlt are paired operation,
when you first call disable_hlt and then enable_hlt, the
semantics are right.
3. There is no obvious constraint to prevent user(driver/module)
code to prevent the case that enable_hlt is ahead of disable_hlt,
which is a fatal operation on kernel state change from user,
and there is no any WARNING or notification if the case happens
in current kernel code.
This patch aims to report BUG when the case happens, just like
what the kernel do when enable_irq is ahead of disable_irq.
Link: https://patchwork.kernel.org/patch/1527881/
Signed-off-by: fwu <fwu@marvell.com>
Signed-off-by: YiLu Mao <ylmao@marvell.com>
Signed-off-by: Ning Jiang <ning.jiang@marvell.com>
Acked-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For writes, HWFC shall be switched off when transfer size <= 8
bytes and when MCLK rate is above 50 MHz. For 50MHz and below
it shall be switched off when transfer size < 8 bytes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For data writes <= 8 bytes, HW flow control was disabled but
never re-enabled when the transfer was completed. This meant
that a following read request would give buffer overrun errors.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the
sample period of a running perf_event. Consequently, when calculating
the next event period, the new period will only be considered after the
previous one has overflowed.
This patch changes the calculation of the remaining event ticks so that
they are offset if the period has changed.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Andreas Sandberg <andreas.sandberg@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit c564df4db8 (ARM: 7540/1: kexec:
Check segment memory addresses) added a safety check with accidentally
reversed condition, and broke kexec functionality on ARM. Fix this.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because mov pc,<Rn> never switches instruction set when executed in
Thumb code, Thumb-2 kernels will silently execute the target code
after cpu_reset as Thumb code, even if the passed code pointer
denotes ARM (bit 0 clear).
This patch uses bx instead, ensuring the correct instruction set
for the target code.
Thumb code in the kernel is not supported prior to ARMv7, so other
CPUs are not affected.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>