On systems with very large memory (1 TB in our case), BIOS may report a
reserved region or a hole in the E820 map, even above the 4 GB range. Exclude
these from the direct mapping.
[ hpa: this should be done not just for > 4 GB but for everything above the legacy
region (1 MB), at the very least. That, however, turns out to require significant
restructuring. That work is well underway, but is not suitable for rc/stable. ]
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/1319145326-13902-1-git-send-email-jacob.shin@amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Why do we need to write the superblock to disk once we've written
all the data? We don't actually - the reasons for doing this are
lost in the mists of time, and go back to the way Irix used to drive
VFS flushing.
On linux, this code is only called from two contexts: remount and
.sync_fs. In the remount case, the call is followed by a metadata
sync, which unpins and writes the superblock. In the sync_fs case,
we only need to force the log to disk to ensure that the superblock
is correctly on disk, so we don't actually need to write it. Hence
the functionality is either redundant or superfluous and thus can be
removed.
Seeing as xfs_quiesce_data is essentially now just a log force,
remove it as well and fold the code back into the two callers.
Neither of them need the log covering check, either, as that is
redundant for the remount case, and unnecessary for the .sync_fs
case.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Make use of DT support for the crypto engine on dove and remove
the obsolete init call.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The watchdog on dove requires an interrupt that is not yet
available on DT. Therefore, the watchdog DT node is removed
until the corresponding chained intc is available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds proper ranges for all mapped addresses within
dove SoC and moves the interrupt controller node inside the simple-bus
node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes wrong clock names of lately added clock gates
for sata and gbe (mv64xx_eth).
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the review process of dove DT patches, Tauros2 cache
init call was changed and DT support added. This patch fixes
the call to Tauros2 init and adds a DT node. Moreover, plat/irq.h
include was missing from mach-dove/common.c.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As dove now has clock gating control ensure pcie ports grab their
clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the syncd functions moved to the log and/or removed, the syncd
workqueue is the only remaining bit left. It is used by the log
covering/ail pushing work, as well as by the inode reclaim work.
Given how cheap workqueues are these days, give the log and inode
reclaim work their own work queues and kill the syncd work queue.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't do any data writeback from XFS any more - the VFS is
completely responsible for that, including for freeze. We can
replace the remaining caller with a VFS level function that
achieves the same thing, but without conflicting with current
writeback work.
This means we can remove the flush_work and xfs_flush_inodes() - the
VFS functionality completely replaces the internal flush queue for
doing this writeback work in a separate context to avoid stack
overruns.
This does have one complication - it cannot be called with page
locks held. Hence move the flushing of delalloc space when ENOSPC
occurs back up into xfs_file_aio_buffered_write when we don't hold
any locks that will stall writeback.
Unfortunately, writeback_inodes_sb_if_idle() is not sufficient to
trigger delalloc conversion fast enough to prevent spurious ENOSPC
whent here are hundreds of writers, thousands of small files and GBs
of free RAM. Hence we need to use sync_sb_inodes() to block callers
while we wait for writeback like the previous xfs_flush_inodes
implementation did.
That means we have to hold the s_umount lock here, but because this
call can nest inside i_mutex (the parent directory in the create
case, held by the VFS), we have to use down_read_trylock() to avoid
potential deadlocks. In practice, this trylock will succeed on
almost every attempt as unmount/remount type operations are
exceedingly rare.
Note: we always need to pass a count of zero to
generic_file_buffered_write() as the previously written byte count.
We only do this by accident before this patch by the virtue of ret
always being zero when there are no errors. Make this explicit
rather than needing to specifically zero ret in the ENOSPC retry
case.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
When unmounting the filesystem, there are lots of operations that
need to be done in a specific order, and they are spread across
across a couple of functions. We have to drain the AIL before we
write the unmount record, and we have to shut down the background
log work before we do either of them.
But this is all split haphazardly across xfs_unmountfs() and
xfs_log_unmount(). Move all the AIL flushing and log manipulations
to xfs_log_unmount() so that the responisbilities of each function
is clear and the operations they perform obvious.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The commit 5395a04841 ("perf hists: Separate overhead and baseline
columns") makes the "Overhead" column no more the first one, this
caused the test that checks if it is time to show if a histogram
entry has callchains never hits.
Fix it by checking if the 'i' variable is equal to PERF_HPP__OVERHEAD
instead of 0.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-w3lcbx0fx1fnh3l2cbq40q2e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The only thing the periodic sync work does now is flush the AIL and
idle the log. These are really functions of the log code, so move
the work to xfs_log.c and rename it appropriately.
The only wart that this leaves behind is the xfssyncd_centisecs
sysctl, otherwise the xfssyncd is dead. Clean up any comments that
related to xfssyncd to reflect it's passing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
If the filesystem is mounted or remounted read-only, stop the sync
worker that tries to flush or cover the log if the filesystem is
dirty. It's read-only, so it isn't dirty. Restart it on a remount,rw
as necessary. This avoids the need for RO checks in the work.
Similarly, stop the sync work when the filesystem is frozen, and
start it again when the filesysetm is thawed. This avoids the need
for special freeze checks in the work.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of starting and stopping background work on the xfs_mount_wq
all at the same time, separate them to where they really are needed
to start and stop.
The xfs_sync_worker, only needs to be started after all the mount
processing has completed successfully, while it needs to be stopped
before the log is unmounted.
The xfs_reclaim_worker is started on demand, and can be
stopped before the unmount process does it's own inode reclaim pass.
The xfs_flush_inodes work is run on demand, and so we really only
need to ensure that it has stopped running before we start
processing an unmount, freeze or remount,ro.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Add chip details for E-mu 1010 PCIe card. It has the same
chip as found in E-mu 1010b but it uses different PCI id.
Signed-off-by: Maxim Kachur <mcdebugger@duganet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
xfs_syncd_start and xfs_syncd_stop tie a bunch of unrelated
functionailty together that actually have different start and stop
requirements. Kill these functions and open code the start/stop
methods for each of the background functions.
Subsequent patches will move the start/stop functions around to the
correct places to avoid races and shutdown issues.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Currently, if the GPMC driver fails to reserve memory when probed we will
call BUG() and the kernel will not boot. Instead of calling BUG(), return
an error from probe and allow kernel to boot.
Boot tested on AM335x beagle bone board and OMAP4430 Panda board.
V2 changes:
- Ensure that clock and memory resources are released on error.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the code only acquired spinlock after increasing / decreasing
the usecount value, which is wrong. This leaves a small window where
a task switch may occur between the check of the usecount and the actual
wakeup / sleep of the domain. Fixed by moving the spinlock locking before
the usecount access. Left the usecount as atomic_t if someone wants an
easy access to the parameter through atomic_read.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
tcu sysfs attr was used to only control calibration process so far. Direct
sensor register access possibility has been revealed. Allowing readout of tcu
permits usage of this feature.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
From Simon Horman:
"Please consider the following fix for the KZM-A9-GT board for 3.7.
They both resolve fallout from recent IOMEM() changes."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: use __iomem pointers for MMIO
ARM: shmobile: armadillo800eva: __io abuse cleanup
More UAPI stuff.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20121017.010656.383828471689899431.davem@davemloft.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The evsel methods to read tracepoint fields uses libtraceevent
functions, becoming needed by the python binding as well.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-j3o4v7jyvp9ke9n230l96a1m@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The commit 0c1fe6b:
'perf tools: Have the page size value available for all tools'
Broke the python binding because the global variable 'page_size' is
initialized on the main() routine, that is not called when using
just the python binding, causing evlist.mmap() to fail because it
expects that variable to be initialized to the system's page size.
Fix it by initializing it on the binding init routine.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-vrvp3azmbfzexnpmkhmvtzzc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The only difference between FNAME(update_pte) and FNAME(pte_prefetch)
is that the former is allowed to prefetch gfn from dirty logged slot,
so introduce a common function to prefetch spte
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The function does not depend on guest mmu mode, move it out from
paging_tmpl.h
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Let it return emulate state instead of spte like __direct_map
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Remove mmu_is_invalid and use is_invalid_pfn instead
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently when 'range->start' is beyond the end of file system
nothing is done and that fact is ignored, where in fact we should return
EINVAL. The same problem is when 'range.len' is smaller than file system
block.
Fix this by adding check for such conditions and return EINVAL
appropriately.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Tino Reichardt <milky-kernel@mcmilk.de>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
If the filehandle is stale, or open access is denied for some reason,
nlm_fopen() may return one of the NLMv4-specific error codes nlm4_stale_fh
or nlm4_failed. These get passed right through nlm_lookup_file(),
and so when nlmsvc_retrieve_args() calls the latter, it needs to filter
the result through the cast_status() machinery.
Failure to do so, will trigger the BUG_ON() in encode_nlm_stat...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Reported-by: Larry McVoy <lm@bitmover.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch DAPMises headphone and lineout output enable controls.
Earlier these output enable bits were permanently turned on in probe.
In da9055 codec, right outmixer is directly connected with right HP and
Line out. This resulted in two side effects,
(1) When you only want to use lineout, right HP (and connected charge
pump) also gets enabled
(2) When you only want to use stereo HP, lineout also gets enabled
This patch adds three switches to select which output(s) should be
enabled.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts the arm64 port to use the generic sys_execve()
implementation removing the arm64-specific (compat_)sys_execve_wrapper()
functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch enables CONFIG_GENERIC_KERNEL_EXECVE on arm64 and removes the
arm64-specific implementation of kernel_execve().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch enables CONFIG_GENERIC_KERNEL_THREAD on arm64, changes
copy_threads to cope with kernel threads creation and adapts
ret_from_fork accordingly. The arm64-specific kernel_thread
implementation is no longer needed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Here we provide the GPIO Regulator driver with Device Tree capability, so
that when a platform is booting with DT instead of platform data we can
still make full use of it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s3c2440_clk_add is a subsys_interface method and calls clkdev_add_table,
which is marked as __init. The modpost script complains about this
because we must not call an __init function from a function in the .text
section, and we cannot reference an __init function from a subsys_interface
pointer.
I have verified that the only code path into s3c2440_clk_add() is
from "int __init s3c2440_init(void)", so s3c2440_clk_add can be marked
__init_refok instead.
Without this patch, building mini2440_defconfig results in:
WARNING: vmlinux.o(.text+0x9848): Section mismatch in reference from the function s3c2440_clk_add() to the function .init.text:clkdev_add_table()
The function s3c2440_clk_add() references
the function __init clkdev_add_table().
This is often because s3c2440_clk_add lacks a __init
annotation or the annotation of clkdev_add_table is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Ben Dooks <ben-linux@fluff.org>
There is a subtle difference between dma_transfer_direction and
dma_data_direction: the former is used by the dmaengine framework,
while the latter is used by the dma-mapping API. Although the
purpose is comparable, the actual values are different and must
not be mixed. In this case, the driver just wants to use
dma_transfer_direction.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_spi_dmacb':
drivers/spi/spi-s3c64xx.c:239:21: warning: comparison between
'enum dma_data_direction' and 'enum dma_transfer_direction' [-Wenum-compare]
As pointed out by Kukjin Kim, this also changes the use of constants
from DMA_FROM_DEVICE/DMA_TO_DEVICE to DMA_DEV_TO_MEM/DMA_MEM_TO_DEV.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
The TPS65090's DCDC output can also be enable/disable through the
external digital input signal. Add support for enable/disable
either through register access via I2C or through external
control inputs. The external control inputs can be driven through
GPIOs also and hence adding support for passing the GPIO number.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TPS65090 supports the two LDOs, LDO1 and LDO2. These are
always ON regulators. The output on these LDOs are available
once the input voltage available for these LDOs.
Add support for these LDOs regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make the names proper and more appropriate:
Rename the driver name from tps65090-regulator to tps65090-pmic.
Rename the regulators from TPS65090_ID_* to TPS65090_REGULATOR_*
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>