- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
* pci/controller/loongson:
PCI/ACPI: Increase Loongson max PCI hosts to 8
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups without
having to stomp on the core's pdev->dev.groups (Lukas Wunner)
* pci/sysfs:
s390/pci: Stop usurping pdev->dev.groups
- Wait for each level of downstream bus, not just the first, to become
accessible before restoring devices on that bus (Ilpo Järvinen)
* pci/reset:
PCI: Wait for Link before restoring Downstream Buses
- Initialize leds class earlier (with an unfortunate Makefile ordering
change) so the PCI NPEM driver can use it (Mariusz Tkaczyk)
- Add Native PCIe Enclosure Management (NPEM) support for sysfs control of
NVMe RAID storage indicators (ok/fail/locate/rebuild/etc) (Mariusz
Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which is
functionally similar to NPEM but mediated by platform firmware (Mariusz
Tkaczyk)
* pci/npem:
PCI/NPEM: Add _DSM PCIe SSD status LED management
PCI/NPEM: Add Native PCIe Enclosure Management support
leds: Init leds class earlier
- Add function 0 DMA alias quirk for Glenfly Arise audio function, which
uses the function 0 Requester ID (WangYuli)
* pci/iommu:
PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
- Clear LBMS bit after a manual link retrain so we don't try to retrain a
link when there's no downstream device anymore (Maciej W. Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance to use
higher speeds (Maciej W. Rozycki)
- Correct interpretation of pcie_retrain_link() return status and update it
to return 0/errno instead of true/false (Maciej W. Rozycki)
* pci/enumeration:
PCI: Use an error code with PCIe failed link retraining
PCI: Correct error reporting with PCIe failed link retraining
PCI: Revert to the original speed after PCIe failed link retraining
PCI: Clear the LBMS bit after a link retrain
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions() (Philipp
Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp Stanner)
* pci/devres:
drm/ast: Request PCI BAR with devres
PCI: Deprecate pcim_iomap_regions() in favor of pcim_iomap_region()
drm/vboxvideo: Add PCI region request
PCI: Make pcim_request_region() a public function
- Wait for device readiness after reset by polling Vendor ID and looking
for Configuration RRS instead of polling the Command register and looking
for non-error completions (Bjorn Helgaas)
- Fix an aardvark issue with emulating Configuration RRS for two-byte reads
of Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
- Rename CRS Completion Status to RRS to match spec usage (Bjorn Helgaas)
* pci/crs:
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
If some part of the kernel adds task_work that needs executing, in terms
of signaling it'll generally use TWA_SIGNAL or TWA_RESUME. Those two
directly translate to TIF_NOTIFY_SIGNAL or TIF_NOTIFY_RESUME, and can
be used for a variety of use case outside of task_work.
However, io_cqring_wait_schedule() only tests explicitly for
TIF_NOTIFY_SIGNAL. This means it can miss if task_work got added for
the task, but used a different kind of signaling mechanism (or none at
all). Normally this doesn't matter as any task_work will be run once
the task exits to userspace, except if:
1) The ring is setup with DEFER_TASKRUN
2) The local work item may generate normal task_work
For condition 2, this can happen when closing a file and it's the final
put of that file, for example. This can cause stalls where a task is
waiting to make progress inside io_cqring_wait(), but there's nothing else
that will wake it up. Hence change the "should we schedule or loop around"
check to check for the presence of task_work explicitly, rather than just
TIF_NOTIFY_SIGNAL as the mechanism. While in there, also change the
ordering of what type of task_work first in terms of ordering, to both
make it consistent with other task_work runs in io_uring, but also to
better handle the case of defer task_work generating normal task_work,
like in the above example.
Reported-by: Jan Hendrik Farr <kernel@jfarr.cc>
Link: https://github.com/axboe/liburing/issues/1235
Cc: stable@vger.kernel.org
Fixes: 846072f16e ("io_uring: mimimise io_cqring_wait_schedule")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Changes cs35l45_get_clk_freq_id() function data type from unsigned int
to int. This function is returns a positive index value if successful
or a negative error code if unsuccessful.
Functionally there should be no difference as long as the unsigned int
return is interpreted as an int, however it should be corrected for
readability.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Link: https://patch.msgid.link/20240919151654.197337-1-rriveram@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Implement the SCHED_DEADLINE server infrastructure - Daniel Bristot de Oliveira's
last major contribution to the kernel:
"SCHED_DEADLINE servers can help fixing starvation issues of low priority
tasks (e.g., SCHED_OTHER) when higher priority tasks monopolize CPU
cycles. Today we have RT Throttling; DEADLINE servers should be able to
replace and improve that."
(Daniel Bristot de Oliveira, Peter Zijlstra, Joel Fernandes,
Youssef Esmat, Huang Shijie)
- Preparatory changes for sched_ext integration:
- Use set_next_task(.first) where required
- Fix up set_next_task() implementations
- Clean up DL server vs. core sched
- Split up put_prev_task_balance()
- Rework pick_next_task()
- Combine the last put_prev_task() and the first set_next_task()
- Rework dl_server
- Add put_prev_task(.next)
(Peter Zijlstra, with a fix by Tejun Heo)
- Complete the EEVDF transition and refine EEVDF scheduling:
- Implement delayed dequeue
- Allow shorter slices to wakeup-preempt
- Use sched_attr::sched_runtime to set request/slice suggestion
- Document the new feature flags
- Remove unused and duplicate-functionality fields
- Simplify & unify pick_next_task_fair()
- Misc debuggability enhancements
(Peter Zijlstra, with fixes/cleanups by Dietmar Eggemann,
Valentin Schneider and Chuyi Zhou)
- Initialize the vruntime of a new task when it is first enqueued,
resulting in significant decrease in latency of newly woken tasks.
(Zhang Qiao)
- Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
(K Prateek Nayak, Peter Zijlstra)
- Clean up and clarify the usage of Clean up usage of rt_task()
(Qais Yousef)
- Preempt SCHED_IDLE entities in strict cgroup hierarchies
(Tianchen Ding)
- Clarify the documentation of time units for deadline scheduler
parameters. (Christian Loehle)
- Remove the HZ_BW chicken-bit feature flag introduced a year ago,
the original change seems to be working fine.
(Phil Auld)
- Misc fixes and cleanups (Chen Yu, Dan Carpenter, Huang Shijie,
Peilin He, Qais Yousefm and Vincent Guittot)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=TEC6
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2024-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Implement the SCHED_DEADLINE server infrastructure - Daniel Bristot
de Oliveira's last major contribution to the kernel:
"SCHED_DEADLINE servers can help fixing starvation issues of low
priority tasks (e.g., SCHED_OTHER) when higher priority tasks
monopolize CPU cycles. Today we have RT Throttling; DEADLINE
servers should be able to replace and improve that."
(Daniel Bristot de Oliveira, Peter Zijlstra, Joel Fernandes, Youssef
Esmat, Huang Shijie)
- Preparatory changes for sched_ext integration:
- Use set_next_task(.first) where required
- Fix up set_next_task() implementations
- Clean up DL server vs. core sched
- Split up put_prev_task_balance()
- Rework pick_next_task()
- Combine the last put_prev_task() and the first set_next_task()
- Rework dl_server
- Add put_prev_task(.next)
(Peter Zijlstra, with a fix by Tejun Heo)
- Complete the EEVDF transition and refine EEVDF scheduling:
- Implement delayed dequeue
- Allow shorter slices to wakeup-preempt
- Use sched_attr::sched_runtime to set request/slice suggestion
- Document the new feature flags
- Remove unused and duplicate-functionality fields
- Simplify & unify pick_next_task_fair()
- Misc debuggability enhancements
(Peter Zijlstra, with fixes/cleanups by Dietmar Eggemann, Valentin
Schneider and Chuyi Zhou)
- Initialize the vruntime of a new task when it is first enqueued,
resulting in significant decrease in latency of newly woken tasks
(Zhang Qiao)
- Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
(K Prateek Nayak, Peter Zijlstra)
- Clean up and clarify the usage of Clean up usage of rt_task()
(Qais Yousef)
- Preempt SCHED_IDLE entities in strict cgroup hierarchies
(Tianchen Ding)
- Clarify the documentation of time units for deadline scheduler
parameters (Christian Loehle)
- Remove the HZ_BW chicken-bit feature flag introduced a year ago,
the original change seems to be working fine (Phil Auld)
- Misc fixes and cleanups (Chen Yu, Dan Carpenter, Huang Shijie,
Peilin He, Qais Yousefm and Vincent Guittot)
* tag 'sched-core-2024-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
sched/cpufreq: Use NSEC_PER_MSEC for deadline task
cpufreq/cppc: Use NSEC_PER_MSEC for deadline task
sched/deadline: Clarify nanoseconds in uapi
sched/deadline: Convert schedtool example to chrt
sched/debug: Fix the runnable tasks output
sched: Fix sched_delayed vs sched_core
kernel/sched: Fix util_est accounting for DELAY_DEQUEUE
kthread: Fix task state in kthread worker if being frozen
sched/pelt: Use rq_clock_task() for hw_pressure
sched/fair: Move effective_cpu_util() and effective_cpu_util() in fair.c
sched/core: Introduce SM_IDLE and an idle re-entry fast-path in __schedule()
sched: Add put_prev_task(.next)
sched: Rework dl_server
sched: Combine the last put_prev_task() and the first set_next_task()
sched: Rework pick_next_task()
sched: Split up put_prev_task_balance()
sched: Clean up DL server vs core sched
sched: Fixup set_next_task() implementations
sched: Use set_next_task(.first) where required
sched/fair: Properly deactivate sched_delayed task upon class change
...
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove.
Fixes: 6fd9c53f71 ("net: seeq: Convert timers to use timer_setup()")
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Link: https://patch.msgid.link/20240915144045.451-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- rcu pointer assignment in smk_set_cipso
- indentation in smack_ip_output
-----BEGIN PGP SIGNATURE-----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=V/iJ
-----END PGP SIGNATURE-----
Merge tag 'Smack-for-6.12' of https://github.com/cschaufler/smack-next
Pull smack updates from Casey Schaufler:
"Two patches: one is a simple indentation correction, the other
corrects a potentially rcu unsafe pointer assignment"
* tag 'Smack-for-6.12' of https://github.com/cschaufler/smack-next:
smackfs: Use rcu_assign_pointer() to ensure safe assignment in smk_set_cipso
security: smack: Fix indentation in smack_netfilter.c
The variable 'kc' is handled in the function
soc_tplg_control_dbytes_create(), and 'kc->private_value'
is assigned to 'sbe', so In the function soc_tplg_dbytes_create(),
the right 'sbe' should be 'kc.private_value', the same logical error
in the function soc_tplg_dmixer_create(), thus fix them.
Fixes: 0867278200 ("ASoC: topology: Unify code for creating standalone and widget bytes control")
Fixes: 4654ca7cc8 ("ASoC: topology: Unify code for creating standalone and widget mixer control")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://patch.msgid.link/20240914081608.3514-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
axienet_free_tx_chain returns the number of DMA descriptors it's
handled. However, axienet_tx_poll treats the return as the number of
packets. When scatter-gather SKBs are enabled, a single packet may use
multiple DMA descriptors, which causes incorrect packet counts. Fix this
by explicitly keepting track of the number of packets processed as
separate from the DMA descriptors.
Budget does not affect the number of Tx completions we can process for
NAPI, so we use the ring size as the limit instead of budget. As we no
longer return the number of descriptors processed to axienet_tx_poll, we
now update tx_bd_ci in axienet_free_tx_chain.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20240913145156.2283067-1-sean.anderson@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As advised by Documentation/networking/napi.rst, masking IRQs after
calling napi_schedule can be racy. Avoid this by only masking/scheduling
if napi_schedule_prep returns true.
Fixes: 9e2bc267e7 ("net: axienet: Use NAPI for TX completion path")
Fixes: cc37610caa ("net: axienet: implement NAPI and GRO receive")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240913145711.2284295-1-sean.anderson@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
These are only fixes originally meant for 6.11 final. Because of serious
travel problems, I could not send them in time and so this is my first
PR for 6.12.
The Aspeed driver tracks the controller's state (stop, pending,
start, etc.). Previously, when the stop command was sent, the
state was not updated. The fix in this pull request ensures the
driver's state is aligned with the device status.
The Intel SCH driver receives a new look, and among the cleanups,
there is a fix where, due to an oversight, an if/else statement
was missing the else, causing it to move forward instead of
exiting the function in case of an error.
The Qualcomm GENI I2C driver adds the IRQF_NO_AUTOEN flag to the
IRQ setup to prevent unwanted interrupts during probe.
The Xilinx XPS controller fixes TX FIFO handling to avoid missed
NAKs. Another fix ensures the controller is reinitialized when
the bus appears busy.
-----BEGIN PGP SIGNATURE-----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=KRVy
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.11-final-but-missed-it' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The Aspeed driver tracks the controller's state (stop, pending, start,
etc.). Previously, when the stop command was sent, the state was not
updated. The fix ensures the driver's state is aligned with the device
status.
The Intel SCH driver receives a new look, and among the cleanups,
there is a fix where, due to an oversight, an if/else statement was
missing the else, causing it to move forward instead of exiting the
function in case of an error.
The Qualcomm GENI I2C driver adds the IRQF_NO_AUTOEN flag to the IRQ
setup to prevent unwanted interrupts during probe.
The Xilinx XPS controller fixes TX FIFO handling to avoid missed NAKs.
Another fix ensures the controller is reinitialized when the bus
appears busy"
* tag 'i2c-for-6.11-final-but-missed-it' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: qcom-geni: Use IRQF_NO_AUTOEN flag in request_irq()
i2c: isch: Add missed 'else'
i2c: xiic: Try re-initialization on bus busy timeout
i2c: xiic: Wait for TX empty to avoid missed TX NAKs
i2c: aspeed: Update the stop sw state when the bus recovery occurs
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 4a2f83b7f7 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906023956.1004440-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The author of the blamed commit apparently did not notice something
about aqr_wait_reset_complete(): it polls the exact same register -
MDIO_MMD_VEND1:VEND1_GLOBAL_FW_ID - as aqr_firmware_load().
Thus, the entire logic after the introduction of aqr_wait_reset_complete() is
now completely side-stepped, because if aqr_wait_reset_complete()
succeeds, MDIO_MMD_VEND1:VEND1_GLOBAL_FW_ID could have only been a
non-zero value. The handling of the case where the register reads as 0
is dead code, due to the previous -ETIMEDOUT having stopped execution
and returning a fatal error to the caller. We never attempt to load
new firmware if no firmware is present.
Based on static code analysis, I guess we should simply introduce a
switch/case statement based on the return code from aqr_wait_reset_complete(),
to determine whether to load firmware or not. I am not intending to
change the procedure through which the driver determines whether to load
firmware or not, as I am unaware of alternative possibilities.
At the same time, Russell King suggests that if aqr_wait_reset_complete()
is expected to return -ETIMEDOUT as part of normal operation and not
just catastrophic failure, the use of phy_read_mmd_poll_timeout() is
improper, since that has an embedded print inside. Just open-code a
call to read_poll_timeout() to avoid printing -ETIMEDOUT, but continue
printing actual read errors from the MDIO bus.
Fixes: ad649a1fac ("net: phy: aquantia: wait for FW reset before checking the vendor ID")
Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/8ac00a45-ac61-41b4-9f74-d18157b8b6bf@nvidia.com/
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Closes: https://lore.kernel.org/netdev/c7c1a3ae-be97-4929-8d89-04c8aa870209@gmx.net/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Link: https://patch.msgid.link/20240913121230.2620122-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Four fixes for longstanding ocfs2 issues and the remainder address random
MM things.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZuvTyAAKCRDdBJ7gKXxA
jrc4AP95yg/8E50PLyVKFIsot3Vaodq908cz2vvS0n0915NO7AD+Psy11a2aR1E5
L/ZND8Zyv06qmz73WJ7BUIx0CHCniw4=
=eX0p
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2024-09-19-00-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"12 hotfixes, 11 of which are cc:stable.
Four fixes for longstanding ocfs2 issues and the remainder address
random MM things"
* tag 'mm-hotfixes-stable-2024-09-19-00-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/madvise: process_madvise() drop capability check if same mm
mm/huge_memory: ensure huge_zero_folio won't have large_rmappable flag set
mm/hugetlb.c: fix UAF of vma in hugetlb fault pathway
mm: change vmf_anon_prepare() to __vmf_anon_prepare()
resource: fix region_intersects() vs add_memory_driver_managed()
zsmalloc: use unique zsmalloc caches names
mm/damon/vaddr: protect vma traversal in __damon_va_thre_regions() with rcu read lock
mm: vmscan.c: fix OOM on swap stress test
ocfs2: cancel dqi_sync_work before freeing oinfo
ocfs2: fix possible null-ptr-deref in ocfs2_set_buffer_uptodate
ocfs2: remove unreasonable unlock in ocfs2_read_blocks
ocfs2: fix null-ptr-deref when journal load failed.
Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr). There are no user visible core changes and a whole series of
minor updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZuvd5yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishV7dAQC+TSlv
BeNm8W4yAFCXLCwnJh8rT6ZzuBsjsIHH1DPP3wD+IXuIOFf5gVRJGpCNJc/dI082
/ehSrIdeJxwaNoOOt+Y=
=SXZD
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr).
There are no user visible core changes and a whole series of minor
updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (86 commits)
scsi: smartpqi: update driver version to 2.1.30-031
scsi: smartpqi: fix volume size updates
scsi: smartpqi: fix rare system hang during LUN reset
scsi: smartpqi: add new controller PCI IDs
scsi: smartpqi: add counter for parity write stream requests
scsi: smartpqi: correct stream detection
scsi: smartpqi: Add fw log to kdump
scsi: bnx2fc: Remove some unused fields in struct bnx2fc_rport
scsi: qla2xxx: Remove the unused 'del_list_entry' field in struct fc_port
scsi: ufs: core: Remove ufshcd_urgent_bkops()
scsi: core: Remove obsoleted declaration for scsi_driverbyte_string()
scsi: bnx2i: Remove unused declarations
scsi: core: Simplify an alloc_workqueue() invocation
scsi: ufs: Simplify alloc*_workqueue() invocation
scsi: stex: Simplify an alloc_ordered_workqueue() invocation
scsi: scsi_transport_fc: Simplify alloc_workqueue() invocations
scsi: snic: Simplify alloc_workqueue() invocations
scsi: qedi: Simplify an alloc_workqueue() invocation
scsi: qedf: Simplify alloc_workqueue() invocations
scsi: myrs: Simplify an alloc_ordered_workqueue() invocation
...
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed,
Christoph Hellwig)
-----BEGIN PGP SIGNATURE-----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=DZVc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed, Christoph
Hellwig)
* tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reflow dma_supported
dma-mapping: reliably inform about DMA support for IOMMU
dma-mapping: add tracing for dma-mapping API calls
dma-mapping: use IOMMU DMA calls for common alloc/free page calls
dma-direct: optimize page freeing when it is not addressable
dma-mapping: clearly mark DMA ops as an architecture feature
vdpa_sim: don't select DMA_OPS
arm64: mm: keep low RAM dma zone
dma-mapping: don't return errors from dma_set_max_seg_size
dma-mapping: don't return errors from dma_set_seg_boundary
dma-mapping: don't return errors from dma_set_min_align_mask
scsi: check that busses support the DMA API before setting dma parameters
arm64: mm: fix DMA zone when dma-ranges is missing
dma-mapping: direct calls for dma-iommu
dma-mapping: call ->unmap_page and ->unmap_sg unconditionally
arm64: support DMA zone above 4GB
dma-mapping: replace zone_dma_bits by zone_dma_limit
dma-mapping: use bit masking to check VM_DMA_COHERENT
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler;
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp: add support for BOE NE140WUM-N6G; revert support for
SDC ATNA45AF01
- visionox-vtdr6130: improve error handling; use
devm_regulator_bulk_get_const()
- boe-th101mb31ig002: Support for starry-er88577 MIPI-DSI panel plus
DT; Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1,
BOE NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da: Support Melfas lmfbx101117480 MIPI-DSI panel plus DT; Refactor
for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
support Innolux G070ACE-LH3 plus DT bindings
support On Tat Industrial Company KD50G21-40NT-A1 plus DT bindings
- st7701:
decouple DSI and DRM code
add SPI support
support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop: Support RGB display on Rockchip RK3066; Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc: Fix transparency after disabling plane; Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset
-----BEGIN PGP SIGNATURE-----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=7jR+
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"This adds a couple of patches outside the drm core, all should be
acked appropriately, the string and pstore ones are the main ones that
come to mind.
Otherwise it's the usual drivers, xe is getting enabled by default on
some new hardware, we've changed the device number handling to allow
more devices, and we added some optional rust code to create QR codes
in the panic handler, an idea first suggested I think 10 years ago :-)
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler:
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp:
- add support for BOE NE140WUM-N6G
- revert support for SDC ATNA45AF01
- visionox-vtdr6130:
- improve error handling
- use devm_regulator_bulk_get_const()
- boe-th101mb31ig002:
- Support for starry-er88577 MIPI-DSI panel plus DT
- Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1, BOE
NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da:
- Support Melfas lmfbx101117480 MIPI-DSI panel plus DT
- Refactor for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
- support Innolux G070ACE-LH3 plus DT bindings
- support On Tat Industrial Company KD50G21-40NT-A1 plus DT
bindings
- st7701:
- decouple DSI and DRM code
- add SPI support
- support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop:
- Support RGB display on Rockchip RK3066
- Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc:
- Fix transparency after disabling plane
- Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset"
* tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel: (1326 commits)
drm/xe: Fix missing conversion to xe_display_pm_runtime_resume
drm/xe/xe2hpg: Add Wa_15016589081
drm/xe: Don't keep stale pointer to bo->ggtt_node
drm/xe: fix missing 'xe_vm_put'
drm/xe: fix build warning with CONFIG_PM=n
drm/xe: Suppress missing outer rpm protection warning
drm/xe: prevent potential UAF in pf_provision_vf_ggtt()
drm/amd/display: Add all planes on CRTC to state for overlay cursor
drm/i915/bios: fix printk format width
drm/i915/display: Fix BMG CCS modifiers
drm/amdgpu: get rid of bogus includes of fdtable.h
drm/amdkfd: CRIU fixes
drm/amdgpu: fix a race in kfd_mem_export_dmabuf()
drm: new helper: drm_gem_prime_handle_to_dmabuf()
drm/amdgpu/atomfirmware: Silence UBSAN warning
drm/amdgpu: Fix kdoc entry in 'amdgpu_vm_cpu_prepare'
drm/amd/amdgpu: apply command submission parser for JPEG v1
drm/amd/amdgpu: apply command submission parser for JPEG v2+
drm/amd/pm: fix the pp_dpm_pcie issue on smu v14.0.2/3
drm/amd/pm: update the features set on smu v14.0.2/3
...
Samuel Holland <samuel.holland@sifive.com> says:
This series fixes two areas where uninstrumented assembly routines
caused gaps in KASAN coverage on RISC-V, which were caught by KUnit
tests. The KASAN KUnit test suite passes after applying this series.
This series fixes the following test failures:
# kasan_strings: EXPECTATION FAILED at mm/kasan/kasan_test.c:1520
KASAN failure expected in "kasan_int_result = strcmp(ptr, "2")", but none occurred
# kasan_strings: EXPECTATION FAILED at mm/kasan/kasan_test.c:1524
KASAN failure expected in "kasan_int_result = strlen(ptr)", but none occurred
not ok 60 kasan_strings
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1531
KASAN failure expected in "set_bit(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1533
KASAN failure expected in "clear_bit(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1535
KASAN failure expected in "clear_bit_unlock(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1536
KASAN failure expected in "__clear_bit_unlock(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1537
KASAN failure expected in "change_bit(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1543
KASAN failure expected in "test_and_set_bit(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1545
KASAN failure expected in "test_and_set_bit_lock(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1546
KASAN failure expected in "test_and_clear_bit(nr, addr)", but none occurred
# kasan_bitops_generic: EXPECTATION FAILED at mm/kasan/kasan_test.c:1548
KASAN failure expected in "test_and_change_bit(nr, addr)", but none occurred
not ok 61 kasan_bitops_generic
Samuel Holland (2):
riscv: Omit optimized string routines when using KASAN
riscv: Enable bitops instrumentation
arch/riscv/include/asm/bitops.h | 43 ++++++++++++++++++---------------
arch/riscv/include/asm/string.h | 2 ++
arch/riscv/kernel/riscv_ksyms.c | 3 ---
arch/riscv/lib/Makefile | 2 ++
arch/riscv/lib/strcmp.S | 1 +
arch/riscv/lib/strlen.S | 1 +
arch/riscv/lib/strncmp.S | 1 +
arch/riscv/purgatory/Makefile | 2 ++
8 files changed, 32 insertions(+), 23 deletions(-)
* b4-shazam-merge:
riscv: Enable bitops instrumentation
riscv: Omit optimized string routines when using KASAN
Link: https://lore.kernel.org/r/20240801033725.28816-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The remap_file_pages syscall handler calls do_mmap() directly, which
doesn't contain the LSM security check. And if the process has called
personality(READ_IMPLIES_EXEC) before and remap_file_pages() is called for
RW pages, this will actually result in remapping the pages to RWX,
bypassing a W^X policy enforced by SELinux.
So we should check prot by security_mmap_file LSM hook in the
remap_file_pages syscall handler before do_mmap() is called. Otherwise, it
potentially permits an attacker to bypass a W^X policy enforced by
SELinux.
The bypass is similar to CVE-2016-10044, which bypass the same thing via
AIO and can be found in [1].
The PoC:
$ cat > test.c
int main(void) {
size_t pagesz = sysconf(_SC_PAGE_SIZE);
int mfd = syscall(SYS_memfd_create, "test", 0);
const char *buf = mmap(NULL, 4 * pagesz, PROT_READ | PROT_WRITE,
MAP_SHARED, mfd, 0);
unsigned int old = syscall(SYS_personality, 0xffffffff);
syscall(SYS_personality, READ_IMPLIES_EXEC | old);
syscall(SYS_remap_file_pages, buf, pagesz, 0, 2, 0);
syscall(SYS_personality, old);
// show the RWX page exists even if W^X policy is enforced
int fd = open("/proc/self/maps", O_RDONLY);
unsigned char buf2[1024];
while (1) {
int ret = read(fd, buf2, 1024);
if (ret <= 0) break;
write(1, buf2, ret);
}
close(fd);
}
$ gcc test.c -o test
$ ./test | grep rwx
7f1836c34000-7f1836c35000 rwxs 00002000 00:01 2050 /memfd:test (deleted)
Link: https://project-zero.issues.chromium.org/issues/42452389 [1]
Cc: stable@vger.kernel.org
Signed-off-by: Shu Han <ebpqwerty472123@gmail.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
[PM: subject line tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
