Merge series from srinivas.kandagatla@linaro.org:
Existing way of allocating soundwire master ports on Qualcommm platforms is
dynamic, and in linear order starting from 1 to MAX_PORTS.
This will work as long as soundwire device ports are 1:1 mapped
linearly. However on most Qcom SoCs like SM8550, SM8650, x1e80100, these
are NOT mapped in that order.
The result of this is that only one speaker among the pair of speakers
is always silent, With recent changes for WSA codec to support codec
versions and along with these patches we are able to get all speakers
working on these SoCs.
RX DCK stands for receiver DC calibration. With this calibration, we have
proper DC offset to reflect correct received signal strength indicator.
Do this calibration when bringing up interface and going to connect.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-3-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration once we are going to an AP. During
scanning phase, without this calibration RF performance is still
acceptable because it transmits and receives with low data rate at
this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-2-pkshih@realtek.com
Calculate a TX power constraint based on content of ieee80211 Transmit
Power Envelope (TPE). Since HW control registers aren't designed as many
as all kinds of TPE fields, we strictly intersect all TPE inputs in driver.
Then, according to result, constrain TX power via TX power limit/limit_RU.
Besides, extend dbgfs txpwr_table to show info about 6 GHz regulatory.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023237.7901-1-pkshih@realtek.com
Add additional policy option to let Bluetooth audio can play well
during Wi-Fi is hardware scanning.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023129.7776-1-pkshih@realtek.com
Cleanup the port map calculations, existing masks of having separate
masks for in and out ports is not really required.
Having a single mask for all the ports in the controller is simple and
cuts of some unnecessary code.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240618-soundwire-port-map-v1-1-9644e5545b9b@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Nothing prevents simultaneous ioctl calls to privcmd_irqfd_assign() and
privcmd_irqfd_deassign(). If that happens, it is possible that a kirqfd
created and added to the irqfds_list by privcmd_irqfd_assign() may get
removed by another thread executing privcmd_irqfd_deassign(), while the
former is still using it after dropping the locks.
This can lead to a situation where an already freed kirqfd instance may
be accessed and cause kernel oops.
Use SRCU locking to prevent the same, as is done for the KVM
implementation for irqfds.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/9e884af1f1f842eacbb7afc5672c8feb4dea7f3f.1718703669.git.viresh.kumar@linaro.org
Signed-off-by: Juergen Gross <jgross@suse.com>
irqfd_wakeup() gets EPOLLHUP, when it is called by
eventfd_release() by way of wake_up_poll(&ctx->wqh, EPOLLHUP), which
gets called under spin_lock_irqsave(). We can't use a mutex here as it
will lead to a deadlock.
Fix it by switching over to a spin lock.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/a66d7a7a9001424d432f52a9fc3931a1f345464f.1718703669.git.viresh.kumar@linaro.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Pavel Begunkov says:
====================
zerocopy tx cleanups
Assorted zerocopy send path cleanups, the main part of which is
moving some net stack specific accounting out of io_uring back
to net/ in Patch 4.
====================
Link: https://patch.msgid.link/cover.1719190216.git.asml.silence@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
skb_zerocopy_iter_stream() only uses @orig_uarg in the !link_skb path,
and we can move the local variable in the appropriate block.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, io_uring's io_sg_from_iter() duplicates the part of
__zerocopy_sg_from_iter() charging pages to the socket. It'd be too easy
to miss while changing it in net/, the chunk is not the most
straightforward for outside users and full of internal implementation
details. io_uring is not a good place to keep it, deduplicate it by
moving out of the callback into __zerocopy_sg_from_iter().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of accounting every page range against the socket separately, do
it in batch based on the change in skb->truesize. It's also moved into
__zerocopy_sg_from_iter(), so that zerocopy_fill_skb_from_iter() is
simpler and responsible for setting frags but not the accounting.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Split a function out of __zerocopy_sg_from_iter() that only cares about
the traditional path with refcounted pages and doesn't need to know
about ->sg_from_iter. A preparation patch, we'll improve on the function
later.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
skb_zcopy_set() does nothing if there is already a ubuf_info associated
with an skb, and since ->link_skb should have set it several lines above
the check here essentially does nothing and can be removed. It's also
safer this way, because even if the callback is faulty we'll
have it set.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only difference between the code to setup and dispatch the io in
sync_io() and async_io() is the sync argument to dispatch_io(), which
is used to update the opf argument.
Update the opf argument direcly in sync_io(), and remove the sync
argument from dispatch_io(). Then, make sync_io() call async_io()
instead of duplicting all of its code.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
If dm_io() returned an error, callers that set a notify.fn and wanted it
called on an error need to check the return value and call notify.fn
themselves if it was -EINVAL but not if it was -EIO. None of them do
this (granted, all the existing async_io users of dm_io call it in a way
that is guaranteed to not return an error).
Simplify the interface by never calling the notify.fn if dm_io returns
an error. This works with the existing dm_io callers which check for an
error and handle it using the same methods as the notify.fn.
This also allows us to move the now equivalent num_regions checks out of
sync_io() and async_io() and into dm_io() itself. Additionally, change
async_io() into a void function, since it can no longer fail.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
If dp->get_page() returns a non-zero offset, the bio might need an
additional bvec to deal with the offset. For example, if remaining is
exactly one page size, but there is an offset, the memory will span
two pages.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
This function has been deprecated for some time and is now only used
within the GPIOLIB core. Remove it from the public header and unexport
it as all current users are linked against the compilation unit where
it is defined.
Link: https://lore.kernel.org/r/20240625073815.12376-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
I somehow got a few cpu_nn_reset() signatures wrong in my
patch. Fix it up.
Closes: https://lore.kernel.org/oe-kbuild-all/202406260432.6WGV2jCk-lkp@intel.com/
Fixes: 393999fa96 ("ARM: 9389/2: mm: Define prototypes for all per-processor calls")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Add the STACKLEAK gcc plugin to arm32 by adding the helper used by
stackleak common code: on_thread_stack(). It initialize the stack with the
poison value before returning from system calls which improves the kernel
security. Additionally, this disables the plugin in EFI stub code and
decompress code, which are out of scope for the protection.
Before the test on Qemu versatilepb board:
# echo STACKLEAK_ERASING > /sys/kernel/debug/provoke-crash/DIRECT
lkdtm: Performing direct entry STACKLEAK_ERASING
lkdtm: XFAIL: stackleak is not supported on this arch (HAVE_ARCH_STACKLEAK=n)
After:
# echo STACKLEAK_ERASING > /sys/kernel/debug/provoke-crash/DIRECT
lkdtm: Performing direct entry STACKLEAK_ERASING
lkdtm: stackleak stack usage:
high offset: 80 bytes
current: 280 bytes
lowest: 696 bytes
tracked: 696 bytes
untracked: 192 bytes
poisoned: 7220 bytes
low offset: 4 bytes
lkdtm: OK: the rest of the thread stack is properly erased
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Describe that some HWCAP bits are reserved to avoid that they will be
used by accident.
Suggested-by: Stefan Liebler <stli@linux.ibm.com>
Reviewed-by: Stefan Liebler <stli@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Make the crdte() and cspg() wrappers return a boolean to indicate
success, like the other already existing "compare and swap" type of
wrappers.
Add documentation for those functions as well.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
s390 generates KOBJ_CHANGE uevents on CPUs whenever a topology update
occurs. These uevents currently have no users and they are also not
present on other architectures. As they are not necessary, remove
these extra uevents.
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
perf_callchain_store() return 0 on success, -1 otherwise, fix
callchain_trace() to return correct bool value. So walk_stackframe() can
have a chance to stop walking the stack ahead.
Fixes: 70ccc7c066 ("ARM: 9258/1: stacktrace: Make stack walk callback consistent with generic code")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Optimize the memory usage in struct snd_pcm_runtime - use boolean
value for the standard sync ID scheme.
Introduce snd_pcm_set_sync_per_card function to build synchronization
IDs.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240625172836.589380-3-perex@perex.cz
Until the commit e11f0f90a6 ("ALSA: pcm: remove SNDRV_PCM_IOCTL1_INFO
internal command"), there was a possibility to pass information
about the synchronized streams to the user space. The mentioned
commit removed blindly the appropriate code with an irrelevant comment.
The revert may be appropriate, but since this API was lost for several
years without any complains, it's time to improve it. The hardware
parameters may change the used stream clock source (e.g. USB hardware)
so move this synchronization ID to hw_params as read-only field.
It seems that pipewire can benefit from this API (disable adaptive
resampling for perfectly synchronized PCM streams) now.
Note that the contents of ID is not supposed to be used for direct
comparison with a specific byte sequence. The "empty" case is when
all bytes are zero (driver does not offer this information)
and all other cases must be only used for equal comparison among
PCM streams (including different sound cards) if they are using
identical hardware clock.
Cc: Takashi Sakamoto <takaswie@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240625172836.589380-2-perex@perex.cz
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/xen/xen-pciback/xen-pciback.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/xen/xen-evtchn.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/xen/xen-privcmd.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-xen-v1-1-1eb677364ca6@quicinc.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Replace a comma between expression statements by a semicolon.
Fixes: 8310b77b48 ("Xen/gnttab: handle p2m update errors on a per-slot basis")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240702031010.1411875-1-nichen@iscas.ac.cn
Signed-off-by: Juergen Gross <jgross@suse.com>
Current timer tick is causing some deadline to fail.
The current high value constant was probably due to an old
bug in the Xen timer implementation causing errors if the
deadline was in the future.
This was fixed in Xen commit:
19c6cbd90965 xen/vcpu: ignore VCPU_SSHOTTMR_future
Usage of VCPU_SSHOTTMR_future in Linux kernel was removed by:
c06b6d70fe xen/x86: don't lose event interrupts
Signed-off-by: Frediano Ziglio <frediano.ziglio@cloud.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240619104015.30477-1-frediano.ziglio@cloud.com
Signed-off-by: Juergen Gross <jgross@suse.com>
As it turns out, there is a large number of out-of-tree DTSes (in
OpenWrt project) that used to specify incorrect (active high) polarity
for the Lantiq reset GPIO, so to keep compatibility while they are
being updated a quirk for force the polarity low is needed. Luckily
these old DTSes used nonstandard name for the property ("gpio-reset" vs
"reset-gpios") so the quirk will not hurt if there are any new devices
that need inverted polarity as they can specify the right polarity in
their DTS when using the standard "reset-gpios" property.
Additionally the condition to enable the transition from standard to
non-standard reset GPIO property name was inverted and the replacement
name for the property was not correct. Fix this as well.
Fixes: fbbbcd177a ("gpiolib: of: add quirk for locating reset lines with legacy bindings")
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Reported-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/ZoLpqv1PN08xHioh@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
A couple of error leg problems, one affecting scsi_debug and the other
affecting pure SAS (i.e. not SATA) SCSI expanders.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZoMgiiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYTGAP9/+7vP
DR1Y6KucMx4XjvwkPL5DNxOyobq6poSktn8hqQD/ReaafXaC4H4l7bn2JEpeBO9P
vYog76vSs2jELmEEeHc=
=/weJ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of error leg problems, one affecting scsi_debug and the other
affecting pure SAS (i.e. not SATA) SCSI expanders"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed
scsi: scsi_debug: Fix create target debugfs failure
Convert to new uid/gid option parsing helpers
From: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Link: https://lore.kernel.org/r/58862d35-a026-4866-ab7f-fa09dda8ac1f@redhat.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
According to nxp,dwmac-imx.yaml, 'snps,rx-sched-sp' is not a valid
property.
Remove it from the imx8mp board devicetree files to avoid
dt-schema warnings:
... 'snps,tx-sched-sp' does not match any of the regexes
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When using /proc/interrupts to collect statistics on smp2p interrupt
counts, it is hard to distinguish the different instances of smp2p from
each other. For example to debug a processor boot issue, the ready and
handover interrupts are checked for sanity to ensure the firmware
reached a specific initialization stage.
Remove "smp2p" string from the irq request so that the irq will default
to the device name. Add an .irq_print_chip() callback to print the irq
chip name as the device name. These two changes allow for a unique name
to be used in /proc/interrupts as shown below.
/ # cat /proc/interrupts | grep smp2p
18: ... ipcc 196610 Edge smp2p-adsp
20: ... ipcc 131074 Edge smp2p-modem
170: ... smp2p-modem 1 Edge q6v5 ready
178: ... smp2p-adsp 1 Edge q6v5 ready
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240627104831.4176799-2-quic_sudeepgo@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
