DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM for high power.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240621073458.55187-3-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
It does full calibration when we are going to connect an AP. When switching
bands or channels for scanning or some reasons, reset hardware status to
prevent use wrong power value feedback from previous transmission.
It also loads tables of compensation values reflecting current temperature
into registers according to channel and band group to transmit packets
with expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240621073458.55187-2-pkshih@realtek.com
We add polling after sending LPS H2C to ensure that the Firmware is
received and executes RPWM thereafter. Otherwise, if the Firmware
executes RPWM without receiving LPS H2C, it will cause beacon loss in
WoWLAN mode due to the inability to obtain channel and bandwidth
information from H2C.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-8-pkshih@realtek.com
To avoid wake up by AP disconnection, but no beacon filter setting and
driver can't disconnect successfully. We need to enable beacon filter
after swapping firmware in WoWLAN mode.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-7-pkshih@realtek.com
While downloading Firmware in the resume flow, it is possible to receive
beacon and send H2C to Firmware. However, if Firmware receives unexpected
H2C during the download process, it will fail. Therefore, we prevent to
send unexpected H2C during download Firmware in WoWLAN mode.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-6-pkshih@realtek.com
The 802.11ax chip also needs rtw89_mac_cpu_io_rx(), which notifies Firmware
to start or stop WoWLAN and waits until Firmware process over. Then,
the driver can continue processing to avoid unexpected behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-4-pkshih@realtek.com
Need to update WoWLAN wakeup reason register after firmware version
0.35.22.0 for RTL8922A, and 0.27.80.0 for RTL8852CE.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-3-pkshih@realtek.com
When creating EAPOL_KEY, SA_QUERY and ARP_RSP packet offload, we need
to append security header offset for different cipher as required by
the firmware. Only 8852A, 8852B, 8852BT and 8851B need it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-2-pkshih@realtek.com
All are MM related apart from a MAINTAINERS update. There is no
identifiable theme here - just singleton patches in various places.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZnyyJAAKCRDdBJ7gKXxA
jkcPAQDEsU/erozYjwo2Qq+B03micPCNGLJ6M4pG5t57snwnngEAkQClTiUCjmgK
Xb0H1KkV8ZJUt1gBUnlODXDSf1bhsAE=
=Uj0R
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2024-06-26-17-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"13 hotfixes, 7 are cc:stable.
All are MM related apart from a MAINTAINERS update. There is no
identifiable theme here - just singleton patches in various places"
* tag 'mm-hotfixes-stable-2024-06-26-17-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/memory: don't require head page for do_set_pmd()
mm/page_alloc: Separate THP PCP into movable and non-movable categories
nfs: drop the incorrect assertion in nfs_swap_rw()
mm/migrate: make migrate_pages_batch() stats consistent
MAINTAINERS: TPM DEVICE DRIVER: update the W-tag
selftests/mm:fix test_prctl_fork_exec return failure
mm: convert page type macros to enum
ocfs2: fix DIO failure due to insufficient transaction credits
kasan: fix bad call to unpoison_slab_object
mm: handle profiling for fake memory allocations during compaction
mm/slab: fix 'variable obj_exts set but not used' warning
/proc/pid/smaps: add mseal info for vma
mm: fix incorrect vbq reference in purge_fragmented_block
ARRAY_SIZE is used on multiple places, move its definition in
bpf_misc.h header.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Link: https://lore.kernel.org/bpf/20240626134719.3893748-1-jolsa@kernel.org
TCR2_EL1 handling is missing the handling of its trap configuration:
- HCRX_EL2.TCR2En must be handled in conjunction with HCR_EL2.{TVM,TRVM}
- HFG{R,W}TR_EL2.TCR_EL1 does apply to TCR2_EL1 as well
Without these two controls being implemented, it is impossible to
correctly route TCR2_EL1 traps.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240625130042.259175-7-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As per the architecture, if FEAT_S1PIE is implemented, then FEAT_TCRX
must be implemented as well.
Take advantage of this to avoid checking for S1PIE when TCRX isn't
implemented.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240625130042.259175-6-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
As for other registers, save/restore of TCR2_EL1 should be gated
on the feature being actually present.
In the case of a nVHE hypervisor, it is perfectly fine to leave
the host value in the register, as HCRX_EL2.TCREn==0 imposes that
TCR2_EL1 is treated as 0.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240625130042.259175-4-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
HCRX_GUEST_FLAGS gives random KVM hackers the impression that
they can stuff bits in this macro and unconditionally enable
features in the guest.
In general, this is wrong (we have been there with FEAT_MOPS,
and again with FEAT_TCRX).
Document that HCRX_EL2.SMPME is an exception rather than the rule,
and get rid of HCRX_GUEST_FLAGS.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240625130042.259175-3-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
We currently blindly enable TCR2_EL1 use in a guest, irrespective
of the feature set. This is obviously wrong, and we should actually
honor the guest configuration and handle the possible trap resulting
from the guest being buggy.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20240625130042.259175-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
When building with clang for ARCH=i386, the following errors are
observed:
CC kernel/bpf/btf_relocate.o
./tools/lib/bpf/btf_relocate.c:206:23: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
206 | info[id].needs_size = true;
| ^ ~
./tools/lib/bpf/btf_relocate.c:256:25: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
256 | base_info.needs_size = true;
| ^ ~
2 errors generated.
The problem is we use 1-bit, 31-bit bitfields in a signed int.
Changing to
bool needs_size: 1;
unsigned int size:31;
...resolves the error and pahole reports that 4 bytes are used
for the underlying representation:
$ pahole btf_name_info tools/lib/bpf/btf_relocate.o
struct btf_name_info {
const char * name; /* 0 8 */
unsigned int needs_size:1; /* 8: 0 4 */
unsigned int size:31; /* 8: 1 4 */
__u32 id; /* 12 4 */
/* size: 16, cachelines: 1, members: 4 */
/* last cacheline: 16 bytes */
};
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240624192903.854261-1-alan.maguire@oracle.com
Add translation zh_CN/admin-guide/numastat.rst and link it to
zh_CN/admin-guide/index.rst while clean its todo entry.
commit 77691ee92d ("Documentation: update numastat explanation")
Signed-off-by: Tao Zou <wodemia@linux.alibaba.com>
Reviewed-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Alex Shi <alexs@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/tencent_AB1A2D84652D748A2290F5305B94D4612307@qq.com
In the paragraph titled "Default flow implementations", the helper
function definition (simplified excerpt) for
noop(struct irq_data *data)
had an extraneous closing parenthesis. This commit removes the
unnecessary parenthesis, correcting the function definition.
Signed-off-by: Chih-Wei Chien <idoleat@taiker.tw>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240619160057.128208-1-idoleat@taiker.tw
register store validation for NFT_DATA_VALUE is conditional, however,
the datatype is always either NFT_DATA_VALUE or NFT_DATA_VERDICT. This
only requires a new helper function to infer the register type from the
set datatype so this conditional check can be removed. Otherwise,
pointer to chain object can be leaked through the registers.
Fixes: 96518518cc ("netfilter: add nftables")
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Minor grammar fixes in vmalloced-kernel-stacks
Signed-off-by: Nir Lichtman <nir@lichtman.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240619215944.GA3571421@lichtman.org
When rendering the documentation, the 'html' file extension replaces the
'rst' file extension, not add it. So remove the 'rst' part of the URL.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240620081355.11549-1-didi.debian@cknow.org
Extend the Index of Further Kernel Documentation by adding entries for the
Rust for Linux website, the Linux Foundation's YouTube channel, and notes
on the second edition of Billimoria's kernel programming book. Also,
perform some refactoring: format the text to 75 characters per line and
sort per-section content in chronological order of publication.
Signed-off-by: Carlos Bilbao <carlos.bilbao.osdev@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240622194727.2171845-1-carlos.bilbao.osdev@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
DAMON has its maintainer entry profile document, but it's not listed on
the existing profiles section of maintainer-entry-profile.rst. Add it.
Signed-off-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-7-sj@kernel.org
'Other material' section on 'process/index' is no more necessary since
we have 'staging/' directory. Also all documents on the section has
moved to better places. Remove the section.
Signed-off-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-6-sj@kernel.org
'clang-format' is on 'Other material' section of 'process/index', but it
may fit more under 'dev-tools/' directory. Move it.
Signed-off-by: SeongJae Park <sj@kernel.org>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Acked-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-5-sj@kernel.org
'Other material' section on 'process/index' is for unsorted documents.
However we also have a dedicated place for the purpose, 'staging/'.
Move 'magic-number' from the section to 'staging/' directory.
Signed-off-by: SeongJae Park <sj@kernel.org>
Acked-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-4-sj@kernel.org
'patch-acceptance' on 'Other material' section of 'process/index', which
is for unsorted documents, is actually well organized under
'arch/riscv/' directory, and linked on the index document of the
directory. Remove it from the 'Other material' section.
Signed-off-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-3-sj@kernel.org
'unaligned-memory-access document' is linked on 'Other material' section
of 'core-api/index', which is for unsorted documents. But it is
actually well organized under 'core-api/' directory, and linked on the
'core-api/index'. Remove it from 'Other material' section of
'process/index' document.
Signed-off-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240624185312.94537-2-sj@kernel.org
Mesa VK_KHR_performance_query use case requires preemption and timeslicing
to be disabled for the stream exec queue. Implement this functionality
here.
v2: Minor change to debug print to print both ret values (Umesh)
Acked-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626181817.1516229-3-ashutosh.dixit@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Stream enable/disable functions previously had void return because failure
during function execution was not possible. This will change when we
introduce functionality to disable preemption on the stream exec
queue. Therefore, in preparation for this functionality, prepare this code
to be able to handle error returns.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626181817.1516229-2-ashutosh.dixit@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We shouldn't leave VFs enabled when unloading the PF driver.
Otherwise we will get a message like:
[ ] xe 0000:4d:00.0: driver left SR-IOV enabled after remove
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626111827.1389-2-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The cleanup is done by devres in irq_uninstall.
Commit bbc9651fe9 ("drm/xe/irq: move irq_uninstall over to devm")
resolved the ordering issue where irq_uninstall (registered with drmm)
was called after pci_free_irq_vectors (registered with devm upon calling
pci_alloc_irq_vectors). This happened because drmm action list is
registered with devm very early in the init flow - before
pci_alloc_irq_vectors.
Now that irq_uninstall is registered with devm, it will be called before
pci_free_irq_vectors and we can remove xe_irq_shutdown.
Signed-off-by: Ilia Levi <illevi@habana.ai>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240606124705.822451-1-illevi@habana.ai
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We attempt to unprovision all VFs GuC when disabling them, but
GuC may reject such request if the target VF was previously active
but VF driver didn't unload with explicit VF reset H2G action or
the VMM has not started the VF FLR.
To avoid mismatches between configs maintained the PF and GuC,
trigger an explicit FLR sequences just before releasing resources.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625194546.1301-2-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We maintain GuC error code values in hex format. Also print them
in that format for easier matching.
While at it, slightly reformat the log and add missing \n.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625141258.1257-4-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There are many more error codes used that the GuC firmware can
return in the RESPONSE_FAILURE message. Add to the ABI header
those which are more likely to be seen by the PF or VF drivers.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625141258.1257-3-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The G2H RETRY message sent by the GuC does not necessary indicate
any serious problem and can be a part of the normal communication
flow. Switch the log level from warning to more appropriate debug.
This will also let the CI ignore these logs which were seen in few
SR-IOV scenarios.
While at it, use hex to print the reason and add missing \n.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625141258.1257-2-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We have already marked the GuC PC feature as not applicable for
VF devices, but we missed the fact that there may be still some
privileged activities performed by this component, who does much
more than its name suggests.
Explicitly skip xe_guc_pc_start() if running as a VF driver and
use a GT oriented message to report any error.
v2: also skip xe_guc_pc_stop (Vinay)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240622094253.1081-1-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fix kernel doc in xe_drm.h. Also eliminate private/non-abi enum
definitions.
v2: Remove __DRM_XE_PERF_TYPE_MAX since it is unused (Michal)
v3: Also remove DRM_XE_OA_PROPERTY_MAX since it can also be
eliminated (Michal)
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240623203119.3840283-1-ashutosh.dixit@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If applicable, we prefer GT oriented dmesg messages. Update all
HuC related messages and use more user friendly error codes.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240621172522.1037-1-michal.wajdeczko@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We already request max freq in the load path, moving it
to __xe_guc_upload will ensure this speeds up GuC load in
the resume path as well.
v2: Rename xe_guc_pc_init_early since we now call it per
GuC load (Michal W)
v3: Keep pc_init_early() and init RPx values there (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240620224928.3986377-3-vinay.belgaumkar@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This WA requires us to limit media GT frequency requests to a certain
cap value during driver load. Freq limits are restored after load
completes, so perf will not be affected during normal operations.
During normal driver operation, this WA requires dummy writes to media
offset 0x380D8C after every ~63 GGTT writes. This will ensure completion
of the LMEM writes originating from Gunit.
During driver unload(before FLR), the WA requires that we set requested
frequency to the cap value again.
v3: Do not use WA number in function name. Call WA wrapper from xe_device.
Rename some variables, check for locks in the correct function (Rodrigo).
Ensure reset path is also covered for this WA.
v4: Fix BAT failure
v5: Add a function pointer for ggtt_ops (Michal W)
v6: Fix name collision and use static function (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240620224928.3986377-2-vinay.belgaumkar@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Need to sync some header include that propagated through
drm-intel-next.
v2: After some changes in drm/drm-next
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Two patches to fix kworker name formatting.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCZnyHUw4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGV8AAQCi2flF10nHfE+nPsji8Z2FWtDKIzemsKgmxSnW
VvThlAD+MeK29fbz0uZzFa65TqIeckf7DGoGQpKnMzC7+FeJWAc=
=6POk
-----END PGP SIGNATURE-----
Merge tag 'wq-for-6.10-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Two patches to fix kworker name formatting"
* tag 'wq-for-6.10-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Increase worker desc's length to 32
workqueue: Refactor worker ID formatting and make wq_worker_comm() use full ID string
Updates the documentation in `amd-pstate.rst` to include information about
the per CPU boost control feature. Users can now enable or disable the
Core Performance Boost (CPB) feature on individual CPUs using the `boost`
sysfs attribute.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240626042733.3747-5-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
