This WA needs to be applied to graphics GT when the media version
is 2000. Currently, media version 2000 is always paired with
graphics version 2004 which will result in writing same register
with same bits twice. We can't add optional rule in rtp
framework and also writing same register with same bits gives
warning.
Currently, media version 2000 is always paired with graphics version
2004, so just checking the latter is sufficient.
V2(Lucas):
- Add more detail in commit message
- Improve code comment to follow guideline
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2016
Fixes: 131328aa56 ("drm/xe/xe2lpm: Add permanent Wa_14020756599")
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607122528.1048610-1-tejas.upadhyay@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Add the description to the parameters addr and free_filters
of the function unregister_ftrace_direct().
Link: https://lore.kernel.org/linux-trace-kernel/20240606132520.1397567-1-marilene.agarcia@gmail.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Marilene A Garcia <marilene.agarcia@gmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Yang Li sent a patch to fix the kerneldoc of ftrace_graph_ret_addr().
While reviewing it, I realized that the comments in the entire function
header needed a rewrite. When doing that, I realized that @idx parameter
was being ignored. Every time this was called by the unwinder, it would
start the loop at the top of the shadow stack and look for the matching
stack pointer. When it found it, it would return it. When the unwinder
asked for the next function, it would search from the beginning again.
In reality, it should start from where it left off. That was the reason
for the @idx parameter in the first place. The first time the unwinder
calls this function, the @idx pointer would contain zero. That would mean
to start from the top of the stack. The function was supposed to update
the @idx with the index where it found the return address, so that the
next time the unwinder calls this function it doesn't have to search
through the previous addresses it found (making it O(n^2)!).
This speeds up the unwinder's use of ftrace_graph_ret_addr() by an order
of magnitude.
Link: https://lore.kernel.org/linux-trace-kernel/20240610181746.656e3759@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20240611031737.821995106@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Reported-by: Yang Li <yang.lee@linux.alibaba.com>
Fixes: 7aa1eaef9f ("function_graph: Allow multiple users to attach to function graph")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Split conversion deliberately into minimal pieces to ease bisection
because debugging alternatives is a nightmare.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240607111701.8366-4-bp@kernel.org
Instead of making increasingly complicated ALTERNATIVE_n()
implementations, use a nested alternative expression.
The only difference between:
ALTERNATIVE_2(oldinst, newinst1, flag1, newinst2, flag2)
and
ALTERNATIVE(ALTERNATIVE(oldinst, newinst1, flag1),
newinst2, flag2)
is that the outer alternative can add additional padding when the inner
alternative is the shorter one, which then results in
alt_instr::instrlen being inconsistent.
However, this is easily remedied since the alt_instr entries will be
consecutive and it is trivial to compute the max(alt_instr::instrlen) at
runtime while patching.
Specifically, after this the ALTERNATIVE_2 macro, after CPP expansion
(and manual layout), looks like this:
.macro ALTERNATIVE_2 oldinstr, newinstr1, ft_flags1, newinstr2, ft_flags2
740:
740: \oldinstr ;
741: .skip -(((744f-743f)-(741b-740b)) > 0) * ((744f-743f)-(741b-740b)),0x90 ;
742: .pushsection .altinstructions,"a" ;
altinstr_entry 740b,743f,\ft_flags1,742b-740b,744f-743f ;
.popsection ;
.pushsection .altinstr_replacement,"ax" ;
743: \newinstr1 ;
744: .popsection ; ;
741: .skip -(((744f-743f)-(741b-740b)) > 0) * ((744f-743f)-(741b-740b)),0x90 ;
742: .pushsection .altinstructions,"a" ;
altinstr_entry 740b,743f,\ft_flags2,742b-740b,744f-743f ;
.popsection ;
.pushsection .altinstr_replacement,"ax" ;
743: \newinstr2 ;
744: .popsection ;
.endm
The only label that is ambiguous is 740, however they all reference the
same spot, so that doesn't matter.
NOTE: obviously only @oldinstr may be an alternative; making @newinstr
an alternative would mean patching .altinstr_replacement which very
likely isn't what is intended, also the labels will be confused in that
case.
[ bp: Debug an issue where it would match the wrong two insns and
and consider them nested due to the same signed offsets in the
.alternative section and use instr_va() to compare the full virtual
addresses instead.
- Use new labels to denote that the new, nested
alternatives are being used when staring at preprocessed output.
- Use the %c constraint everywhere instead of %P and document the
difference for future reference. ]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230628104952.GA2439977@hirez.programming.kicks-ass.net
The forcewake count and domains listing is multi process critical
and the uncore provides a spinlock for such cases.
Lock the forcewake evaluation section in the fw_domains_show()
debugfs interface.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607145131.217251-1-andi.shyti@linux.intel.com
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Replace or drop the legacy header that is subject to remove.
Not all of them were compile-tested, the series might have
hidden compilation errors.
Commit ac0c26bae6 ("hwmon: (lm25066) Use i2c_get_match_data()") changed
enum chips to start with 1 instead of 0, under the assumption that
the data pointer in of_device_id must not start with 0 (NULL) if
i2c_get_match_data() is used. However, that is perfectly fine as long as
there is also an i2c_device_id array with the same data which is used
as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 10a0575ea0 ("hwmon: (nct6775-i2c) Use i2c_get_match_data()")
introduced calling i2c_get_match_data() to the nct6775 driver. As part
of that commit, enum kinds was changed to start with 1, based on
Adjust the 'kinds' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
The patch had to be fixed later with commit 2792fc8f8c ("hwmon:
(nct6775-core) Explicitly initialize nct6775_device_names indexes") and
commit efe86092ab ("hwmon: (nct6775-platform) Explicitly initialize
nct6775_sio_names indexes").
Various patches submitted later show that the change from 0 to 1 is
not really necessary. As it turns out, it is perfectly fine as long as
there is an i2c_device_id array with the same data as in the of_device_id
array. This data is used as fallback if the data pointer in struct
of_device_id is NULL (0).
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Earlier it was assumed that the data pointer in of_device_id must not start
with 0 (NULL) if i2c_get_match_data() is used. However, it turns out that
this is perfectly fine as long as there is also an i2c_device_id array with
the same data, which is used as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
While doing that, remove chip_id from struct mp2856_data since it is only
used in the probe function, and typecast the result of i2c_get_match_data()
to kernel_ulong_t to avoid the double typecast.
Cc: Peter Yin <peteryin.openbmc@gmail.com>
Cc: Potin Lai <potin.lai.pt@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a driver calls device_get_match_data(), the .data pointer in its id
data structures must not be NULL/0 because device_get_match_data()
returns NULL if an entry is not found. Explain that in a comment to avoid
confusion why this is required in this driver but not in other drivers.
Cc: Daniel Matyas <daniel.matyas@analog.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since physical and virtual kernel address spaces are uncoupled
the kernel image is not mapped using large segment pages anymore,
which is a regression.
Put the kernel image at the same large segment page offset in
physical memory as in virtual memory. Such approach preserves
the existing number of bits of entropy used for randomization
of the kernel location in virtual memory when KASLR is on.
As result, the kernel is mapped using large segment pages.
Fixes: c98d2ecae0 ("s390/mm: Uncouple physical vs virtual address spaces")
Reported-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Do not allow creation of large pages against physical addresses,
which itself are not aligned on the correct boundary. Failure to
do so might lead to referencing wrong memory as result of the way
DAT works.
Fixes: c98d2ecae0 ("s390/mm: Uncouple physical vs virtual address spaces")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The WA should be extended to cover VDBOX engine. We found that
28-channels 1080p VP9 encoding may hit this issue.
v3: update the WA number and explain the reason why
this workaround is needed
v2: add WA number
v1: initial version
Signed-off-by: Angus Chen <angus.chen@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426073638.45775-1-angus.chen@intel.com
It was discovered that some device have CBR address set to 0 causing
kernel panic when arch_sync_dma_for_cpu_all is called.
This was notice in situation where the system is booted from TP1 and
BMIPS_GET_CBR() returns 0 instead of a valid address and
!!(read_c0_brcm_cmt_local() & (1 << 31)); not failing.
The current check whether RAC flush should be disabled or not are not
enough hence lets check if CBR is a valid address or not.
Fixes: ab327f8acd ("mips: bmips: BCM6358: disable RAC flush for TP1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API") not
only switched to the gpiod API, but also inverted / changed the polarity
of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
read_config_dword() contains strange condition checking ret for a
number of values. The ret variable, however, is always zero because
config_access() never returns anything else. Thus, the retry is always
taken until number of tries is exceeded.
The code looks like it wants to check *val instead of ret to see if the
read gave an error response.
Fixes: 73b4390fb2 ("[MIPS] Routerboard 532: Support for base system")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The reference count is bumped by device_get_named_child_node()
and never dropped. Since LED APIs do not require it to be
bumped by the user, drop the reference after LED registration.
[andy: rewritten the commit message and amended the change]
Fixes: c223d9c636 ("auxdisplay: ht16k33: Add LED support")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Originally reported here:
https://github.com/thesofproject/avs-topology-xml/issues/22#issuecomment-2127892605
There is various level of failure there, first of all when topology
loads routes, it points directly into FW file, but it may be freed after
topology load. After fixing the above, when avs driver parses topology
it should allocate its own memory, as target strings can be shorter than
needed. Also clean up soc_tplg_dapm_graph_elems_load() a bit.
These functions are used in only one file.
Made them static to fix the following build error:
arch/mips/sgi-ip22/ip22-gio.c:249:6: error: no previous prototype for ‘ip22_gio_set_64bit’ [-Werror=missing-prototypes]
arch/mips/sgi-ip22/ip22-gio.c:398:12: error: no previous prototype for ‘ip22_gio_init’ [-Werror=missing-prototypes]
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This fixes the following build warning:
arch/mips/sgi-ip22/ip22-time.c:119:18: error: no previous prototype for ‘indy_8254timer_irq’ [-Werror=missing-prototypes]
arch/mips/sgi-ip22/ip22-berr.c:89:6: error: no previous prototype for ‘ip22_be_interrupt’ [-Werror=missing-prototypes]
arch/mips/sgi-ip22/ip22-berr.c:113:13: error: no previous prototype for ‘ip22_be_init’ [-Werror=missing-prototypes]
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add various required properties to silent warnings:
arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi:116.16-297.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add it to silent warning:
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts:32.31-40.4: Warning (interrupt_provider): /bus@10000000/msi-controller@2ff00000: Missing '#interrupt-cells' in interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
dma.c defined function plat_swiotlb_setup, which is declared in
bootinfo.h.
Fixes warning:
arch/mips/loongson64/dma.c:25:13: warning: no previous prototype for ‘plat_swiotlb_setup’ [-Wmissing-prototypes]
25 | void __init plat_swiotlb_setup(void)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Implement PM suspend for LEFI firmware.
Entering STR (Suspend to RAM) is as simple as save our context
then go to a firmware vector.
Wake is a little bit treaky as we need to setup some CP0 status
first, which can be done with smp_slave_setup.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Functionalities provided by CPU_PM are essential for suspend
to work on all platforms.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Use platform agnostic macros so it can be compiled on all
MIPS platforms.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 4fc8cb47fc ("drm/display: Move HDMI helpers into display-helper
module") turned the DRM_DW_HDMI dependency of DRM_INGENIC_DW_HDMI into a
depends on which ended up disabling the drivers in the defconfig. Make
sure it's still enabled.
Fixes: 4fc8cb47fc ("drm/display: Move HDMI helpers into display-helper module")
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
The first part of the series (patches 1 to 7) is an introduction
of a new helper followed by the user conversion.
This consolidates the same code and also makes patch 8 (last one)
be localised to the SPI core part.
The last patch is the main rework to get rid of a recently introduced
hack with a dummy SG list and move to the transfer-based DMA mapped
flag.
That said, the patches 1 to 7 may be applied right away since they
have no functional change intended, while the last one needs more
testing and reviewing.
If the card doesn't have display hardware, hpd_work and hpd_lock are
left uninitialized which causes BUG when attempting to schedule hpd_work
on runtime PM resume.
Fix it by adding headless flag to DRM and skip any hpd if it's set.
Fixes: ae1aadb1eb ("nouveau: don't fail driver load if no display hw present.")
Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/337
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607221032.25918-1-anarsoul@gmail.com
SU SDP scanline indication should be taken into account when checking
vblank length. In Bspec we have:
PSR2_CTL[ SU SDP scanline indication ] = 0: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start) > PSR2_CTL Block Count Number value
in lines
PSR2_CTL[ SU SDP scanline indication ] = 1: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start- 1) > PSR2_CTL Block Count Number
value in lines
Bspec: 49274
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-12-jouni.hogander@intel.com
We are about to add more complexity to vblank length check. It makes sense
to move it to separate function for sake of clarity.
v2: change name to wake_lines_fit_into_vblank
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-11-jouni.hogander@intel.com
Currently Panel Replay status printout is printing frame lock status. It
should print Panel Replay status instead. Panel Replay status register
field follows PSR status register field. Use existing PSR code for that.
Fixes: ef75c25e8f ("drm/i915/panelreplay: Debugfs support for panel replay")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-10-jouni.hogander@intel.com
Early Transport is possible and in our HW mandatory on eDP Panel
Replay. Add parameter to intel_psr2_config_et_valid to differentiate
validity check for Panel Replay.
v2: fix intel_dp->psr_dpcd[0] check
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-9-jouni.hogander@intel.com
Current intel_psr_enable_sink is a mess due to partly reusing PSR bit
definitions for Panel Replay. Even thought PSR and Panel Replay enable
registers do have common bits they still have also different bits and same
bits with different meaning. For sake of clarity split enabling sink to PSR
and Panel Replay specific parts.
Also fix issue caused by using psr->panel_replay_enabled to early.
Fixes: 88ae6c65ec ("drm/i915/psr: Unify panel replay enable/disable sink")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-7-jouni.hogander@intel.com
Panel Replay is not enabled if there are no active planes. Do not compare
it on pipe comparison. Otherwise we get pipe mismatch.
Fixes: ac9ef32732 ("drm/i915/psr: Panel replay has to be enabled before link training")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-5-jouni.hogander@intel.com
We want to have own variables for fast wake lines and aux less wake
time. It might be needed to choose if we can enable Panel Replay Selective
Update or PSR2.
Also currently aux less wake time is overwritten by calculated fast wake
time.
v2:use aux less wake time in intel_alpm_lobf_compute_config
Fixes: da6a9836ac ("drm/i915/psr: Calculate aux less wake time")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-2-jouni.hogander@intel.com
This reverts commit a3fad2e92c.
The core components of the subsystem no longer assume that low-level
modules register a driver for the parent device and rely on its owner
pointer to take the module's refcount. KUnit test suites can now be safely
re-enabled with loadable module support.
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240604102536.59010-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
