After removing architectural code the helper function
acpi_numa_memory_affinity_init() is no longer needed. Squash it into
acpi_parse_memory_affinity(). No functional changes intended.
While at it, fixing checkpatch complaints in code moved.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202403220943.96dde419-oliver.sang@intel.com
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After removing architectural code the helper function
acpi_numa_slit_init() is no longer needed. Squash it into
acpi_parse_slit(). No functional changes intended.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the removal of the Itanium architecture [1] the last architecture
dependent functions:
acpi_numa_slit_init(), acpi_numa_memory_affinity_init()
were removed. Remove its remainings in the header files too and make
them static.
[1] commit cf8e865810 ("arch: Remove Itanium (IA-64) architecture")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For configurations that have the kconfig option NUMA_KEEP_MEMINFO
disabled, numa_fill_memblks() only returns with NUMA_NO_MEMBLK (-1).
SRAT lookup fails then because an existing SRAT memory range cannot be
found for a CFMWS address range. This causes the addition of a
duplicate numa_memblk with a different node id and a subsequent page
fault and kernel crash during boot.
Fix this by making numa_fill_memblks() always available regardless of
NUMA_KEEP_MEMINFO.
As Dan suggested, the fix is implemented to remove numa_fill_memblks()
from sparsemem.h and alos using __weak for the function.
Note that the issue was initially introduced with [1]. But since
phys_to_target_node() was originally used that returned the valid node
0, an additional numa_memblk was not added. Though, the node id was
wrong too, a message is seen then in the logs:
kernel/numa.c: pr_info_once("Unknown target node for memory at 0x%llx, assuming node 0\n",
[1] commit fd49f99c18 ("ACPI: NUMA: Add a node and memblk for each
CFMWS not in SRAT")
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/all/66271b0072317_69102944c@dwillia2-xfh.jf.intel.com.notmuch/
Fixes: 8f10046799 ("ACPI/NUMA: Apply SRAT proximity domain to entire CFMWS window")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lenovo Slim 7 16ARH7 is a machine with switchable graphics between AMD
and Nvidia, and the backlight can't be adjusted properly unless
acpi_backlight=native is passed. Although nvidia-wmi-backlight is
present and loaded, this doesn't work as expected at all.
For making it working as default, add the corresponding quirk entry
with a DMI matching "LENOVO" "82UX".
Link: https://bugzilla.suse.com/show_bug.cgi?id=1217750
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
page_pool::p is driver-defined params, copied directly from the
structure passed to page_pool_create(). The structure isn't meant
to be modified by the Page Pool core code and this even might look
confusing[0][1].
In order to be able to alter some flags, let's define our own, internal
fields the same way as the already existing one (::has_init_callback).
They are defined as bits in the driver-set params, leave them so here
as well, to not waste byte-per-bit or so. Almost 30 bits are still free
for future extensions.
We could've defined only new flags here or only the ones we may need
to alter, but checking some flags in one place while others in another
doesn't sound convenient or intuitive. ::flags passed by the driver can
now go to the "slow" PP params.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link[0]: https://lore.kernel.org/netdev/20230703133207.4f0c54ce@kernel.org
Suggested-by: Alexander Duyck <alexanderduyck@fb.com>
Link[1]: https://lore.kernel.org/netdev/CAKgT0UfZCGnWgOH96E4GV3ZP6LLbROHM7SHE8NKwq+exX+Gk_Q@mail.gmail.com
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
After commit 5027ec19f1 ("net: page_pool: split the page_pool_params
into fast and slow") that made &page_pool contain only "hot" params at
the start, cacheline boundary chops frag API fields group in the middle
again.
To not bother with this each time fast params get expanded or shrunk,
let's just align them to `4 * sizeof(long)`, the closest upper pow-2 to
their actual size (2 longs + 1 int). This ensures 16-byte alignment for
the 32-bit architectures and 32-byte alignment for the 64-bit ones,
excluding unnecessary false-sharing.
::page_state_hold_cnt is used quite intensively on hotpath no matter if
frag API is used, so move it to the newly created hole in the first
cacheline.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Quite often, devices do not need dma_sync operations on x86_64 at least.
Indeed, when dev_is_dma_coherent(dev) is true and
dev_use_swiotlb(dev) is false, iommu_dma_sync_single_for_cpu()
and friends do nothing.
However, indirectly calling them when CONFIG_RETPOLINE=y consumes about
10% of cycles on a cpu receiving packets from softirq at ~100Gbit rate.
Even if/when CONFIG_RETPOLINE is not set, there is a cost of about 3%.
Add dev->need_dma_sync boolean and turn it off during the device
initialization (dma_set_mask()) depending on the setup:
dev_is_dma_coherent() for the direct DMA, !(sync_single_for_device ||
sync_single_for_cpu) or the new dma_map_ops flag, %DMA_F_CAN_SKIP_SYNC,
advertised for non-NULL DMA ops.
Then later, if/when swiotlb is used for the first time, the flag
is reset back to on, from swiotlb_tbl_map_single().
On iavf, the UDP trafficgen with XDP_DROP in skb mode test shows
+3-5% increase for direct DMA.
Suggested-by: Christoph Hellwig <hch@lst.de> # direct DMA shortcut
Co-developed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some platforms do have DMA, but DMA there is always direct and coherent.
Currently, even on such platforms DMA sync operations are compiled and
called.
Add a new hidden Kconfig symbol, DMA_NEED_SYNC, and set it only when
either sync operations are needed or there is DMA ops or swiotlb
or DMA debug is enabled. Compile global dma_sync_*() and dma_need_sync()
only when it's set, otherwise provide empty inline stubs.
The change allows for future optimizations of DMA sync calls depending
on runtime conditions.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
iommu_dma_map_page() allocates swiotlb memory as a bounce buffer when an
untrusted device wants to map only part of the memory in an granule. The
goal is to disallow the untrusted device having DMA access to unrelated
kernel data that may be sharing the granule. To meet this goal, the
bounce buffer itself is zeroed, and any additional swiotlb memory up to
alloc_size after the bounce buffer end (i.e., "post-padding") is also
zeroed.
However, as of commit 901c7280ca ("Reinstate some of "swiotlb: rework
"fix info leak with DMA_FROM_DEVICE"""), swiotlb_tbl_map_single() always
initializes the contents of the bounce buffer to the original memory.
Zeroing the bounce buffer is redundant and probably wrong per the
discussion in that commit. Only the post-padding needs to be zeroed.
Also, when the DMA min_align_mask is non-zero, the allocated bounce
buffer space may not start on a granule boundary. The swiotlb memory
from the granule boundary to the start of the allocated bounce buffer
might belong to some unrelated bounce buffer. So as described in the
"second issue" in [1], it can't be zeroed to protect against untrusted
devices. But as of commit af133562d5 ("swiotlb: extend buffer
pre-padding to alloc_align_mask if necessary"), swiotlb_tbl_map_single()
allocates pre-padding slots when necessary to meet min_align_mask
requirements, making it possible to zero the pre-padding area as well.
Finally, iommu_dma_map_page() uses the swiotlb for untrusted devices
and also for certain kmalloc() memory. Current code does the zeroing
for both cases, but it is needed only for the untrusted device case.
Fix all of this by updating iommu_dma_map_page() to zero both the
pre-padding and post-padding areas, but not the actual bounce buffer.
Do this only in the case where the bounce buffer is used because
of an untrusted device.
[1] https://lore.kernel.org/all/20210929023300.335969-1-stevensd@google.com/
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Petr Tesarik <petr@tesarici.cz>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently swiotlb_tbl_map_single() takes alloc_align_mask and
alloc_size arguments to specify an swiotlb allocation that is larger
than mapping_size. This larger allocation is used solely by
iommu_dma_map_single() to handle untrusted devices that should not have
DMA visibility to memory pages that are partially used for unrelated
kernel data.
Having two arguments to specify the allocation is redundant. While
alloc_align_mask naturally specifies the alignment of the starting
address of the allocation, it can also implicitly specify the size
by rounding up the mapping_size to that alignment.
Additionally, the current approach has an edge case bug.
iommu_dma_map_page() already does the rounding up to compute the
alloc_size argument. But swiotlb_tbl_map_single() then calculates the
alignment offset based on the DMA min_align_mask, and adds that offset to
alloc_size. If the offset is non-zero, the addition may result in a value
that is larger than the max the swiotlb can allocate. If the rounding up
is done _after_ the alignment offset is added to the mapping_size (and
the original mapping_size conforms to the value returned by
swiotlb_max_mapping_size), then the max that the swiotlb can allocate
will not be exceeded.
In view of these issues, simplify the swiotlb_tbl_map_single() interface
by removing the alloc_size argument. Most call sites pass the same value
for mapping_size and alloc_size, and they pass alloc_align_mask as zero.
Just remove the redundant argument from these callers, as they will see
no functional change. For iommu_dma_map_page() also remove the alloc_size
argument, and have swiotlb_tbl_map_single() compute the alloc_size by
rounding up mapping_size after adding the offset based on min_align_mask.
This has the side effect of fixing the edge case bug but with no other
functional change.
Also add a sanity test on the alloc_align_mask. While IOMMU code
currently ensures the granule is not larger than PAGE_SIZE, if that
guarantee were to be removed in the future, the downstream effect on the
swiotlb might go unnoticed until strange allocation failures occurred.
Tested on an ARM64 system with 16K page size and some kernel test-only
hackery to allow modifying the DMA min_align_mask and the granule size
that becomes the alloc_align_mask. Tested these combinations with a
variety of original memory addresses and sizes, including those that
reproduce the edge case bug:
* 4K granule and 0 min_align_mask
* 4K granule and 0xFFF min_align_mask (4K - 1)
* 16K granule and 0xFFF min_align_mask
* 64K granule and 0xFFF min_align_mask
* 64K granule and 0x3FFF min_align_mask (16K - 1)
With the changes, all combinations pass.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Petr Tesarik <petr@tesarici.cz>
Signed-off-by: Christoph Hellwig <hch@lst.de>
drm_color_ctm_3x4 is some undocumented amgdpu private
uapi and thus has no business being in drm_mode.h.
At least move it to some amdgpu specific header, albeit
with the wrong namespace as maybe something somewhere
is using this already?
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: 6872a189be ("drm/amd/display: Add 3x4 CTM support for plane CTM")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240422085857.17651-1-ville.syrjala@linux.intel.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Starting BDB version 239, hdr_dpcd_refresh_timeout is introduced to
backlight BDB data. Commit 700034566d ("drm/i915/bios: Define more BDB
contents") updated the backlight BDB data accordingly. This broke the
parsing of backlight BDB data in VBT for versions 236 - 238 (both
inclusive) and hence the backlight controls are not responding on units
with the concerned BDB version.
backlight_control information has been present in backlight BDB data
from at least BDB version 191 onwards, if not before. Hence this patch
extracts the backlight_control information for BDB version 191 or newer.
Tested on Chromebooks using Jasperlake SoC (reports bdb->version = 236).
Tested on Chromebooks using Raptorlake SoC (reports bdb->version = 251).
v2: removed checking the block size of the backlight BDB data
[vsyrjala: this is completely safe thanks to commit e163cfb4c9
("drm/i915/bios: Make copies of VBT data blocks")]
Fixes: 700034566d ("drm/i915/bios: Define more BDB contents")
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221180622.v2.1.I0690aa3e96a83a43b3fc33f50395d334b2981826@changeid
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
'timeout' is a vague name for the return value of wait_event_*_timeout
because it actually returns the time left. Because the variable is never
used later, just drop the return value. Since variable 'timeout' is then
only used to carry a fixed timeout value, drop this in favor of a fixed
function argument as in the other call to wait_event_timeout() above.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
In ath12k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-6-quic_kangyang@quicinc.com
ath12k_mac_op_unassign_vif_chanctx() will do vdev down in function
ath12k_mac_monitor_stop(). So no need to do vdev down again.
remove the duplicated one.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-4-quic_kangyang@quicinc.com
ath12k_mac_op_unassign_vif_chanctx() will do vdev stop in
ath12k_mac_monitor_stop(). This ath12k_mac_vdev_stop() will do vdev stop
again, then might trigger firmware crash.
So add judgement to avoid duplicated vdev stop.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: c9e4e41e71 ("wifi: ath12k: move peer delete after vdev stop of station for WCN7850")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-3-quic_kangyang@quicinc.com
monitor_flags is defined in struct ath12k. Although it is changed in
some places, but it is not actually used.
So remove related code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-2-quic_kangyang@quicinc.com
Currently memory allocation for multiple hardware rings done
in host as these memory will be used by firmware/hardware.
But in case of tcl_cmd_ring and tcl_status_ring neither firmware
nor hardware uses host allocated memory and it uses memory
allocated by firmware itself. So avoid tcl_cmd_ring and
tcl_status_ring setup in host.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430091414.2486196-4-quic_tamizhr@quicinc.com
Currently tx monitor is not supported in driver. So remove
the tx monitor ring configuration, allocation and handling.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430091414.2486196-3-quic_tamizhr@quicinc.com
Currently in ath12k_dp_tx_htt_monitor_mode_ring_config()
ath12k_dp_tx_htt_tx_monitor_mode_ring_config() function wrongly called twice.
Fix that by calling ath12k_dp_tx_htt_rx_monitor_mode_ring_config().
Currently monitor mode is disabled in driver so the change is compile
tested and boot sequence verified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430091414.2486196-2-quic_tamizhr@quicinc.com
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct wil6210_priv by converting it
into a pointer. Then use the leverage alloc_netdev_dummy() to allocate
the net_device object at wil_if_add(). The free of the device
occurs at wil_if_remove().
Link: https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240503103304.339489-1-leitao@debian.org
If STATUS_BUFFER_DONE is not set for a monitor status ring entry,
we don't process the status ring until STATUS_BUFFER_DONE set
for that status ring entry.
During LMAC reset it may happen that hardware will not write
STATUS_BUFFER_DONE tlv in status buffer, in that case we end up
waiting for STATUS_BUFFER_DONE leading to backpressure on monitor
status ring.
To fix the issue, when HP (Head Pointer) + 1 entry is peeked and if DMA is not
done and if HP + 2 entry's DMA done is set, replenish HP + 1 entry and start
processing in next interrupt. If HP + 2 entry's DMA done is not set, poll onto
HP + 1 entry DMA done to be set.
Also, during monitor attach HP points to the end of the ring and TP (Tail
Pointer) points to the start of the ring. Using ath11k_hal_srng_src_peek() may
result in processing invalid buffer for the very first interrupt. Since, HW
starts writing buffer from TP.
To avoid this issue call ath11k_hal_srng_src_next_peek() instead of
calling ath11k_hal_srng_src_peek().
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Co-developed-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429073624.736147-1-quic_tamizhr@quicinc.com
Daniel Jurgens says:
====================
Remove RTNL lock protection of CVQ
Currently the buffer used for control VQ commands is protected by the
RTNL lock. Previously this wasn't a major concern because the control VQ
was only used during device setup and user interaction. With the recent
addition of dynamic interrupt moderation the control VQ may be used
frequently during normal operation.
This series removes the RNTL lock dependency by introducing a mutex
to protect the control buffer and writing SGs to the control VQ.
v6:
- Rebased over new stats code.
- Added comment to cvq_lock, init the mutex unconditionally,
and replaced some duplicate code with a goto.
- Fixed minor grammer errors, checkpatch warnings, and clarified
a comment.
v5:
- Changed cvq_lock to a mutex.
- Changed dim_lock to mutex, because it's held taking
the cvq_lock.
- Use spin/mutex_lock/unlock vs guard macros.
v4:
- Protect dim_enabled with same lock as well intr_coal.
- Rename intr_coal_lock to dim_lock.
- Remove some scoped_guard where the error path doesn't
have to be in the lock.
v3:
- Changed type of _offloads to __virtio16 to fix static
analysis warning.
- Moved a misplaced hunk to the correct patch.
v2:
- New patch to only process the provided queue in
virtnet_dim_work
- New patch to lock per queue rx coalescing structure.
====================
Link: https://lore.kernel.org/r/20240503202445.1415560-1-danielj@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rtnl lock is no longer needed to protect the control buffer and
command VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Once the RTNL locking around the control buffer is removed there can be
contention on the per queue RX interrupt coalescing data. Use a mutex
per queue. A mutex is required because virtnet_send_command can sleep.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since we no longer have to hold the RTNL lock here just do updates for
the specified queue.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The command VQ will no longer be protected by the RTNL lock. Use a
mutex to protect the control buffer header and the VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allocate memory for the data when it's used. Ideally the struct could
be on the stack, but we can't DMA stack memory. With this change only
the header and status memory are shared between commands, which will
allow using a tighter lock than RTNL.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop storing RSS setting in the control buffer. This is prep work for
removing RTNL lock protection of the control buffer.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537 ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus"), we can describe the switch PHYs on the MDIO bus of
the switch on the device tree. Extend the check to detect PHY muxing when
the PHY is defined on the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240430-b4-for-netnext-mt7530-use-switch-mdio-bus-for-phy-muxing-v2-1-9104d886d0db@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 9385/2 introduced a few branches inside function
prototypes when using CFI in order to deal with the situation
where CFI inserts a few bytes of function information in front
of the symbol.
This is not good for older CPUs where every cycle counts.
Commit 9386/2 alleviated the situation a bit by using aliases
for the cache functions with identical signatures.
This leaves the coherent cache flush functions
*_coherent_kern_range() with these branches to the corresponing
*_coherent_user_range() around, since their return type differ and
they therefore cannot be aliased.
Solve this by a simple ifdef so at least we can use fallthroughs
when compiling without CFI enabled.
Link: https://lore.kernel.org/linux-arm-kernel/Zi+e9M%2Ff5b%2FSto9H@shell.armlinux.org.uk/
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Eric Dumazet says:
====================
rtnetlink: more rcu conversions for rtnl_fill_ifinfo()
We want to no longer rely on RTNL for "ip link show" command.
This is a long road, this series takes care of some parts.
====================
Link: https://lore.kernel.org/r/20240503192059.3884225-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
All rtnl_link_ops->get_link_net() methods already using dev_net()
are ready. I added READ_ONCE() annotations on others.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev->xdp_prog is protected by RCU, we can lift RTNL requirement
from rtnl_xdp_prog_skb().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Change dev_change_proto_down() and dev_change_proto_down_reason()
to write once on dev->proto_down and dev->proto_down_reason.
Then rtnl_fill_proto_down() can use READ_ONCE() annotations
and run locklessly.
rtnl_proto_down_size() should assume worst case,
because readng dev->proto_down_reason multiple
times would be racy without RTNL in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the following patch we want to read dev->allmulti
and dev->promiscuity locklessly from rtnl_fill_ifinfo()
In this patch I change __dev_set_promiscuity() and
__dev_set_allmulti() to write these fields (and dev->flags)
only if they succeed, with WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
rtnl_fill_ifinfo() can read dev->tx_queue_len locklessly,
granted we add corresponding READ_ONCE()/WRITE_ONCE() annotations.
Add missing READ_ONCE(dev->tx_queue_len) in teql_enqueue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We can use netdev_copy_name() to no longer rely on RTNL
to fetch dev->name.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev->qdisc can be read using RCU protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
says:
====================
net: qede: don't restrict error codes
This series fixes the qede driver, so that when a helper function fails,
then the callee should return the returned error code, instead just
assuming that the error is eg. -EINVAL.
The patches in this series, reduces the change of future bugs, so new
error codes can be returned from the helpers, without having to update
the call sites.
This is a follow-up to my recent series "net: qede: avoid overruling
error codes", which fixed the cases where the implicit assumption of
failing with specific error codes had been broken.
https://lore.kernel.org/netdev/20240426091227.78060-1-ast@fiberby.net/
Asbjørn Sloth Tønnesen (3):
net: qede: use return from qede_parse_actions() for flow_spec
net: qede: use return from qede_flow_spec_validate_unused()
net: qede: use return from qede_flow_parse_ports()
.../net/ethernet/qlogic/qede/qede_filter.c | 27 ++++++++++++-------
1 file changed, 18 insertions(+), 9 deletions(-)
====================
Link: https://lore.kernel.org/r/20240503105505.839342-1-ast@fiberby.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling qede_flow_parse_ports(), then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_flow_parse_ports() can currently fail with:
* -EINVAL
This patch changes qede_flow_parse_v{4,6}_common() to
use the actual return code from qede_flow_parse_ports(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling qede_flow_spec_validate_unused() then
the return code was only used for a non-zero check,
and then -EOPNOTSUPP was returned.
qede_flow_spec_validate_unused() can currently fail with:
* -EOPNOTSUPP
This patch changes qede_flow_spec_to_rule() to use the
actual return code from qede_flow_spec_validate_unused(),
so it's no longer assumed that all errors are -EOPNOTSUPP.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In qede_flow_spec_to_rule(), when calling
qede_parse_actions() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
Commit 319a1d1947 ("flow_offload: check for
basic action hw stats type") broke the implicit
assumption that it could only fail with -EINVAL,
by changing it to return -EOPNOTSUPP, when hardware
stats are requested.
However AFAICT it's not possible to trigger
qede_parse_actions() to return -EOPNOTSUPP, when
called from qede_flow_spec_to_rule(), as hardware
stats can't be requested by ethtool_rx_flow_rule_create().
This patch changes qede_flow_spec_to_rule() to use
the actual return code from qede_parse_actions(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
