These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240502074722.1103986-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
On the STM32F4/7, the MOSI and CLK pins float while the controller is
disabled. CS is a regular GPIO, and therefore always driven. Currently,
the controller is enabled in the transfer_one() callback, which runs
after CS is asserted. Therefore, there is a period where the SPI pins
are floating while CS is asserted, making it possible for stray signals
to disrupt communications. An analogous problem occurs at the end of the
transfer when the controller is disabled before CS is released.
This problem can be reliably observed by enabling the pull-up (if
CPOL=0) or pull-down (if CPOL=1) on the clock pin. This will cause two
extra unintended clock edges per transfer, when the controller is
enabled and disabled.
Note that this bug is likely not present on the STM32H7, because this
driver sets the AFCNTR bit (not supported on F4/F7), which keeps the SPI
pins driven even while the controller is disabled.
Enabling/disabling the controller as part of runtime PM was suggested as
an alternative approach, but this breaks the driver on the STM32MP1 (see
[1]). The following quote from the manual may explain this:
> To restart the internal state machine properly, SPI is strongly
> suggested to be disabled and re-enabled before next transaction starts
> despite its setting is not changed.
This patch has been tested on an STM32F746 with a MAX14830 UART
expander.
[1] https://lore.kernel.org/lkml/ZXzRi_h2AMqEhMVw@dell-precision-5540/T/
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Link: https://lore.kernel.org/r/20240424135237.1329001-2-ben.wolsieffer@hefring.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP pin configuration varies based on acp version.
ACP PCI driver should read the ACP PIN config value and based on config
value, it has to create a platform device in below two conditions.
1) If ACP PDM configuration is selected from BIOS and ACP PDM controller
exists.
2) If ACP I2S configuration is selected from BIOS.
Other than above scenarios, ACP PCI driver should skip the platform
device creation logic, i.e. ACP PCI driver probe sequence should never
fail if other acp pin configuration is selected. It should skip platform
device creation logic.
check_acp_pdm() function was implemented for ACP6.x platforms to check
ACP PDM configuration. Previously, this code was safe guarded by
FLAG_AMD_LEGACY_ONLY_DMIC flag check.
This implementation breaks audio use cases for Huawei Matebooks which are
based on ACP3.x varaint uses I2S configuration.
In current scenario, check_acp_pdm() function returns -ENODEV value
which results in ACP PCI driver probe failure without creating a platform
device even in case of valid ACP pin configuration.
Implement check_acp_config() as a common function which invokes platform
specific acp pin configuration check functions for ACP3.x, ACP6.0 & ACP6.3
& ACP7.0 variants and checks for ACP PDM controller.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218780
Fixes: 4af565de9f ("ASoC: amd: acp: fix for acp pdm configuration check")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20240502140340.4049021-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Detect packets with ip_summed CHECKSUM_PARTIAL and skip these. These
should not exist, as the test sends individual packets between two
hosts. But if (HW) GRO is on, with randomized content sometimes
subsequent packets can be coalesced.
In this case the GSO packet checksum is converted to a pseudo checksum
in anticipation of sending out as TSO/USO. So the field will not match
the expected value.
Do not count these as test errors.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20240501193156.3627344-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're a bit too loose with error checking for background
processes. cmd() completely ignores the fail argument
passed to the constructor if background is True.
Default to checking for errors if process is not terminated
explicitly. Caller can override with True / False.
For bkg() the processing step is called magically by __exit__
so record the value passed in the constructor.
Reported-by: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20240502025325.1924923-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct hfi1_netdev_rx by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at hfi1_alloc_rx().
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Leon Romanovsky <leon@kernel.org>
Link: https://lore.kernel.org/r/20240430162213.746492-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use flow_rule_is_supp_control_flags() to reject filters
with unsupported control flags.
In case any unsupported control flags are masked,
flow_rule_is_supp_control_flags() sets a NL extended
error message, and we return -EOPNOTSUPP.
Remove FLOW_DIS_FIRST_FRAG specific error message,
and treat it as any other unsupported control flag.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240422152728.175677-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix for a backmerge going slightly wrong.
- An UAF fix
- Avoid a WA error on LNL.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRskUM7w1oG5rx2IZO4FpNVCsYGvwUCZjOh4wAKCRC4FpNVCsYG
v4TfAP9ngQQrvAvNm6Gp8oWVzdqt3Q2uswvDIwfQXylb9dJcJwEAyRwpyEclhIkN
xrsHdNTSH0fnC9xzxPjUddGyQokzRQs=
=VGIW
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-next-fixes-2024-05-02' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver Changes:
- Fix for a backmerge going slightly wrong.
- An UAF fix
- Avoid a WA error on LNL.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZjOijQA43zhu3SZ4@fedora
In bdev_alloc() we have all flags initialized to false, so
assignment to ->bh_has_submit_bio n there is a no-op unless
we have partno != 0 and flag already set on entire device.
In device_add_disk() we have just allocated the block_device
in question and it had been a full-device one, so the flag
is guaranteed to be still clear when we get to assignment.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Replace bd_partno with a 32bit field (__bd_flags). The lower 8 bits
contain the partition number, the upper 24 are for flags.
Helpers: bdev_{test,set,clear}_flag(bdev, flag), with atomic_or()
and atomic_andnot() used to set/clear.
NOTE: this commit does not actually move any flags over there - they
are still bool fields. As the result, it shifts the fields wrt
cacheline boundaries; that's going to be restored once the first
3 flags are dealt with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add INT_MAX check to ring_buffer__consume_n(). We do the similar check
to handle int return result of all these ring buffer APIs in other APIs
and ring_buffer__consume_n() is missing one. This patch fixes this
omission.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20240430201952.888293-2-andrii@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
ringbuf_process_ring() return int64_t, while ring__consume_n() assigns
it to int. It's highly unlikely, but possible for ringbuf_process_ring()
to return value larger than INT_MAX, so use int64_t. ring__consume_n()
does check INT_MAX before returning int result to the user.
Fixes: 4d22ea94ea ("libbpf: Add ring__consume_n / ring_buffer__consume_n")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20240430201952.888293-1-andrii@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Miao Xu says:
====================
This patchset attempts to add two new arguments into the hookpoint
cong_control in tcp_congestion_ops. The new arguments are inherited
from the caller tcp_cong_control and can be used by any bpf cc prog
that implements its own logic inside this hookpoint.
Please review. Thanks a lot!
Changelog
=====
v2->v3:
- Fixed the broken selftest caused by the new arguments.
- Renamed the selftest file name and bpf prog name.
v1->v2:
- Split the patchset into 3 separate patches.
- Added highlights in the selftest prog.
- Removed the dependency on bpf_tcp_helpers.h.
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch adds a selftest to show the usage of the new arguments in
cong_control. For simplicity's sake, the testing example reuses cubic's
kernel functions.
Signed-off-by: Miao Xu <miaxu@meta.com>
Link: https://lore.kernel.org/r/20240502042318.801932-4-miaxu@meta.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch allows the write of tp->snd_cwnd_stamp in a bpf tcp
ca program. An use case of writing this field is to keep track
of the time whenever tp->snd_cwnd is raised or reduced inside
the `cong_control` callback.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Miao Xu <miaxu@meta.com>
Link: https://lore.kernel.org/r/20240502042318.801932-3-miaxu@meta.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch adds two new arguments for cong_control of struct
tcp_congestion_ops:
- ack
- flag
These two arguments are inherited from the caller tcp_cong_control in
tcp_intput.c. One use case of them is to update cwnd and pacing rate
inside cong_control based on the info they provide. For example, the
flag can be used to decide if it is the right time to raise or reduce a
sender's cwnd.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Miao Xu <miaxu@meta.com>
Link: https://lore.kernel.org/r/20240502042318.801932-2-miaxu@meta.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Explicitly require KVM_CAP_USER_MEMORY2 for selftests that create memslots,
i.e. skip selftests that need memslots instead of letting them fail on
KVM_SET_USER_MEMORY_REGION2. While it's ok to take a dependency on new
kernel features, selftests should skip gracefully instead of failing hard
when run on older kernels.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/69ae0694-8ca3-402c-b864-99b500b24f5d@moroto.mountain
Suggested-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240430162133.337541-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
The rseq test's migration worker delays 1-10 us, assuming that one KVM_RUN
iteration only takes a few microseconds. But if the CPU low power wakeup
latency is large enough, for example, hundreds or even thousands of
microseconds for deep C-state exit latencies on x86 server CPUs, it may
happen that the target CPU is unable to wakeup and run the vCPU before the
migration worker starts to migrate the vCPU thread to the _next_ CPU.
If the system workload is light, most CPUs could be at a certain low
power state, which may result in less successful migrations and fail the
migration/KVM_RUN ratio sanity check. But this is not supposed to be
deemed a test failure.
Add a command line option to skip the sanity check, along with a comment
and a verbose assert message to try to help the user resolve the potential
source of failures without having to resort to disabling the check.
Co-developed-by: Dongsheng Zhang <dongsheng.x.zhang@intel.com>
Signed-off-by: Dongsheng Zhang <dongsheng.x.zhang@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Link: https://lore.kernel.org/r/20240502213936.27619-1-zide.chen@intel.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Jordan Rife says:
====================
This patch series adds test coverage for BPF sockaddr hooks and their
interactions with kernel socket functions (i.e. kernel_bind(),
kernel_connect(), kernel_sendmsg(), sock_sendmsg(),
kernel_getpeername(), and kernel_getsockname()) while also rounding out
IPv4 and IPv6 sockaddr hook coverage in prog_tests/sock_addr.c.
As with v1 of this patch series, we add regression coverage for the
issues addressed by these patches,
- commit 0bdf399342c5("net: Avoid address overwrite in kernel_connect")
- commit 86a7e0b69bd5("net: prevent rewrite of msg_name in sock_sendmsg()")
- commit c889a99a21bf("net: prevent address rewrite in kernel_bind()")
- commit 01b2885d9415("net: Save and restore msg_namelen in sock_sendmsg")
but broaden the focus a bit.
In order to extend prog_tests/sock_addr.c to test these kernel
functions, we add a set of new kfuncs that wrap individual socket
operations to bpf_testmod and invoke them through set of corresponding
SYSCALL programs (progs/sock_addr_kern.c). Each test case can be
configured to use a different set of "sock_ops" depending on whether it
is testing kernel calls (kernel_bind(), kernel_connect(), etc.) or
system calls (bind(), connect(), etc.).
=======
Patches
=======
* Patch 1 fixes the sock_addr bind test program to work for big endian
architectures such as s390x.
* Patch 2 introduces the new kfuncs to bpf_testmod.
* Patch 3 introduces the BPF program which allows us to invoke these
kfuncs invividually from the test program.
* Patch 4 lays the groundwork for IPv4 and IPv6 sockaddr hook coverage
by migrating much of the environment setup logic from
bpf/test_sock_addr.sh into prog_tests/sock_addr.c and moves test cases
to cover bind4/6, connect4/6, sendmsg4/6 and recvmsg4/6 hooks.
* Patch 5 makes the set of socket operations for each test case
configurable, laying the groundwork for Patch 6.
* Patch 6 introduces two sets of sock_ops that invoke the kernel
equivalents of connect(), bind(), etc. and uses these to add coverage
for the kernel socket functions.
=======
Changes
=======
v2->v3
------
* Renamed bind helpers. Dropped "_ntoh" suffix.
* Added guards to kfuncs to make sure addrlen and msglen do not exceed
the buffer capacity.
* Added KF_SLEEPABLE flag to kfuncs.
* Added a mutex (sock_lock) to kfuncs to serialize access to sock.
* Added NULL check for sock to each kfunc.
* Use the "sock_addr" networking namespace for all network interface
setup and testing.
* Use "nodad" when calling "ip -6 addr add" during interface setup to
avoid delays and remove ping loop.
* Removed test cases from test_sock_addr.c to make it clear what remains
to be migrated.
* Removed unused parameter (expect_change) from sock_addr_op().
Link: https://lore.kernel.org/bpf/20240412165230.2009746-1-jrife@google.com/T/#u
v1->v2
------
* Dropped test_progs/sock_addr_kern.c and the sock_addr_kern test module
in favor of simply expanding bpf_testmod and test_progs/sock_addr.c.
* Migrated environment setup logic from bpf/test_sock_addr.sh into
prog_tests/sock_addr.c rather than invoking the script from the test
program.
* Added kfuncs to bpf_testmod as well as the sock_addr_kern BPF program
to enable us to invoke kernel socket functions from
test_progs/sock_addr.c.
* Added test coverage for kernel socket functions to
test_progs/sock_addr.c.
Link: https://lore.kernel.org/bpf/20240329191907.1808635-1-jrife@google.com/T/#u
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch creates two sets of sock_ops that call out to the SYSCALL
hooks in the sock_addr_kern BPF program and uses them to construct
test cases for the range of supported operations (kernel_connect(),
kernel_bind(), kernel_sendms(), sock_sendmsg(), kernel_getsockname(),
kenel_getpeername()). This ensures that these interact with BPF sockaddr
hooks as intended.
Beyond this it also ensures that these operations do not modify their
address parameter, providing regression coverage for the issues
addressed by this set of patches:
- commit 0bdf399342c5("net: Avoid address overwrite in kernel_connect")
- commit 86a7e0b69bd5("net: prevent rewrite of msg_name in sock_sendmsg()")
- commit c889a99a21bf("net: prevent address rewrite in kernel_bind()")
- commit 01b2885d9415("net: Save and restore msg_namelen in sock_sendmsg")
Signed-off-by: Jordan Rife <jrife@google.com>
Link: https://lore.kernel.org/r/20240429214529.2644801-7-jrife@google.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
In order to reuse the same test code for both socket system calls (e.g.
connect(), bind(), etc.) and kernel socket functions (e.g.
kernel_connect(), kernel_bind(), etc.), this patch introduces the "ops"
field to sock_addr_test. This field allows each test cases to configure
the set of functions used in the test case to create, manipulate, and
tear down a socket.
Signed-off-by: Jordan Rife <jrife@google.com>
Link: https://lore.kernel.org/r/20240429214529.2644801-6-jrife@google.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This patch lays the groundwork for testing IPv4 and IPv6 sockaddr hooks
and their interaction with both socket syscalls and kernel functions
(e.g. kernel_connect, kernel_bind, etc.). It moves some of the test
cases from the old-style bpf/test_sock_addr.c self test into the
sock_addr prog_test in a step towards fully retiring
bpf/test_sock_addr.c. We will expand the test dimensions in the
sock_addr prog_test in a later patch series in order to migrate the
remaining test cases.
Signed-off-by: Jordan Rife <jrife@google.com>
Link: https://lore.kernel.org/r/20240429214529.2644801-5-jrife@google.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Return -ENOMEM from of_pci_prop_intr_map() if kcalloc() fails to prevent a
NULL pointer dereference in this case.
Fixes: 407d1a5192 ("PCI: Create device tree node for bridge")
Link: https://lore.kernel.org/r/20240303105729.78624-1-duoming@zju.edu.cn
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With only one set of defines remaining, state can be almost used as-is to
set ->aspm_disable/default. Only CLKPM and L1 PM substates need special
handling.
Remove unnecessary if conditions that can use the state variable bits
directly. Move ASPM mask calculation into pci_calc_aspm_enable_mask() and
pci_calc_aspm_disable_mask() helpers which makes it easier to alter state
variable directly.
Link: https://lore.kernel.org/r/20240322123952.6384-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The linux/pci.h and aspm.c files define their own sets of link state
related defines which are almost the same.
Consolidate the use of defines into those defined by linux/pci.h and expand
PCIE_LINK_STATE_L0S to match earlier ASPM_STATE_L0S that includes both
upstream and downstream bits. Rename also the defines that are internal to
aspm.c to start with PCIE_LINK_STATE for consistency.
While the PCIE_LINK_STATE_L0S BIT(0) -> (BIT(0) | BIT(1)) transformation is
not 1:1, in practice aspm.c already used ASPM_STATE_L0S that has both bits
enabled except during mapping.
While at it, place the PCIE_LINK_STATE_CLKPM define last to have more
logical grouping.
Use static_assert() to ensure PCIE_LINK_STATE_L0S is strictly equal to the
combination of PCIE_LINK_STATE_L0S_UP/DW.
Link: https://lore.kernel.org/r/20240322123952.6384-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Is is reported that for dm-raid10, lvextend + lvchange --syncaction will
trigger following softlockup:
kernel:watchdog: BUG: soft lockup - CPU#3 stuck for 26s! [mdX_resync:6976]
CPU: 7 PID: 3588 Comm: mdX_resync Kdump: loaded Not tainted 6.9.0-rc4-next-20240419 #1
RIP: 0010:_raw_spin_unlock_irq+0x13/0x30
Call Trace:
<TASK>
md_bitmap_start_sync+0x6b/0xf0
raid10_sync_request+0x25c/0x1b40 [raid10]
md_do_sync+0x64b/0x1020
md_thread+0xa7/0x170
kthread+0xcf/0x100
ret_from_fork+0x30/0x50
ret_from_fork_asm+0x1a/0x30
And the detailed process is as follows:
md_do_sync
j = mddev->resync_min
while (j < max_sectors)
sectors = raid10_sync_request(mddev, j, &skipped)
if (!md_bitmap_start_sync(..., &sync_blocks))
// md_bitmap_start_sync set sync_blocks to 0
return sync_blocks + sectors_skippe;
// sectors = 0;
j += sectors;
// j never change
Root cause is that commit 301867b1c1 ("md/raid10: check
slab-out-of-bounds in md_bitmap_get_counter") return early from
md_bitmap_get_counter(), without setting returned blocks.
Fix this problem by always set returned blocks from
md_bitmap_get_counter"(), as it used to be.
Noted that this patch just fix the softlockup problem in kernel, the
case that bitmap size doesn't match array size still need to be fixed.
Fixes: 301867b1c1 ("md/raid10: check slab-out-of-bounds in md_bitmap_get_counter")
Reported-and-tested-by: Nigel Croxon <ncroxon@redhat.com>
Closes: https://lore.kernel.org/all/71ba5272-ab07-43ba-8232-d2da642acb4e@redhat.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240422065824.2516-1-yukuai1@huaweicloud.com
Signed-off-by: Song Liu <song@kernel.org>
This reverts commit 8a91b29f1f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426122259.46808-1-luca.ceresoli@bootlin.com
(cherry picked from commit 2940ee03b2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
btrfs_get_bdev_and_sb() has two callers - btrfs_open_one_device(),
which asks for open to be exclusive and btrfs_get_dev_args_from_path(),
which doesn't. Currently it does set_blocksize() in all cases.
I'm rather dubious about the need to do set_blocksize() anywhere in btrfs,
to be honest - there's some access to page cache of underlying block
devices in there, but it's nowhere near the hot paths, AFAICT.
In any case, btrfs_get_dev_args_from_path() only needs to read
the on-disk superblock and copy several fields out of it; all
callers are only interested in devices that are already opened
and brought into per-filesystem set, so setting the block size
is redundant for those and actively harmful if we are given
a pathname of unrelated device.
So we only need btrfs_get_bdev_and_sb() to call set_blocksize()
when it's asked to open exclusive.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
same as with the swap...
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
plane->state and plane->state->fb can be NULL, so add a check before
dereferencing them.
Found by testing with the imx driver.
Fixes: 879b3b6511 ("drm/fb_dma: Add generic get_scanout_buffer() for drm_panic")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426121121.241366-1-jfalempe@redhat.com
(cherry picked from commit 986c12d8c9)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Framebuffer memory is allocated via vzalloc() from non-contiguous
physical pages. The physical framebuffer start address is therefore
meaningless. Do not set it.
The value is not used within the kernel and only exported to userspace
on dedicated ARM configs. No functional change is expected.
v2:
- refer to vzalloc() in commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: a5b44c4adb ("drm/fbdev-generic: Always use shadow buffering")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Zack Rusin <zackr@vmware.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: <stable@vger.kernel.org> # v6.4+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Zack Rusin <zack.rusin@broadcom.com>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Tested-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240419083331.7761-2-tzimmermann@suse.de
(cherry picked from commit 73ef0aecba)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
