Newer Qualcomm platforms (sm8450+) successfully handle busy state and
send the Command Completion after sending the Busy state. Older devices
have firmware bug and can not continue after sending the CCI_BUSY state,
but the command that leads to CCI_BUSY is already forbidden by the
NO_PARTNER_PDOS quirk.
Follow other UCSI glue drivers and drop special handling for CCI_BUSY
event. Let the UCSI core properly handle this state.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-3-716c145ca4b1@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm SM8550 (and via a fallback compat SM8650) firmware properly
handles the GET_PDOS command, it sends the CCI_BUSY notification,
and then follows with the CCI_COMMAND_COMPLETE event. Stop using the quirk
for those two platforms.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-2-716c145ca4b1@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various Rockchip embedded audio codecs are only present on Rockchip
SoCs. Hence add dependencies on ARCH_ROCKCHIP, to prevent asking the
user about these drivers when configuring a kernel without Rockchip SoC
support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://msgid.link/r/6cdbaf4afcf4d2059b257f6cb3a8a61bf5e17688.1712676714.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The PPM might take time to process a reset. Allow 20ms for the reset to
be processed before reading the CCI.
This should not slow down existing implementations because they would
not set any bits in the CCI after a reset, and would take a 20ms delay
to read the CCI anyway. This change makes the delay explicit, and
reduces a CCI read. Based on the spec, the PPM has 10ms to set busy, so,
20ms seems like a reasonable delay before we read the CCI.
Signed-off-by: Pavan Holla <pholla@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240409-ucsi-reset-delay-v3-1-8440710b012b@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.
Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.
Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ci_usb_phy_init is already handling the
hw_phymode_configure path which is also only possible after we have
a valid phy. So we move the ci_ulpi_init after the phy initialization
to be really sure to be able to communicate with the ulpi phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240328-chipidea-phy-misc-v1-1-907d9de5d4df@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is expected that the USB controller works in host mode
to have the USB hub operational.
Remove such unneeded property from the devicetree example.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240405195051.945474-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the Microchip USB2412, USB2417, and USB2514 USB hubs.
The existing usb251xb.yaml describes Microchip USB251x hubs that are
connected under I2C bus. Here, the hub is under the USB bus and use
the on-board-hub interface instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240405120147.880933-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After pulling the reset pin some phys are not immediately ready. We add
a short delay of at least 10 ms to ensure that the phy can be properly
used.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240402-phy-misc-v1-1-de5c17f93f17@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove uses of deprecated page APIs, and move the check for large
folios to here to avoid taking the folio lock if the folio is too large.
We could do better here by attempting to split the large folio, but I'll
leave that improvement for someone who can test it.
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20240322161149.2327518-3-willy@infradead.org
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
These page APIs are deprecated, so convert the incoming page to a folio
and use the folio APIs instead. The ultravisor API cannot handle large
folios, so return -EINVAL if one has slipped through.
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20240322161149.2327518-2-willy@infradead.org
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The CPU Measurement facility crypto counter set functionality
is defined by the Second Counter Version Number. This number
varies between machine types, but is upward compatible.
Lessen the checks to reflect this behavior.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Common pattern in non-verbose build output for quiet commands is that the
shorthand of a command including whitespace contains at least eight
characters. Adjust this for the RELOCS command, which comes only with seven
characters.
Before:
SORTTAB vmlinux
CC arch/s390/boot/version.o
RELOCS arch/s390/boot/relocs.S
OBJCOPY arch/s390/boot/info.bin
After:
SORTTAB vmlinux
CC arch/s390/boot/version.o
RELOCS arch/s390/boot/relocs.S
OBJCOPY arch/s390/boot/info.bin
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended.
Cc: Vineeth Vijayan <vneethv@linux.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Link: https://lore.kernel.org/r/20240314095209.1325229-1-lizhijian@fujitsu.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The configuration option ZCRYPT_DEBUG is used only in ap queue code,
so rename it to AP_DEBUG. It also no longer depends on ZCRYPT but on
AP. While at it, also update the help text.
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
There is no hard requirement to have the ap bus statically in the
kernel, so add an option to compile it as module.
Cc: Tony Krowiak <akrowiak@linux.ibm.com>
Cc: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Anthony Krowiak <akrowiak@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The direct dependency of chsc and the AP bus prevents the
modularization of ap bus. Introduce a notifier interface for AP
changes, which decouples the producer of the change events (chsc) from
the consumer (ap_bus).
Remove the ap_cfg_chg() interface and replace it with the notifier
invocation. The ap bus module registers a notification handler, which
triggers the AP bus scan.
Cc: Vineeth Vijayan <vneethv@linux.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The inline function is_prot_virt_guest() in asm/uv.h makes use of the
prot_virt_guest symbol. As this inline function can be called by other
parts of the kernel (modules and built-in), the symbol should be
exported, similar to the prot_virt_host symbol.
One consumer of is_prot_virt_guest() will be the ap bus code.
Cc: Janosch Frank <frankja@linux.ibm.com>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The IRQ handler may rely on the bus or the root device. Register the
adapter IRQ after setting up the bus and the root device to avoid any
race conditions.
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Rework the ap initialization and add missing cleanups to the error path.
Errors during the registration of IRQ handler is now also detected.
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Since qci is available on most of the current machines, move away from
the dynamic buffers for qci information and store it instead in a
statically defined buffer.
The new flags member in struct ap_config_info is now used as an
indicator, if qci is available in the system (at least one of these
bits is set).
Suggested-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
The ChipID bytes are read in inverse order: invert the ChipID value
defined as IT5205FN_CHIP_ID and used for validating the same.
Fixes: 41fe9ea169 ("usb: typec: mux: Add ITE IT5205 Alternate Mode Passive MUX driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240409113646.305105-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending a patch to (among others) Li Yang the nxp MTA replied that
the address doesn't exist and so the mail couldn't be delivered. The
error code was 550, so at least technically that's not a temporal issue.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240405072042.697182-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a small helper to compute the set of pipes that the current
crtc is using.
And we have at least one trivial place in
intel_ddi_update_active_dpll() where we can use it
immediately, so let's do that.
v2: Use the name 'pipe_crtc' for the per-pipe crtc pointer
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-12-ville.syrjala@linux.intel.com
Pass the connector explicitly to intel_dp_need_bigjoiner()
so that it'll actually check the correct place for the
bigjoiner force flag.
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-11-ville.syrjala@linux.intel.com
intel_dp_mst_compute_config() is missing the "does the
joiner need DSC?" check despite claiming to have a lot
of other joiner/dsc stuff in there (albeit disabled).
Replicate the logic from the SST side.
TODO: refactor all this duplicated code!
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-10-ville.syrjala@linux.intel.com
The MT6360 regulator binding, the example in the MT6360 mfd binding, and
the devicetree users of those bindings are rightfully declaring MT6360
regulator subnodes with non-capital names, and luckily without using the
deprecated regulator-compatible property.
With this driver declaring capitalized BUCKx/LDOx as of_match string for
the node names, obviously no regulator gets probed: fix that by changing
the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets
assigned to the of_match.
Fixes: d321571d5e ("regulator: mt6360: Add support for MT6360 regulator")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case that no RTS GPIO is available do not use a dedicated nullified
serial_rs485 struct to disable RS485 support, but simply delete the
SER_RS485_ENABLED flag in the ports rs485_supported struct.
This make the structure superfluous and it can be removed.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core already checks the RS485 RTS settings for sanity, so remove
the superfluous check in serial8250_em485_config().
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable dmacr is only used if DMA is enabled, so move it into the
CONFIG_DMA_ENGINE conditional.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to earlier code changes function pl011_get_rs485_mode() is now merely
a wrapper for uart_get_rs485_mode() which does not add any further
functionality. So remove it and instead call uart_get_rs485_mode()
directly.
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that while the QSEECOM APP_SEND command has specific fields
for request and response buffers, uefisecapp expects them both to be in
a single memory region. Failure to adhere to this has (so far) resulted
in either no response being written to the response buffer (causing an
EIO to be emitted down the line), the SCM call to fail with EINVAL
(i.e., directly from TZ/firmware), or the device to be hard-reset.
While this issue can be triggered deterministically, in the current form
it seems to happen rather sporadically (which is why it has gone
unnoticed during earlier testing). This is likely due to the two
kzalloc() calls (for request and response) being directly after each
other. Which means that those likely return consecutive regions most of
the time, especially when not much else is going on in the system.
Fix this by allocating a single memory region for both request and
response buffers, properly aligning both structs inside it. This
unfortunately also means that the qcom_scm_qseecom_app_send() interface
needs to be restructured, as it should no longer map the DMA regions
separately. Therefore, move the responsibility of DMA allocation (or
mapping) to the caller.
Fixes: 759e7a2b62 ("firmware: Add support for Qualcomm UEFI Secure Application")
Cc: stable@vger.kernel.org # 6.7
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # X13s
Link: https://lore.kernel.org/r/20240406130125.1047436-1-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Instead of using container_of() explicitly, introduce a helper macro.
This saves a lot of lines of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409144721.638326-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_ALIAS() in most cases is a pure hack to avoid placing ID tables.
Replace it with the respective ID tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct uart_port has a copy of the IRQ that is also stored
in the private data structure. Remove the duplication in the latter
one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the vibrator connected to PM8941 found on the Sony shinano
platform.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240406-shinano-vib-v1-1-fdd02af39d56@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
gcc -Wstringop-truncation warns about copying a string that results in a
missing nul termination:
drivers/acpi/acpica/tbfind.c: In function 'acpi_tb_find_table':
drivers/acpi/acpica/tbfind.c:60:9: error: 'strncpy' specified bound 6 equals destination size [-Werror=stringop-truncation]
60 | strncpy(header.oem_id, oem_id, ACPI_OEM_ID_SIZE);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/acpi/acpica/tbfind.c:61:9: error: 'strncpy' specified bound 8 equals destination size [-Werror=stringop-truncation]
61 | strncpy(header.oem_table_id, oem_table_id, ACPI_OEM_TABLE_ID_SIZE);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The code works as intended, and the warning could be addressed by using
a memcpy(), but turning the warning off for this file works equally well
and may be easier to merge.
Fixes: 47c08729bf ("ACPICA: Fix for LoadTable operator, input strings")
Link: https://lore.kernel.org/lkml/CAJZ5v0hoUfv54KW7y4223Mn9E7D4xvR7whRFNLTBqCZMUxT50Q@mail.gmail.com/#t
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The circular buffer is NULLified in uart_tty_port_shutdown()
under the spin lock. However, the PM or other timer based callbacks
may still trigger after this event without knowning that buffer pointer
is not valid. Since the serial code is a bit inconsistent in checking
the buffer state (some rely on the head-tail positions, some on the
buffer pointer), it's better to have both aligned, i.e. buffer pointer
to be NULL and head-tail possitions to be the same, meaning it's empty.
This will prevent asynchronous calls to dereference NULL pointer as
reported recently in 8250 case:
BUG: kernel NULL pointer dereference, address: 00000cf5
Workqueue: pm pm_runtime_work
EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
...
? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
__start_tx (drivers/tty/serial/8250/8250_port.c:1551)
serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654)
serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63)
__rpm_callback (drivers/base/power/runtime.c:393)
? serial_port_remove (drivers/tty/serial/serial_port.c:50)
rpm_suspend (drivers/base/power/runtime.c:447)
The proposed change will prevent ->start_tx() to be called during
suspend on shut down port.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404031607.2e92eebe-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240404150034.41648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>