The WL-355608-A8 is a 3.5" 640x480@60Hz RGB LCD display from an unknown
OEM used in a number of handheld gaming devices made by Anbernic.
Previously committed using the OEM serial without a vendor prefix,
however following subsequent discussion the preference is to use the
integrating device vendor and name where the OEM is unknown.
There are 4 RG35XX series devices from Anbernic based on an Allwinner
H700 SoC using this panel, with the -Plus variant introduced first.
Therefore the -Plus is used as the fallback for the subsequent -H,
-2024, and -SP devices.
Alter the filename and compatible string to reflect the convention.
Fixes: 45b888a898 ("dt-bindings: display: panel: Add WL-355608-A8 panel")
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240904012456.35429-2-ryan@testtoast.com
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects. Although
that is not the case here, it is seems best to use ';' unless ',' is
intended.
Found by inspection. No functional change intended. Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240905024245.1642989-1-nichen@iscas.ac.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We were allowing any users to create a high priority group without any
permission checks. As a result, this was allowing possible denial of
service.
We now only allow the DRM master or users with the CAP_SYS_NICE
capability to set higher priorities than PANTHOR_GROUP_PRIORITY_MEDIUM.
As the sole user of that uAPI lives in Mesa and hardcode a value of
MEDIUM [1], this should be safe to do.
Additionally, as those checks are performed at the ioctl level,
panthor_group_create now only check for priority level validity.
[1]f390835074/src/gallium/drivers/panfrost/pan_csf.c (L1038)
Signed-off-by: Mary Guillemard <mary.guillemard@collabora.com>
Fixes: de85488138 ("drm/panthor: Add the scheduler logical block")
Cc: stable@vger.kernel.org
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240903144955.144278-2-mary.guillemard@collabora.com
commit 9636be85cc ("x86/hyperv: Fix hyperv_pcpu_input_arg handling when
CPUs go online/offline") introduces a new cpuhp state for hyperv
initialization.
cpuhp_setup_state() returns the state number if state is
CPUHP_AP_ONLINE_DYN or CPUHP_BP_PREPARE_DYN and 0 for all other states.
For the hyperv case, since a new cpuhp state was introduced it would
return 0. However, in hv_machine_shutdown(), the cpuhp_remove_state() call
is conditioned upon "hyperv_init_cpuhp > 0". This will never be true and
so hv_cpu_die() won't be called on all CPUs. This means the VP assist page
won't be reset. When the kexec kernel tries to setup the VP assist page
again, the hypervisor corrupts the memory region of the old VP assist page
causing a panic in case the kexec kernel is using that memory elsewhere.
This was originally fixed in commit dfe94d4086 ("x86/hyperv: Fix kexec
panic/hang issues").
Get rid of hyperv_init_cpuhp entirely since we are no longer using a
dynamic cpuhp state and use CPUHP_AP_HYPERV_ONLINE directly with
cpuhp_remove_state().
Cc: stable@vger.kernel.org
Fixes: 9636be85cc ("x86/hyperv: Fix hyperv_pcpu_input_arg handling when CPUs go online/offline")
Signed-off-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240828112158.3538342-1-anirudh@anirudhrb.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240828112158.3538342-1-anirudh@anirudhrb.com>
Drop the undocumented amlogic,meson-gxlx-saradc compatible by dropping the
compatible override, and fix the following DTBs check:
/soc/bus@c1100000/adc@8680: failed to match any schema with compatible: ['amlogic,meson-gxlx-saradc', 'amlogic,meson-saradc']
Fixes: f6386b5afa ("arm64: dts: meson: add GXLX/S905L/p271 support")
Link: https://lore.kernel.org/r/20240905-topic-amlogic-upstream-gxlx-drop-iio-compat-v2-1-7a690eb95bc2@linaro.org
[narmstrong: fix commit message]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Because the loop-expression will do one more time before getting false from
cond-expression, the original code copied one more entry size beyond valid
region.
Fix it by moving the entry copy to loop-body.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240902015803.20420-1-pkshih@realtek.com
To get more accurate RSSI, this commit includes frequency domain RSSI
info in RSSI calculation. Add correspond physts parsing and macro to
get frequency domain RSSI information for supported IC.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240828055217.10263-3-pkshih@realtek.com
Use RSSI without subtracting offset as packet detection lower bound and
set an absolute minimal threshold. It's equivalent to setting a higher
noise floor, thereby reducing false alarm and improving interference
endurance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240828055217.10263-2-pkshih@realtek.com
Tony Nguyen says:
====================
ice: fix synchronization between .ndo_bpf() and reset
Larysa Zaremba says:
PF reset can be triggered asynchronously, by tx_timeout or by a user. With some
unfortunate timings both ice_vsi_rebuild() and .ndo_bpf will try to access and
modify XDP rings at the same time, causing system crash.
The first patch factors out rtnl-locked code from VSI rebuild code to avoid
deadlock. The following changes lock rebuild and .ndo_bpf() critical sections
with an internal mutex as well and provide complementary fixes.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: do not bring the VSI up, if it was down before the XDP setup
ice: remove ICE_CFG_BUSY locking from AF_XDP code
ice: check ICE_VSI_DOWN under rtnl_lock when preparing for reset
ice: check for XDP rings instead of bpf program when unconfiguring
ice: protect XDP configuration with a mutex
ice: move netif_queue_set_napi to rtnl-protected sections
====================
Link: https://patch.msgid.link/20240903183034.3530411-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mwifiex has recently started to see active development which is good
news. rtw89 is also under active development and got several new
features. Otherwise not really anything out of ordinary.
We have one conflict in ath12k but that's easy to fix:
https://lore.kernel.org/all/20240808104348.6846e064@canb.auug.org.au/
Major changes:
mwifiex
* support for up to ten Authentication and Key Management (AKM) suites
* host MAC Sublayer Management Entity (MLME) client and AP mode support
* WPA-PSK-SHA256 AKM suite support
rtw88
* improve USB performance by aggregation
rtw89
* Wi-Fi 6 chip RTL8852BE-VT support
* WoWLAN net-detect support
* hardware encryption in unicast management frames support
* hardware rfkill support
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
iwlwifi
* channel puncturing for US/CAN from UEFI
* bump FW API to 93 for BZ/SC devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmbYfCARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt+Qwf/X9oQ4sf8jV6eOV7EhoWhIHnQadvo5YBZ
ulBm8In0QGjEOVWkI7kXGabKP5jhne2lVIyP1eFfP2/td/A2yDWIuEeBfDQD6f4K
aiUGAa1gs4ZtGKJBniw/ukflSqJlR99N2qBO5T/smDm3Nw/aC522SO7BoLTpoJDQ
SuW4atFHMShXYf/vIrAA2yB9ok2yw/QM+27M9qjj6D7zzqsQxDl9wKGW+2v8KiSa
rXXbfnwfaQP21CYv5xYbEPACSRSV5Dr0TNopivWYxmm9svjLzwFN2JM2fHPxBEDh
wP6Ojp+Z32c1VbQtclLrwIQdlZ5yhU5MEDlVg5VLym9F83hv+oXTbA==
=lgVx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
pull-request: wireless-next-2024-09-04
here's a pull request to net-next tree, more info below. Please let me know if
there are any problems.
====================
Conflicts:
drivers/net/wireless/ath/ath12k/hw.c
38055789d1 ("wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850")
8be12629b4 ("wifi: ath12k: restore ASPM for supported hardwares only")
https://lore.kernel.org/87msldyj97.fsf@kernel.org
Link: https://patch.msgid.link/20240904153205.64C11C4CEC2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hopefully final fixes for v6.11 and this time only fixes to ath11k
driver. We need to revert hibernation support due to reported
regressions and we have a fix for kernel crash introduced in
v6.11-rc1.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmbYZsIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvwbAf/XhgO7uKuZnGfq6NBfyLIaXQjHRe6OSc0
/EJ+c9J3DK5vQUHcw2ALrBYtKPJIrgLIzMG+u4N/4klxLwWCzZpsMLTqNvUV4VRe
eKdD9v/0dZnrKrpmQxgtEoImc028gC5c2K9jDK4e9MU/kBMln9PpH3xyasnV9aLj
2ajkO7xdLooTJ4cdZtdDL9fd5px7IdghNgHiY+24lfuPY2AZV5AUK/AUHZw3CG6K
nXk6+PEO1Xr2P3SAc5yRYg4vXJIy7g8ELAGUj8f3XznvYKpcO+afce8By+H6GecQ
ofsWSLO86ajgu3wMMxyWhXFs8TAsyeE8fLJgNBqIfC05i1IkGfYwBg==
=C23H
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.11
Hopefully final fixes for v6.11 and this time only fixes to ath11k
driver. We need to revert hibernation support due to reported
regressions and we have a fix for kernel crash introduced in
v6.11-rc1.
* tag 'wireless-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
MAINTAINERS: wifi: cw1200: add net-cw1200.h
Revert "wifi: ath11k: support hibernation"
Revert "wifi: ath11k: restore country code during resume"
wifi: ath11k: fix NULL pointer dereference in ath11k_mac_get_eirp_power()
====================
Link: https://patch.msgid.link/20240904135906.5986EC4CECA@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This NIC doesn't have hardware IRQ coalescing. Under high load,
interrupts can adversely affect performance. To mitigate this, enable
software IRQ coalescing by default. On my system this increases receive
throughput with iperf3 from 853 MBit/sec to 934 MBit/s, decreases
interrupts from 69489/sec to 2016/sec, and decreases CPU utilization
from 27% (4x Cortex-A53) to 14%. Latency is not affected (as far as I
can tell).
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240903184912.4151926-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
axienet_dma_err_handler can race with axienet_stop in the following
manner:
CPU 1 CPU 2
====================== ==================
axienet_stop()
napi_disable()
axienet_dma_stop()
axienet_dma_err_handler()
napi_disable()
axienet_dma_stop()
axienet_dma_start()
napi_enable()
cancel_work_sync()
free_irq()
Fix this by setting a flag in axienet_stop telling
axienet_dma_err_handler not to bother doing anything. I chose not to use
disable_work_sync to allow for easier backporting.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Link: https://patch.msgid.link/20240903175141.4132898-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Considering that CO-RE direct read access to the first system call
argument is already available on s390 and arm64, let's enable
test_bpf_syscall_macro:syscall_arg1 on these architectures.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240831041934.1629216-4-pulehui@huaweicloud.com
Currently PT_REGS_PARM1 SYSCALL(x) is consistent with PT_REGS_PARM1_CORE
SYSCALL(x), which will introduce the overhead of BPF_CORE_READ(), taking
into account the read pt_regs comes directly from the context, let's use
CO-RE direct read to access the first system call argument.
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/bpf/20240831041934.1629216-3-pulehui@huaweicloud.com
Currently PT_REGS_PARM1 SYSCALL(x) is consistent with PT_REGS_PARM1_CORE
SYSCALL(x), which will introduce the overhead of BPF_CORE_READ(), taking
into account the read pt_regs comes directly from the context, let's use
CO-RE direct read to access the first system call argument.
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240831041934.1629216-2-pulehui@huaweicloud.com
When reading registers from the PHY using the SIOCGMIIREG IOCTL any
errors returned from either mdiobus_read() or mdiobus_c45_read() are
ignored, and parts of the returned error is passed as the register value
back to user-space.
For example, if mdiobus_c45_read() is used with a bus that do not
implement the read_c45() callback -EOPNOTSUPP is returned. This is
however directly stored in mii_data->val_out and returned as the
registers content. As val_out is a u16 the error code is truncated and
returned as a plausible register value.
Fix this by first checking the return value for errors before returning
it as the register content.
Before this patch,
# phytool read eth0/0:1/0
0xffa1
After this change,
$ phytool read eth0/0:1/0
error: phy_read (-95)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20240903171536.628930-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant, and using IS_ERR is
safe enough.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://patch.msgid.link/20240903143343.2004652-1-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant, and using IS_ERR is
safe enough.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://patch.msgid.link/20240903143149.2004530-1-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
Unmask upper DSCP bits - part 3
tl;dr - This patchset continues to unmask the upper DSCP bits in the
IPv4 flow key in preparation for allowing IPv4 FIB rules to match on
DSCP. No functional changes are expected.
The TOS field in the IPv4 flow key ('flowi4_tos') is used during FIB
lookup to match against the TOS selector in FIB rules and routes.
It is currently impossible for user space to configure FIB rules that
match on the DSCP value as the upper DSCP bits are either masked in the
various call sites that initialize the IPv4 flow key or along the path
to the FIB core.
In preparation for adding a DSCP selector to IPv4 and IPv6 FIB rules, we
need to make sure the entire DSCP value is present in the IPv4 flow key.
This patchset continues to unmask the upper DSCP bits, but this time in
the output route path, specifically in the callers of
ip_route_output_ports().
The next patchset (last) will handle the callers of
ip_route_output_key(). Split from this patchset to avoid going over the
15 patches limit.
No functional changes are expected as commit 1fa3314c14 ("ipv4:
Centralize TOS matching") moved the masking of the upper DSCP bits to
the core where 'flowi4_tos' is matched against the TOS selector.
====================
Link: https://patch.msgid.link/20240903135327.2810535-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240903135327.2810535-5-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240903135327.2810535-4-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240903135327.2810535-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function is passed the full DS field in its 'tos' argument by its
two callers. It then masks the upper DSCP bits using RT_TOS() when
passing it to ip_route_output_ports().
Unmask the upper DSCP bits when passing 'tos' to ip_route_output_ports()
so that in the future it could perform the FIB lookup according to the
full DSCP value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240903135327.2810535-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240904014441.1065753-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The core part of the selftest, i.e., the je <-> jmp cycle, mimics the
original sched-ext bpf program. The test will fail without the
previous patch.
I tried to create some cases for other potential cycles
(je <-> je, jmp <-> je and jmp <-> jmp) with similar pattern
to the test in this patch, but failed. So this patch
only contains one test for je <-> jmp cycle.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240904221256.37389-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Hodges reported a jit error when playing with a sched-ext program.
The error message is:
unexpected jmp_cond padding: -4 bytes
But further investigation shows the error is actual due to failed
convergence. The following are some analysis:
...
pass4, final_proglen=4391:
...
20e: 48 85 ff test rdi,rdi
211: 74 7d je 0x290
213: 48 8b 77 00 mov rsi,QWORD PTR [rdi+0x0]
...
289: 48 85 ff test rdi,rdi
28c: 74 17 je 0x2a5
28e: e9 7f ff ff ff jmp 0x212
293: bf 03 00 00 00 mov edi,0x3
Note that insn at 0x211 is 2-byte cond jump insn for offset 0x7d (-125)
and insn at 0x28e is 5-byte jmp insn with offset -129.
pass5, final_proglen=4392:
...
20e: 48 85 ff test rdi,rdi
211: 0f 84 80 00 00 00 je 0x297
217: 48 8b 77 00 mov rsi,QWORD PTR [rdi+0x0]
...
28d: 48 85 ff test rdi,rdi
290: 74 1a je 0x2ac
292: eb 84 jmp 0x218
294: bf 03 00 00 00 mov edi,0x3
Note that insn at 0x211 is 6-byte cond jump insn now since its offset
becomes 0x80 based on previous round (0x293 - 0x213 = 0x80). At the same
time, insn at 0x292 is a 2-byte insn since its offset is -124.
pass6 will repeat the same code as in pass4. pass7 will repeat the same
code as in pass5, and so on. This will prevent eventual convergence.
Passes 1-14 are with padding = 0. At pass15, padding is 1 and related
insn looks like:
211: 0f 84 80 00 00 00 je 0x297
217: 48 8b 77 00 mov rsi,QWORD PTR [rdi+0x0]
...
24d: 48 85 d2 test rdx,rdx
The similar code in pass14:
211: 74 7d je 0x290
213: 48 8b 77 00 mov rsi,QWORD PTR [rdi+0x0]
...
249: 48 85 d2 test rdx,rdx
24c: 74 21 je 0x26f
24e: 48 01 f7 add rdi,rsi
...
Before generating the following insn,
250: 74 21 je 0x273
"padding = 1" enables some checking to ensure nops is either 0 or 4
where
#define INSN_SZ_DIFF (((addrs[i] - addrs[i - 1]) - (prog - temp)))
nops = INSN_SZ_DIFF - 2
In this specific case,
addrs[i] = 0x24e // from pass14
addrs[i-1] = 0x24d // from pass15
prog - temp = 3 // from 'test rdx,rdx' in pass15
so
nops = -4
and this triggers the failure.
To fix the issue, we need to break cycles of je <-> jmp. For example,
in the above case, we have
211: 74 7d je 0x290
the offset is 0x7d. If 2-byte je insn is generated only if
the offset is less than 0x7d (<= 0x7c), the cycle can be
break and we can achieve the convergence.
I did some study on other cases like je <-> je, jmp <-> je and
jmp <-> jmp which may cause cycles. Those cases are not from actual
reproducible cases since it is pretty hard to construct a test case
for them. the results show that the offset <= 0x7b (0x7b = 123) should
be enough to cover all cases. This patch added a new helper to generate 8-bit
cond/uncond jmp insns only if the offset range is [-128, 123].
Reported-by: Daniel Hodges <hodgesd@meta.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240904221251.37109-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
RT_TOS() from include/uapi/linux/in_route.h is defined using
IPTOS_TOS_MASK from include/uapi/linux/ip.h. This is problematic for
files such as include/net/ip_fib.h that want to use RT_TOS() as without
including both header files kernel compilation fails:
In file included from ./include/net/ip_fib.h:25,
from ./include/net/route.h:27,
from ./include/net/lwtunnel.h:9,
from net/core/dst.c:24:
./include/net/ip_fib.h: In function ‘fib_dscp_masked_match’:
./include/uapi/linux/in_route.h:31:32: error: ‘IPTOS_TOS_MASK’ undeclared (first use in this function)
31 | #define RT_TOS(tos) ((tos)&IPTOS_TOS_MASK)
| ^~~~~~~~~~~~~~
./include/net/ip_fib.h:440:45: note: in expansion of macro ‘RT_TOS’
440 | return dscp == inet_dsfield_to_dscp(RT_TOS(fl4->flowi4_tos));
Therefore, cited commit changed linux/in_route.h to include linux/ip.h.
However, as reported by David, this breaks iproute2 compilation due
overlapping definitions between linux/ip.h and
/usr/include/netinet/ip.h:
In file included from ../include/uapi/linux/in_route.h:5,
from iproute.c:19:
../include/uapi/linux/ip.h:25:9: warning: "IPTOS_TOS" redefined
25 | #define IPTOS_TOS(tos) ((tos)&IPTOS_TOS_MASK)
| ^~~~~~~~~
In file included from iproute.c:17:
/usr/include/netinet/ip.h:222:9: note: this is the location of the previous definition
222 | #define IPTOS_TOS(tos) ((tos) & IPTOS_TOS_MASK)
Fix by changing include/net/ip_fib.h to include linux/ip.h. Note that
usage of RT_TOS() should not spread further in the kernel due to recent
work in this area.
Fixes: 1fa3314c14 ("ipv4: Centralize TOS matching")
Reported-by: David Ahern <dsahern@kernel.org>
Closes: https://lore.kernel.org/netdev/2f5146ff-507d-4cab-a195-b28c0c9e654e@kernel.org/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/20240903133554.2807343-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit aa92c1cec9 ("l2tp: add tunnel/session get_next helpers") uses
idr_get_next APIs to iterate over l2tp session IDR lists. Sessions in
l2tp_v2_session_idr always have a non-null session->tunnel pointer
since l2tp_session_register sets it before inserting the session into
the IDR. Therefore the null check on session->tunnel in
l2tp_v2_session_get_next is redundant and can be removed. Removing the
check avoids a warning from lkp.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202408111407.HtON8jqa-lkp@intel.com/
CC: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Acked-by: Tom Parkin <tparkin@katalix.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240903113547.1261048-1-jchapman@katalix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When userspace wants to take over a fdb entry by setting it as
EXTERN_LEARNED, we set both flags BR_FDB_ADDED_BY_EXT_LEARN and
BR_FDB_ADDED_BY_USER in br_fdb_external_learn_add().
If the bridge updates the entry later because its port changed, we clear
the BR_FDB_ADDED_BY_EXT_LEARN flag, but leave the BR_FDB_ADDED_BY_USER
flag set.
If userspace then wants to take over the entry again,
br_fdb_external_learn_add() sees that BR_FDB_ADDED_BY_USER and skips
setting the BR_FDB_ADDED_BY_EXT_LEARN flags, thus silently ignores the
update.
Fix this by always allowing to set BR_FDB_ADDED_BY_EXT_LEARN regardless
if this was a user fdb entry or not.
Fixes: 710ae72877 ("net: bridge: Mark FDB entries that were added by user as such")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20240903081958.29951-1-jonas.gorski@bisdn.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a611 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mana_set_channels() function requires detaching the mana
driver and reattaching it with changed channel values.
During this operation if the system is low on memory, the reattach
might fail, causing the network device being down.
To avoid this we pre-allocate buffers at the beginning of set operation,
to prevent complete network loss
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/1725248734-21760-1-git-send-email-shradhagupta@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Native PCIe Enclosure Management (NPEM, PCIe r6.1 sec 6.28) allows managing
LEDs in storage enclosures. NPEM is indication oriented and it does not
give direct access to LEDs. Although each indication *could* represent an
individual LED, multiple indications could also be represented as a single,
multi-color LED or a single LED blinking in a specific interval. The
specification leaves that open.
Each enabled indication (capability register bit on) is represented as a
ledclass_dev which can be controlled through sysfs. For every ledclass
device only 2 brightness states are allowed: LED_ON (1) or LED_OFF (0).
This corresponds to the NPEM control register (Indication bit on/off).
Ledclass devices appear in sysfs as child devices (subdirectory) of PCI
device which has an NPEM Extended Capability and indication is enabled in
NPEM capability register. For example, these are LEDs created for pcieport
"10000:02:05.0" on my setup:
leds/
├── 10000:02:05.0:enclosure:fail
├── 10000:02:05.0:enclosure:locate
├── 10000:02:05.0:enclosure:ok
└── 10000:02:05.0:enclosure:rebuild
They can be also found in "/sys/class/leds" directory. The parent PCIe
device domain/bus/device/function address is used to guarantee uniqueness
across leds subsystem.
To enable/disable a "fail" indication, the "brightness" file can be edited:
echo 1 > ./leds/10000:02:05.0:enclosure:fail/brightness
echo 0 > ./leds/10000:02:05.0:enclosure:fail/brightness
PCIe r6.1, sec 7.9.19.2 defines the possible indications.
Multiple indications for same parent PCIe device can conflict and hardware
may update them when processing new request. To avoid issues, driver
refresh all indications by reading back control register.
This driver expects to be the exclusive NPEM extended capability manager.
It waits up to 1 second after imposing new request, it doesn't verify if
controller is busy before write, and it assumes the mutex lock gives
protection from concurrent updates.
If _DSM LED management is available, we assume the platform may be using
NPEM for its own purposes (see PCI Firmware Spec r3.3 sec 4.7), so the
driver does not use NPEM. A future patch will add _DSM support; an info
message notes whether NPEM or _DSM is being used.
NPEM is a PCIe extended capability so it should be registered in
pcie_init_capabilities() but it is not possible due to LED dependency. The
parent pci_device must be added earlier for led_classdev_register() to be
successful. NPEM does not require configuration on kernel side, so it is
safe to register LED devices later.
Link: https://lore.kernel.org/r/20240904104848.23480-3-mariusz.tkaczyk@linux.intel.com
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
NPEM driver will require leds class, there is an init-order conflict.
Make sure that LEDs initialization happens first and add comment.
Link: https://lore.kernel.org/r/20240904104848.23480-2-mariusz.tkaczyk@linux.intel.com
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Depending on if array has personality, it is either reported as active or
inactive. This patch adds third status "broken" for arrays with
personality that became inoperative. The reason is end users tend to
assume that "active" indicates array is operational.
Add "broken" state for inoperative arrays with personality and refactor
the code.
Signed-off-by: Mateusz Kusiak <mateusz.kusiak@intel.com>
Link: https://lore.kernel.org/r/20240903142949.53628-1-mateusz.kusiak@intel.com
Signed-off-by: Song Liu <song@kernel.org>
Bareudp devices update their stats concurrently.
Therefore they need proper atomic increments.
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/04b7b9d0b480158eb3ab4366ec80aa2ab7e41fcb.1725031794.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull bpf/master to receive baebe9aaba ("bpf: allow passing struct
bpf_iter_<type> as kfunc arguments") and related changes in preparation for
the DSQ iterator patchset.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix eventfs ownership testcase to find mount point if stat -c "%m" failed.
This can happen on the system based on busybox. In this case, this will
try to use the current working directory, which should be a tracefs top
directory (and eventfs is mounted as a part of tracefs.)
If it does not work, the test is skipped as UNRESOLVED because of
the environmental problem.
Fixes: ee9793be08 ("tracing/selftests: Add ownership modification tests for eventfs")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
- Fix a typo in the rebalance accounting changes
- BCH_SB_MEMBER_INVALID: small on disk format feature which will be
needed for full erasure coding support; this is only the minimum so
that 6.11 can handle future versions without barfing.
-----BEGIN PGP SIGNATURE-----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=ABhR
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-09-04' of git://evilpiepirate.org/bcachefs
Pull bcachefs fixes from Kent Overstreet:
- Fix a typo in the rebalance accounting changes
- BCH_SB_MEMBER_INVALID: small on disk format feature which will be
needed for full erasure coding support; this is only the minimum so
that 6.11 can handle future versions without barfing.
* tag 'bcachefs-2024-09-04' of git://evilpiepirate.org/bcachefs:
bcachefs: BCH_SB_MEMBER_INVALID
bcachefs: fix rebalance accounting
The newly created cpuset-v1.c file uses cpus_read_lock/unlock() functions
which are defined in cpu.h but not included in cpuset-internal.h yet
leading to compilation error under certain kernel configurations. Fix it
by moving the cpu.h include from cpuset.c to cpuset-internal.h. While
at it, sort the include files in alphabetic order.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408311612.mQTuO946-lkp@intel.com/
Fixes: 047b830974 ("cgroup/cpuset: move relax_domain_level to cpuset-v1.c")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds scx_flatcg example scheduler which implements hierarchical
weight-based cgroup CPU control by flattening the cgroup hierarchy into a
single layer by compounding the active weight share at each level.
This flattening of hierarchy can bring a substantial performance gain when
the cgroup hierarchy is nested multiple levels. in a simple benchmark using
wrk[8] on apache serving a CGI script calculating sha1sum of a small file,
it outperforms CFS by ~3% with CPU controller disabled and by ~10% with two
apache instances competing with 2:1 weight ratio nested four level deep.
However, the gain comes at the cost of not being able to properly handle
thundering herd of cgroups. For example, if many cgroups which are nested
behind a low priority parent cgroup wake up around the same time, they may
be able to consume more CPU cycles than they are entitled to. In many use
cases, this isn't a real concern especially given the performance gain.
Also, there are ways to mitigate the problem further by e.g. introducing an
extra scheduling layer on cgroup delegation boundaries.
v5: - Updated to specify SCX_OPS_HAS_CGROUP_WEIGHT instead of
SCX_OPS_KNOB_CGROUP_WEIGHT.
v4: - Revert reference counted kptr for cgv_node as the change caused easily
reproducible stalls.
v3: - Updated to reflect the core API changes including ops.init/exit_task()
and direct dispatch from ops.select_cpu(). Fixes and improvements
including additional statistics.
- Use reference counted kptr for cgv_node instead of xchg'ing against
stash location.
- Dropped '-p' option.
v2: - Use SCX_BUG[_ON]() to simplify error handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
Add sched_ext_ops operations to init/exit cgroups, and track task migrations
and config changes. A BPF scheduler may not implement or implement only
subset of cgroup features. The implemented features can be indicated using
%SCX_OPS_HAS_CGOUP_* flags. If cgroup configuration makes use of features
that are not implemented, a warning is triggered.
While a BPF scheduler is being enabled and disabled, relevant cgroup
operations are locked out using scx_cgroup_rwsem. This avoids situations
like task prep taking place while the task is being moved across cgroups,
making things easier for BPF schedulers.
v7: - cgroup interface file visibility toggling is dropped in favor just
warning messages. Dynamically changing interface visiblity caused more
confusion than helping.
v6: - Updated to reflect the removal of SCX_KF_SLEEPABLE.
- Updated to use CONFIG_GROUP_SCHED_WEIGHT and fixes for
!CONFIG_FAIR_GROUP_SCHED && CONFIG_EXT_GROUP_SCHED.
v5: - Flipped the locking order between scx_cgroup_rwsem and
cpus_read_lock() to avoid locking order conflict w/ cpuset. Better
documentation around locking.
- sched_move_task() takes an early exit if the source and destination
are identical. This triggered the warning in scx_cgroup_can_attach()
as it left p->scx.cgrp_moving_from uncleared. Updated the cgroup
migration path so that ops.cgroup_prep_move() is skipped for identity
migrations so that its invocations always match ops.cgroup_move()
one-to-one.
v4: - Example schedulers moved into their own patches.
- Fix build failure when !CONFIG_CGROUP_SCHED, reported by Andrea Righi.
v3: - Make scx_example_pair switch all tasks by default.
- Convert to BPF inline iterators.
- scx_bpf_task_cgroup() is added to determine the current cgroup from
CPU controller's POV. This allows BPF schedulers to accurately track
CPU cgroup membership.
- scx_example_flatcg added. This demonstrates flattened hierarchy
implementation of CPU cgroup control and shows significant performance
improvement when cgroups which are nested multiple levels are under
competition.
v2: - Build fixes for different CONFIG combinations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andrea Righi <andrea.righi@canonical.com>
sched_ext will soon add cgroup cpu.weigh support. The cgroup interface code
is currently gated behind CONFIG_FAIR_GROUP_SCHED. As the fair class and/or
SCX may implement the feature, put the interface code behind the new
CONFIG_CGROUP_SCHED_WEIGHT which is selected by CONFIG_FAIR_GROUP_SCHED.
This allows either sched class to enable the itnerface code without ading
more complex CONFIG tests.
When !CONFIG_FAIR_GROUP_SCHED, a dummy version of sched_group_set_shares()
is added to support later CONFIG_CGROUP_SCHED_WEIGHT &&
!CONFIG_FAIR_GROUP_SCHED builds.
No functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Move tg_weight() upward and make cpu_shares_read_u64() use it too. This
makes the weight retrieval shared between cgroup v1 and v2 paths and will be
used to implement cgroup support for sched_ext.
No functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
A new BPF extensible sched_class will use css_tg() in the init and exit
paths to visit all task_groups by walking cgroups.
v4: __setscheduler_prio() is already exposed. Dropped from this patch.
v3: Dropped SCHED_CHANGE_BLOCK() as upstream is adding more generic cleanup
mechanism.
v2: Expose SCHED_CHANGE_BLOCK() too and update the description.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
