Add a check for errors in the start_io function that signal a not
working device. Trigger an autoquiesce event in that case.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-7-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a sysfs attribute aq_timeouts that controls after how many
timeouts a autoquiesce event might be triggered.
The default value is 32768 which is the maximum number of retries
for the DASD device driver DASD_RETRIES_MAX. This means that the
timeout trigger will never happen.
The default value for DASD retries is 255.
Setting the value to below 255 will trigger the timeout autoquiesce
event before an IO error is generated.
Also add the check for the configured amount of timeouts and trigger
an autoquiesce event if exceeded.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-6-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a sysfs attribute to control if all IO requests will be requeued to
the blocklayer in case of an autoquiesce event or not.
A value of 1 means that in case of an autoquiesce event all IO requests
will be requeued to the blocklayer.
A value of 0 means that the device will only be stopped.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-5-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add sysfs attribute that controls the DASD autoquiesce feature.
The autoquiesce is disabled when 0 is echoed to the attribute.
A value greater than 0 will enable the feature.
The aq_mask attribute will accept an unsigned integer and the value
will be interpreted as bitmask defining the trigger events that will
lead to an automatic quiesce.
The following autoquiesce triggers will currently be available:
DASD_EER_FATALERROR 1 - any final I/O error
DASD_EER_NOPATH 2 - no remaining paths for the device
DASD_EER_STATECHANGE 3 - a state change interrupt occurred
DASD_EER_PPRCSUSPEND 4 - the device is PPRC suspended
DASD_EER_NOSPC 5 - there is no space remaining on an ESE device
DASD_EER_TIMEOUT 6 - a certain amount of timeouts occurred
DASD_EER_STARTIO 7 - the IO start function encountered an error
The currently supported maximum value is 255.
Bit 31 is reserved for internal usage.
Bit 0 is not used.
Example:
- deactivate autoquiesce
$ echo 0 > /sys/bus/ccw/0.0.1234/aq_mask
- enable autoquiesce for FATALERROR, NOPATH and TIMEOUT
(0000 0000 0000 0000 0000 0000 0100 0110 => 70)
$ echo 70 > /sys/bus/ccw/0.0.1234/aq_mask
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the internal logic to check for autoquiesce triggers and handle
them.
Quiesce and resume are functions that tell Linux to stop/resume
issuing I/Os to a specific DASD.
The DASD driver allows a manual quiesce/resume via ioctl.
Autoquiesce will define an amount of triggers that will lead to
an automatic quiesce if a certain event occurs.
There is no automatic resume.
All events will be reported via DASD Extended Error Reporting (EER)
if configured.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove definitions that have never been used.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20230405142017.2446986-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add DT compatible for Data Modul i.MX8M Plus eDM SBC board.
This is an evaluation board for various custom display units.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the compatibles for the chargebyte Tarragon boards.
Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
chargebyte supplies hardware and software products for all
aspects of charging communication.
https://chargebyte.com/
Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In lpfc_sli4_pci_mem_unset(), case LPFC_SLI_INTF_IF_TYPE_1 does not have a
break statement, resulting in an incorrect device output.
Fix this by adding a break statement before the default option.
Signed-off-by: Jun Chen <jun_c@hust.edu.cn>
Link: https://lore.kernel.org/r/20230410023724.3209455-1-jun_c@hust.edu.cn
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses spin lock without irqsave when it needs to acquire a chain
frame. This is done to protect chain frame allocation from multiple
submission threads. If there is any I/O queued from an interrupt context,
and if that requires a chain frame, and if the chain lock is held by the CPU
which got interrupted, then there will be a possible deadlock.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230406101819.10109-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch reports: drivers/scsi/scsi_debug.c:6996
scsi_debug_init() warn: missing error code 'ret'
Although it is unlikely that KMEM_CACHE might fail, but if it does then ret
might be zero. So to fix this explicitly mark ret as "-ENOMEM" and then
goto driver_unreg.
Fixes: 1107c7b24e ("scsi: scsi_debug: Dynamically allocate sdebug_queued_cmd")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230406074607.3637097-1-harshit.m.mogalapalli@oracle.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The suspend/resume functions in this driver seem to have multiple problems,
the latest one just got introduced by a bugfix:
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function '_suspend_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:5142:39: error: 'struct dev_pm_info' has no member named 'usage_count'
5142 | if (atomic_read(&device->power.usage_count)) {
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function '_suspend_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:5142:39: error: 'struct dev_pm_info' has no member named 'usage_count'
5142 | if (atomic_read(&device->power.usage_count)) {
As far as I can tell, the 'usage_count' is not meant to be accessed by
device drivers at all, though I don't know what the driver is supposed to
do instead.
Another problem is the use of the deprecated UNIVERSAL_DEV_PM_OPS(), and
marking functions as __maybe_unused to avoid warnings about unused
functions. This should probably be changed to using
DEFINE_RUNTIME_DEV_PM_OPS().
Both changes require actually understanding what the driver needs to do,
and being able to test this, so instead here is the simplest patch to make
it pass the randconfig builds instead.
Fixes: e368d38cb9 ("scsi: hisi_sas: Exit suspend state when usage count is greater than 0")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230405083611.3376739-1-arnd@kernel.org
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.
Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely
scsi 2:0:0:254: enclosure has no enumerated components
scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such
even on valid configurations with 1 primary and 0 secondary enclosures as
below:
# sg_ses /dev/sg0
3PARdata SES 3321
Supported diagnostic pages:
Supported Diagnostic Pages [sdp] [0x0]
Configuration (SES) [cf] [0x1]
Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
3PARdata SES 3321
Configuration diagnostic page:
number of secondary subenclosures: 0
generation code: 0x0
enclosure descriptor list
Subenclosure identifier: 0 [primary]
relative ES process id: 0, number of ES processes: 1
number of type descriptor headers: 1
enclosure logical identifier (hex): 20000002ac02068d
enclosure vendor: 3PARdata product: VV rev: 3321
type descriptor header and text list
Element type: Unspecified, subenclosure id: 0
number of possible elements: 1
The changelog for the original fix follows
=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:
[ffff00002a00fb70] kfree at ffff00000830e224
[ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
[ffff00002a00fbd0] device_del at ffff0000086b6a98
[ffff00002a00fc50] device_unregister at ffff0000086b6d58
[ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
[ffff00002a00fca0] scsi_remove_device at ffff000008706134
[ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
[ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
[ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
[ffff00002a00fdb0] process_one_work at ffff00000810f35c
[ffff00002a00fe00] worker_thread at ffff00000810f648
[ffff00002a00fe70] kthread at ffff000008116e98
In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch
In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer
We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
=====
Reported-by: Michal Kolar <mich.k@seznam.cz>
Originally-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: stable@vger.kernel.org
Fixes: 3fe97ff3d9 ("scsi: ses: Don't attach if enclosure has no components")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm
Tested-by: Michal Kolar <mich.k@seznam.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels.
Fixes: 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Shuchang Li <lishuchang@hust.edu.cn>
Link: https://lore.kernel.org/r/20230404072133.1022-1-lishuchang@hust.edu.cn
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Warnings may be logged during driver removal:
mpt3sas 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT ..,
Fix this by deallocating DMA memory later.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230403184736.6399-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is done to avoid ambiguity between BIOS and UEFI versions. Management
tools can be used for getting accurate firmware version information.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230322092713.6961-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the preferred form of branch-and-link for finding the current
address so objtool doesn't think it is an unannotated intra-function
call.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230407040924.231023-1-npiggin@gmail.com
This reverts commit baf7cbd94b.
There are some duplicate cache attributes populations executed
in both ci_leaf_init() and later cache_setup_properties().
Revert the commit baf7cbd94b ("riscv: Set more data to cacheinfo")
to setup only the level and type attributes at this early place.
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230308064734.512457-1-suagrfillet@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
All callers of pci_bridge_wait_for_secondary_bus() supply a timeout of
PCIE_RESET_READY_POLL_MS, so drop the parameter. Move the definition of
PCIE_RESET_READY_POLL_MS into pci.c, the only user.
[bhelgaas: extracted from
https://lore.kernel.org/r/20230404052714.51315-3-mika.westerberg@linux.intel.com]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.0 sec 6.6.1 prescribes that a device must be able to respond to
config requests within 1.0 s (PCI_RESET_WAIT) after exiting conventional
reset and this same delay is prescribed when coming out of D3cold (as that
involves reset too).
A device that requires more than 1 second to initialize after reset may
respond to config requests with Request Retry Status completions (sec
2.3.1), and we accommodate that in Linux with a 60 second cap
(PCIE_RESET_READY_POLL_MS).
Previously we waited up to PCIE_RESET_READY_POLL_MS only in the reset code
path, not in the resume path. However, a device has surfaced, namely Intel
Titan Ridge xHCI, which requires a longer delay also in the resume code
path.
Make the resume code path to use this same extended delay as the reset
path.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216728
Link: https://lore.kernel.org/r/20230404052714.51315-2-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Newline characters will be taken into account for the firmware search
path parameter, warn users about that and provide an example using 'echo
-n' such that it clarifies the typical use of that parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230402135423.3235-1-f.fainelli@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Enable SDMA queue empty context switching. SDMA context switch due to
quantum programming no longer done here (as of sdma v6), so re-name
sdma_v6_0_ctx_switch_enable to sdma_v6_0_ctxempty_int_enable to reflect
this.
Also program SDMAx_QUEUEx_SCHEDULE_CNTL for context switch due to
quantum in KFD. Set to amdgpu_sdma_phase_quantum (defaults to 32 i.e.
3200us).
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CP_HQD_HQ_STATUS0[29] bit will be used by CPFW to acknowledge whether
PCIe atomics are supported. The default value of this bit is set
to 0. Driver will check whether PCIe atomics are supported and set the
bit to 1 if supported. This will force CPFW to use real atomic ops.
If the bit is not set, CPFW will default to read/modify/write using the
firmware itself.
This is applicable only to GFX11 RS64 CP with MEC FW >= 509. If MEC
FW < 509 and for all GFX11 F32 CP, PCIe atomics needs to be supported
else it will skip the device.
This commit also involves moving amdgpu_amdkfd_device_probe() function
call after per-IP early_init loop in amdgpu_device_ip_early_init()
function so as to check for RS64 enabled device.
Signed-off-by: Sreekant Somasekharan <sreekant.somasekharan@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some more logging for DP link traning test pattern seqeunces
for better debugging.
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XGMI RAS should be according to the gmc xgmi physical nodes number,
XGMI RAS should not be enabled if xgmi num_physical_nodes is zero.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran supports VCN and JPEG RAS, it reports unexpected
block id message during VCN and JPEG RAS initialization if VCN
and JPEG block id not defined.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This achieves the same result as the sequence used in emit_flush_gpu_tlb
but the invalidation is now a single packet instead of the 3 packets
required to implement reg_write_reg_wait.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the existing log with DP LT downspread info:
[Downstream devices shall support down spreading of the link clock.
The down-spread amplitude shall either be disabled (0.0%) or up to 0.5%,
as written by the upstream device to the DOWNSPREAD_CTRL register
(DPCD 00107h). The modulation frequency range shall be 30 to 33 kHz]
Besides, fix checkpatch warning:
CHECK: Alignment should match open parenthesis
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang with W=1 reports
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_enc_cfg.c:625:6: error:
variable 'matching_stream_ptrs' set but not used [-Werror,-Wunused-but-set-variable]
int matching_stream_ptrs = 0;
^
This variable is not used so remove it.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:44:24: warning: symbol
'dml20_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:51:24: warning: symbol
'dml20v2_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:58:24: warning: symbol
'dml21_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:65:24: warning: symbol
'dml30_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:72:24: warning: symbol
'dml31_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:79:24: warning: symbol
'dml314_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:86:24: warning: symbol
'dml32_funcs' was not declared. Should it be static?
These variables are only used in one file so should be static.
Cleanup whitespace, use tabs consistently for indents.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubp.c:758:10: warning: symbol
'aperture_default_system' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubp.c:759:10: warning: symbol
'context0_default_system' was not declared. Should it be static?
These variables are only used in one file so should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/dcn314_fpu.c💯37: warning: symbol
'dcn3_14_soc' was not declared. Should it be static?
This variable is only used in one file so should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER are protected and
unaccessible under sriov.
The clock counter high bit may update during reading process.
[How]
Replace regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER with
regCP_MES_MTIME_LO/regCP_MES_MTIME_HI to get gpu clock under sriov.
Refine get gpu clock counter method to make the result more precise.
Signed-off-by: Tong Liu01 <Tong.Liu01@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DMA-MAP userptr on other GPUs, the dma address array
will be populated in amdgpu_ttm_backend_bind.
Remove the redundant call from the driver.
v2:
update the comment
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SG BO to DMA-map userptrs on other GPUs, the SG BO
need inherit MTYPEs in PTEs from original BO.
If we set the flags, the device can be coherent with
the CPUs and other GPUs.
v2:
1. Drop unnecessary flags check
2. Remove local variable align
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The comment mentions that power1 cap attributes are not supported on
Vangogh, but the opposite is indeed valid: for APUs, only Vangogh is
supported. While at it, also fixed the Renoir comment below (thanks
Melissa for noticing that!).
Cc: Lijo Lazar <lijo.lazar@amd.com>
Cc: Melissa Wen <mwen@igalia.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For userptr bo with iommu on, multiple GPUs use same system
memory dma mapping address when both adev and bo_adev are in
identity mode or in the same iommu group.
If RAM direct map to one GPU, other GPUs can share the original
BO in order to reduce dma address array usage when RAM can
direct map to these GPUs. However, we should explicit check
whether RAM can direct map to all these GPUs.
This patch fixes a potential issue that where RAM is
direct mapped on some but not all GPUs.
v2:
1. Update comment
2. Add helper function reuse_dmamap
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver doesn't resubmit jobs on hangs any more, hence drop
the hang limit parameter - amdgpu_job_hang_limit, wherever it is used.
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Kent Russell <kent.russell@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
