After commit d6e6286a12 ("libbpf: disassociate section handler on explicit
bpf_program__set_type() call"), bpf_program__set_type() will force cleanup
the program's SEC() definition, this commit fixed the test helper but missed
the bpftool, which leads to bpftool prog autoattach broken as follows:
$ bpftool prog load spi-xfer-r1v1.o /sys/fs/bpf/test autoattach
Program spi_xfer_r1v1 does not support autoattach, falling back to pinning
This patch fix bpftool to set program type only if it differs.
Fixes: d6e6286a12 ("libbpf: disassociate section handler on explicit bpf_program__set_type() call")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230407081427.2621590-1-weiyongjun@huaweicloud.com
perf_event with type=PERF_TYPE_RAW and config=0x1b00 turned out to be not
reliable in ensuring LBR is active. Thus, test_progs:get_branch_snapshot is
not reliable in some systems. Replace it with PERF_COUNT_HW_CPU_CYCLES
event, which gives more consistent results.
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20230407190130.2093736-1-song@kernel.org
Some code was left over from debugging the driver while it was in
development. Remove this code as it's not needed.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
edr_handle_event
dpc_process_error(dev) # "dev" triggered DPC
pcie_do_recovery(dev, dpc_reset_link)
dpc_reset_link # exit DPC
pcie_clear_device_status(dev) # clear Device Status
After 068c29a248, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log]
Fixes: 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER")
Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Tsaur Erwin <erwin.tsaur@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- fix irq handling in gpio-davinci
- fix Kconfig dependencies for gpio-regmap
-----BEGIN PGP SIGNATURE-----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=ZM6C
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix irq handling in gpio-davinci
- fix Kconfig dependencies for gpio-regmap
* tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: davinci: Add irq chip flag to skip set wake
gpio: davinci: Do not clear the bank intr enable bit in save_context
gpio: GPIO_REGMAP: select REGMAP instead of depending on it
Fix the ACPI backlight override mechanism for the cases when
acpi_backlight=video is set through the kernel command line or a DMI
quirk and add backlight quirks for Apple iMac14,1 and iMac14,2 and
Lenovo ThinkPad W530 (Hans de Goede).
-----BEGIN PGP SIGNATURE-----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=NpWd
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix the ACPI backlight override mechanism for the cases when
acpi_backlight=video is set through the kernel command line or a DMI
quirk and add backlight quirks for Apple iMac14,1 and iMac14,2 and
Lenovo ThinkPad W530 (Hans de Goede)"
* tag 'acpi-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: video: Add acpi_backlight=video quirk for Lenovo ThinkPad W530
ACPI: video: Add acpi_backlight=video quirk for Apple iMac14,1 and iMac14,2
ACPI: video: Make acpi_backlight=video work independent from GPU driver
ACPI: video: Add auto_detect arg to __acpi_video_get_backlight_type()
-----BEGIN PGP SIGNATURE-----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=xypJ
-----END PGP SIGNATURE-----
Merge tag '6.3-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull ksmbd server fixes from Steve French:
"Four fixes, three for stable:
- slab out of bounds fix
- lock cancellation fix
- minor cleanup to address clang warning
- fix for xfstest 551 (wrong parms passed to kvmalloc)"
* tag '6.3-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
ksmbd: delete asynchronous work from list
ksmbd: remove unused is_char_allowed function
ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
Bindings require pin configuration nodes to have the function, even if
it is GPIO:
msm8916-thwc-ufi001c.dtb: pinctrl@1000000: sim-ctrl-default-state: 'oneOf' conditional failed, one must be fixed:
'esim-sel-pins', 'sim-en-pins', 'sim-sel-pins' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-1-krzysztof.kozlowski@linaro.org
Add schema file for new Qualcomm Inline Crypto Engine driver.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407105029.2274111-2-abel.vesa@linaro.org
-----BEGIN PGP SIGNATURE-----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=jQJ7
-----END PGP SIGNATURE-----
Merge tag '20230407105029.2274111-4-abel.vesa@linaro.org' into drivers-for-6.4
The dedicated ICE driver was merged through a immutable tag, to make it
available to other maintainers.
This takes the already existing duplicated support in both ufs-qcom
and sdhci-msm drivers and makes it a dedicated driver that can be used
by both mentioned drivers.
The reason for this is because, staring with SM8550, the ICE IP block
is shared between UFS and SDCC, which means we need to probe a dedicated
device and share it between those two consumers.
So let's add the ICE dedicated driver as a soc driver.
Platforms that already have ICE supported, will use it as a library
as the of_qcom_ice_get will return an ICE instance created for the
consumer device. This allows the backwards compatibility with old-style
devicetree approach.
Also, add support to HW version 4.x since it works out-of-the-box with
the current driver. The 4.x HW version is found on SM8550 platform.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407105029.2274111-4-abel.vesa@linaro.org
Add nodes for remoteproc, smp2p and smsm in preparation
for audio support on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-4-a39.skl@gmail.com
Add nodes for remoteproc, smp2p and smsm to make it possible to use
modem functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-3-a39.skl@gmail.com
Add nodes for remoteproc, smp2p and smsm to make it possible to use
wifi/bt functionality on this platform.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407165345.42800-2-a39.skl@gmail.com
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-9-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-8-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-5-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-4-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-3-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-1-krzysztof.kozlowski@linaro.org
Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
summary on what's defined.
- dmesg output to bootloader preconfigured display
- USB
- UFS
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
- Thermistors
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-7-they@mint.lgbt
Document the Xiaomi Mi A3 (xiaomi-laurel-sprout) smartphone which is
based on the Snapdragon 665 SoC.
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-6-they@mint.lgbt
Add support for the Xiaomi Mi Pad 5 Pro CSOT variant. The CSOT variant
uses China Star Optoelectronics Technology (CSOT) panel based on NT36523
display controller.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-3-lujianhua000@gmail.com
Add nodes for BOE NT36523 panel found in xiaomi-elish. This panel
is a dual dsi mode panel and the dsi phy type is cphy.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-2-lujianhua000@gmail.com
There are two panel variants of xiaomi-elish, BOE and CSOT panels.
In order to support both panels, so split elish dts into common dtsi
and elish-boe dts.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-1-lujianhua000@gmail.com
Add an initial device tree for the QTI RB1 development board, based on
the QRB2210 (QCM2290 derivative) SoC. This device tree targets the SoM
revision 4, a.k.a. the Mass Production SKU.
To get a successful boot, run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/qrb2210-rb1.dtb >\
.Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd \
--output rb1-boot.img \
--pagesize 4096 \
--base 0x8000 \
--cmdline 'some cmdline'
fastboot boot rb1-boot.img
There's no dtbo or other craziness to worry about.
For the best dev experience, you can erase boot and use fastboot boot
everytime, so that the bootloader doesn't mess with you.
If you have a SoM revision 3 or older (there should be a sticker on it
with text like -r00, where r is the revision), you will need to apply
this additional diff:
aliases {
- serial0 = &uart0;
+ serial0 = &uart4;
/* UART connected to the Micro-USB port via a FTDI chip */
- &uart0 {
+ &uart4 {
That should however only concern preproduction boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-5-dae06f8830dc@linaro.org