This makes it harder for accidental or malicious changes to
cifs_xattr_handlers at runtime.
Cc: Steve French <sfrench@samba.org>
Cc: Paulo Alcantara <pc@manguebit.com>
Cc: Ronnie Sahlberg <lsahlber@redhat.com>
Cc: Shyam Prasad N <sprasad@microsoft.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Wedson Almeida Filho <walmeida@microsoft.com>
Link: https://lore.kernel.org/r/20230930050033.41174-24-wedsonaf@gmail.com
Reviewed-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
During board verification, there is a need to test the various supported
eMMC/SD speed modes. However, since the framework chooses the best mode
supported by the card and the host controller's caps, this currently
necessitates changing the devicetree for every iteration.
Allow the various speed mode host capabilities to be modified via
debugfs in order to allow easier hardware verification. The values to
be written are the raw MMC_CAP* values from include/linux/mmc/host.h.
This is rather low-level, and these defines are not guaranteed to be
stable, but it is perhaps good enough for the intended use case.
MMC_CAP_AGGRESSIVE_PM can also be set, in order to be able to
re-initialize the card without having to physically remove and re-insert
it.
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 9 (mmc HS200)
// Turn on MMC_CAP_AGGRESSIVE_PM and re-trigger runtime suspend
/sys/kernel/debug/mmc0# echo $(($(cat caps) | (1 << 7))) > caps
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# echo auto > /sys/bus/mmc/devices/mmc0\:0001/power/control
// MMC_CAP2_HS200_1_8V_SDR
/sys/kernel/debug/mmc0# echo $(($(cat caps2) & ~(1 << 5))) > caps2
/sys/kernel/debug/mmc0# echo on > /sys/bus/mmc/devices/mmc0\:0001/power/control
/sys/kernel/debug/mmc0# grep timing ios
timing spec: 8 (mmc DDR52)
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230929-mmc-caps-v2-2-11a4c2d94f15@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want to allow host caps to be changed dynamically via debugfs, so for
these to have an effect, ensure that the card type reselection is always
applied even if the card is old.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230929-mmc-caps-v2-1-11a4c2d94f15@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'fsl,mxs-gpio' property is not documented in gpio-mxs.yaml, but
the imx23 and imx28 dtsi describe the gpios as:
compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
This gives schema warnings like:
imx28-cfa10037.dtb: pinctrl@80018000: gpio@0:compatible: ['fsl,imx28-gpio', 'fsl,mxs-gpio'] is too long
from schema $id: http://devicetree.org/schemas/gpio/gpio-mxs.yaml#
"fsl,mxs-gpio" is only used inside pinctrl-mxs, but can be removed if
the compatible check is done against fsl,imx23-gpio and fsl,imx28-gpio.
Introduce is_mxs_gpio() and remove the need for "fsl,mxs-gpio".
Tested on a imx28-evk.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230928134321.438547-1-festevam@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add struct mcp23s08_info and simplify probe()/mcp23s08_spi_regmap_init() by
replacing match data 'type' with 'struct mcp23s08_info'.
While at it, replace 'dev_err()'->'dev_err_probe()' and drop printing
'type' in error path for i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231001150113.7752-4-biju.das.jz@bp.renesas.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simpilfy probe() by replacing device_get_match_data() and ID lookup for
retrieving match data by spi_get_device_match_data().
While at it, replace data type of variable type from 'int'->'unsigned int'
and declare variables following a reverse christmas tree order.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231001150113.7752-3-biju.das.jz@bp.renesas.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver has OF match table, still it uses ID lookup table for
retrieving match data. Currently the driver is working on the
assumption that a I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using of_device_match_data() if the devices are registered via OF.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231001150113.7752-2-biju.das.jz@bp.renesas.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the warnings of "Function parameter or member 'xxx'
not described".
>> sound/soc/fsl/mpc5200_dma.c:116: warning: Function parameter or member 'component' not described in 'psc_dma_trigger'
sound/soc/fsl/mpc5200_dma.c:116: warning: Function parameter or member 'substream' not described in 'psc_dma_trigger'
sound/soc/fsl/mpc5200_dma.c:116: warning: Function parameter or member 'cmd' not described in 'psc_dma_trigger'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310061914.jJuekdHs-lkp@intel.com/
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Fixes: 6d1048bc11 ("ASoC: fsl: mpc5200_dma: remove snd_pcm_ops")
Link: https://lore.kernel.org/r/87il7fcqm8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To use RT5682S as the codec and MAX98390 as the amp, add a new
sound card named mt8188_rt5682s.
Signed-off-by: xiazhengqiao <xiazhengqiao@huaqin.corp-partner.google.com>
Reviewed-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231010023738.8241-3-xiazhengqiao@huaqin.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string "mediatek,mt8188-rt5682s" to support new board
with rt5682s codec.
Signed-off-by: xiazhengqiao <xiazhengqiao@huaqin.corp-partner.google.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231010023738.8241-2-xiazhengqiao@huaqin.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The STM32 SDMMC peripheral (at least for the STM32F429, STM32F469 and
STM32F746, which are all the currently supported devices using periphid
0x00880180) requires DMA to be performed in peripheral flow controller
mode. From the STM32F74/5 reference manual, section 35.3.2:
"SDMMC host allows only to use the DMA in peripheral flow controller
mode. DMA stream used to serve SDMMC must be configured in peripheral
flow controller mode"
This patch adds a variant option to control peripheral flow control and
enables it for the STM32 variant.
Signed-off-by: Ben Wolsieffer <Ben.Wolsieffer@hefring.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230928135644.1489691-1-ben.wolsieffer@hefring.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* icc-misc
interconnect: imx: Replace custom implementation of COUNT_ARGS()
interconnect: msm8974: Replace custom implementation of COUNT_ARGS()
interconnect: qcom: osm-l3: Replace custom implementation of COUNT_ARGS()
interconnect: fix error handling in qnoc_probe()
interconnect: imx: Replace inclusion of kernel.h in the header
dt-bindings: interconnect: qcom,rpmh: do not require reg on SDX65 MC virt
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The MC virt interconnect in SDX65 DTSI does not have reg. Similarly in
the downstream DTS, thus assume this is an interconnect without own
dedicated IO address space. This fixes dtbs_check warnings like:
qcom-sdx65-mtp.dtb: interconnect-mc-virt: 'reg' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230827114026.47806-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add missing clk_disable_unprepare() and clk_bulk_disable_unprepare()
in the error path in qnoc_probe(). And when qcom_icc_qos_set() fails,
it needs remove nodes and disable clks.
Fixes: 2e2113c8a6 ("interconnect: qcom: rpm: Handle interface clocks")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230803130521.959487-1-yangyingliang@huawei.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Clang 17 reports:
arch/powerpc/kernel/traps.c:1167:19: error: unused function '__parse_fpscr' [-Werror,-Wunused-function]
__parse_fpscr() is called from two sites. First call is guarded
by #ifdef CONFIG_PPC_FPU_REGS
Second call is guarded by CONFIG_MATH_EMULATION which selects
CONFIG_PPC_FPU_REGS.
So only define __parse_fpscr() when CONFIG_PPC_FPU_REGS is defined.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309210327.WkqSd5Bq-lkp@intel.com/
Fixes: b6254ced4d ("powerpc/signal: Don't manage floating point regs when no FPU")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/5de2998c57f3983563b27b39228ea9a7229d4110.1695385984.git.christophe.leroy@csgroup.eu
It is not necessary to call of_match_device() in probe. If we made it to
probe, then we've already successfully matched.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231006214421.339445-1-robh@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Petr Machata says:
====================
mlxsw: Fix -Wformat-truncation warnings
Ido Schimmel writes:
Commit 6d4ab2e97d ("extrawarn: enable format and stringop overflow
warnings in W=1") enabled format warnings as part of W=1 builds,
resulting in two new warnings in mlxsw. Fix both and target at net-next
as the warnings are not indicative of actual bugs.
====================
Link: https://lore.kernel.org/r/cover.1696600763.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ethtool stats strings cannot be longer than 32 characters
('ETH_GSTRING_LEN'), including the terminating null byte. The format
string '%.29s_%.1d' can exceed this limitation if the per-TC counter
name exceeds 28 characters. Together with the underscore, the two digits
of the TC (bounded at 16) and the terminating null byte, more than 32
characters will be used.
Fix this by bounding the counter name at 28 characters which suppresses
the following build warning [1]. This does not affect ethtool output
since the longest counter name does not exceed this limitation.
[1]
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c: In function ‘mlxsw_sp_port_get_strings’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:622:58: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
622 | snprintf(*p, ETH_GSTRING_LEN, "%.29s_%.1d",
| ^
In function ‘mlxsw_sp_port_get_tc_strings’,
inlined from ‘mlxsw_sp_port_get_strings’ at drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:677:4:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:622:17: note: ‘snprintf’ output between 3 and 33 bytes into a destination of size 32
622 | snprintf(*p, ETH_GSTRING_LEN, "%.29s_%.1d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
623 | mlxsw_sp_port_hw_tc_stats[i].str, tc);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c: In function ‘mlxsw_sp_port_get_strings’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:622:58: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
622 | snprintf(*p, ETH_GSTRING_LEN, "%.29s_%.1d",
| ^
In function ‘mlxsw_sp_port_get_tc_strings’,
inlined from ‘mlxsw_sp_port_get_strings’ at drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:677:4:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c:622:17: note: ‘snprintf’ output between 3 and 33 bytes into a destination of size 32
622 | snprintf(*p, ETH_GSTRING_LEN, "%.29s_%.1d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
623 | mlxsw_sp_port_hw_tc_stats[i].str, tc);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The name of a thermal zone device cannot be longer than 19 characters
('THERMAL_NAME_LENGTH - 1'). The format string 'mlxsw-lc%d-gearbox%d'
can exceed this limitation if the maximum number of line cards and the
maximum number of gearboxes on each line card cannot be represented
using a single digit.
This is not the case with current systems nor future ones. Therefore,
increase the size of the result buffer beyond 'THERMAL_NAME_LENGTH' and
suppress the following build warning [1].
If this limitation is ever exceeded, we will know about it since the
thermal core validates the thermal device's name during registration.
[1]
drivers/net/ethernet/mellanox/mlxsw/core_thermal.c: In function ‘mlxsw_thermal_gearboxes_init.constprop’:
drivers/net/ethernet/mellanox/mlxsw/core_thermal.c:543:71: error: ‘%d’ directive output may be truncated writing between 1 and 3 bytes into a region of size between 1 and 3
[-Werror=format-truncation=]
543 | snprintf(tz_name, sizeof(tz_name), "mlxsw-lc%d-gearbox%d",
| ^~
In function ‘mlxsw_thermal_gearbox_tz_init’,
inlined from ‘mlxsw_thermal_gearboxes_init.constprop’ at drivers/net/ethernet/mellanox/mlxsw/core_thermal.c:611:9:
drivers/net/ethernet/mellanox/mlxsw/core_thermal.c:543:52: note: directive argument in the range [1, 255]
543 | snprintf(tz_name, sizeof(tz_name), "mlxsw-lc%d-gearbox%d",
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_thermal.c:543:17: note: ‘snprintf’ output between 19 and 23 bytes into a destination of size 20
543 | snprintf(tz_name, sizeof(tz_name), "mlxsw-lc%d-gearbox%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
544 | gearbox_tz->slot_index, gearbox_tz->module + 1);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the SMC protocol is built into the kernel proper while ISM is
configured to be built as module, linking the kernel fails due to
unresolved dependencies out of net/smc/smc_ism.o to
ism_get_smcd_ops, ism_register_client, and ism_unregister_client
as reported via the linux-next test automation (see link).
This however is a bug introduced a while ago.
Correct the dependency list in ISM's and SMC's Kconfig to reflect the
dependencies that are actually inverted. With this you cannot build a
kernel with CONFIG_SMC=y and CONFIG_ISM=m. Either ISM needs to be 'y',
too - or a 'n'. That way, SMC can still be configured on non-s390
architectures that do not have (nor need) an ISM driver.
Fixes: 89e7d2ba61 ("net/ism: Add new API for client registration")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/d53b5b50-d894-4df8-8969-fd39e63440ae@infradead.org/
Co-developed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20231006125847.1517840-1-gbayer@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add interconnect driver support for SDX75 platform.
* icc-sdx75
dt-bindings: interconnect: Add compatibles for SDX75
interconnect: qcom: Add SDX75 interconnect provider driver
Link: https://lore.kernel.org/r/1694614256-24109-1-git-send-email-quic_rohiagar@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>anter a commit message to explain why this merge is necessary,
The adapter->vf_mvs.l list needs to be initialized even if the list is
empty. Otherwise it will lead to crashes.
Fixes: a1cbb15c13 ("ixgbe: Add macvlan support for VF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/ZSADNdIw8zFx1xw2@kadam
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Address an issue in ksz9477_acl_move_entries() where, in the scenario
(src_idx == dst_idx), ksz9477_validate_and_get_src_count() returns 0,
leading to usage of uninitialized src_count and dst_count variables,
which causes undesired behavior as it attempts to move ACL entries
around.
Fixes: 002841be13 ("net: dsa: microchip: Add partial ACL support for ksz9477 switches")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231006115822.144152-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent NUMA hinting faulting activity is reset approximately every
VMA_PID_RESET_PERIOD milliseconds. However, if the current task has not
accessed a VMA then the reset check is missed and the reset is potentially
deferred forever. Check if the PID activity information should be reset
before checking if the current task recently trapped a NUMA hinting fault.
[ mgorman@techsingularity.net: Rewrite changelog ]
Suggested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Raghavendra K T <raghavendra.kt@amd.com>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231010083143.19593-5-mgorman@techsingularity.net
NUMA balancing skips or scans VMAs for a variety of reasons. In preparation
for completing scans of VMAs regardless of PID access, trace the reasons
why a VMA was skipped. In a later patch, the tracing will be used to track
if a VMA was forcibly scanned.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231010083143.19593-4-mgorman@techsingularity.net
The access_pids[] field name is somewhat ambiguous as no PIDs are accessed.
Similarly, it's not clear that next_pid_reset is related to access_pids[].
Rename the fields to more accurately reflect their purpose.
[ mingo: Rename in the comments too. ]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231010083143.19593-3-mgorman@techsingularity.net
The sta_himax83102 panel sometimes shows abnormally flickering
horizontal lines. The front gate output will precharge the X point of
the next pole circuit before TP(TouchPanel Enable) term starts, and wait
until the end of the TP term to resume the CLK. For this reason, the X
point must be maintained during the TP term. In abnormal case, we
measured a slight leakage at point X. This because during the TP term,
the GPW does not fully pull the VGL low, causing the TFT to not be
closed tightly.
To fix this, we completely pull GPW to VGL before entering the TP term.
This will ensure that the TFT is closed tightly and prevent the abnormal
display.
Fixes: 1bc2ef065f ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
When updating the SA, use the new update_pn flags instead of comparing the
new PN with the initial one.
Comparing the initial PN value with the new value will allow the user
to update the SA using the initial PN value as a parameter like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 off
Fixes: 8ff0ac5be1 ("net/mlx5: Add MACsec offload Tx command support")
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When updating SA, update the PN only when the update_pn flag is true.
Otherwise, the PN will be reset to its previous value using the
following command and this should not happen:
$ ip macsec set macsec0 tx sa 0 on
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use atomic_try_cmpxchg() instead of atomic_cmpxchg(*ptr, old, new) == old
in rcuref_put_slowpath(). On x86 the CMPXCHG instruction returns success in the
ZF flag, so this change saves a compare after CMPXCHG. Additionaly,
the compiler reorders some code blocks to follow likely/unlikely
annotations in the atomic_try_cmpxchg() macro, improving the code from:
9a: f0 0f b1 0b lock cmpxchg %ecx,(%rbx)
9e: 83 f8 ff cmp $0xffffffff,%eax
a1: 74 04 je a7 <rcuref_put_slowpath+0x27>
a3: 31 c0 xor %eax,%eax
to:
9a: f0 0f b1 0b lock cmpxchg %ecx,(%rbx)
9e: 75 4c jne ec <rcuref_put_slowpath+0x6c>
a0: b0 01 mov $0x1,%al
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20230509150255.3691-1-ubizjak@gmail.com
David Morley says:
====================
tcp: save flowlabel and use for receiver repathing
This patch series stores the last received ipv6 flowlabel. This last
received flowlabel is then used to help decide whether a packet is
likely an RTO retransmit or the result of a TLP. This new information
is used to better inform the flowlabel change decision for data
receivers.
====================
Link: https://lore.kernel.org/r/20231006011841.3558307-1-morleyd.kernel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit changes the data receiver repath behavior to occur after
receiving a single duplicate. This can help recover ACK connectivity
quicker if a TLP was sent along a nonworking path.
For instance, consider the case where we have an initially nonworking
forward path and reverse path and subsequently switch to only working
forward paths. Before this patch we would have the following behavior.
+---------+--------+--------+----------+----------+----------+
| Event | For FL | Rev FL | FP Works | RP Works | Data Del |
+---------+--------+--------+----------+----------+----------+
| Initial | A | 1 | N | N | 0 |
+---------+--------+--------+----------+----------+----------+
| TLP | A | 1 | N | N | 0 |
+---------+--------+--------+----------+----------+----------+
| RTO 1 | B | 1 | Y | N | 1 |
+---------+--------+--------+----------+----------+----------+
| RTO 2 | C | 1 | Y | N | 2 |
+---------+--------+--------+----------+----------+----------+
| RTO 3 | D | 2 | Y | Y | 3 |
+---------+--------+--------+----------+----------+----------+
This patch gets rid of at least RTO 3, avoiding additional unnecessary
repaths of a working forward path to a (potentially) nonworking one.
In addition, this commit changes the behavior to avoid repathing upon
rx of duplicate data if the local endpoint is in CA_Loss (in which
case the RTOs will already be changing the outgoing flowlabel).
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order to better estimate whether a data packet has been
retransmitted or is the result of a TLP, we save the last received
ipv6 flowlabel.
To make space for this field we resize the "ato" field in
inet_connection_sock as the current value of TCP_DELACK_MAX can be
fully contained in 8 bits and add a compile_time_assert ensuring this
field is the required size.
v2: addressed kernel bot feedback about dccp_delack_timer()
v3: addressed build error introduced by commit bbf80d713f ("tcp:
derive delack_max from rto_min")
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In esp_remove_trailer(), to avoid an unexpected result returned by
pskb_trim, we should check the return value of pskb_trim().
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
