Switch my mail address from a company mail to a personal one.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Improve the Kconfig help text to convey the ACE is for changing camera
sensor ownership and CSI for configuring the CSI-2 rx and tx.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The value of V4L2_CID_VBLANK control is initialized to default vblank
value of 640x480 when driver probe. When OV5640 work at DVP mode, the
control value won't update and lead to sensor can't output data if the
resolution remain the same as last time since incorrect total vertical
size. So update it when there is a new value applied.
Fixes: bce93b827d ("media: ov5640: Add VBLANK control")
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "ret = " assignment was missing, so ov13b10_power_on() is not
checked for errors. Add the assignment.
Fixes: 6e28afd152 ("media: ov13b10: add PM control support based on power resources")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Correct the driver source path specified in the MAINTAINERS file,
which was mistakenly set due to an oversight during the driver's
initial addition.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Define EP5_BUF_SIZE and EP5_TIMEOUT_MS macros to make the code
more readable.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use kmemdup() helper instead of open-coding to
simplify the code.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix a small typo in the debug message: vb2_dbuf -> vb2_qbuf
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Syzkaller reported the following issue:
UBSAN: shift-out-of-bounds in drivers/media/usb/gspca/cpia1.c:1031:27
shift exponent 245 is too large for 32-bit type 'int'
When the value of the variable "sd->params.exposure.gain" exceeds the
number of bits in an integer, a shift-out-of-bounds error is reported. It
is triggered because the variable "currentexp" cannot be left-shifted by
more than the number of bits in an integer. In order to avoid invalid
range during left-shift, the conditional expression is added.
Reported-by: syzbot+e27f3dbdab04e43b9f73@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/20230818164522.12806-1-coolrrsh@gmail.com
Link: https://syzkaller.appspot.com/bug?extid=e27f3dbdab04e43b9f73
Signed-off-by: Rajeshwar R Shinde <coolrrsh@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In case of encoded input VP9 data width that is not multiple of macroblock
size, which is 16 (e.g. 1080x1920 frames, where 1080 is multiple of 8), the
width is padded to be a multiple of macroblock size (for 1080x1920 frames,
that is 1088x1920).
The hantro_postproc_g2_enable() checks whether the encoded data width is
equal to decoded frame width, and if not, enables down-scale mode. For a
frame where input is 1080x1920 and output is 1088x1920, this is incorrect
as no down-scale happens, the frame is only padded. Enabling the down-scale
mode in this case results in corrupted frames.
Fix this by adjusting the check to test whether encoded data width is
greater than decoded frame width, and only in that case enable the
down-scale mode.
To generate input test data to trigger this bug, use e.g.:
$ gst-launch-1.0 videotestsrc ! video/x-raw,width=272,height=256,format=I420 ! \
vp9enc ! matroskamux ! filesink location=/tmp/test.vp9
To trigger the bug upon decoding (note that the NV12 must be forced, as
that assures the output data would pass the G2 postproc):
$ gst-launch-1.0 filesrc location=/tmp/test.vp9 ! matroskademux ! vp9parse ! \
v4l2slvp9dec ! video/x-raw,format=NV12 ! videoconvert ! fbdevsink
Fixes: 79c987de8b ("media: hantro: Use post processor scaling capacities")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The i.MX8MM/N/P does not define the .reset op since reset of the VPU is
done by genpd. Check whether the .reset op is defined before calling it
to avoid NULL pointer dereference.
Note that the Fixes tag is set to the commit which removed the reset op
from i.MX8M Hantro G2 implementation, this is because before this commit
all the implementations did define the .reset op.
Fixes: 6971efb70a ("media: hantro: Allow i.MX8MQ G1 and G2 to run independently")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert list_for_each() to list_for_each_entry() so that the p
list_head pointer and list_entry() call are no longer needed, which
can reduce a few lines of code. No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The last buffer from before the change must be marked,
with the V4L2_BUF_FLAG_LAST flag,
similarly to the Drain sequence above.
Meanwhile if V4L2_DEC_CMD_STOP is sent before
the source change triggered,
we need to restore the is_draing flag after
the draining in dynamic resolution change.
Fixes: b4e1fb8643 ("media: imx-jpeg: Support dynamic resolution change")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With devm_clk_get_enabled() the call to clk_disable_unprepare() can be
dropped from the error path and the remove callback.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Using kmemdup() helper function rather than implementing it again
with kmalloc() + memcpy(), which improves the code readability.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a ternary operator, the true or false judgement of which
is unnecessary in C language semantics.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a ternary operator, the true or false judgement of which
is unnecessary in C language semantics.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There are a few ternary operators, the true or false judgement of which
is unnecessary in C language semantics.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Google Boxy device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: updated to the new multi-port datastructures]
Constitution has two HDMI ports which support CEC:
Port B is EC port 0
Port A is EC port 1
This patch depends on "media: cros-ec-cec: Add Dibbi to the match
table".
Signed-off-by: Stefan Adolfsson <sadolfsson@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: updated to the new multi-port datastructures]
Dibbi has two HDMI ports which support CEC:
Port D is EC port 0
Port B is EC port 1
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a new CEC port count host command and use it to query the number of
CEC ports from the EC. If the host command is not supported then it must
be old EC firmware which only supports one port, so fall back to
assuming one port.
This patch completes support for multiple ports in cros-ec-cec.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Update the cec_dmi_match_table to allow specifying multiple HDMI
connectors for each device.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently, received messages are sent from the EC in the cec_message
MKBP event. Since the size of ec_response_get_next_data_v1 is 16 bytes,
which is also the maximum size of a CEC message, there is no space to
add a port parameter. Increasing the size of
ec_response_get_next_data_v1 is an option, but this would increase
EC-kernel traffic for all MKBP event types.
Instead, use an event to notify that data is ready, and add a new read
command to read the data.
For backwards compatibility with old EC firmware, continue to handle
cec_message events as well.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the top four bits of the cec_events MKBP event to store the port
number.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a v1 of the CEC write command which contains a port parameter. Check
which versions of the write command the EC supports and use the highest
supported version. If it only supports v0, check that there is only one
port. With v0, the EC will assume all write commands are for port 0.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reuse the top four bits of the cmd field to specify the port number.
The reason for doing this as opposed to adding a separate uint8_t field
is it avoids the need to add new versions of these commands. The change
is backwards compatible since these bits were previously always zero, so
the default behaviour is to always operate on port 0.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
To support multiple CEC ports, change cros_ec_cec to contain an array of
ports, each with their own CEC adapter, etc.
For now, only create a single port and use that port everywhere, so
there is no functional change. Support for multiple ports will be added
in the following patches.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the cros_ec_cmd helper function to reduce the amount of boilerplate
when sending host commands.
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Platforms with qcom-camss use CSI-2, which means 1X16 is more correct
than 2X8. The fact that qcom-camss supported only 2X8 meant it was
incompatible with camera sensors it should have been compatible with.
For example, the ov5645 driver (correctly) reports that its format is
UYVY8_1X16 (after ba449bb562).
Since qcom-camss only supports 2X8, the qcom-camss system is
incompatible with the ov5645 driver, even though they should be
compatible.
This patch replaces all uses of UYVY8_2X8/VYUY8_2X8/YUYV8_2X8/YVYU8_2X8
with the equivalent 1X16 formats.
Signed-off-by: Martin Dørum <dorum@noisolation.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Allow the interconnect properties, which have been in use for ages.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
Tested with:
RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is required for VCs with a larger address than two bits.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE BIT(7)
disjunction for gen2 ? BIT(7) : is a nop we are setting the same bit
either way.
Fixes: 4abb21309f ("media: camss: csiphy: Move to hardcode CSI Clock Lane number")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
vfe-480 is copied from vfe-17x and has the same racy idle timeout bug as in
17x.
Fix the vfe_disable_output() logic to no longer be racy and to conform
to the 17x way of quiescing and then resetting the VFE.
Fixes: 4edc8eae71 ("media: camss: Add initial support for VFE hardware version Titan 480")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Right now we never release the power-domains properly on the error path.
Add a routine to be reused for this purpose and appropriate jumps in
probe() to run that routine where necessary.
Fixes: 2f6f8af672 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Previously the jump label err_cleanup was used higher in the probe()
function to release the async notifier however the async notifier
registration was moved later in the code rendering the previous four jumps
redundant.
Rename the label from err_cleanup to err_v4l2_device_unregister to capture
what the jump does.
Fixes: 51397a4ec75d ("media: qcom: Initialise V4L2 async notifier later")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix old name in commit log: err_v4l2_device_register -> err_v4l2_device_unregister]
We need to make sure camss_configure_pd() happens before
camss_register_entities() as the vfe_get() path relies on the pointer
provided by camss_configure_pd().
Fix the ordering sequence in probe to ensure the pointers vfe_get() demands
are present by the time camss_register_entities() runs.
In order to facilitate backporting to stable kernels I've moved the
configure_pd() call pretty early on the probe() function so that
irrespective of the existence of the old error handling jump labels this
patch should still apply to -next circa Aug 2023 to v5.13 inclusive.
Fixes: 2f6f8af672 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
fsl,imx25-gpio and fsl,imx27-gpio are not documented, causing schema
warnings.
fsl,imx25-gpio is compatible with fsl,imx35-gpio and fsl,imx27-gpio
is compatible with fsl,imx21-gpio.
Document them accordingly.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The drivers uses a mutex and I2C bus access in its PMIC EIC chip
get implementation. This means these functions can sleep and the PMIC EIC
chip should set the can_sleep property to true.
This will ensure that a warning is printed when trying to get the
value from a context that potentially can't sleep.
Fixes: 348f3cde84 ("gpio: Add Spreadtrum PMIC EIC driver support")
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This patch was to add loongson 2k0500, 2k2000 and 3a5000 gpio chip
driver support and define inten_offset attibute to enable gpio chip
interrupt.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The Qualcomm QCM6490 platform uses the qcom-cpufreq-hw driver, so add it
to the cpufreq-dt-platdev driver's blocklist.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This rewrites the IXP4xx GPIO bindings to use YAML schema,
and adds two new properties to enable fixed clock output on
pins 14 and 15.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
timbgpio_gpio_set()
--> timbgpio_update_bit()
--> spin_lock(&tgpio->lock)
<interrupt>
--> timbgpio_irq_disable()
--> spin_lock_irqsave(&tgpio->lock)
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Create buffers with cache coherency on the CPU side (write-back) while
disabling snooping on the VPU side. These buffers require an explicit
cache flush after each CPU-side modification.
Configuring pages as write-combined may introduce significant delays,
potentially taking hundreds of milliseconds for 64 MB buffers.
Added internal DRM_IVPU_BO_NOSNOOP mask which disables snooping on the
VPU side. Allocate FW runtime memory buffer (64 MB) as cached with
snooping-disabled.
This fixes random long FW loading times and boot params memory
corruption on warmboot (due to missed wmb).
Fixes: 02d5b0aacd ("accel/ivpu: Implement firmware parsing and booting")
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926120943.GD846747@linux.intel.com
