Since both 'ar9550_hw_get_modes_txgain_index()' and
'ar9561_hw_get_modes_txgain_index()' never returns
negative values, prefer 'u32' over 'int' and adjust
'ar9003_hw_process_ini()' accordingly.
Suggested-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230823182401.196270-2-dmantipov@yandex.ru
Since commit 8896934c16 ("ath9k_hw: remove direct accesses to channel
mode flags") changes 'ar9550_hw_get_modes_txgain_index()' so it never
returns -EINVAL, and 'ar9561_hw_get_modes_txgain_index()' never returns
negative value too, an extra check in 'ar9003_hw_process_ini()' may be
dropped.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230823182401.196270-1-dmantipov@yandex.ru
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230802085852.19821-3-quic_mdharane@quicinc.com
Fix WARN_ON() from ath12k_mac_update_vif_chan() if vdev is not up.
Since change_chanctx can be called even before vdev_up.
Do vdev stop followed by a vdev start in case of vdev is down.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230802085852.19821-2-quic_mdharane@quicinc.com
The buck and linear range LDO (VSRAM_*) regulators share one set of ops.
This set includes support for get/set mode. However this only makes
sense for buck regulators, not LDOs. The callbacks were not checking
whether the register offset and/or mask for mode setting was valid or
not. This ends up making the kernel report "normal" mode operation for
the LDOs.
Create a new set of ops without the get/set mode callbacks for the
linear range LDO regulators.
Fixes: f67ff1bd58 ("regulator: mt6358: Add support for MT6358 regulator")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230920085336.136238-1-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a large collection of fixes, with numbers boosted by multiple
vendors sending multi-patch serieses. Nothing super major, and also one
device quirk.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmUK6tUACgkQJNaLcl1U
h9CF5Af+IhyN4/WaqDOl6hgKJr206SDHkiW5SAq+cRMsTGWLzM32MXDYxHg21Lke
hD6weld3cjvN/yqPOxLGS6+Sf5S6BXIdSmTrjVKyrRag6qn+ArzzO2sQpOWdeYs3
SJAa36Ias/Mz8IPNOZpoQLdF8p7ncXYqUyqnx579pPMO5P2IeLSf0MbBdAxxrw8V
Q0OOulaLxwKaDx2ss0mL4KAnfbgYe8e9c0xYhyBCNElAU/m+FCWazslXF5tOWkjI
vZFmqJ1jBsCXLctWnCceER4A/nTK2m8WIJ6ep97cuD2dhVuzJxY3BmhN+aL2zgDQ
dvl5f8gv8PhYX2aM8gCXP5SE+Lczvg==
=MePv
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.6
Quite a large collection of fixes, with numbers boosted by multiple
vendors sending multi-patch serieses. Nothing super major, and also one
device quirk.
Convert list_for_each() to list_for_each_entry() so that the p
list_head pointer and list_entry() call are no longer needed, which
can reduce a few lines of code. No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230830090344.528818-1-ruanjinjie@huawei.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The typical use of kmalloc_size_roundup() is:
ptr = kmalloc(sz = kmalloc_size_roundup(size), ...);
if (!ptr) return -ENOMEM.
This means it is vitally important that the returned value isn't less
than the argument even if the argument is insane.
In particular if kmalloc_slab() fails or the value is above
(MAX_ULONG - PAGE_SIZE) zero is returned and kmalloc() will return
its single zero-length buffer ZERO_SIZE_PTR.
Fix this by returning the input size if the size exceeds
KMALLOC_MAX_SIZE. kmalloc() will then return NULL as the size really is
too big.
kmalloc_slab() should not normally return NULL, unless called too early.
Again, returning zero is not the correct action as it can be in some
usage scenarios stored to a variable and only later cause kmalloc()
return ZERO_SIZE_PTR and subsequent crashes on access. Instead we can
simply stop checking the kmalloc_slab() result completely, as calling
kmalloc_size_roundup() too early would then result in an immediate crash
during boot and the developer noticing an issue in their code.
[vbabka@suse.cz: remove kmalloc_slab() result check, tweak comments and
commit log]
Fixes: 05a940656e ("slab: Introduce kmalloc_size_roundup()")
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
The SMMU GDSC doesn't have to be ALWAYS-ON and shouldn't feature the
HW_CTRL flag (it's separate from hw_ctrl_addr). In addition to that,
it should feature a cxc entry for bimc_smmu_axi_clk and be marked as
votable.
Fix all of these issues.
Fixes: d14b15b593 ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20230531-topic-8998_mmssclk-v3-5-ba1b1fd9ee75@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some branch clocks are governed externally and we're only supposed to
send a request concerning their shutdown, not actually ensure it happens.
Use the BRANCH_HALT_SKIP define to skip checking the halt bit.
Fixes: d14b15b593 ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230531-topic-8998_mmssclk-v3-4-ba1b1fd9ee75@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We've changed the holder of the block device which has consequences.
Document this clearly and in detail so filesystem and vfs developers
have a proper digital paper trail.
Signed-off-by: Christian Brauner <brauner@kernel.org>
We've changed the order of opening block devices and superblock
handling. Let's document this so filesystem and vfs developers have
a proper digital paper trail.
Signed-off-by: Christian Brauner <brauner@kernel.org>
This code duplication was introduced by commit a194dfe6e6 ("pipe:
Rearrange sequence in pipe_write() to preallocate slot"), but since
the pipe's mutex is locked, nobody else can modify the value
meanwhile.
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Message-Id: <20230919074045.1066796-1-max.kellermann@ionos.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
When writing back an inode and performing an fsync on it concurrently, a
deadlock issue may arise as shown below. In each writeback iteration, a
clean inode is requeued to the wb->b_dirty queue due to non-zero
pages_skipped, without anything actually being written. This causes an
infinite loop and prevents the plug from being flushed, resulting in a
deadlock. We now avoid requeuing the clean inode to prevent this issue.
wb_writeback fsync (inode-Y)
blk_start_plug(&plug)
for (;;) {
iter i-1: some reqs with page-X added into plug->mq_list // f2fs node page-X with PG_writeback
filemap_fdatawrite
__filemap_fdatawrite_range // write inode-Y with sync_mode WB_SYNC_ALL
do_writepages
f2fs_write_data_pages
__f2fs_write_data_pages // wb_sync_req[DATA]++ for WB_SYNC_ALL
f2fs_write_cache_pages
f2fs_write_single_data_page
f2fs_do_write_data_page
f2fs_outplace_write_data
f2fs_update_data_blkaddr
f2fs_wait_on_page_writeback
wait_on_page_writeback // wait for f2fs node page-X
iter i:
progress = __writeback_inodes_wb(wb, work)
. writeback_sb_inodes
. __writeback_single_inode // write inode-Y with sync_mode WB_SYNC_NONE
. . do_writepages
. . f2fs_write_data_pages
. . . __f2fs_write_data_pages // skip writepages due to (wb_sync_req[DATA]>0)
. . . wbc->pages_skipped += get_dirty_pages(inode) // wbc->pages_skipped = 1
. if (!(inode->i_state & I_DIRTY_ALL)) // i_state = I_SYNC | I_SYNC_QUEUED
. total_wrote++; // total_wrote = 1
. requeue_inode // requeue inode-Y to wb->b_dirty queue due to non-zero pages_skipped
if (progress) // progress = 1
continue;
iter i+1:
queue_io
// similar process with iter i, infinite for-loop !
}
blk_finish_plug(&plug) // flush plug won't be called
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230916045131.957929-1-guochunhai@vivo.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct kioctx_table.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: linux-aio@kvack.org
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Message-Id: <20230915201413.never.881-kees@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
If we fail filemap_write_and_wait_range() on the range the buffered write went
into, we only report the "number of bytes which we direct-written", to quote
the comment in there. Which is fine, but buffered write has already advanced
iocb->ki_pos, so we need to roll that back. Otherwise we end up with e.g.
write(2) advancing position by more than the amount it reports having written.
Fixes: 182c25e9c1 "filemap: update ki_pos in generic_perform_write"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Message-Id: <20230827214518.GU3390869@ZenIV>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add function prototype for gunzip() to the boot library code and make
exit() and zalloc() static.
arch/xtensa/boot/lib/zmem.c:8:6: warning: no previous prototype for 'exit' [-Wmissing-prototypes]
8 | void exit (void)
arch/xtensa/boot/lib/zmem.c:13:7: warning: no previous prototype for 'zalloc' [-Wmissing-prototypes]
13 | void *zalloc(unsigned size)
arch/xtensa/boot/lib/zmem.c:35:6: warning: no previous prototype for 'gunzip' [-Wmissing-prototypes]
35 | void gunzip (void *dst, int dstlen, unsigned char *src, int *lenp)
Fixes: 4bedea9454 ("xtensa: Architecture support for Tensilica Xtensa Part 2")
Fixes: e7d163f766 ("xtensa: Removed local copy of zlib and fixed O= support")
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Even when a variant has one or more of these defines set to 1, the
multiplier code paths are not used. Change the expression so that the
correct code paths are used.
arch/xtensa/lib/umulsidi3.S:44:38: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
44 | #if defined(__XTENSA_CALL0_ABI__) && XCHAL_NO_MUL
arch/xtensa/lib/umulsidi3.S:145:38: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
145 | #if defined(__XTENSA_CALL0_ABI__) && XCHAL_NO_MUL
arch/xtensa/lib/umulsidi3.S:159:5: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
159 | #if XCHAL_NO_MUL
Fixes: 8939c58d68 ("xtensa: add __umulsidi3 helper")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-16-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Drop the -I<include-dir> options to prevent build warnings since there
is not boot/include directory:
cc1: warning: arch/xtensa/boot/include: No such file or directory [-Wmissing-include-dirs]
Fixes: 437374e9a9 ("restore arch/{ppc/xtensa}/boot cflags")
Fixes: 4bedea9454 ("xtensa: Architecture support for Tensilica Xtensa Part 2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-15-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Make 2 functions static to prevent build warnings:
arch/xtensa/platforms/iss/network.c:204:16: warning: no previous prototype for 'tuntap_protocol' [-Wmissing-prototypes]
204 | unsigned short tuntap_protocol(struct sk_buff *skb)
arch/xtensa/platforms/iss/network.c:444:6: warning: no previous prototype for 'iss_net_user_timer_expire' [-Wmissing-prototypes]
444 | void iss_net_user_timer_expire(struct timer_list *unused)
Fixes: 7282bee787 ("xtensa: Architecture support for Tensilica Xtensa Part 8")
Fixes: d8479a21a9 ("xtensa: Convert timers to use timer_setup()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-14-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add the prototype for check_tlb_sanity() to <asm/tlb.h> and use that
header to prevent a build warning:
arch/xtensa/mm/tlb.c:273:6: warning: no previous prototype for 'check_tlb_sanity' [-Wmissing-prototypes]
273 | void check_tlb_sanity(void)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-13-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add the prototype for restore_dbreak() to <asm/hw_breakpoint.h> and use
that header in hw_breakpoint.c to prevent a build warning:
arch/xtensa/kernel/hw_breakpoint.c:263:6: warning: no previous prototype for 'restore_dbreak' [-Wmissing-prototypes]
263 | void restore_dbreak(void)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-12-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use <asm/smp.h> to provide the prototype for secondary_start_kernel().
Use <linux/profile.h> to provide the prototype for
setup_profiling_timer().
arch/xtensa/kernel/smp.c:119:6: warning: no previous prototype for 'secondary_start_kernel' [-Wmissing-prototypes]
119 | void secondary_start_kernel(void)
arch/xtensa/kernel/smp.c:461:5: warning: no previous prototype for 'setup_profiling_timer' [-Wmissing-prototypes]
461 | int setup_profiling_timer(unsigned int multiplier)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-11-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add <linux/irqchips/xtensa-mx.h> to provide the function prototype to
prevent a build warning:
drivers/irqchip/irq-xtensa-mx.c:166:12: warning: no previous prototype for 'xtensa_mx_init_legacy' [-Wmissing-prototypes]
166 | int __init xtensa_mx_init_legacy(struct device_node *interrupt_parent)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Message-Id: <20230920052139.10570-10-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use <linux/cpu.h> to provide the prototype for trap_init(), to prevent
a build warning:
arch/xtensa/kernel/traps.c:484:13: warning: no previous prototype for 'trap_init' [-Wmissing-prototypes]
484 | void __init trap_init(void)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-9-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use <asm/ftrace.h> to prevent a build warning:
arch/xtensa/kernel/stacktrace.c:263:15: warning: no previous prototype for 'return_address' [-Wmissing-prototypes]
263 | unsigned long return_address(unsigned level)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-8-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add <asm/syscall.h> to satisfy the xtensa_rt_sigreturn() prototype
warning.
Add <asm/processor.h> to satisfy the do_notify_resume() prototype
warning.
arch/xtensa/kernel/signal.c:246:17: warning: no previous prototype for 'xtensa_rt_sigreturn' [-Wmissing-prototypes]
arch/xtensa/kernel/signal.c:525:6: warning: no previous prototype for 'do_notify_resume' [-Wmissing-prototypes]
525 | void do_notify_resume(struct pt_regs *regs)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-7-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add the prototype for init_arch() to asm/processor.h to prevent a
build warning:
arch/xtensa/kernel/setup.c:244:13: warning: no previous prototype for 'init_arch' [-Wmissing-prototypes]
244 | void __init init_arch(bp_tag_t *bp_start)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-6-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add prototype for do_syscall_trace_enter() to asm/ptrace.h.
Move prototype for do_syscall_trace_leave() there to be consistent.
Fixes a build warning:
arch/xtensa/kernel/ptrace.c:545:5: warning: no previous prototype for 'do_syscall_trace_enter' [-Wmissing-prototypes]
545 | int do_syscall_trace_enter(struct pt_regs *regs)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-5-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use <asm/traps.h> to provide the function prototype for do_IRQ()
to prevent a build warning:
arch/xtensa/kernel/irq.c:34:17: warning: no previous prototype for 'do_IRQ' [-Wmissing-prototypes]
34 | asmlinkage void do_IRQ(int hwirq, struct pt_regs *regs)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-4-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use <asm/traps.h> to provide the function prototype for do_page_fault()
to prevent a build warning:
arch/xtensa/mm/fault.c:87:6: warning: no previous prototype for 'do_page_fault' [-Wmissing-prototypes]
87 | void do_page_fault(struct pt_regs *regs)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-3-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
When variant FSF is set, XCHAL_HAVE_DIV32 is not defined. Add default
definition for that macro to prevent build warnings:
arch/xtensa/lib/divsi3.S:9:5: warning: "XCHAL_HAVE_DIV32" is not defined, evaluates to 0 [-Wundef]
9 | #if XCHAL_HAVE_DIV32
arch/xtensa/lib/modsi3.S:9:5: warning: "XCHAL_HAVE_DIV32" is not defined, evaluates to 0 [-Wundef]
9 | #if XCHAL_HAVE_DIV32
Fixes: 173d668138 ("xtensa: remove extra header files")
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: lore.kernel.org/r/202309150556.t0yCdv3g-lkp@intel.com
The DSI horizontal timing calculations done by the driver seem to often
lead to underflows or overflows, depending on the videomode.
There are two main things the current driver doesn't seem to get right:
DSI HSW and HFP, and VSDly. However, even following Toshiba's
documentation it seems we don't always get a working display.
This patch attempts to fix the horizontal timings for DSI event mode, and
on a system with a DSI->HDMI encoder, a lot of standard HDMI modes now
seem to work. The work relies on Toshiba's documentation, but also quite
a bit on empirical testing.
This also adds timing related debug prints to make it easier to improve
on this later.
The DSI pulse mode has only been tested with a fixed-resolution panel,
which limits the testing of different modes on DSI pulse mode. However,
as the VSDly calculation also affects pulse mode, so this might cause a
regression.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-12-31725f008a50@ideasonboard.com
The tc358768_ns_to_cnt() is, most likely, supposed to do a div-round-up
operation, but it misses subtracting one from the dividend.
Fix this by just using DIV_ROUND_UP().
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-11-31725f008a50@ideasonboard.com
The driver defines TC358768_PRECISION as 1000, and uses "nsk" to refer
to clock periods. The original author does not remember where all this
came from. Effectively the driver is using picoseconds as the unit for
clock periods, yet referring to them by "nsk".
Clean this up by just saying the periods are in picoseconds.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-10-31725f008a50@ideasonboard.com
The Toshiba documentation talks about HSByteClk when referring to the
DSI HS byte clock, whereas the driver uses 'dsibclk' name. Also, in a
few places the driver calculates the byte clock from the DSI clock, even
if the byte clock is already available in a variable.
To align the driver with the documentation, change the 'dsibclk'
variable to 'hsbyteclk'. This also make it easier to visually separate
'dsibclk' and 'dsiclk' variables.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-9-31725f008a50@ideasonboard.com
Simplify the code by capturing the priv->dev value to dev variable, and
use it.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-8-31725f008a50@ideasonboard.com
The driver debug prints DSI related timings as raw register values in
hex. It is much more useful to see the "logical" value of the timing,
not the register value.
Change the prints to print the values separately, in case a single
register contains multiple values, and use %u to have it in a more human
consumable form.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-7-31725f008a50@ideasonboard.com
The TC358768 documentation uses HFP, HBP, etc. values to deal with the
video mode, while the driver currently uses the DRM display mode
(htotal, hsync_start, etc).
Change the driver to convert the DRM display mode to struct videomode,
which then allows us to use the same units the documentation uses. This
makes it much easier to work on the code when using the TC358768
documentation as a reference.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-6-31725f008a50@ideasonboard.com
As is quite common, some of TC358768's PLL register fields are to be
programmed with (value - 1). Specifically, the FBD and PRD, multiplier
and divider, are such fields.
However, what the driver currently does is that it considers that the
formula used for PLL rate calculation is:
RefClk * [(FBD + 1)/ (PRD + 1)] * [1 / (2^FRS)]
where FBD and PRD are values directly from the registers, while a more
sensible way to look at it is:
RefClk * FBD / PRD * (1 / (2^FRS))
and when the FBD and PRD values are written to the registers, they will
be subtracted by one.
Change the driver accordingly, as it simplifies the PLL code.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-5-31725f008a50@ideasonboard.com
The driver has a few places where it does:
if (thing_is_enabled_in_config)
update_thing_bit_in_hw()
This means that if the thing is _not_ enabled, the bit never gets
cleared. This affects the h/vsyncs and continuous DSI clock bits.
Fix the driver to always update the bit.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-4-31725f008a50@ideasonboard.com
As the TC358768 is a DPI to DSI bridge, the DSI side does not need to
define h/v sync polarities. This means that sometimes we have a mode
without defined sync polarities, which does not work on the DPI side.
Add a mode_fixup hook to default to positive sync polarities.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-3-31725f008a50@ideasonboard.com
smatch reports:
drivers/gpu/drm/bridge/tc358768.c:223 tc358768_update_bits() error: uninitialized symbol 'orig'.
Fix this by bailing out from tc358768_update_bits() if the
tc358768_read() produces an error.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-2-31725f008a50@ideasonboard.com
The polarities of the V- and H-sync signals are encoded as flags in the
display mode, so use the existing information to setup the signals for
the RGB interface.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
[tomi.valkeinen@ideasonboard.com: default to positive sync]
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-1-31725f008a50@ideasonboard.com
Since debugfs_create_file() return ERR_PTR and never return NULL, so use
IS_ERR() to check it instead of checking NULL.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919050651.962694-1-ruanjinjie@huawei.com
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct brcmf_fw_request.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Hector Martin <marcan@marcan.st>
Cc: "Alvin Šipraga" <alsi@bang-olufsen.dk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: SHA-cyfmac-dev-list@infineon.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230915200552.never.642-kees@kernel.org
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct brcmf_gscan_config.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Hector Martin <marcan@marcan.st>
Cc: Ryohei Kondo <ryohei.kondo@cypress.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: SHA-cyfmac-dev-list@infineon.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230915200542.never.417-kees@kernel.org
