Introduce partial AMSDU offload support for MT7988 SoC in order to merge
in hw packets belonging to the same AMSDU before passing them to the
WLAN nic.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Refactor mtk_wed_check_wfdma_rx_fill() in order to be reused adding HW
receive offload support for MT7988 SoC.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to MT7986 and MT7622, enable Wireless Ethernet Ditpatcher for
MT7988 in order to offload traffic forwarded from LAN/WLAN to WLAN/LAN
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix MTK_WED_EXT_INT_STATUS_RX_FBUF_LO_TH and
MTK_WED_EXT_INT_STATUS_RX_FBUF_HI_TH definitions for MT7986 (MT7986 is
the only SoC to use them).
Fixes: de84a090d9 ("net: ethernet: mtk_eth_wed: add wed support for mt7986 chipset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make mtk_wed_wo_memory_region optionals.
This is a preliminary patch to introduce Wireless Ethernet Dispatcher
support for MT7988 SoC since MT7988 WED fw image will have a different
layout.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove mtk_wed_wo_memory_region boot structure in mtk_wed_wo.
This is a preliminary patch to introduce WED support for MT7988 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce mtk_wed_buf structure to store both virtual and physical
addresses allocated in mtk_wed_tx_buffer_alloc() routine. This is a
preliminary patch to add WED support for MT7988 SoC since it relies on a
different dma descriptor layout not storing page dma addresses.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename mtk_rxbm_desc structure in mtk_wed_bm_desc since it will be used
even on tx side by MT7988 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Check if rx offload is supported running mtk_wed_get_rx_capa routine
before configuring it. This is a preliminary patch to introduce Wireless
Ethernet Dispatcher (WED) support for MT7988 SoC.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to mtk_eth_soc, introduce the following wed versioning
utility routines:
- mtk_wed_is_v1
- mtk_wed_is_v2
This is a preliminary patch to introduce WED support for MT7988 SoC
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce MT7988 SoC compatibility string in mtk_wed binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce MT7988 SoC compatibility string in mt7986-wo-ccif binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We have data-races while reading np->srcprefs
Switch the field to a plain byte, add READ_ONCE()
and WRITE_ONCE() annotations where needed,
and IPV6_ADDR_PREFERENCES setsockopt() can now be lockless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230918142321.1794107-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are several ways a thread's shadow stacks can get unmapped. This
can happen on exit or exec, as well as error handling in exec or clone.
The task struct already keeps track of the thread's shadow stack. Use the
size variable to keep track of if the shadow stack has already been freed.
When an attempt to double unmap the thread shadow stack is caught, warn
about it and abort the operation.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: H.J. Lu <hjl.tools@gmail.com>
Link: https://lore.kernel.org/all/20230908203655.543765-4-rick.p.edgecombe%40intel.com
When clone fails after the shadow stack is allocated, any allocated shadow
stack is cleaned up in exit_thread() in copy_process(). So the logic in
copy_thread() is unneeded, and also will not handle failures that happen
outside of copy_thread().
In addition, since there is a second attempt to unmap the same shadow
stack, there is a race where an newly mapped region could get unmapped.
So remove the logic in copy_thread() and rely on exit_thread() to handle
clone failure.
Fixes: b2926a36b9 ("x86/shstk: Handle thread shadow stack")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: H.J. Lu <hjl.tools@gmail.com>
Link: https://lore.kernel.org/all/20230908203655.543765-3-rick.p.edgecombe%40intel.com
Shadow stacks are allocated automatically and freed on exit, depending
on the clone flags. The two cases where new shadow stacks are not
allocated are !CLONE_VM (fork()) and CLONE_VFORK (vfork()). For
!CLONE_VM, although a new stack is not allocated, it can be freed normally
because it will happen in the child's copy of the VM.
However, for CLONE_VFORK the parent and the child are actually using the
same shadow stack. So the kernel doesn't need to allocate *or* free a
shadow stack for a CLONE_VFORK child. CLONE_VFORK children already need
special tracking to avoid returning to userspace until the child exits or
execs. Shadow stack uses this same tracking to avoid freeing CLONE_VFORK
shadow stacks.
However, the tracking is not setup until the clone has succeeded
(internally). Which means, if a CLONE_VFORK fails, the existing logic will
not know it is a CLONE_VFORK and proceed to unmap the parents shadow stack.
This error handling cleanup logic runs via exit_thread() in the
bad_fork_cleanup_thread label in copy_process(). The issue was seen in
the glibc test "posix/tst-spawn3-pidfd" while running with shadow stack
using currently out-of-tree glibc patches.
Fix it by not unmapping the vfork shadow stack in the error case as well.
Since clone is implemented in core code, it is not ideal to pass the clone
flags along the error path in order to have shadow stack code have
symmetric logic in the freeing half of the thread shadow stack handling.
Instead use the existing state for thread shadow stacks to track whether
the thread is managing its own shadow stack. For CLONE_VFORK, simply set
shstk->base and shstk->size to 0, and have it mean the thread is not
managing a shadow stack and so should skip cleanup work. Implement this
by breaking up the CLONE_VFORK and !CLONE_VM cases in
shstk_alloc_thread_stack() to separate conditionals since, the logic is
now different between them. In the case of CLONE_VFORK && !CLONE_VM, the
existing behavior is to not clean up the shadow stack in the child (which
should go away quickly with either be exit or exec), so maintain that
behavior by handling the CLONE_VFORK case first in the allocation path.
This new logioc cleanly handles the case of normal, successful
CLONE_VFORK's skipping cleaning up their shadow stack's on exit as well.
So remove the existing, vfork shadow stack freeing logic. This is in
deactivate_mm() where vfork_done is used to tell if it is a vfork child
that can skip cleaning up the thread shadow stack.
Fixes: b2926a36b9 ("x86/shstk: Handle thread shadow stack")
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: H.J. Lu <hjl.tools@gmail.com>
Link: https://lore.kernel.org/all/20230908203655.543765-2-rick.p.edgecombe%40intel.com
Unaccepted table is now allocated from EFI_ACPI_RECLAIM_MEMORY. It
translates into E820_TYPE_ACPI, which is not added to memblock and
therefore not mapped in the direct mapping.
This causes a crash on the first touch of the table.
Use memblock_add() to make sure that the table is mapped in direct
mapping.
Align the range to the nearest page borders. Ranges smaller than page
size are not mapped.
Fixes: e7761d827e ("efi/unaccepted: Use ACPI reclaim memory for unaccepted memory table")
Reported-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Convert iomap_unshare_iter to create large folios if possible, since the
write and zeroing paths already do that. I think this got missed in the
conversion of the write paths that landed in 6.6-rc1.
Cc: ritesh.list@gmail.com, willy@infradead.org
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
smb3_smbd_connect_done and smb3_smbd_connect_err
To improve debugging of RDMA issues add those two. We already
had dynamic tracepoints for non-RDMA connect done and error cases.
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The Atmel AT26DF321 and AT25DF321 have the same ID. Both were just
discovered by reading their IDs, that is, there is no probing by name.
Thus only the first one (the AT25DF321) in the list was ever probed.
Luckily, the AT25DF is also the newer series. Drop the AT26DF321.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-40-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-39-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-38-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-37-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-36-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-35-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-34-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-33-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-32-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The flash ID is the new primary key into our database. Sort the entry by
it. Keep the most specific ones first, because there might be ID
collisions between shorter and longer ones.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-31-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
There won't be any new entries, nor are the entries that much different
and the very odd page and sector sizes make the new format hard to read.
Therefore, convert the old S3AN_INFO() macro.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-29-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
After all the preparation, it is now time to introduce the new macros to
specify flashes in our database: SNOR_ID() and SNOR_OTP(). An flash_info
entry might now look like:
{
.id = SNOR_ID(0xef, 0x60, 0x16),
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
.flags = SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB,
}
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-15-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Move the OTP ops out of the flash_info structure. Besides of saving some
space, there will be a new macro SNOR_OTP() which can be used to set the
ops:
.otp = SNOR_OTP(...),
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-14-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Create a new structure to hold a flash ID and its length. The goal is to
have a new macro SNOR_ID() which can have a flexible id length. This way
we can get rid of all the individual INFOx() macros.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-13-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The id will be converted to an own structure. To differentiate between
flashes with and without IDs, introduce a temporary macro INFO0() and
convert all flashes with no ID to use it. The difference between INFO0()
and INFOx() is that the former, doesn't have a pointer to the id
structure. Something which isn't possible to do within the INFOx()
macro.
After the flash_info conversion, that macro will be removed along with
all the other INFOx() macros.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20230807-mtd-flash-info-db-rework-v3-12-e60548861b10@kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
