Oleksij Rempel says:
====================
net: dsa: microchip: add drive strength support
changes v5:
- rename milliamp to microamp
- do not expect negative error code on snprintf
- set coma after last struct element
- rename found to have_any_prop
changes v4:
- integrate microchip feedback to the ksz9477_drive_strengths comment.
- add Reviewed-by: Rob Herring <robh@kernel.org>
changes v3:
- yaml: use enum instead of min/max
- do not use snprintf() on overlapping buffer.
- unify ksz_drive_strength_to_reg() and ksz_drive_strength_error(). Make
it usable for KSZ9477 and KSZ8830 variants.
- use ksz_rmw8() in ksz9477_drive_strength_write()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based drive strength configuration support. It is needed to
pass EMI validation on our hardware.
Configuration values are based on the vendor's reference driver.
Tested on KSZ9563R.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend device tree bindings to support drive strength configuration for the
ksz* switches. Introduced properties:
- microchip,hi-drive-strength-microamp: Controls the drive strength for
high-speed interfaces like GMII/RGMII and more.
- microchip,lo-drive-strength-microamp: Governs the drive strength for
low-speed interfaces such as LEDs, PME_N, and others.
- microchip,io-drive-strength-microamp: Controls the drive strength for
for undocumented Pads on KSZ88xx variants.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an XDP redirect happens before the link is ready, that
transmission will not finish and will timeout, causing an adapter
reset. If the redirects do not stop, the adapter will not stop
resetting.
Wait for the driver to signal that there's a carrier before allowing
transmissions to proceed.
Previous code was relying that when __IGC_DOWN is cleared, the NIC is
ready to transmit as all the queues are ready, what happens is that
the carrier presence will only be signaled later, after the watchdog
workqueue has a chance to run. And during this interval (between
clearing __IGC_DOWN and the watchdog running) if any transmission
happens the timeout is emitted (detected by igc_tx_timeout()) which
causes the reset, with the potential for the infinite loop.
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Closes: https://lore.kernel.org/netdev/0caf33cf6adb3a5bf137eeaa20e89b167c9986d5.camel@ericsson.com/
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bitmap_zalloc() and bitmap_free() instead of hand-writing them.
It is less verbose and it improves the type checking and semantic.
While at it, add missing header inclusion (should be bitops.h,
but with the above change it becomes bitmap.h).
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230911154534.4174265-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we fetch sense data for a _successful_ command if either:
1) Command was NCQ and ATA_DFLAG_CDL_ENABLED flag set (flag
ATA_DFLAG_CDL_ENABLED will only be set if the Successful NCQ command
sense data supported bit is set); or
2) Command was non-NCQ and regular sense data reporting is enabled.
This means that case 2) will trigger for a non-NCQ command which has
ATA_SENSE bit set, regardless if CDL is enabled or not.
This decision was by design. If the device reports that it has sense data
available, it makes sense to fetch that sense data, since the sk/asc/ascq
could be important information regardless if CDL is enabled or not.
However, the fetching of sense data for a successful command is done via
ATA EH. Considering how intricate the ATA EH is, we really do not want to
invoke ATA EH unless absolutely needed.
Before commit 18bd7718b5 ("scsi: ata: libata: Handle completion of CDL
commands using policy 0xD") we never fetched sense data for successful
commands.
In order to not invoke the ATA EH unless absolutely necessary, even if the
device claims support for sense data reporting, only fetch sense data for
successful (NCQ and non-NCQ commands) commands that are using CDL.
[Damien] Modified the check to test the qc flag ATA_QCFLAG_HAS_CDL
instead of the device support for CDL, which is implied for commands
using CDL.
Fixes: 3ac873c76d ("ata: libata-core: fix when to fetch sense data for successful commands")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
commit 1e641060c4 ("libata: clear eh_info on reset completion") added
a workaround that broke the retry mechanism in ATA EH.
Tejun himself suggested to remove this workaround when it was identified
to cause additional problems:
https://lore.kernel.org/linux-ide/20110426135027.GI878@htj.dyndns.org/
He even said:
"Hmm... it seems I wasn't thinking straight when I added that work around."
https://lore.kernel.org/linux-ide/20110426155229.GM878@htj.dyndns.org/
While removing the workaround solved the issue, however, the workaround was
kept to avoid "spurious hotplug events during reset", and instead another
workaround was added on top of the existing workaround in commit
8c56cacc72 ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Because these IRQs happened when the port was frozen, we know that they
were actually a side effect of PxIS and IS.IPS(x) not being cleared before
the COMRESET. This is now done in commit 94152042eaa9 ("ata: libahci: clear
pending interrupt status"), so these workarounds can now be removed.
Since commit 1e641060c4 ("libata: clear eh_info on reset completion") has
now been reverted, the ATA EH retry mechanism is functional again, so there
is once again no need to thaw the port more than once in ata_eh_reset().
This reverts "the workaround on top of the workaround" introduced in commit
8c56cacc72 ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING,
before calling ap->ops->error_handler() (without holding the ap->lock).
If an error IRQ is received while ap->ops->error_handler() is running,
the irq handler will set ATA_PFLAG_EH_PENDING.
Once ap->ops->error_handler() returns, ata_scsi_port_error_handler()
checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration
of ATA EH is performed.
The problem is that ATA_PFLAG_EH_PENDING is not only cleared by
ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset().
ata_eh_reset() is called by ap->ops->error_handler(). This additional
clearing done by ata_eh_reset() breaks the whole retry logic in
ata_scsi_port_error_handler(). Thus, if an error IRQ is received while
ap->ops->error_handler() is running, the port will currently remain
frozen and will never get re-enabled.
The additional clearing in ata_eh_reset() was introduced in commit
1e641060c4 ("libata: clear eh_info on reset completion").
Looking at the original error report:
https://marc.info/?l=linux-ide&m=124765325828495&w=2
We can see the following happening:
[ 1.074659] ata3: XXX port freeze
[ 1.074700] ata3: XXX hardresetting link, stopping engine
[ 1.074746] ata3: XXX flipping SControl
[ 1.411471] ata3: XXX irq_stat=400040 CONN|PHY
[ 1.411475] ata3: XXX port freeze
[ 1.420049] ata3: XXX starting engine
[ 1.420096] ata3: XXX rc=0, class=1
[ 1.420142] ata3: XXX clearing IRQs for thawing
[ 1.420188] ata3: XXX port thawed
[ 1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
We are not supposed to be able to receive an error IRQ while the port is
frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled).
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states:
"Each bit location can be thought of as reporting a '1' if the virtual
"interrupt line" for that port is indicating it wishes to generate an
interrupt. That is, if a port has one or more interrupt status bit set,
and the enables for those status bits are set, then this bit shall be set."
Additionally, AHCI state P:ComInit clearly shows that the state machine
will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE
is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set.
So IS.IPS(x) only gets set if PxIS and PxIE is set.
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states:
"The bits in this register are read/write clear. It is set by the level of
the virtual interrupt line being a set, and cleared by a write of '1' from
the software."
So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to
IS.IPS(x) for that port.
Since PxIE is cleared, the only way to get an interrupt while the port is
frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when
the port is frozen, is if it was set before the port was frozen.
However, since commit 737dd811a3 ("ata: libahci: clear pending interrupt
status"), we clear both PxIS and IS.IPS(x) after freezing the port, but
before the COMRESET, so the problem that commit 1e641060c4 ("libata:
clear eh_info on reset completion") fixed can no longer happen.
Thus, revert commit 1e641060c4 ("libata: clear eh_info on reset
completion"), so that the retry logic in ata_scsi_port_error_handler()
works once again. (The retry logic is still needed, since we can still
get an error IRQ _after_ the port has been thawed, but before
ata_scsi_port_error_handler() takes the ap->lock in order to check
if ATA_PFLAG_EH_PENDING is set.)
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tony Nguyen says:
====================
Introduce Intel IDPF driver
Pavan Kumar Linga says:
This patch series introduces the Intel Infrastructure Data Path Function
(IDPF) driver. It is used for both physical and virtual functions. Except
for some of the device operations the rest of the functionality is the
same for both PF and VF. IDPF uses virtchnl version2 opcodes and
structures defined in the virtchnl2 header file which helps the driver
to learn the capabilities and register offsets from the device
Control Plane (CP) instead of assuming the default values.
The format of the series follows the driver init flow to interface open.
To start with, probe gets called and kicks off the driver initialization
by spawning the 'vc_event_task' work queue which in turn calls the
'hard reset' function. As part of that, the mailbox is initialized which
is used to send/receive the virtchnl messages to/from the CP. Once that is
done, 'core init' kicks in which requests all the required global resources
from the CP and spawns the 'init_task' work queue to create the vports.
Based on the capability information received, the driver creates the said
number of vports (one or many) where each vport is associated to a netdev.
Also, each vport has its own resources such as queues, vectors etc.
From there, rest of the netdev_ops and data path are added.
IDPF implements both single queue which is traditional queueing model
as well as split queue model. In split queue model, it uses separate queue
for both completion descriptors and buffers which helps to implement
out-of-order completions. It also helps to implement asymmetric queues,
for example multiple RX completion queues can be processed by a single
RX buffer queue and multiple TX buffer queues can be processed by a
single TX completion queue. In single queue model, same queue is used
for both descriptor completions as well as buffer completions. It also
supports features such as generic checksum offload, generic receive
offload (hardware GRO) etc.
---
v7:
Patch 2:
* removed pci_[disable|enable]_pcie_error_reporting as they are dropped
from the core
Patch 4, 9:
* used 'kasprintf' instead of 'snprintf' to avoid providing explicit
character string size which also fixes "-Wformat-truncation" warnings
Patch 14:
* used 'ethtool_sprintf' instead of 'snprintf' to avoid providing explicit
character string size which also fixes "-Wformat-truncation" warning
* add string format argument to the 'ethtool_sprintf' to avoid warning on
"-Wformat-security"
v6: https://lore.kernel.org/netdev/20230825235954.894050-1-pavan.kumar.linga@intel.com/
Note: 'Acked-by' was only added to patches 1, 2, 12 and not to the other
patches because of the changes in v6
Patch 3, 4, 5, 6, 7, 8, 9, 11, 13, 14, 15:
* renamed 'reset_lock' to 'vport_ctrl_lock' to reflect the lock usage
* to avoid defensive programming, used 'vport_ctrl_lock' for the user
callbacks that access the 'vport' to prevent the hardware reset thread
from releasing the 'vport', when the user callback is in progress
* added some variables to netdev private structure to avoid vport access
if possible from ethtool and ndo callbacks
* moved 'mac_filter_list_lock' and MAC related flags to vport_config
structure and refactored mac filter flow to handle asynchronous
ndo mac filter callbacks
* stop the queues before starting the reset flow to avoid TX hangs
* removed 'sw_mutex' and 'stop_mutex' as they are not needed anymore
* added missing clear bit in 'init_task' error path
* renamed labels appropriately
Patch 8:
* replaced page_pool_put_page with page_pool_put_full_page
* for the page pool max_len, used PAGE_SIZE
Patch 10, 11, 13:
* made use of the 'netif_txq_maybe_stop', '__netif_txq_completed_wake'
helper macros
Patch 13:
* removed IDPF_HR_RESET_IN_PROG flag check in idpf_tx_singleq_start
as it is defensive
Patch 14:
* removed max descriptor check as the core does that
* removed unnecessary error messages
* removed the stats that are common between the ones reported by ethtool
and ip link
* replaced snprintf with ethtool_sprintf
* added a comment to explain the reason for the max queue check
* as the netdev queues are set on alloc, there is no need to set
them again on reset unless there is a queue change, so move the
'idpf_set_real_num_queues' to 'idpf_initiate_soft_reset'
Patch 15:
* reworded the 'configure SRIOV' in the commit message
v5: https://lore.kernel.org/netdev/20230816004305.216136-1-anthony.l.nguyen@intel.com/
Most Patches:
* wrapped line limit to 80 chars to those which don't effect readability
Patch 12:
* in skb_add_rx_frag, offset 'headlen' w.r.t page_offset when adding a
frag to avoid adding the header again
Patch 14:
* added NULL check for 'rxq' when dereferencing it in page_pool_get_stats
v4: https://lore.kernel.org/netdev/20230808003416.3805142-1-anthony.l.nguyen@intel.com/
Patch 1:
* s/virtcnl/virtchnl
* removed the kernel doc for the error code definitions that don't exist
* reworded the summary part in the virtchnl2 header
Patch 3:
* don't set local variable to NULL on error
* renamed sq_send_command_out label with err_unlock
* don't use __GFP_ZERO in dma_alloc_coherent
Patch 4:
* introduced mailbox workqueue to process mailbox interrupts
Patch 3, 4, 5, 6, 7, 8, 9, 11, 15:
* removed unnecessary variable 0-init
Patch 3, 5, 7, 8, 9, 15:
* removed defensive programming checks wherever applicable
* removed IDPF_CAP_FIELD_LAST as it can be treated as defensive
programming
Patch 3, 4, 5, 6, 7:
* replaced IDPF_DFLT_MBX_BUF_SIZE with IDPF_CTLQ_MAX_BUF_LEN
Patch 2 to 15:
* add kernel-doc for idpf.h and idpf_txrx.h enums and structures
Patch 4, 5, 15:
* adjusted the destroy sequence of the workqueues as per the alloc
sequence
Patch 4, 5, 9, 15:
* scrub unnecessary flags in 'idpf_flags'
- IDPF_REMOVE_IN_PROG flag can take care of the cases where
IDPF_REL_RES_IN_PROG is used, removed the later one
- IDPF_REQ_[TX|RX]_SPLITQ are replaced with struct variables
- IDPF_CANCEL_[SERVICE|STATS]_TASK are redundant as the work queue
doesn't get rescheduled again after 'cancel_delayed_work_sync'
- IDPF_HR_CORE_RESET is removed as there is no set_bit for this flag
- IDPF_MB_INTR_TRIGGER is removed as it is not needed anymore with the
mailbox workqueue implementation
Patch 7 to 15:
* replaced the custom buffer recycling code with page pool API
* switched the header split buffer allocations from using a bunch of
pages to using one large chunk of DMA memory
* reordered some of the flows in vport_open to support page pool
Patch 8, 12:
* don't suppress the alloc errors by using __GFP_NOWARN
Patch 9:
* removed dyn_ctl_clrpba_m as it is not being used
Patch 14:
* introduced enum idpf_vport_reset_cause instead of using vport flags
* introduced page pool stats
v3: https://lore.kernel.org/netdev/20230616231341.2885622-1-anthony.l.nguyen@intel.com/
Patch 5:
* instead of void, used 'struct virtchnl2_create_vport' type for
vport_params_recvd and vport_params_reqd and removed the typecasting
* used u16/u32 as needed instead of int for variables which cannot be
negative and updated in all the places whereever applicable
Patch 6:
* changed the commit message to "add ptypes and MAC filter support"
* used the sender Signed-off-by as the last tag on all the patches
* removed unnecessary variables 0-init
* instead of fixing the code in this commit, fixed it in the commit
where the change was introduced first
* moved get_type_info struct on to the stack instead of memory alloc
* moved mutex_lock and ptype_info memory alloc outside while loop and
adjusted the return flow
* used 'break' instead of 'continue' in ptype id switch case
v2: https://lore.kernel.org/netdev/20230614171428.1504179-1-anthony.l.nguyen@intel.com/
Patch 2:
* added "Intel(R)" to the DRV_SUMMARY and Makefile.
Patch 4, 5, 6, 15:
* replaced IDPF_VC_MSG_PENDING flag with mutex 'vc_buf_lock' for the
adapter related virtchnl opcodes.
* get the mutex lock in the virtchnl send thread itself instead of
in receive thread.
Patch 5, 6, 7, 8, 9, 11, 14, 15:
* replaced IDPF_VPORT_VC_MSG_PENDING flag with mutex 'vc_buf_lock' for
the vport related virtchnl opcodes.
* get the mutex lock in the virtchnl send thread itself instead of
in receive thread.
Patch 6:
* converted get_ptype_info logic from 1:N to 1:1 message exchange for
better handling of mutex lock.
Patch 15:
* introduced 'stats_lock' spinlock to avoid concurrent stats update.
v1: https://lore.kernel.org/netdev/20230530234501.2680230-1-anthony.l.nguyen@intel.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Keguang Zhang says:
====================
Move Loongson1 MAC arch-code to the driver dir
In order to convert Loongson1 MAC platform devices to the devicetree
nodes, Loongson1 MAC arch-code should be moved to the driver dir.
Add dt-binding document and update MAINTAINERS file accordingly.
In other words, this patchset is a preparation for converting
Loongson1 platform devices to devicetree.
Changelog
V4 -> V5: Replace stmmac_probe_config_dt() with devm_stmmac_probe_config_dt()
Replace stmmac_pltfr_probe() with devm_stmmac_pltfr_probe()
Squash patch 4 into patch 2 and 3
V3 -> V4: Add Acked-by tag from Krzysztof Kozlowski
Add "|" to description part
Amend "phy-mode" property
Drop ls1x_dwmac_syscon definition and its instances
Drop three redundant fields from the ls1x_dwmac structure
Drop the ls1x_dwmac_init() method.
Update the dt-binding document entry of Loongson1 Ethernet
Some minor improvements
V2 -> V3: Split the DT-schema file into loongson,ls1b-gmac.yaml
and loongson,ls1c-emac.yaml (suggested by Serge Semin)
Change the compatibles to loongson,ls1b-gmac and loongson,ls1c-emac
Rename loongson,dwmac-syscon to loongson,ls1-syscon
Amend the title
Add description
Add Reviewed-by tag from Krzysztof Kozlowski
Change compatibles back to loongson,ls1b-syscon
and loongson,ls1c-syscon
Determine the device ID by physical
base address(suggested by Serge Semin)
Use regmap instead of regmap fields
Use syscon_regmap_lookup_by_phandle()
Some minor fixes
Update the entries of MAINTAINERS
V1 -> V2: Leave the Ethernet platform data for now
Make the syscon compatibles more specific
Fix "clock-names" and "interrupt-names" property
Rename the syscon property to "loongson,dwmac-syscon"
Drop "phy-handle" and "phy-mode" requirement
Revert adding loongson,ls1b-dwmac/loongson,ls1c-dwmac
to snps,dwmac.yaml
Fix the build errors due to CONFIG_OF being unset
Change struct reg_field definitions to const
Rename the syscon property to "loongson,dwmac-syscon"
Add MII PHY mode for LS1C
Improve the commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This glue driver is created based on the arch-code
implemented earlier with the platform-specific settings.
Use syscon for SYSCON register access.
And modify MAINTAINERS to add a new F: entry for this driver.
Partially based on the previous work by Serge Semin.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devicetree binding document for Loongson-1 Ethernet controller.
And modify MAINTAINERS to add a new F: entry for
Loongson1 dt-binding documents.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Loongson LS1B and LS1C compatibles for system controller.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ionic device supports a maximum buffer length of 16 bits (see
ionic_rxq_desc or ionic_rxq_sg_elem). When adding new buffers to
the receive rings, the function ionic_rx_fill() uses 16bit math when
calculating the number of pages to allocate for an RX descriptor,
given the interface's MTU setting. If the system PAGE_SIZE >= 64KB,
and the buf_info->page_offset is 0, the remain_len value will never
decrement from the original MTU value and the frag_len value will
always be 0, causing additional pages to be allocated as scatter-
gather elements unnecessarily.
A similar math issue exists in ionic_rx_frags(), but no failures
have been observed here since a 64KB page should not normally
require any scatter-gather elements at any legal Ethernet MTU size.
Fixes: 4b0a7539a3 ("ionic: implement Rx page reuse")
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the style used in the core kernel (e.g.
include/linux/etherdevice.h and include/linux/in6.h) for the PTP IPv6
and Ethernet addresses. No functional changes.
Signed-off-by: Alex Austin <alex.austin@amd.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if wlan.offload_enable and wlan.offload_disable callbacks are set
in mtk_wed_flow_add/mtk_wed_flow_remove since mt7996 will not rely
on them.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 21 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 450 insertions(+), 36 deletions(-).
The main changes are:
1) Adjust bpf_mem_alloc buckets to match ksize(), from Hou Tao.
2) Check whether override is allowed in kprobe mult, from Jiri Olsa.
3) Fix btf_id symbol generation with ld.lld, from Jiri and Nick.
4) Fix potential deadlock when using queue and stack maps from NMI, from Toke Høiland-Jørgensen.
Please consider pulling these changes from:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf.git
Thanks a lot!
Also thanks to reporters, reviewers and testers of commits in this pull-request:
Alan Maguire, Biju Das, Björn Töpel, Dan Carpenter, Daniel Borkmann,
Eduard Zingerman, Hsin-Wei Hung, Marcus Seyfarth, Nathan Chancellor,
Satya Durga Srinivasu Prabhala, Song Liu, Stephen Rothwell
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be time consuming to track driver bugs, that might be detected
too late from this confusing warning in skb_try_coalesce()
WARN_ON_ONCE(delta < len);
Add sanity check in skb_add_rx_frag() and skb_coalesce_rx_frag()
to better track bug origin for CONFIG_DEBUG_NET=y builds.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding sk->sk_prot->release_cb() call from __sk_flush_backlog()
Paolo suggested using indirect call helpers to take care of
CONFIG_RETPOLINE=y case.
It turns out Google had such mitigation for years in release_sock(),
it is time to make this public :)
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existence of struct cxl_dev_id containing a single member is odd.
The comment made sense when I wrote it but could be clarified.
Update the comment and place it next to the odd looking structure.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20230426-cxl-fixes-v1-2-870c4c8b463a@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The cxl_test platform device CXL port hierarchy is useful for testing,
but throws warning messages of the form:
cxl_mem mem2: at cxl_root_port.1 no parent for dport: platform
cxl_mem mem3: at cxl_root_port.2 no parent for dport: platform
cxl_mem mem4: at cxl_root_port.3 no parent for dport: platform
cxl_mem mem5: at cxl_root_port.0 no parent for dport: platform
cxl_mem mem6: at cxl_root_port.1 no parent for dport: platform
cxl_mem mem7: at cxl_root_port.2 no parent for dport: platform
cxl_mem mem8: at cxl_root_port.3 no parent for dport: platform
cxl_mem mem9: at cxl_root_port.4 no parent for dport: platform
cxl_mem mem10: at cxl_root_port.4 no parent for dport: platform
...and this message when running testing in QEMU:
cxl_region region4: Bypassing cpu_cache_invalidate_memregion() for testing!
Noisy cxl_test warnings have caused other regressions to be missed. In
the interest of using cxl_test for early detection of dev_err() and
dev_warn() messages, silence platform device topology and
cache-invalidation messages.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This kselftest fixes update for Linux 6.6-rc2 consists of important
fixes to user_events test and ftrace test.
user_events test has been enabled for default run in Linux 6.6-rc1. The
following fixes are for bugs found since then:
- adds checks for dependencies and skips the test. user_events test
requires root access, and tracefs and user_events enabled. It leaves
tracefs mounted and a fix is in progress for that missing piece.
- creates user_events test-specific Kconfig fragments.
ftrace test fixes:
- unmounts tracefs for recovering environment. Fix identified during the
above mentioned user_events dependencies fix.
- adds softlink to latest log directory improving usage.
-----BEGIN PGP SIGNATURE-----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=HdKU
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull more kselftest fixes from Shuah Khan
"Fixes to user_events test and ftrace test.
The user_events test was enabled by default in Linux 6.6-rc1. The
following fixes are for bugs found since then:
- add checks for dependencies and skip the test if they aren't met.
The user_events test requires root access, and tracefs and
user_events enabled. It leaves tracefs mounted and a fix is in
progress for that missing piece.
- create user_events test-specific Kconfig fragments
ftrace test fixes:
- unmount tracefs for recovering environment. Fix identified during
the above mentioned user_events dependencies fix.
- adds softlink to latest log directory improving usage"
* tag 'linux-kselftest-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: tracing: Fix to unmount tracefs for recovering environment
selftests: user_events: create test-specific Kconfig fragments
ftrace/selftests: Add softlink to latest log directory
selftests/user_events: Fix failures when user_events is not installed
The BPF JITs now support cpuv4 instructions. Add tests for these new
instructions to the test suite:
1. Sign extended Load
2. Sign extended Mov
3. Unconditional byte swap
4. Unconditional jump with 32-bit offset
5. Signed division and modulo
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20230907230550.1417590-9-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ARM32 doesn't have instructions to do 64-bit/64-bit divisions. So, to
implement the following instructions:
BPF_ALU64 | BPF_DIV
BPF_ALU64 | BPF_MOD
BPF_ALU64 | BPF_SDIV
BPF_ALU64 | BPF_SMOD
We implement the above instructions by doing function calls to div64_u64()
and div64_u64_rem() for unsigned division/mod and calls to div64_s64()
for signed division/mod.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-7-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The cpuv4 added a new BPF_SDIV instruction that does signed division.
The encoding is similar to BPF_DIV but BPF_SDIV sets offset=1.
ARM32 already supports 32-bit BPF_DIV which can be easily extended to
support BPF_SDIV as ARM32 has the SDIV instruction. When the CPU is not
ARM-v7, we implement that SDIV/SMOD with the function call similar to
the implementation of DIV/MOD.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-6-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The cpuv4 added a new unconditional bswap instruction with following
behaviour:
BPF_ALU64 | BPF_TO_LE | BPF_END with imm = 16/32/64 means:
dst = bswap16(dst)
dst = bswap32(dst)
dst = bswap64(dst)
As we already support converting to big-endian from little-endian we can
use the same for unconditional bswap. just treat the unconditional scenario
the same as big-endian conversion.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-5-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The cpuv4 added a new BPF_MOVSX instruction that sign extends the src
before moving it to the destination.
BPF_ALU | BPF_MOVSX sign extends 8-bit and 16-bit operands into 32-bit
operands, and zeroes the remaining upper 32 bits.
BPF_ALU64 | BPF_MOVSX sign extends 8-bit, 16-bit, and 32-bit operands
into 64-bit operands.
The offset field of the instruction is used to tell the number of bit to
use for sign-extension. BPF_MOV and BPF_MOVSX have the same code but the
former sets offset to 0 and the later one sets the offset to 8, 16 or 32
The behaviour of this instruction is dst = (s8,s16,s32)src
On ARM32 the implementation uses LSH and ARSH to extend the 8/16 bits to
a 32-bit register and then it is sign extended to the upper 32-bit
register using ARSH. For 32-bit we just move it to the destination
register and use ARSH to extend it to the upper 32-bit register.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-4-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The cpuv4 added the support of an instruction that is similar to load
but also sign-extends the result after the load.
BPF_MEMSX | <size> | BPF_LDX means dst = *(signed size *) (src + offset)
here <size> can be one of BPF_B, BPF_H, BPF_W.
ARM32 has instructions to load a byte or a half word with sign
extension into a 32bit register. As the JIT uses two 32 bit registers
to simulate a 64-bit BPF register, an extra instruction is emitted to
sign-extent the result up to the second register.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-3-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The cpuv4 adds unconditional jump with 32-bit offset where the immediate
field of the instruction is to be used to calculate the jump offset.
BPF_JA | BPF_K | BPF_JMP32 => gotol +imm => PC += imm.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230907230550.1417590-2-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- Use correct order when encoding NFSv4 RENAME change_info
- Fix a potential oops during NFSD shutdown
-----BEGIN PGP SIGNATURE-----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=ZTRy
-----END PGP SIGNATURE-----
Merge tag 'nfsd-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Use correct order when encoding NFSv4 RENAME change_info
- Fix a potential oops during NFSD shutdown
* tag 'nfsd-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: fix possible oops when nfsd/pool_stats is closed.
nfsd: fix change_info in NFSv4 RENAME replies
Instructions with sign- and zero- extention like movsbl and movzwq were
not handled properly. As it can check different size suffix (-b, -w, -l
or -q) we can omit that and add the common parts even though some
combinations are not possible.
Reviewed-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20230908052216.566148-1-namhyung@kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
pmu_events_table__find() is no longer used so remove it and its Arm
specific version.
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Eduard Zingerman <eddyz87@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Jing Zhang <renyu.zj@linux.alibaba.com>
Cc: Haixin Yu <yuhaixin.yhx@linux.alibaba.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20230913153355.138331-4-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Currently the while loop always either exits on the first iteration with
a core PMU, or exits with NULL on heterogeneous systems or when not all
CPUs are online.
Both of the latter behaviors are undesirable for platforms other than
Arm so simplify it to always return the first core PMU, or NULL if none
exist.
This behavior was depended on by the Arm version of
pmu_metrics_table__find(), so the logic has been moved there instead.
Signed-off-by: James Clark <james.clark@arm.com>
Suggested-by: Ian Rogers <irogers@google.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Eduard Zingerman <eddyz87@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Jing Zhang <renyu.zj@linux.alibaba.com>
Cc: Haixin Yu <yuhaixin.yhx@linux.alibaba.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20230913153355.138331-3-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
pmu__find_core_pmu() more logically belongs in pmus.c because it
iterates over all PMUs, so move it to pmus.c
At the same time rename it to perf_pmus__find_core_pmu() to match the
naming convention in this file.
list_prepare_entry() can't be used in perf_pmus__scan_core() anymore now
that it's called from the same compilation unit. This is with -O2
(specifically -O1 -ftree-vrp -finline-functions
-finline-small-functions) which allow the bounds of the array
access to be determined at compile time. list_prepare_entry() subtracts
the offset of the 'list' member in struct perf_pmu from &core_pmus,
which isn't a struct perf_pmu. The compiler sees that pmu results in
&core_pmus - 8 and refuses to compile. At runtime this works because
list_for_each_entry_continue() always adds the offset back again before
dereferencing ->next, but it's technically undefined behavior. With
-fsanitize=undefined an additional warning is generated.
Using list_first_entry_or_null() to get the first entry here avoids
doing &core_pmus - 8 but has the same result and fixes both the compile
warning and the undefined behavior warning. There are other uses of
list_prepare_entry() in pmus.c, but the compiler doesn't seem to be
able to see that they can also be called with &core_pmus, so I won't
change any at this time.
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Eduard Zingerman <eddyz87@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Jing Zhang <renyu.zj@linux.alibaba.com>
Cc: Haixin Yu <yuhaixin.yhx@linux.alibaba.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20230913153355.138331-2-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The node (nd) may be NULL and pointer arithmetic on NULL is undefined
behavior. Move the computation of next below the NULL check on the
node.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20230914044233.1550195-1-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Don't populate the const array controls on the stack, instead make it
static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230915092639.31074-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the handling of block devices in the test_resume mode of
hibernation (Chen Yu).
-----BEGIN PGP SIGNATURE-----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=3TcT
-----END PGP SIGNATURE-----
Merge tag 'pm-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix the handling of block devices in the test_resume mode of
hibernation (Chen Yu)"
* tag 'pm-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix the exclusive get block device in test_resume mode
PM: hibernate: Rename function parameter from snapshot_test to exclusive
- Unbreak disabled trip point check in handle_thermal_trip() that may
cause it to skip enabled trip points (Rafael Wysocki).
- Add missing of_node_put() to of_find_trip_id() and
thermal_of_for_each_cooling_maps() that each break out of a
for_each_child_of_node() loop without dropping the reference to
the child object (Julia Lawall).
- Constify the recently added trip argument of the .get_trend() thermal
zone callback (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----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=D9SO
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix a thermal core breakage introduced by one of the recent
changes, amend those changes by adding 'const' to a new callback
argument and fix two memory leaks.
Specifics:
- Unbreak disabled trip point check in handle_thermal_trip() that may
cause it to skip enabled trip points (Rafael Wysocki)
- Add missing of_node_put() to of_find_trip_id() and
thermal_of_for_each_cooling_maps() that each break out of a
for_each_child_of_node() loop without dropping the reference to the
child object (Julia Lawall)
- Constify the recently added trip argument of the .get_trend()
thermal zone callback (Rafael Wysocki)"
* tag 'thermal-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Fix disabled trip point check in handle_thermal_trip()
thermal: Constify the trip argument of the .get_trend() zone callback
thermal/of: add missing of_node_put()
table's list of devices that is managed using dm_{get,put}_device.
- Revert DM core's half-baked RCU optimization if IO submitter has set
REQ_NOWAIT. Can be revisited, and properly justified, after
comprehensively auditing all of DM to also pass GFP_NOWAIT for any
allocations if REQ_NOWAIT used.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAmUEt7wACgkQxSPxCi2d
A1prNwf/RB4EyKiSx7XS3ysM6mh/BPGO5FNjWwHebkrSFzAkEowo4i0cY9lRD0N4
x9Wbd5bcV8HarH/fiyffQxgdfXspAIrMt8z5hRnfElkBLzg6hHixxg/3sFCwg+U3
LG6AZFNLil7VmDeca9Pd8MCyXoy1u4ErWjkz3fU8pzzT+NDwRZPZhUMd/MFCWag6
q22S8KMXkYKiAHqKauF52CeDH77XsO66G70t/AElemZ66PpyKpasg2p99RCuHgTg
7jNuMTM6qXYWSWw8OswVXCPZEVfCp4zTFv1ebu9bagfDKR4ppNxwzyz7/CMkir14
4uKKzQ/cy8QND6OR/05zKh4U3ctqyA==
=rVpu
-----END PGP SIGNATURE-----
Merge tag 'for-6.6/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM core retrieve_deps() UAF race due to missing locking of a DM
table's list of devices that is managed using dm_{get,put}_device.
- Revert DM core's half-baked RCU optimization if IO submitter has set
REQ_NOWAIT. Can be revisited, and properly justified, after
comprehensively auditing all of DM to also pass GFP_NOWAIT for any
allocations if REQ_NOWAIT used.
* tag 'for-6.6/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: don't attempt to queue IO under RCU protection
dm: fix a race condition in retrieve_deps
-----BEGIN PGP SIGNATURE-----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=uNVj
-----END PGP SIGNATURE-----
Merge tag 'block-6.6-2023-09-15' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull via Keith:
- nvme-tcp iov len fix (Varun)
- nvme-hwmon const qualifier for safety (Krzysztof)
- nvme-fc null pointer checks (Nigel)
- nvme-pci no numa node fix (Pratyush)
- nvme timeout fix for non-compliant controllers (Keith)
- MD pull via Song fixing regressions with both 6.5 and 6.6
- Fix a use-after-free regression in resizing blk-mq tags (Chengming)
* tag 'block-6.6-2023-09-15' of git://git.kernel.dk/linux:
nvme: avoid bogus CRTO values
md: Put the right device in md_seq_next
nvme-pci: do not set the NUMA node of device if it has none
blk-mq: fix tags UAF when shrinking q->nr_hw_queues
md/raid1: fix error: ISO C90 forbids mixed declarations
md: fix warning for holder mismatch from export_rdev()
md: don't dereference mddev after export_rdev()
nvme-fc: Prevent null pointer dereference in nvme_fc_io_getuuid()
nvme: host: hwmon: constify pointers to hwmon_channel_info
nvmet-tcp: pass iov_len instead of sg->length to bvec_set_page()
-----BEGIN PGP SIGNATURE-----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=0Mv3
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.6-2023-09-15' of git://git.kernel.dk/linux
Pull io_uring fix from Jens Axboe:
"Just a single fix, fixing a regression with poll first, recvmsg, and
using a provided buffer"
* tag 'io_uring-6.6-2023-09-15' of git://git.kernel.dk/linux:
io_uring/net: fix iter retargeting for selected buf
A change applied to v6.5 kernel brings an issue that usual GFP allocation
is done in atomic context under acquired spin-lock. Let us revert it.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQE66IEYNDXNBPeGKSsLtaWM8LwEwUCZQQq3QAKCRCsLtaWM8Lw
ExNAAP9q3ke8sQnVB0/xp2ggfPEmf/krJ685EcDTLX412MR9oAEA7WqFrbZVJrVm
+/eL4H38iFH1utrfG/zFj7LAonPVdAQ=
=+maU
-----END PGP SIGNATURE-----
Merge tag 'firewire-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Takashi Sakamoto:
"A change applied to v6.5 kernel brings an issue that usual GFP
allocation is done in atomic context under acquired spin-lock. Let us
revert it"
* tag 'firewire-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
Revert "firewire: core: obsolete usage of GFP_ATOMIC at building node tree"
