Extend the SCP binding to describe the MT8195 dual-core SCP.
Under different applications, the MT8195 SCP can be used as single-core
or dual-core. This change keeps the single-core definitions and
adds new definitions for the dual-core use case.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230901080935.14571-4-tinghan.shen@mediatek.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
We have been consistently seeing hangs with generic/648 in our subpage
GitHub CI setup. This is a classic deadlock, we are calling
btrfs_read_folio() on a folio, which requires holding the folio lock on
the folio, and then finding a ordered extent that overlaps that range
and calling btrfs_start_ordered_extent(), which then tries to write out
the dirty page, which requires taking the folio lock and then we
deadlock.
The hang happens because we're writing to range [1271750656, 1271767040),
page index [77621, 77622], and page 77621 is !Uptodate. It is also Dirty,
so we call btrfs_read_folio() for 77621 and which does
btrfs_lock_and_flush_ordered_range() for that range, and we find an ordered
extent which is [1271644160, 1271746560), page index [77615, 77621].
The page indexes overlap, but the actual bytes don't overlap. We're
holding the page lock for 77621, then call
btrfs_lock_and_flush_ordered_range() which tries to flush the dirty
page, and tries to lock 77621 again and then we deadlock.
The byte ranges do not overlap, but with subpage support if we clear
uptodate on any portion of the page we mark the entire thing as not
uptodate.
We have been clearing page uptodate on write errors, but no other file
system does this, and is in fact incorrect. This doesn't hurt us in the
!subpage case because we can't end up with overlapped ranges that don't
also overlap on the page.
Fix this by not clearing uptodate when we have a write error. The only
thing we should be doing in this case is setting the mapping error and
carrying on. This makes it so we would no longer call
btrfs_read_folio() on the page as it's uptodate and eliminates the
deadlock.
With this patch we're now able to make it through a full fstests run on
our subpage blocksize VMs.
Note for stable backports: this probably goes beyond 6.1 but the code
has been cleaned up and clearing the uptodate bit must be verified on
each version independently.
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This was noticed by Miklos that file_remove_privs might call into
notify_change(), which requires to hold an exclusive lock. The problem
exists in FUSE and btrfs. We can fix it without any additional helpers
from VFS, in case the privileges would need to be dropped, change the
lock type to be exclusive and redo the loop.
Fixes: e9adabb971 ("btrfs: use shared lock for direct writes within EOF")
CC: Miklos Szeredi <miklos@szeredi.hu>
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Remove a number of hidden calls to compound_head() by using a folio
throughout. Also follow core kernel coding style by adding the folio to
the page cache immediately after allocation instead of doing the read
first, then adding it to the page cache. This ordering makes subsequent
readers block waiting for the first reader instead of duplicating the
work only to throw it away when they find out they lost the race.
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Improve the definition of the rpmsg subnode by assigning a distinct
node name and adding the definition source of node properties.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230901080935.14571-2-tinghan.shen@mediatek.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant. Removing outside dev_err_probe() to
clean it up.
Besides, switch to use platform_get_irq_optional() since the irq
is optional here.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20230817083336.404635-1-chenjiahao16@huawei.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Previously CRC stripping was always enabled for VF.
Now it is possible to turn off CRC stripping via ethtool:
#ethtool -K <interface> rx-fcs on
To turn off CRC stripping, first VLAN stripping must be disabled:
#ethtool -K <interface> rx-vlan-offload off
if any VLAN interfaces exists, otherwise VLAN stripping will be turned
off by the driver.
In iavf_configure_queues add check if CRC stripping is enabled for
VF, if it's enabled then set crc_disabled to false on every VF's
queue. In iavf_set_features add check if CRC stripping setting was
changed then schedule reset.
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When VLAN strip is enabled, the CRC strip must not be disabled. And when
the CRC strip is disabled, the VLAN strip should not be enabled.
The driver needs to check CRC strip disable setting parameter before
configuring the Rx/Tx queues, otherwise, in current error handling,
the already set Tx queue context doesn't roll back correctly, it will
cause the Tx queue setup failure next time:
"Failed to set LAN Tx queue context"
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To support CRC strip enable/disable functionality, VF needs the explicit
request VIRTCHNL_VF_OFFLOAD_CRC offload. Then according to crc_disable
flag of Rx queue configuration information to set up the queue context.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when GETDEVICEINFO returns multiple locations where each
is a different IP but the server's identity is same as MDS, then
nfs4_set_ds_client() finds the existing nfs_client structure which
has the MDS's max_connect value (and if it's 1), then the 1st IP
on the DS's list will get dropped due to MDS trunking rules. Other
IPs would be added as they fall under the pnfs trunking rules.
For the list of IPs the 1st goes thru calling nfs4_set_ds_client()
which will eventually call nfs4_add_trunk() and call into
rpc_clnt_test_and_add_xprt() which has the check for MDS trunking.
The other IPs (after the 1st one), would call rpc_clnt_add_xprt()
which doesn't go thru that check.
nfs4_add_trunk() is called when MDS trunking is happening and it
needs to enforce the usage of max_connect mount option of the
1st mount. However, this shouldn't be applied to pnfs flow.
Instead, this patch proposed to treat MDS=DS as DS trunking and
make sure that MDS's max_connect limit does not apply to the
1st IP returned in the GETDEVICEINFO list. It does so by
marking the newly created client with a new flag NFS_CS_PNFS
which then used to pass max_connect value to use into the
rpc_clnt_test_and_add_xprt() instead of the existing rpc
client's max_connect value set by the MDS connection.
For example, mount was done without max_connect value set
so MDS's rpc client has cl_max_connect=1. Upon calling into
rpc_clnt_test_and_add_xprt() and using rpc client's value,
the caller passes in max_connect value which is previously
been set in the pnfs path (as a part of handling
GETDEVICEINFO list of IPs) in nfs4_set_ds_client().
However, when NFS_CS_PNFS flag is not set and we know we
are doing MDS trunking, comparing a new IP of the same
server, we then set the max_connect value to the
existing MDS's value and pass that into
rpc_clnt_test_and_add_xprt().
Fixes: dc48e0abee ("SUNRPC enforce creation of no more than max_connect xprts")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This reverts commit 0701214cd6.
The premise of this commit was incorrect. There are exactly 2 cases
where rpcauth_checkverf() will return an error:
1) If there was an XDR decode problem (i.e. garbage data).
2) If gss_validate() had a problem verifying the RPCSEC_GSS MIC.
In the second case, there are again 2 subcases:
a) The GSS context expires, in which case gss_validate() will force a
new context negotiation on retry by invalidating the cred.
b) The sequence number check failed because an RPC call timed out, and
the client retransmitted the request using a new sequence number,
as required by RFC2203.
In neither subcase is this a fatal error.
Reported-by: Russell Cattelan <cattelan@thebarn.com>
Fixes: 0701214cd6 ("SUNRPC: Fail faster on bad verifier")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the server rejects the credential as being stale, or bad, then we
should mark it for revalidation before retransmitting.
Fixes: 7f5667a5f8 ("SUNRPC: Clean up rpc_verify_header()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
With IPv6, connect() can occasionally return EINVAL if a route is
unavailable. If this happens during I/O to a data server, we want to
report it using LAYOUTERROR as an inability to connect.
Fixes: dd52128afd ("NFSv4.1/pnfs Ensure flexfiles reports all connection related errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Ensure that all requests are put back onto the commit list so that they
can be rescheduled.
Fixes: 4daaeba938 ("NFS: Fix nfs_direct_write_reschedule_io()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Ensure that nfs_clear_request_commit() updates the correct counters when
it removes them from the commit list.
Fixes: ed5d588fe4 ("NFS: Try to join page groups before an O_DIRECT retransmission")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If we hit a fatal error when retransmitting, we do need to record the
removal of the request from the count of written bytes.
Fixes: 031d73ed76 ("NFS: Fix O_DIRECT accounting of number of bytes read/written")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The dreq fields are protected by the dreq->lock.
Fixes: 954998b60c ("NFS: Fix error handling for O_DIRECT write scheduling")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Some VFs may want to disable CRC stripping on incoming packets so create
an offload for that. The VF already sends information about configuring
its RX queues so use that structure to indicate that the CRC stripping
should be enabled or not.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about this fix:
- When adding drm_atomic_helper_shutdown() to the unbind path, I added
it after drm_kms_helper_poll_fini() since that's when other drivers
seemed to have it.
- Technically with a previous patch, ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop"), we don't
actually need to check to see if our "drm" pointer is NULL before
calling drm_atomic_helper_shutdown(). We'll leave the "if" test in,
though, so that this patch can land without any dependencies. It
could potentially be removed later.
- This patch also makes sure to set the drvdata to NULL in the case of
bind errors to make sure that shutdown can't access freed data.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901164111.RFT.13.I0a9940ff6f387d6acf4e71d8c7dbaff8c42e3aaa@changeid
As with other places in the Linux kernel--kfree(NULL) being the most
famous example--it's convenient to treat being passed a NULL argument
as a noop in cleanup functions. Let's make
drm_atomic_helper_shutdown() work like this.
This is convenient for DRM devices that use the "component" model. On
these devices we want shutdown to be a noop if the bind() call of the
component hasn't been called yet. As long as drivers are careful to
make sure the drvdata is NULL whenever the driver is not bound then we
can just do a simple call to drm_atomic_helper_shutdown() with the
drvdata at shutdown time.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.1.I906acd535bece03b6671d97c2826c6f0444f4728@changeid
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
For the "otm8009a" driver we fully remove the storing of the "enabled"
state and we remove the double-checking, but we still keep the storing
of the "prepared" state since the backlight code in the driver checks
it. This backlight code may not be perfectly safe since there doesn't
appear to be sufficient synchronization between the backlight driver
(which userspace can call into directly) and the code that's
unpreparing the panel. However, this lack of safety is not new and can
be addressed in a future patch.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.3.I6a4a3c81c78acf5acdc2e5b5d936e19bf57ec07a@changeid
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
For the s6e63m0 panel driver, this actually fixes a subtle/minor error
handling bug in s6e63m0_prepare(). In one error case s6e63m0_prepare()
called s6e63m0_unprepare() directly if there was an error. This call
to s6e63m0_unprepare() would have been a no-op since ctx->prepared
wasn't set yet.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.2.Iabafd062e70f6b6b554cf23eeb75f57a80f7e985@changeid
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
This pile of panel drivers appears to be simple to handle. Based on
code inspection they seemed to be using the prepared/enabled state
simply for double-checking that nothing else in the kernel called them
inconsistently. Now that the core drm_panel is doing the double
checking (and warning) it should be very clear that these devices
don't need their own double-check.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.1.Ia54954fd2f7645c1b86597494902973f57feeb71@changeid
The patch e2b76ab8b5: "ksmbd: add support for read compound" leads
to the following Smatch static checker warning:
fs/smb/server/smb2pdu.c:6329 smb2_read()
warn: passing freed memory 'aux_payload_buf'
It doesn't matter that we're passing a freed variable because nbytes is
zero. This patch set "aux_payload_buf = NULL" to make smatch silence.
Fixes: e2b76ab8b5 ("ksmbd: add support for read compound")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
mark_inode_dirty will be called in notify_change().
This patch remove unneeded mark_inode_dirty in set_info_sec().
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.
If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:
1) After cs42l42_sdw_probe() returns the thread that called it
will call cs42l42_sdw_update_status() to report the last
status recorded by the SoundWire core.
2) The SoundWire bus master will see a PING with the CS42L42
now reporting as unenumerated and will trigger the core
SoundWire code to start enumerating CS42L42.
These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.
To avoid this race condition:
- Leave RESET asserted on exit from cs42l42_sdw_probe().
This ensures that an UNATTACHED notification must be
sent to the cs42l42 driver. If cs42l42 was already
enumerated it will be seen to drop off the bus, causing
an UNATTACH notification. If it was never enumerated the
status is already UNATTACHED and this will be reported
by thread (1).
- When the UNATTACH notification is received, release RESET.
This will cause CS42L42 to be enumerated and eventually
report an ATTACHED notification.
- The ATTACHED notification is now valid.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.
Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L42 can accept very short reset pulses of a few microseconds
but there's no reason to force a very short pulse.
Allow a wide range for the usleep_range() so it can be relaxed about
the choice of timing source.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Track DP enhanced framing properly in the crtc state instead
of relying just on the cached DPCD everywhere, and hook it
up into the state check and dump.
v2: Actually set enhanced_framing in .compute_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503113659.16305-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
We can get a UBSAN warning if ieee80211_get_tx_power() returns the
INT_MIN value mac80211 internally uses for "unset power level".
UBSAN: signed-integer-overflow in net/wireless/nl80211.c:3816:5
-2147483648 * 100 cannot be represented in type 'int'
CPU: 0 PID: 20433 Comm: insmod Tainted: G WC OE
Call Trace:
dump_stack+0x74/0x92
ubsan_epilogue+0x9/0x50
handle_overflow+0x8d/0xd0
__ubsan_handle_mul_overflow+0xe/0x10
nl80211_send_iface+0x688/0x6b0 [cfg80211]
[...]
cfg80211_register_wdev+0x78/0xb0 [cfg80211]
cfg80211_netdev_notifier_call+0x200/0x620 [cfg80211]
[...]
ieee80211_if_add+0x60e/0x8f0 [mac80211]
ieee80211_register_hw+0xda5/0x1170 [mac80211]
In this case, simply return an error instead, to indicate
that no data is available.
Cc: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20230203023636.4418-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver doesn't fill NL80211_STA_INFO_TX_BITRATE in sta_set_sinfo()
then as a fallback sta->deflink.tx_stats.last_rate is used. Unfortunately
there's no guarantee that this has actually been set before it's used.
Originally found when 'iw <dev> link' would always return a tx rate of
6Mbps regardless of actual link speed for the QCA9337 running firmware
WLAN.TF.2.1-00021-QCARMSWP-1 in my netbook.
Use the sanity check logic from ieee80211_fill_rx_status() and refactor
that to use the new inline function.
Signed-off-by: Stephen Douthit <stephen.douthit@gmail.com>
Link: https://lore.kernel.org/r/20230213204024.3377-1-stephen.douthit@gmail.com
[change to bool ..._rate_valid() instead of int ..._rate_invalid()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Getting a BAR can be an explanation if we're chasing packet loss. Add a
print with the relevant debug level in that code path.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.913e989a1751.I6bff9020e339d91b61b5ad6aede27bcf8c7e6819@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Transition to d3 is much faster if there is no power save during the
transition. Therefore a new flag was added to the device power cmd to
indicate the power save isn't allowed until the transition is completed.
Set this flag in _iwl_mvm_suspend, when the transition begins.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.ced036106507.Ib5ed5a47ee35f624902bd8882dde3e559285965b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware crashes in the de-activation / re-activation
of the link during CSA, we will not have a valid phy_ctxt
pointer in mvmvif. This is a legit case, but when mac80211
removes the station to cleanup our state during the
re-configuration, we need to make sure we clear ap_sta
otherwise we won't re-add the station after the firmware has
been restarted. Later on, we'd activate the link, try to send
a TLC command crash again on ASSERT 3508.
Fix this by properly cleaning up our state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.2651e6f6a55a.I4cd50e88ee5c23c1c8dd5b157a800e4b4c96f236@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently we are setting the rate in the tx cmd for
mgmt frames (e.g. during connection establishment).
This was problematic when sending mgmt frames in eSR mode,
as we don't know what link this frame will be sent on
(This is decided by the FW), so we don't know what is the
lowest rate.
Fix this by not setting the rate in tx cmd and rely
on FW to choose the right one.
Set rate only for injected frames with fixed rate,
or when no sta is given.
Also set for important frames (EAPOL etc.) the High Priority flag.
Fixes: 055b22e770 ("iwlwifi: mvm: Set Tx rate and flags when there is not station")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.6c7e59620ee0.I6eaed3ccdd6dd62b9e664facc484081fc5275843@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the channel bandwidth is greater or equal than 80MHz,
enable FILS DF transmittion, even if the control channel is non-PSC.
That's because that in 80MHz there must be a sub 20MHz PSC
channel, and since the FILS DF is duplicated on all sub 20MHz
channels, within the 80MHz (hence it will be sent on a PSC channel).
Also, if FILS DF Tx is enabled, always configure the firmware
with the actual channel bandwidth, even before there is a connected
client (rather than the minimum bandwidth e.g. 20MHz), since FILS
DF transmission on a PSC channel take presedent over power
consumption.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.83b9a76fc6c4.I6703111cc6befcd0e9cd9adf3cb127a648dbb7b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device initialized with ME active, this would indeed
work, since the NVM information would be obtained from ME.
However, in the much more likely case that ME isn't active
and the firmware takes actions requiring the sync, this was
not working correctly when the firmware is only run at init
to obtain NVM data, since mac80211 isn't even initialized.
Fix this by moving the 'pldr_sync' handling to a different
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.45a94d480e56.Id9277f1df6a63ab0dfca0d0c0f448c759e1b8e73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable the TOP (HW part) fatal error interrupt and add a
print when it happens. Currently FW always adds also the
SW error interrupt, but for >= Bz we'll need to do PLDR
in case this is asserted, so leave a TODO item already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.127d914a4d0d.I41ea409df63474554ef727c49382d0b5bf15939e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the hardware is not responding, as indicated by (currently)
five consecutive HW errors during reading, then just give up
and fail, rather than attempting forever and forever for this
to not return any useful data anyway.
Even though we no longer completely deadlock the machine if it
takes a long time, we still make it pretty much unusable since
we'll eventually hold the RTNL while waiting for this process
to finish.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.345af79f431c.I5ecde6b76b1e3a1572bd59d3cf8f827e767cedeb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the bus has no parent due to the topology, the device rescan
(after some kind of reset was detected) wouldn't work. On the
other hand, some platforms appear to require scanning the parent,
though it's not clear why.
However if there's no parent, then we skip the rescan, which isn't a
good idea. Change the code to go to the parent only if that exists,
and rescan the bus itself where it doesn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.f7795a1ccdab.I2b84810a743469a1bcabf3628262cf54311593f4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We always check whether combo PHYs need to be re-initialized
after disabling DC states, which leads to log spam. Switch things
around so that we only log something when we actually have to
re-initialized a PHY.
The log spam was exacerbated by commit 41b4c7fe72 ("drm/i915:
Disable DC states for all commits") since we now disable DC
states far more often.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230502143906.2401-12-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
