There is a period of time between the psmouse deactivate and the
ability to communicate with the SMBus companion. Insert a
sleep after the deactivate to account for the delay and ensure
the SMBus companion is responsive.
Attempting to read from the SMBus companion too quickly was causing
the touchpad on machines with an i801_smbus companion to stop working
after a sleep/resume cycle.
On resume the rmi4_smbus would fail with errors reading the SMBus version
number:
```
[5454] i2c_i801:i801_check_post:414: i801_smbus 0000:00:1f.3: No response
smbus_result: i2c-0 a=02c f=0000 c=fd BYTE_DATA rd res=-6
rmi4_smbus 0-002c: failed to get SMBus version number!
...
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -6.
rmi4_f01 rmi4-00.fn01: Resume failed with code -6.
rmi4_physical rmi4-00: Failed to suspend functions: -6
rmi4_smbus 0-002c: Failed to resume device: -6
```
In this case the rmi_smb_get_version fails with -ENXIO if it happens too
soon after the preceding serio_resume -> psmouse_deactivate call.
On boot this issue could cause the touchpad to stay in the limited PS/2
mode. This only reproduced in 1 in 10 boots on the Lenovo T440p.
Failures in the log on boot would show up as:
```
psmouse serio1: synaptics: Trying to set up SMBus access
[122] i2c_i801:i801_check_post:437: i801_smbus 0000:00:1f.3: No response
psmouse serio1: synaptics: SMbus companion is not ready yet
```
Experimentation on the Lenovo T440p showed that a delay of 7-12ms on
resume allowed the companion to respond.
The 30ms delay in this patch was chosen based on the linux-input message:
Link: https://lore.kernel.org/all/BYAPR03MB47572F2C65E52ED673238D41B2439@BYAPR03MB4757.namprd03.prod.outlook.com/
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/20230726025256.81174-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On TGP, the RTC (always running) was reduced from 3MHz to 32KHz.
As a result of this change, when HPD active going low pulse or HPD IRQ
is presented and the refclk (19.2MHz) is not toggling already toggling,
there is a 60 to 90us synchronization delay which effectively reduces
the duration of the IRQ pulse to less than the programmed 500us filter
value and the hot plug interrupt is NOT registered.
Solution was to Reduce SHPD_FILTER to 250us for ADL and above.
This solution was derived when the below patch was floated.
[1]https://patchwork.freedesktop.org/patch/532187
and after some internal discussion Ville's suggestion made sense.
Bspec: 68970
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230720104624.3063544-1-suraj.kandpal@intel.com
This patch allows users to set up MIDI 1.0 ports more flexibly.
Namely, instead of the fixed mapping only from FB 0, now multiple
block definitions are applied to build up the MIDI 1.0 mapping.
The each block config has midi1_first_group and midi1_num_groups
attributes, and those specify which Groups are used for MIDI 1.0.
Those fields must be within the UMP Groups defined in the block
itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-8-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new ALSA control element to watch the current operation mode
(MIDI 1.0 or MIDI 2.0). It's a read-only control that reflects the
current value of altsetting, and 0 means unused, 1 for MIDI 1.0
(altset 0) and 2 for MIDI 2.0 (altset 1).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-7-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends MIDI 2.0 function driver to add more proper support
for MIDI 1.0 interface. Before this patch, the driver only exposes
the USB descriptor of a MIDI 1.0 interface in altset 0 while no actual
I/O is running for it. This patch enables the actual I/O for the
altset 0; the backend UMP rawmidi is translated from/to the MIDI 1.0
USB commands.
For converting to USB MIDI 1.0 data protocol, a helper function is
copied from the existing f_midi driver, in addition to a few other UMP
Core helper functions. For the MIDI 1.0 OUT (that is, input for
gadget), the incoming USB MIDI 1.0 packet is translated to UMP packets
via UMP Core helper, and tossed to the attached UMP rawmidi. It's a
relatively straightforward. OTOH, for MIDI 1.0 IN (i.e. output for
gadget), it's a bit more complex: we need to convert a source UMP
packet once to the standard MIDI 1.0 byte stream, and convert it again
to USB MIDI 1.0 packets, then send them out.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-5-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends MIDI 2.0 function driver to deal with more MIDI1
Jacks depending on the given Block configuration.
For MIDI 1.0, we take the configuration given in Function Block 0, and
create MIDI Jacks and Endpoints depending on the definition there.
That is, when more UMP Groups are defined in the Block 0, the
corresponding MIDI1 Jacks will be created.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-4-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support of configfs to MIDI 2.0 function driver
for users to allow configuring the UMP Endpoint and Function Blocks
more flexibly. The configuration is in a tree form. The top-most
contains some card-level configurations. UMP Endpoints are defined in
subdirectories (ep.0, ep.1, etc) that contain Endpoint-specific
configurations such as ep_name, etc. And, UMP Function Blocks are
defined in the subdirectories (block.0, block.1, etc) under EP
subdirectory. As default, the driver creates a single UMP Endpoint
(ep.0) and a single Function Block (block.0) to work in a minimalistic
manner. User can modify those attributes freely to fit with the
demands.
When multiple Function Blocks are required, user can create another
directory as block.1, block.2, and so on (up to block.31). A block.*
directory can be deleted dynamically, too. A caveat is that the block
number has to be continuous.
Similarly, when multiple UMP Endpoints are required, user can create
another directory as ep.1, ep.2, up to ep.3.
Also, some driver behavior can be controlled in the card top-level
configs. e.g. you can pass process_ump=0 to disable the processing of
UMP Stream messages. This would be equivalent with the older MIDI 2.0
spec that doesn't support UMP v1.1 features.
The configfs interface checks upper- / lower-bound of input values,
and more sanity checks are performed at binding.
Attributes can't be changed any longer once when the instance is
linked to UDC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support for USB MIDI 2.0 gadget function driver.
The driver emulates a USB MIDI 2.0 interface with one or more UMP
Endpoints, where each of UMP Endpoint is a pair of MIDI Endpoints for
handling MIDI 2.0 UMP packets. When the function driver is bound, the
driver creates an ALSA card object with UMP rawmidi devices. This is
a kind of loop-back where the incoming and upcoming UMP packets
from/to the MIDI 2.0 UMP Endpoints are transferred as-is. In
addition, legacy (MIDI 1.0) rawmidi devices are created, so that
legacy applications can work in the gadget side, too.
When a USB MIDI 2.0 gadget interface appears, the connected host can
use it with the snd-usb-audio driver where MIDI 2.0 support is
enabled. Both gadget and connected hosts will have the similar UMP
Endpoint and Function Block (or Group Terminal Block) information.
Slight differences are the direction and UI-hint bits; it's due to the
nature of gadget driver, and the input/output direction is swapped in
both sides (the input for gadget is the output for host, and vice
versa).
The driver supports the brand-new UMP v1.1 feature, including the UMP
Stream message handling for providing UMP Endpoint and Function Block
information as well as dealing with the MIDI protocol switch. The
driver responds to UMP Stream messages by itself. OTOH, MIDI-CI
message handling isn't implemented in the kernel driver; it should be
processed in the user-space through the loopback UMP device.
As of this patch, the whole configuration is fixed, providing only one
bidirectional UMP Endpoint containing a single FB/GTB with a single
UMP Group. The configuration will be dynamically changeable in the
following patches.
The traditional MIDI 1.0 is still provided in the altset 0 (which is
mandatory per spec). But it's only about the configuration, and no
actual I/O will be running for the altset 0 as of this patch. The
proper support MIDI 1.0 altset will follow in later patches, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 3.0 PHY transceiver.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-5-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 2.0 PHY transceiver.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-4-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-3-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-2-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Realtek SoC, the parameter of usb phy is designed to can dynamic
tuning base on port status. Therefore, add a notify callback of phy
driver when usb port status change.
The Realtek phy driver is designed to dynamically adjust disconnection
level and calibrate phy parameters. When the device connected bit changes
and when the disconnected bit changes, do port status change notification:
Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
USB_PORT_STAT_C_CONNECTION.
1. The device is connected, the driver lowers the disconnection level and
calibrates the phy parameters.
2. The device disconnects, the driver increases the disconnect level and
calibrates the phy parameters.
When controller to notify connect that device is already ready. If we
adjust the disconnection level in notify_connect, the disconnect may have
been triggered at this stage. So we need to change that as early as
possible. The status change of connection is before port reset.
Therefore, we add an api to notify phy the port status changes. In this
stage, the device is not port enable, and it will not trigger
disconnection.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Nguyen says:
====================
ice: switchdev bridge offload
Wojciech Drewek says:
Linux bridge provides ability to learn MAC addresses and vlans
detected on bridge's ports. As a result of this, FDB (forward data base)
entries are created and they can be offloaded to the HW. By adding
VF's port representors to the bridge together with the uplink netdev,
we can learn VF's and link partner's MAC addresses. This is achieved
by slow/exception-path, where packets that do not match any filters
(FDB entries in this case) are send to the bridge ports.
Driver keeps track of the netdevs added to the bridge
by listening for NETDEV_CHANGEUPPER event. We distinguish two types
of bridge ports: uplink port and VF's representor port. Linux
bridge always learns src MAC of the packet on rx path. With the
current slow-path implementation, it means that we will learn
VF's MAC on port repr (when the VF transmits the packet) and
link partner's MAC on uplink (when we receive it on uplink from LAN).
The driver is notified about learning of the MAC/VLAN by
SWITCHDEV_FDB_{ADD|DEL}_TO_DEVICE events. This is followed by creation
of the HW filter. The direction of the filter is based on port
type (uplink or VF repr). In case of the uplink, rule forwards
the packets to the LAN (matching on link partner's MAC). When the
notification is received on VF repr then the rule forwards the
packets to the associated VF (matching on VF's MAC).
This approach would not work on its own however. This is because if
one of the directions is offloaded, then the bridge would not be able
to learn the other one. If the egress rule is added (learned on uplink)
then the response from the VF will be sent directly to the LAN.
The packet will not got through slow-path, it would not be seen on
VF's port repr. Because of that, the bridge would not learn VF's MAC.
This is solved by introducing guard rule. It prevents forward rule from
working until the opposite direction is offloaded.
Aging is not fully supported yet, aging time is static for now. The
follow up submissions will introduce counters that will allow us to
keep track if the rule is actually being used or not.
A few fixes/changes are needed for this feature to work with ice driver.
These are introduced in first 5 patches.
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: add tracepoints for the switchdev bridge
ice: implement static version of ageing
ice: implement bridge port vlan
ice: Add VLAN FDB support in switchdev mode
ice: Add guard rule when creating FDB in switchdev
ice: Switchdev FDB events support
ice: Implement basic eswitch bridge setup
ice: Unset src prune on uplink VSI
ice: Disable vlan pruning for uplink VSI
ice: Don't tx before switchdev is fully configured
ice: Prohibit rx mode change in switchdev mode
ice: Skip adv rules removal upon switchdev release
====================
Link: https://lore.kernel.org/r/20230724161152.2177196-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to check the availability of fprobe and kprobes for
add_remove_btfarg.tc.
Only if both kprobe and fprobe are not supported, it should return
"unsupported".
Link: https://lore.kernel.org/all/169024904889.395371.17998733386857387118.stgit@devnote2/
Fixes: 4231f30fcc ("selftests/ftrace: Add BTF arguments test cases")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Since find_btf_func_param() abd btf_type_by_id() can return NULL,
the caller must check the return value correctly.
Link: https://lore.kernel.org/all/169024903951.395371.11361556840733470934.stgit@devnote2/
Fixes: b576e09701 ("tracing/probes: Support function parameters if BTF is available")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional path latency, as described in the publicly available
datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register, since the Phy
framework currently does not support querying the Phy ingress and egress
latency. The Closs Domain Crossing Circuits errors as indicated in [1]
are already being accounted in the stmmac_get_tx_hwtstamp() function and
are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Last year, the code that manages GSI channel transactions switched
from using spinlock-protected linked lists to using indexes into the
ring buffer used for a channel. Recently, Google reported seeing
transaction reference count underflows occasionally during shutdown.
Doug Anderson found a way to reproduce the issue reliably, and
bisected the issue to the commit that eliminated the linked lists
and the lock. The root cause was ultimately determined to be
related to unused transactions being committed as part of the modem
shutdown cleanup activity. Unused transactions are not normally
expected (except in error cases).
The modem uses some ranges of IPA-resident memory, and whenever it
shuts down we zero those ranges. In ipa_filter_reset_table() a
transaction is allocated to zero modem filter table entries. If
hashing is not supported, hashed table memory should not be zeroed.
But currently nothing prevents that, and the result is an unused
transaction. Something similar occurs when we zero routing table
entries for the modem.
By preventing any attempt to clear hashed tables when hashing is not
supported, the reference count underflow is avoided in this case.
Note that there likely remains an issue with properly freeing unused
transactions (if they occur due to errors). This patch addresses
only the underflows that Google originally reported.
Cc: <stable@vger.kernel.org> # 6.1.x
Fixes: d338ae28d8 ("net: ipa: kill all other transaction lists")
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230724224055.1688854-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzkaller found a bug in unix_bind_bsd() [0]. We can reproduce it
by bind()ing a socket on a path with length 108.
108 is the size of sun_addr of struct sockaddr_un and is the maximum
valid length for the pathname socket. When calling bind(), we use
struct sockaddr_storage as the actual buffer size, so terminating
sun_addr[108] with null is legitimate as done in unix_mkname_bsd().
However, strlen(sunaddr) for such a case causes fortify_panic() if
CONFIG_FORTIFY_SOURCE=y. __fortify_strlen() has no idea about the
actual buffer size and see the string as unterminated.
Let's use strnlen() to allow sun_addr to be unterminated at 107.
[0]:
detected buffer overflow in __fortify_strlen
kernel BUG at lib/string_helpers.c:1031!
Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 255 Comm: syz-executor296 Not tainted 6.5.0-rc1-00330-g60cc1f7d0605 #4
Hardware name: linux,dummy-virt (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : fortify_panic+0x1c/0x20 lib/string_helpers.c:1030
lr : fortify_panic+0x1c/0x20 lib/string_helpers.c:1030
sp : ffff800089817af0
x29: ffff800089817af0 x28: ffff800089817b40 x27: 1ffff00011302f68
x26: 000000000000006e x25: 0000000000000012 x24: ffff800087e60140
x23: dfff800000000000 x22: ffff800089817c20 x21: ffff800089817c8e
x20: 000000000000006c x19: ffff00000c323900 x18: ffff800086ab1630
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000001
x14: 1ffff00011302eb8 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 64a26b65474d2a00
x8 : 64a26b65474d2a00 x7 : 0000000000000001 x6 : 0000000000000001
x5 : ffff800089817438 x4 : ffff800086ac99e0 x3 : ffff800080f19e8c
x2 : 0000000000000001 x1 : 0000000100000000 x0 : 000000000000002c
Call trace:
fortify_panic+0x1c/0x20 lib/string_helpers.c:1030
_Z16__fortify_strlenPKcU25pass_dynamic_object_size1 include/linux/fortify-string.h:217 [inline]
unix_bind_bsd net/unix/af_unix.c:1212 [inline]
unix_bind+0xba8/0xc58 net/unix/af_unix.c:1326
__sys_bind+0x1ac/0x248 net/socket.c:1792
__do_sys_bind net/socket.c:1803 [inline]
__se_sys_bind net/socket.c:1801 [inline]
__arm64_sys_bind+0x7c/0x94 net/socket.c:1801
__invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
invoke_syscall+0x98/0x2c0 arch/arm64/kernel/syscall.c:52
el0_svc_common+0x134/0x240 arch/arm64/kernel/syscall.c:139
do_el0_svc+0x64/0x198 arch/arm64/kernel/syscall.c:188
el0_svc+0x2c/0x7c arch/arm64/kernel/entry-common.c:647
el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:665
el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591
Code: aa0003e1 d0000e80 91030000 97ffc91a (d4210000)
Fixes: df8fc4e934 ("kbuild: Enable -fstrict-flex-arrays=3")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230724213425.22920-2-kuniyu@amazon.com
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mdiobus_is_registered_device() doesn't checking that "addr" was valid
before dereferencing bus->mdio_map[]. Extract the code that checks
this from mdiobus_get_phy(), and use it here as well.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qNxvu-00111m-1V@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last s390 machine that supported FDDI was z900 ('7th generation',
released in 2000). The oldest machine generation currently supported by
the Linux kernel is MARCH_Z10 (released 2008). If there is still a usecase
for connecting a Linux on s390 instance to a LAN Channel Station (LCS), it
can only do so via Ethernet.
Randy Dunlap[1] found that LCS over FDDI has never worked, when FDDI
was compiled as module. Instead of fixing that, remove the FDDI option
from the lcs driver.
While at it, make the CONFIG_LCS description a bit more helpful.
References:
[1] https://lore.kernel.org/netdev/20230621213742.8245-1-rdunlap@infradead.org/
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230724131546.3597001-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are currently two paths that call remove_xps_queue():
1. __netif_set_xps_queue -> remove_xps_queue
2. clean_xps_maps -> remove_xps_queue_cpu -> remove_xps_queue
There is no need to check dev_maps in remove_xps_queue() because
dev_maps has been checked on these two paths.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20230724023735.2751602-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit 954d1fa1ac ("macvlan: Add netlink attribute for
broadcast cutoff") added one additional attribute named
IFLA_MACVLAN_BC_CUTOFF to allow broadcast cutfoff.
However, it forgot to describe the nla_policy at macvlan_policy
(drivers/net/macvlan.c). Hence, this suppose NLA_S32 (4 bytes) integer
can be faked as empty (0 bytes) by a malicious user, which could leads
to OOB in heap just like CVE-2023-3773.
To fix it, this commit just completes the nla_policy description for
IFLA_MACVLAN_BC_CUTOFF. This enforces the length check and avoids the
potential OOB read.
Fixes: 954d1fa1ac ("macvlan: Add netlink attribute for broadcast cutoff")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230723080205.3715164-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a problem occurs in the process of creating an integrity payload, the
status of bio is always BLK_STS_RESOURCE.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jinyoung Choi <j-young.choi@samsung.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230725051839epcms2p8e4d20ad6c51326ad032e8406f59d0aaa@epcms2p8
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If pm8001_init_sas_add() fails, return error code in pm8001_pci_probe().
Fixes: 14a8f116cd ("scsi: pm80xx: Add GET_NVMD timeout during probe")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230725125706.566990-1-yangyingliang@huawei.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Storage devices are free to send RSCNs, e.g. for internal state changes. If
this happens on all connected paths, zfcp risks temporarily losing all
paths at the same time. This has strong requirements on multipath
configuration such as "no_path_retry queue".
Avoid such situations by deferring fc_rport blocking until after the ADISC
response, when any actual state change of the remote port became clear.
The already existing port recovery triggers explicitly block the fc_rport.
The triggers are: on ADISC reject or timeout (typical cable pull case), and
on ADISC indicating that the remote port has changed its WWPN or
the port is meanwhile no longer open.
As a side effect, this also removes a confusing direct function call to
another work item function zfcp_scsi_rport_work() instead of scheduling
that other work item. It was probably done that way to have the rport block
side effect immediate and synchronous to the caller.
Fixes: a2fa0aede0 ("[SCSI] zfcp: Block FC transport rports early on errors")
Cc: stable@vger.kernel.org #v2.6.30+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Fedor Loshakov <loshakov@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Link: https://lore.kernel.org/r/20230724145156.3920244-1-maier@linux.ibm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are three places that qla4xxx parses nlattrs:
- qla4xxx_set_chap_entry()
- qla4xxx_iface_set_param()
- qla4xxx_sysfs_ddb_set_param()
and each of them directly converts the nlattr to specific pointer of
structure without length checking. This could be dangerous as those
attributes are not validated and a malformed nlattr (e.g., length 0) could
result in an OOB read that leaks heap dirty data.
Add the nla_len check before accessing the nlattr data and return EINVAL if
the length check fails.
Fixes: 26ffd7b45f ("[SCSI] qla4xxx: Add support to set CHAP entries")
Fixes: 1e9e2be3ee ("[SCSI] qla4xxx: Add flash node mgmt support")
Fixes: 00c31889f7 ("[SCSI] qla4xxx: fix data alignment and use nl helpers")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20230723080053.3714534-1-linma@zju.edu.cn
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
beiscsi_iface_set_param() parses nlattr with nla_for_each_attr and assumes
every attributes can be viewed as struct iscsi_iface_param_info.
This is not true because there is no any nla_policy to validate the
attributes passed from the upper function iscsi_set_iface_params().
Add the nla_len check before accessing the nlattr data and return EINVAL if
the length check fails.
Fixes: 0e43895ec1 ("[SCSI] be2iscsi: adding functionality to change network settings using iscsiadm")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20230723075938.3713864-1-linma@zju.edu.cn
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functions iscsi_if_set_param() and iscsi_if_set_host_param() convert an
nlattr payload to type char* and then call C string handling functions like
sscanf and kstrdup:
char *data = (char*)ev + sizeof(*ev);
...
sscanf(data, "%d", &value);
However, since the nlattr is provided by the user-space program and the
nlmsg skb is allocated with GFP_KERNEL instead of GFP_ZERO flag (see
netlink_alloc_large_skb() in netlink_sendmsg()), dirty data on the heap can
lead to an OOB access for those string handling functions.
By investigating how the bug is introduced, we find it is really
interesting as the old version parsing code starting from commit
fd7255f51a ("[SCSI] iscsi: add sysfs attrs for uspace sync up") treated
the nlattr as integer bytes instead of string and had length check in
iscsi_copy_param():
if (ev->u.set_param.len != sizeof(uint32_t))
BUG();
But, since the commit a54a52caad ("[SCSI] iscsi: fixup set/get param
functions"), the code treated the nlattr as C string while forgetting to
add any strlen checks(), opening the possibility of an OOB access.
Fix the potential OOB by adding the strlen() check before accessing the
buf. If the data passes this check, all low-level set_param handlers can
safely treat this buf as legal C string.
Fixes: fd7255f51a ("[SCSI] iscsi: add sysfs attrs for uspace sync up")
Fixes: 1d9bf13a9c ("[SCSI] iscsi class: add iscsi host set param event")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20230723075820.3713119-1-linma@zju.edu.cn
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current NETLINK_ISCSI netlink parsing loop checks every nlmsg to make
sure the length is bigger than sizeof(struct iscsi_uevent) and then calls
iscsi_if_recv_msg().
nlh = nlmsg_hdr(skb);
if (nlh->nlmsg_len < sizeof(*nlh) + sizeof(*ev) ||
skb->len < nlh->nlmsg_len) {
break;
}
...
err = iscsi_if_recv_msg(skb, nlh, &group);
Hence, in iscsi_if_recv_msg() the nlmsg_data can be safely converted to
iscsi_uevent as the length is already checked.
However, in other cases the length of nlattr payload is not checked before
the payload is converted to other data structures. One example is
iscsi_set_path() which converts the payload to type iscsi_path without any
checks:
params = (struct iscsi_path *)((char *)ev + sizeof(*ev));
Whereas iscsi_if_transport_conn() correctly checks the pdu_len:
pdu_len = nlh->nlmsg_len - sizeof(*nlh) - sizeof(*ev);
if ((ev->u.send_pdu.hdr_size > pdu_len) ..
err = -EINVAL;
To sum up, some code paths called in iscsi_if_recv_msg() do not check the
length of the data (see below picture) and directly convert the data to
another data structure. This could result in an out-of-bound reads and heap
dirty data leakage.
_________ nlmsg_len(nlh) _______________
/ \
+----------+--------------+---------------------------+
| nlmsghdr | iscsi_uevent | data |
+----------+--------------+---------------------------+
\ /
iscsi_uevent->u.set_param.len
Fix the issue by adding the length check before accessing it. To clean up
the code, an additional parameter named rlen is added. The rlen is
calculated at the beginning of iscsi_if_recv_msg() which avoids duplicated
calculation.
Fixes: ac20c7bf07 ("[SCSI] iscsi_transport: Added Ping support")
Fixes: 43514774ff ("[SCSI] iscsi class: Add new NETLINK_ISCSI messages for cnic/bnx2i driver.")
Fixes: 1d9bf13a9c ("[SCSI] iscsi class: add iscsi host set param event")
Fixes: 01cb225dad ("[SCSI] iscsi: add target discvery event to transport class")
Fixes: 264faaaa12 ("[SCSI] iscsi: add transport end point callbacks")
Fixes: fd7255f51a ("[SCSI] iscsi: add sysfs attrs for uspace sync up")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20230725024529.428311-1-linma@zju.edu.cn
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only call scsi_set_resid() in case of an underflow. Do not call
scsi_set_resid() in case of an overflow.
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Fixes: cb38845d90 ("scsi: ufs: core: Set the residual byte count")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230724200843.3376570-2-bvanassche@acm.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although the code for residual handling in the SRP initiator follows the
SCSI documentation, that documentation has never been correct. Because
scsi_finish_command() starts from the data buffer length and subtracts the
residual, scsi_set_resid() must not be called if a residual overflow
occurs. Hence remove the scsi_set_resid() calls from the SRP initiator if a
residual overflow occurrs.
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Fixes: 9237f04e12 ("scsi: core: Fix scsi_get/set_resid() interface")
Fixes: e714531a34 ("IB/srp: Fix residual handling")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230724200843.3376570-3-bvanassche@acm.org
Acked-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change removed the only user of a local variable that needs to now
also be removed:
drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_mcq_esi_handler':
drivers/ufs/host/ufs-qcom.c:1652:31: error: unused variable 'host' [-Werror=unused-variable]
Fixes: 8f2b78652d ("scsi: ufs: qcom: Get queue ID from MSI index in ESI handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/llvm/64c00cd4.630a0220.6ad79.0eac@mx.google.com/
Link: https://lore.kernel.org/r/20230724122029.1430482-1-arnd@kernel.org
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Splitting these out into separate helper functions means that we
actually pass an uninitialized variable into another function call
if dec_active() happens to not be inlined, and CONFIG_PREEMPT_RT
is disabled:
kernel/bpf/memalloc.c: In function 'add_obj_to_free_list':
kernel/bpf/memalloc.c:200:9: error: 'flags' is used uninitialized [-Werror=uninitialized]
200 | dec_active(c, flags);
Avoid this by passing the flags by reference, so they either get
initialized and dereferenced through a pointer, or the pointer never
gets accessed at all.
Fixes: 18e027b1c7 ("bpf: Factor out inc/dec of active flag into helpers.")
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230725202653.2905259-1-arnd@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jiri Olsa says:
====================
bpf: Disable preemption in perf_event_output helpers code
hi,
we got report of kernel crash [1][3] within bpf_event_output helper.
The reason is the nesting protection code in bpf_event_output that expects
disabled preemption, which is not guaranteed for programs executed by
bpf_prog_run_array_cg.
I managed to reproduce on tracing side where we have the same problem
in bpf_perf_event_output. The reproducer [2] just creates busy uprobe
and call bpf_perf_event_output helper a lot.
v3 changes:
- added acks and fixed 'Fixes' tag style [Hou Tao]
- added Closes tag to patch 2
v2 changes:
- I changed 'Fixes' commits to where I saw we switched from preempt_disable
to migrate_disable, but I'm not completely sure about the patch 2, because
it was tricky to find, would be nice if somebody could check on that
thanks,
jirka
[1] https://github.com/cilium/cilium/issues/26756
[2] https://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf.git/commit/?h=bpf_output_fix_reproducer&id=8054dcc634121b884c7c331329d61d93351d03b5
[3] slack:
[66194.378161] BUG: kernel NULL pointer dereference, address: 0000000000000001
[66194.378324] #PF: supervisor instruction fetch in kernel mode
[66194.378447] #PF: error_code(0x0010) - not-present page
...
[66194.378692] Oops: 0010 [#1] PREEMPT SMP NOPTI
...
[66194.380666] <TASK>
[66194.380775] ? perf_output_sample+0x12a/0x9a0
[66194.380902] ? finish_task_switch.isra.0+0x81/0x280
[66194.381024] ? perf_event_output+0x66/0xa0
[66194.381148] ? bpf_event_output+0x13a/0x190
[66194.381270] ? bpf_event_output_data+0x22/0x40
[66194.381391] ? bpf_prog_dfc84bbde731b257_cil_sock4_connect+0x40a/0xacb
[66194.381519] ? xa_load+0x87/0xe0
[66194.381635] ? __cgroup_bpf_run_filter_sock_addr+0xc1/0x1a0
[66194.381759] ? release_sock+0x3e/0x90
[66194.381876] ? sk_setsockopt+0x1a1/0x12f0
[66194.381996] ? udp_pre_connect+0x36/0x50
[66194.382114] ? inet_dgram_connect+0x93/0xa0
[66194.382233] ? __sys_connect+0xb4/0xe0
[66194.382353] ? udp_setsockopt+0x27/0x40
[66194.382470] ? __pfx_udp_push_pending_frames+0x10/0x10
[66194.382593] ? __sys_setsockopt+0xdf/0x1a0
[66194.382713] ? __x64_sys_connect+0xf/0x20
[66194.382832] ? do_syscall_64+0x3a/0x90
[66194.382949] ? entry_SYSCALL_64_after_hwframe+0x72/0xdc
[66194.383077] </TASK>
---
====================
Link: https://lore.kernel.org/r/20230725084206.580930-1-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We received report [1] of kernel crash, which is caused by
using nesting protection without disabled preemption.
The bpf_event_output can be called by programs executed by
bpf_prog_run_array_cg function that disabled migration but
keeps preemption enabled.
This can cause task to be preempted by another one inside the
nesting protection and lead eventually to two tasks using same
perf_sample_data buffer and cause crashes like:
BUG: kernel NULL pointer dereference, address: 0000000000000001
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
...
? perf_output_sample+0x12a/0x9a0
? finish_task_switch.isra.0+0x81/0x280
? perf_event_output+0x66/0xa0
? bpf_event_output+0x13a/0x190
? bpf_event_output_data+0x22/0x40
? bpf_prog_dfc84bbde731b257_cil_sock4_connect+0x40a/0xacb
? xa_load+0x87/0xe0
? __cgroup_bpf_run_filter_sock_addr+0xc1/0x1a0
? release_sock+0x3e/0x90
? sk_setsockopt+0x1a1/0x12f0
? udp_pre_connect+0x36/0x50
? inet_dgram_connect+0x93/0xa0
? __sys_connect+0xb4/0xe0
? udp_setsockopt+0x27/0x40
? __pfx_udp_push_pending_frames+0x10/0x10
? __sys_setsockopt+0xdf/0x1a0
? __x64_sys_connect+0xf/0x20
? do_syscall_64+0x3a/0x90
? entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fixing this by disabling preemption in bpf_event_output.
[1] https://github.com/cilium/cilium/issues/26756
Cc: stable@vger.kernel.org
Reported-by: Oleg "livelace" Popov <o.popov@livelace.ru>
Closes: https://github.com/cilium/cilium/issues/26756
Fixes: 2a916f2f54 ("bpf: Use migrate_disable/enable in array macros and cgroup/lirc code.")
Acked-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20230725084206.580930-3-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The nesting protection in bpf_perf_event_output relies on disabled
preemption, which is guaranteed for kprobes and tracepoints.
However bpf_perf_event_output can be also called from uprobes context
through bpf_prog_run_array_sleepable function which disables migration,
but keeps preemption enabled.
This can cause task to be preempted by another one inside the nesting
protection and lead eventually to two tasks using same perf_sample_data
buffer and cause crashes like:
kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
BUG: unable to handle page fault for address: ffffffff82be3eea
...
Call Trace:
? __die+0x1f/0x70
? page_fault_oops+0x176/0x4d0
? exc_page_fault+0x132/0x230
? asm_exc_page_fault+0x22/0x30
? perf_output_sample+0x12b/0x910
? perf_event_output+0xd0/0x1d0
? bpf_perf_event_output+0x162/0x1d0
? bpf_prog_c6271286d9a4c938_krava1+0x76/0x87
? __uprobe_perf_func+0x12b/0x540
? uprobe_dispatcher+0x2c4/0x430
? uprobe_notify_resume+0x2da/0xce0
? atomic_notifier_call_chain+0x7b/0x110
? exit_to_user_mode_prepare+0x13e/0x290
? irqentry_exit_to_user_mode+0x5/0x30
? asm_exc_int3+0x35/0x40
Fixing this by disabling preemption in bpf_perf_event_output.
Cc: stable@vger.kernel.org
Fixes: 8c7dcb84e3 ("bpf: implement sleepable uprobes by chaining gps")
Acked-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20230725084206.580930-2-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
__symbol_put() is really meant as an internal helper and is not available
when module unloading is disabled, unlike the previously used symbol_put():
samples/hw_breakpoint/data_breakpoint.c: In function 'hw_break_module_exit':
samples/hw_breakpoint/data_breakpoint.c:73:9: error: implicit declaration of function '__symbol_put'; did you mean '__symbol_get'? [-Werror=implicit-function-declaration]
The hw_break_module_exit() function is not actually used when module
unloading is disabled, but it still causes the build failure for an
undefined identifier. Enclose this one call in an appropriate #ifdef to
clarify what the requirement is. Leaving out the entire exit function
would also work but feels less clar in this case.
Fixes: 910e230d5f ("samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'")
Fixes: d8a84d33a4 ("samples/hw_breakpoint: drop use of kallsyms_lookup_name()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
The variable 'rv' is set to 0 after calling of_property_read_reg(), so
it cannot be used as an error code. Change to using correct error codes
in the error path.
Fixes: d0b2461678 ("ata: Use of_property_read_reg() to parse "reg"")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Conor Dooley <conor.dooley@microchip.com> says:
Based on my latest iteration of deprecating riscv,isa [1], here's an
implementation of the new properties for Linux. The first few patches,
up to "RISC-V: split riscv_fill_hwcap() in 3", are all prep work that
further tames some of the extension related code, on top of my already
applied series that cleans up the ISA string parser.
Perhaps "RISC-V: shunt isa_ext_arr to cpufeature.c" is a bit gratuitous,
but I figured a bit of coalescing of extension related data structures
would be a good idea. Note that riscv,isa will still be used in the
absence of the new properties. Palmer suggested adding a Kconfig option
to turn off the fallback for DT, which I have gone and done. It's locked
behind the NONPORTABLE option for good reason.
* b4-shazam-merge:
RISC-V: provide Kconfig & commandline options to control parsing "riscv,isa"
RISC-V: try new extension properties in of_early_processor_hartid()
RISC-V: enable extension detection from dedicated properties
RISC-V: split riscv_fill_hwcap() in 3
RISC-V: add single letter extensions to riscv_isa_ext
RISC-V: add missing single letter extension definitions
RISC-V: repurpose riscv_isa_ext array in riscv_fill_hwcap()
RISC-V: shunt isa_ext_arr to cpufeature.c
RISC-V: drop a needless check in print_isa_ext()
RISC-V: don't parse dt/acpi isa string to get rv32/rv64
RISC-V: Provide a more helpful error message on invalid ISA strings
Link: https://lore.kernel.org/r/20230713-target-much-8ac624e90df8@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
As it says on the tin, provide Kconfig option to control parsing the
"riscv,isa" devicetree property. If either option is used, the kernel
will fall back to parsing "riscv,isa", where "riscv,isa-base" and
"riscv,isa-extensions" are not present.
The Kconfig options are set up so that the default kernel configuration
will enable the fallback path, without needing the commandline option.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Suggested-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-aviator-plausibly-a35662485c2c@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To fully deprecate the kernel's use of "riscv,isa",
of_early_processor_hartid() needs to first try using the new properties,
before falling back to "riscv,isa".
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-tablet-jimmy-987fea0eb2e1@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add support for parsing the new riscv,isa-extensions property in
riscv_fill_hwcap(), by means of a new "property" member of the
riscv_isa_ext_data struct. For now, this shadows the name of the
extension for all users, however this may not be the case for all
extensions, based on how the dt-binding is written.
For the sake of backwards compatibility, fall back to the old scheme
if the new properties are not detected. For now, just inform, rather
than warn, when that happens.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-vocation-profane-39a74b3c2649@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Before adding more complexity to it, split riscv_fill_hwcap() into 3
distinct sections:
- riscv_fill_hwcap() still is the top level function, into which the
additional complexity will be added.
- riscv_fill_hwcap_from_isa_string() handles getting the information
from the riscv,isa/ACPI equivalent across harts & the various quirks
there
- riscv_parse_isa_string() does what it says on the tin.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-daylight-puritan-37aeb41a4d9b@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
So that riscv_fill_hwcap() can use riscv_isa_ext to probe for single
letter extensions, add them to it.
As a result, what gets spat out in /proc/cpuinfo will become borked, as
single letter extensions will be printed as part of the base extensions
and while printing from riscv_isa_arr. Take the opportunity to unify the
printing of the isa string, using the new member of riscv_isa_ext_data
in the process.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-despite-bright-de00ac888cc7@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To facilitate adding single letter extensions to riscv_isa_ext, add
definitions for the extensions present in base_riscv_exts that do not
already have them.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-train-feisty-93de38250f98@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
