Remove the last two private vm_fault reasons: VM_FAULT_BADMAP and
VM_FAULT_BADACCESS.
In order to achieve this add an si_code parameter to do_no_context()
and it's wrappers and directly call the wrappers instead of relying on
do_fault_error() handling.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove VM_FAULT_SIGNAL and open-code it at the only two locations
where it is used.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove VM_FAULT_BADCONTEXT and instead call do_no_context() via
wrappers. This adds two new wrappers similar to what x86 has:
handle_fault_error() and handle_fault_error_nolock(). Both of them
simply call do_no_context(), while handle_fault_error() also unlocks
mmap lock, which avoids adding lots of mmap_read_unlock() calls with
this and subsequent patches.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
do_no_context() can be simplified by removing its fault parameter,
which is only used to decide if kfence_handle_page_fault() should be
called.
If the fault happened within the kernel space it is ok to always check
if this happened on a page which was unmapped because of the kfence
feature. Limiting the check to the VM_FAULT_BADCONTEXT case doesn't
add any value.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove duplicated fault error handling and handle it only once within
do_exception().
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
There is only one caller of do_low_address(). Given that this code is
quite special just get rid of do_low_address, and add it to
do_protection_exception() in order to make the code a bit more
readable.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Handling of VM_FAULT_PFAULT and VM_FAULT_BADCONTEXT is nearly identical;
the only difference is within do_no_context() where however the fault_type
(KERNEL_FAULT vs GMAP_FAULT) makes sure that both types will be handled
differently.
Therefore it is possible to get rid of VM_FAULT_PFAULT and use
VM_FAULT_BADCONTEXT instead.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The page table dumper uses get_kernel_nofault() to test if dereferencing
page table entries is possible. Use the result, which is the required page
table entry, instead of throwing it away and dereferencing a second time
without any safe guard.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Get rid of some magic numbers, and use the teid union and also some
ptrace PSW defines to improve readability.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move translation-exception identification structure to new fault.h
header file, change it to a union, and change existing kvm code
accordingly. The new union will be used by subsequent patches.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Generate slightly better code by using a static key to implement store
indication. This allows to get rid of a memory access on the hot path.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use the get_fault_address() helper function instead of open-coding it
at many locations.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
do_secure_storage_access() contains a switch statements which handles
all possible return values from get_fault_type(). Therefore remove the
pointless default case error handling and replace it with unreachable().
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove all noinline attribute from all functions and leave the
inlining decisions up to the compiler.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove unnecessary braces and also blanks after casts.
Add braces to have balanced braces where missing.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Just like other architectures make use __ratelimit() instead of
printk_ratelimit().
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove wrong, outdated, and pointless comments. Adjust wording for
some comments, and adjust whitespace at some places.
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Now that we have the ability to display the list of cores
with a feature when its selectivly enabled, lets convert
DBM to use that as well.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20231017052322.1211099-3-jeremy.linton@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The AMU feature can be enabled on a subset of the cores in a system.
Because of that, it prints a message for each core as it is detected.
This becomes tedious when there are hundreds of cores. Instead, for
CPU features which can be enabled on a subset of the present cores,
lets wait until update_cpu_capabilities() and print the subset of cores
the feature was enabled on.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Tested-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
Tested-by: Punit Agrawal <punit.agrawal@bytedance.com>
Link: https://lore.kernel.org/r/20231017052322.1211099-2-jeremy.linton@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mapping symbols emitted in the readelf output can confuse the
'faddr2line' symbol size calculation, resulting in the erroneous
rejection of valid offsets. This is especially prevalent when building
an arm64 kernel with CONFIG_CFI_CLANG=y, where most functions are
prefixed with a 32-bit data value in a '$d.n' section. For example:
447538: ffff800080014b80 548 FUNC GLOBAL DEFAULT 2 do_one_initcall
104: ffff800080014c74 0 NOTYPE LOCAL DEFAULT 2 $x.73
106: ffff800080014d30 0 NOTYPE LOCAL DEFAULT 2 $x.75
111: ffff800080014da4 0 NOTYPE LOCAL DEFAULT 2 $d.78
112: ffff800080014da8 0 NOTYPE LOCAL DEFAULT 2 $x.79
36: ffff800080014de0 200 FUNC LOCAL DEFAULT 2 run_init_process
Adding a warning to do_one_initcall() results in:
| WARNING: CPU: 0 PID: 1 at init/main.c:1236 do_one_initcall+0xf4/0x260
Which 'faddr2line' refuses to accept:
$ ./scripts/faddr2line vmlinux do_one_initcall+0xf4/0x260
skipping do_one_initcall address at 0xffff800080014c74 due to size mismatch (0x260 != 0x224)
no match for do_one_initcall+0xf4/0x260
Filter out these entries from readelf using a shell reimplementation of
is_mapping_symbol(), so that the size of a symbol is calculated as a
delta to the next symbol present in ksymtab.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20231002165750.1661-4-will@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
GNU utilities cannot necessarily parse objects built by LLVM, which can
result in confusing errors when using 'faddr2line':
$ CROSS_COMPILE=aarch64-linux-gnu- ./scripts/faddr2line vmlinux do_one_initcall+0xf4/0x260
aarch64-linux-gnu-addr2line: vmlinux: unknown type [0x13] section `.relr.dyn'
aarch64-linux-gnu-addr2line: DWARF error: invalid or unhandled FORM value: 0x25
do_one_initcall+0xf4/0x260:
aarch64-linux-gnu-addr2line: vmlinux: unknown type [0x13] section `.relr.dyn'
aarch64-linux-gnu-addr2line: DWARF error: invalid or unhandled FORM value: 0x25
$x.73 at main.c:?
Although this can be worked around by setting CROSS_COMPILE to "llvm=-",
it's cleaner to follow the same syntax as the top-level Makefile and
accept LLVM= as an indication to use the llvm- tools, optionally
specifying their location or specific version number.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20231002165750.1661-3-will@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
As Josh points out in 20230724234734.zy67gm674vl3p3wv@treble:
> Problem is, I think the kernel's symbol printing code prints the
> nearest kallsyms symbol, and there are some valid non-FUNC code
> symbols. For example, syscall_return_via_sysret.
so we shouldn't be considering only 'FUNC'-type symbols in the output
from readelf.
Drop the function symbol type filtering from the faddr2line outer loop.
Suggested-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20230724234734.zy67gm674vl3p3wv@treble
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20231002165750.1661-2-will@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add missing description of the atomic boolean in struct stm32f7_i2c_dev.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Yang Yingliang reported a memleak:
===
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888014aec078 (size 8):
comm "xrun", pid 356, jiffies 4294910619 (age 16.332s)
hex dump (first 8 bytes):
31 2d 30 30 31 63 00 00 1-001c..
backtrace:
[<00000000eb56c0a9>] __kmalloc_track_caller+0x1a6/0x300
[<000000000b220ea3>] kvasprintf+0xad/0x140
[<00000000b83203e5>] kvasprintf_const+0x62/0x190
[<000000002a5eab37>] kobject_set_name_vargs+0x56/0x140
[<00000000300ac279>] dev_set_name+0xb0/0xe0
[<00000000b66ebd6f>] i2c_new_client_device+0x7e4/0x9a0
If device_register() returns error in i2c_new_client_device(),
the name allocated by i2c_dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path.
===
I think this solution is less intrusive and more robust than he
originally proposed solutions, though.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Closes: http://patchwork.ozlabs.org/project/linux-i2c/patch/20221124085448.3620240-1-yangyingliang@huawei.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When creating a snapshot of a subvolume that was created in the current
transaction, we can end up not persisting a dirty extent buffer that is
referenced by the snapshot, resulting in IO errors due to checksum failures
when trying to read the extent buffer later from disk. A sequence of steps
that leads to this is the following:
1) At ioctl.c:create_subvol() we allocate an extent buffer, with logical
address 36007936, for the leaf/root of a new subvolume that has an ID
of 291. We mark the extent buffer as dirty, and at this point the
subvolume tree has a single node/leaf which is also its root (level 0);
2) We no longer commit the transaction used to create the subvolume at
create_subvol(). We used to, but that was recently removed in
commit 1b53e51a4a ("btrfs: don't commit transaction for every subvol
create");
3) The transaction used to create the subvolume has an ID of 33, so the
extent buffer 36007936 has a generation of 33;
4) Several updates happen to subvolume 291 during transaction 33, several
files created and its tree height changes from 0 to 1, so we end up with
a new root at level 1 and the extent buffer 36007936 is now a leaf of
that new root node, which is extent buffer 36048896.
The commit root remains as 36007936, since we are still at transaction
33;
5) Creation of a snapshot of subvolume 291, with an ID of 292, starts at
ioctl.c:create_snapshot(). This triggers a commit of transaction 33 and
we end up at transaction.c:create_pending_snapshot(), in the critical
section of a transaction commit.
There we COW the root of subvolume 291, which is extent buffer 36048896.
The COW operation returns extent buffer 36048896, since there's no need
to COW because the extent buffer was created in this transaction and it
was not written yet.
The we call btrfs_copy_root() against the root node 36048896. During
this operation we allocate a new extent buffer to turn into the root
node of the snapshot, copy the contents of the root node 36048896 into
this snapshot root extent buffer, set the owner to 292 (the ID of the
snapshot), etc, and then we call btrfs_inc_ref(). This will create a
delayed reference for each leaf pointed by the root node with a
reference root of 292 - this includes a reference for the leaf
36007936.
After that we set the bit BTRFS_ROOT_FORCE_COW in the root's state.
Then we call btrfs_insert_dir_item(), to create the directory entry in
in the tree of subvolume 291 that points to the snapshot. This ends up
needing to modify leaf 36007936 to insert the respective directory
items. Because the bit BTRFS_ROOT_FORCE_COW is set for the root's state,
we need to COW the leaf. We end up at btrfs_force_cow_block() and then
at update_ref_for_cow().
At update_ref_for_cow() we call btrfs_block_can_be_shared() which
returns false, despite the fact the leaf 36007936 is shared - the
subvolume's root and the snapshot's root point to that leaf. The
reason that it incorrectly returns false is because the commit root
of the subvolume is extent buffer 36007936 - it was the initial root
of the subvolume when we created it. So btrfs_block_can_be_shared()
which has the following logic:
int btrfs_block_can_be_shared(struct btrfs_root *root,
struct extent_buffer *buf)
{
if (test_bit(BTRFS_ROOT_SHAREABLE, &root->state) &&
buf != root->node && buf != root->commit_root &&
(btrfs_header_generation(buf) <=
btrfs_root_last_snapshot(&root->root_item) ||
btrfs_header_flag(buf, BTRFS_HEADER_FLAG_RELOC)))
return 1;
return 0;
}
Returns false (0) since 'buf' (extent buffer 36007936) matches the
root's commit root.
As a result, at update_ref_for_cow(), we don't check for the number
of references for extent buffer 36007936, we just assume it's not
shared and therefore that it has only 1 reference, so we set the local
variable 'refs' to 1.
Later on, in the final if-else statement at update_ref_for_cow():
static noinline int update_ref_for_cow(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
struct extent_buffer *buf,
struct extent_buffer *cow,
int *last_ref)
{
(...)
if (refs > 1) {
(...)
} else {
(...)
btrfs_clear_buffer_dirty(trans, buf);
*last_ref = 1;
}
}
So we mark the extent buffer 36007936 as not dirty, and as a result
we don't write it to disk later in the transaction commit, despite the
fact that the snapshot's root points to it.
Attempting to access the leaf or dumping the tree for example shows
that the extent buffer was not written:
$ btrfs inspect-internal dump-tree -t 292 /dev/sdb
btrfs-progs v6.2.2
file tree key (292 ROOT_ITEM 33)
node 36110336 level 1 items 2 free space 119 generation 33 owner 292
node 36110336 flags 0x1(WRITTEN) backref revision 1
checksum stored a8103e3e
checksum calced a8103e3e
fs uuid 90c9a46f-ae9f-4626-9aff-0cbf3e2e3a79
chunk uuid e8c9c885-78f4-4d31-85fe-89e5f5fd4a07
key (256 INODE_ITEM 0) block 36007936 gen 33
key (257 EXTENT_DATA 0) block 36052992 gen 33
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
total bytes 107374182400
bytes used 38572032
uuid 90c9a46f-ae9f-4626-9aff-0cbf3e2e3a79
The respective on disk region is full of zeroes as the device was
trimmed at mkfs time.
Obviously 'btrfs check' also detects and complains about this:
$ btrfs check /dev/sdb
Opening filesystem to check...
Checking filesystem on /dev/sdb
UUID: 90c9a46f-ae9f-4626-9aff-0cbf3e2e3a79
generation: 33 (33)
[1/7] checking root items
[2/7] checking extents
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
bad tree block 36007936, bytenr mismatch, want=36007936, have=0
owner ref check failed [36007936 4096]
ERROR: errors found in extent allocation tree or chunk allocation
[3/7] checking free space tree
[4/7] checking fs roots
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
checksum verify failed on 36007936 wanted 0x00000000 found 0x86005f29
bad tree block 36007936, bytenr mismatch, want=36007936, have=0
The following tree block(s) is corrupted in tree 292:
tree block bytenr: 36110336, level: 1, node key: (256, 1, 0)
root 292 root dir 256 not found
ERROR: errors found in fs roots
found 38572032 bytes used, error(s) found
total csum bytes: 16048
total tree bytes: 1265664
total fs tree bytes: 1118208
total extent tree bytes: 65536
btree space waste bytes: 562598
file data blocks allocated: 65978368
referenced 36569088
Fix this by updating btrfs_block_can_be_shared() to consider that an
extent buffer may be shared if it matches the commit root and if its
generation matches the current transaction's generation.
This can be reproduced with the following script:
$ cat test.sh
#!/bin/bash
MNT=/mnt/sdi
DEV=/dev/sdi
# Use a filesystem with a 64K node size so that we have the same node
# size on every machine regardless of its page size (on x86_64 default
# node size is 16K due to the 4K page size, while on PPC it's 64K by
# default). This way we can make sure we are able to create a btree for
# the subvolume with a height of 2.
mkfs.btrfs -f -n 64K $DEV
mount $DEV $MNT
btrfs subvolume create $MNT/subvol
# Create a few empty files on the subvolume, this bumps its btree
# height to 2 (root node at level 1 and 2 leaves).
for ((i = 1; i <= 300; i++)); do
echo -n > $MNT/subvol/file_$i
done
btrfs subvolume snapshot -r $MNT/subvol $MNT/subvol/snap
umount $DEV
btrfs check $DEV
Running it on a 6.5 kernel (or any 6.6-rc kernel at the moment):
$ ./test.sh
Create subvolume '/mnt/sdi/subvol'
Create a readonly snapshot of '/mnt/sdi/subvol' in '/mnt/sdi/subvol/snap'
Opening filesystem to check...
Checking filesystem on /dev/sdi
UUID: bbdde2ff-7d02-45ca-8a73-3c36f23755a1
[1/7] checking root items
[2/7] checking extents
parent transid verify failed on 30539776 wanted 7 found 5
parent transid verify failed on 30539776 wanted 7 found 5
parent transid verify failed on 30539776 wanted 7 found 5
Ignoring transid failure
owner ref check failed [30539776 65536]
ERROR: errors found in extent allocation tree or chunk allocation
[3/7] checking free space tree
[4/7] checking fs roots
parent transid verify failed on 30539776 wanted 7 found 5
Ignoring transid failure
Wrong key of child node/leaf, wanted: (256, 1, 0), have: (2, 132, 0)
Wrong generation of child node/leaf, wanted: 5, have: 7
root 257 root dir 256 not found
ERROR: errors found in fs roots
found 917504 bytes used, error(s) found
total csum bytes: 0
total tree bytes: 851968
total fs tree bytes: 393216
total extent tree bytes: 65536
btree space waste bytes: 736550
file data blocks allocated: 0
referenced 0
A test case for fstests will follow soon.
Fixes: 1b53e51a4a ("btrfs: don't commit transaction for every subvol create")
CC: stable@vger.kernel.org # 6.5+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Previously the duty cycle was divided equally into h_scl_l, t_scl_h.
This makes the low period of the SCL clock in Fast Mode is only 1.25us
which is way lower than the minimal value (1.3) specified in i2c
specification. In order to make sure t_scl_l, t_scl_h always fullfill
i2c specification, this commit calculates t_scl_l using this formula:
t_scl_l = clk_cycle *
((t_low_min + (scl_clock - t_low_min - t_high_min) / 2) / scl_clock)
where:
t_low_min is the minimal value of low period of the SCL clock in us;
t_high_min is the minimal value of high period of the SCL clock in us;
scl_clock is converted from SCL clock frequency into us.
Signed-off-by: Camel Guo <camel.guo@axis.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous
interfaces.
We expect ec_fw_string to be NUL-terminated based on its use with format
strings in thinkpad_acpi.c:
11241 | pr_notice("ThinkPad firmware release %s doesn't match the known patterns\n",
11242 | ec_fw_string);
Moreover, NUL-padding is not required since ec_fw_string is explicitly
zero-initialized:
11185 | char ec_fw_string[18] = {0};
When carefully copying bytes from one buffer to another in
pre-determined blocks (like what's happening here with dmi_data):
| static void find_new_ec_fwstr(const struct dmi_header *dm, void *private)
| {
| char *ec_fw_string = (char *) private;
| const char *dmi_data = (const char *)dm;
| /*
| * ThinkPad Embedded Controller Program Table on newer models
| *
| * Offset | Name | Width | Description
| * ----------------------------------------------------
| * 0x00 | Type | BYTE | 0x8C
| * 0x01 | Length | BYTE |
| * 0x02 | Handle | WORD | Varies
| * 0x04 | Signature | BYTEx6 | ASCII for "LENOVO"
| * 0x0A | OEM struct offset | BYTE | 0x0B
| * 0x0B | OEM struct number | BYTE | 0x07, for this structure
| * 0x0C | OEM struct revision | BYTE | 0x01, for this format
| * 0x0D | ECP version ID | STR ID |
| * 0x0E | ECP release date | STR ID |
| */
|
| /* Return if data structure not match */
| if (dm->type != 140 || dm->length < 0x0F ||
| memcmp(dmi_data + 4, "LENOVO", 6) != 0 ||
| dmi_data[0x0A] != 0x0B || dmi_data[0x0B] != 0x07 ||
| dmi_data[0x0C] != 0x01)
| return;
|
| /* fwstr is the first 8byte string */
| strncpy(ec_fw_string, dmi_data + 0x0F, 8);
... we shouldn't be using a C string api. Let's instead use memcpy() as
this more properly relays the intended behavior.
Do note that ec_fw_string will still end up being NUL-terminated since
we are memcpy'ing only 8 bytes into a buffer full of 18 zeroes. There's
still some trailing NUL-bytes there. To ensure this behavior, let's add
a BUILD_BUG_ON checking the length leaves space for at least one
trailing NUL-byte.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231020-strncpy-drivers-platform-x86-thinkpad_acpi-c-v1-1-312f2e33034f@google.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
These flags are not made conditional on compiler support because at the
moment exactly one version of rustc supported, and that one supports
these flags.
Building without these additional flags will manifest as objtool
printing a large number of errors about missing ENDBR and if CFI is
enabled (not currently possible) will result in incorrectly structured
function prefixes.
Signed-off-by: Matthew Maurer <mmaurer@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231009224347.2076221-1-mmaurer@google.com
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
As discussed on alsa-devel mailing list [1], it is useful to have an open
mailing list to avoid moderation delays for the kernel patch work. Use
linux-sound mailing list for kernel driver related threads.
In the first stage, change the list for the ALSA core, ASoC and tests.
[1] https://lore.kernel.org/alsa-devel/20231019-posture-cache-fe060b@meerkat/
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Acked-by: Konstantin Ryabitsev <konstantin@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231020071247.973909-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this, the newly added drivers fail to link:
aarch64-linux-ld: drivers/clk/meson/s4-pll.o: in function `meson_s4_pll_probe':
s4-pll.c:(.text+0x13c): undefined reference to `meson_clk_hw_get'
aarch64-linux-ld: drivers/clk/meson/s4-peripherals.o: in function `meson_s4_periphs_probe':
s4-peripherals.c:(.text+0xb0): undefined reference to `meson_clk_hw_get'
Fixes: e787c9c55e ("clk: meson: S4: add support for Amlogic S4 SoC PLL clock driver")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231023102810.4001943-1-arnd@kernel.org
[jbrunet: use 12 char for the Fixes as recommended ]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Finally enable independent per-DTC-domain counter allocation, except on
CMN-600 where we still need to cope with not knowing the domain topology
and thus keep counter indices sychronised across domains. This allows
users to simultaneously count up to 8 targeted events per domain, rather
than 8 globally, for up to 4x wider coverage on maximum configurations.
Even though this now looks deceptively simple, I stand by my previous
assertion that it was a flippin' nightmare to implement; all the real
head-scratchers are hidden in the foundations in the previous patch...
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/849f65566582cb102c6d0843d0f26e231180f8ac.1697824215.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The bitmap-based scheme for tracking DTC counter usage turns out to be a
complete dead-end for its imagined purpose, since by the time we have to
keep track of a per-DTC counter index anyway, we already have enough
information to make the bitmap itself redundant. Revert the remains of
it back to almost the original scheme, but now expanded to track per-DTC
indices, in preparation for making use of them in anger.
Note that since cycle count events always use a dedicated counter on a
single DTC, we reuse the field to encode their DTC index directly.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Link: https://lore.kernel.org/r/5f6ade76b47f033836d7a36c03555da896dfb4a3.1697824215.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
It transpires that dtm_unit_info is another register which got shuffled
in CMN-700 without me noticing. Fix that in a way which also proactively
fixes the fragile laziness of its consumer, just in case any further
fields ever get added alongside dtc_domain.
Fixes: 23760a0144 ("perf/arm-cmn: Add CMN-700 support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Link: https://lore.kernel.org/r/3076ee83d0554f6939fbb6ee49ab2bdb28d8c7ee.1697824215.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Add Renesas R8A779F0 in pci_device_id table so that pci-epf-test
can be used for testing PCIe EP on R-Car S4-8.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-16-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code like mode setting and retraining and
so on.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-13-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
