nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-13-miquel.raynal@bootlin.com
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Doing this in one location also saves us from dupplicating the
description of the NAND chip object.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-12-miquel.raynal@bootlin.com
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-11-miquel.raynal@bootlin.com
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Cc: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-10-miquel.raynal@bootlin.com
nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-9-miquel.raynal@bootlin.com
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-8-miquel.raynal@bootlin.com
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-7-miquel.raynal@bootlin.com
qcom,boot-partitions is a NAND chip property, not a NAND controller
property. Move the description of the property into the NAND chip
section and just enable the property in the if/else block.
Fixes: 5278cc93a9 ("dt-bindings: mtd: qcom_nandc: document qcom,boot-partitions binding")
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-6-miquel.raynal@bootlin.com
This property has been extensively used for almost two decades already,
a lot of device trees use it, this is not the preferred way to configure
the ECC engines but we cannot just ignore it. Describe the property,
list the exact strings which have once been supported and mark it
deprecated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-5-miquel.raynal@bootlin.com
The nand-ecc-placement property has been deprecated for a long time
already, it does not really mean something useful for the ECC engines
and is anyway in the vast majority of cases totally useless. Just mark
it deprecated to avoid appealing people to use it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-4-miquel.raynal@bootlin.com
In an effort to constrain as much as we can the existing binding, we
want to add "unevaluatedProperties: false" in all the NAND chip
descriptions part of NAND controller bindings. But in order to do that
properly, we also need to reference a file which contains all the
"allowed" properties. Right now this file is nand-chip.yaml but in
practice raw NAND controllers may use additional properties in their
NAND chip children node. These properties are listed under
nand-controller.yaml, which makes the "unevaluatedProperties" checks
fail while the description are valid. We need to move these NAND chip
related properties into another file, because we do not want to pollute
nand-chip.yaml which is also referenced by eg. SPI-NAND devices.
Let's create a raw-nand-chip.yaml file to reference all the properties a
raw NAND chip description can contain. The chain of inheritance becomes:
nand-controller.yaml <- raw-nand-chip.yaml
raw-nand-chip.yaml <- nand-chip.yaml
spi-nand.yaml <- nand-chip.yaml
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-3-miquel.raynal@bootlin.com
There is no addition there, but the mtd.yaml file is so generic, it can
be referenced by a wide variety of devices, including nand ones which
already define the node name to "nand@<cs>". Right now it does not lead
to any failure but when we will constrain more the schema, this will
become a problem because we want the mtd-wide properties like label or
partitions to be available for the callers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-2-miquel.raynal@bootlin.com
From time to time changes are tending to go to bitfield.h
header while it may affect other bit operataions. Add
bitfiled.h to the BITMAP API record.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
>From time to time changes are tending to go to the bits.h
headers while it may affect other bit operataions. Add
the bits.h to the BITMAP API record.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Use kernel-doc notation for the function description to prevent
a warning:
lib/cpumask.c:160: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Returns an arbitrary cpu within srcp1 & srcp2.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
The return value type is changed from 'int' to 'unsigned int' since
commit 0dfe54071d ("nodemask: Fix return values to be unsigned").
Besides, the conversion between 'int' and 'unsigned int' on the
parameter @node is guaranteed to be safe due to the limited range of
MAX_NUMNODES and CONFIG_NODES_SHIFT. By the way, '(node >= 0)' should
have been '(node) >= 0' actually.
It's unnecessary to check if their return values are greater or equal
to 0 in for_each_node_mask(). Remove it.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
bitmap_{from,to}_arr64() optimization is overly optimistic on 32-bit LE
architectures when it's wired to bitmap_copy_clear_tail().
bitmap_copy_clear_tail() takes care of unused bits in the bitmap up to
the next word boundary. But on 32-bit machines when copying bits from
bitmap to array of 64-bit words, it's expected that the unused part of
a recipient array must be cleared up to 64-bit boundary, so the last 4
bytes may stay untouched when nbits % 64 <= 32.
While the copying part of the optimization works correct, that clear-tail
trick makes corresponding tests reasonably fail:
test_bitmap: bitmap_to_arr64(nbits == 1): tail is not safely cleared: 0xa5a5a5a500000001 (must be 0x0000000000000001)
Fix it by removing bitmap_{from,to}_arr64() optimization for 32-bit LE
arches.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/20230225184702.GA3587246@roeck-us.net/
Fixes: 0a97953fd2 ("lib: add bitmap_{from,to}_arr64")
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
The tests that don't use expect_eq() macro to determine that a test is
failured must increment failed_tests explicitly.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/20230225184702.GA3587246@roeck-us.net/
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
-----BEGIN PGP SIGNATURE-----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=JwZ/
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #4
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
Just like for sc7180 devices using the Chrome bootflow (AKA trogdor
and IDP), sc7280 devices using the Chrome bootflow also need their
firmware marked dma-coherent. On sc7280 this wasn't causing WiFi to
fail to startup, since WiFi works differently there. However, on
sc7280 devices we were still getting the message at bootup after
commit 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""):
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 9c900000.memory: assign memory failed
qcom_rmtfs_mem: probe of 9c900000.memory failed with error -22
We should mark SCM properly just like we did for trogdor.
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7a1f4e7f74 ("arm64: dts: qcom: sc7280: Add basic dts/dtsi files for sc7280 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.4.I21dc14a63327bf81c6bb58fe8ed91dbdc9849ee2@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable.
Specifically, you can see in Trogdor's TF-A code [1] in
qti_sip_mem_assign() that we call qti_mmap_add_dynamic_region() with
MT_RO_DATA. This translates down to MT_MEMORY instead of
MT_NON_CACHEABLE or MT_DEVICE. Apparently Qualcomm's normal TZ
implementation maps the memory as non-cacheable.
Let's add the "dma-coherent" attribute to the SCM for trogdor.
Adding "dma-coherent" like this fixes WiFi on sc7180-trogdor
devices. WiFi was broken as of commit 7bd6680b47 ("Revert "Revert
"arm64: dma: Drop cache invalidation from
arch_dma_prep_coherent()"""). Specifically at bootup we'd get:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
From discussion on the mailing lists [2] and over IRC [3], it was
determined that we should always have been tagging the SCM as
dma-coherent on trogdor but that the old "invalidate" happened to make
things work most of the time. Tagging it properly like this is a much
more robust solution.
[1] https://chromium.googlesource.com/chromiumos/third_party/arm-trusted-firmware/+/refs/heads/firmware-trogdor-13577.B/plat/qti/common/src/qti_syscall.c
[2] https://lore.kernel.org/r/20230614165904.1.I279773c37e2c1ed8fbb622ca6d1397aea0023526@changeid
[3] https://oftc.irclog.whitequark.org/linux-msm/2023-06-15
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.3.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sc7180-idp is, for most intents and purposes, a trogdor device.
Specifically, sc7180-idp is designed to run the same style of firmware
as trogdor devices. This can be seen from the fact that IDP has the
same "Reserved memory changes" in its device tree that trogdor has.
Recently it was realized that we need to mark SCM as dma-coherent to
match what trogdor's style of firmware (based on TF-A) does [1]. That
means we need this dma-coherent tag on IDP as well.
Without this, on newer versions of Linux, specifically those with
commit 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""), WiFi will fail to
work. At bootup you'll see:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
[1] https://lore.kernel.org/r/20230615145253.1.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Fixes: 7bd6680b47 ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: f5ab220d16 ("arm64: dts: qcom: sc7180: Add remoteproc enablers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.2.I3c17d546d553378aa8a0c68c3fe04bccea7cba17@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable. Specifically,
you can see in Trogdor's TF-A code [1] in qti_sip_mem_assign() that we
call qti_mmap_add_dynamic_region() with MT_RO_DATA. This translates
down to MT_MEMORY instead of MT_NON_CACHEABLE or MT_DEVICE.
Let's allow devices like trogdor to be described properly by allowing
"dma-coherent" in the SCM node.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230616081440.v2.1.Ie79b5f0ed45739695c9970df121e11d724909157@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
CPU-A CPU-B
----- -----
ioctl(kvm_fd, KVM_SET_USER_MEMORY_REGION)
kvm_vm_ioctl_set_memory_region
kvm_set_memory_region
__kvm_set_memory_region
kvm_set_memslot(kvm, old, NULL, KVM_MR_DELETE)
kvm_invalidate_memslot
kvm_copy_memslot
kvm_replace_memslot
kvm_swap_active_memslots (A)
kvm_arch_flush_shadow_memslot (B)
same page sharing by KSM
kvm_mmu_notifier_invalidate_range_start
:
kvm_mmu_notifier_change_pte
kvm_handle_hva_range
__kvm_handle_hva_range
kvm_set_spte_gfn (C)
:
kvm_mmu_notifier_invalidate_range_end
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c718352 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35
("KVM: ARM: Memory virtualization setup").
Cc: stable@vger.kernel.org # v3.9+
Fixes: d5d8184d35 ("KVM: ARM: Memory virtualization setup")
Reported-by: Shuai Hu <hshuai@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Message-Id: <20230615054259.14911-1-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 36de5f303c.
The commit caused boot failures on some configurations due to cgroup
hierarchies not being created at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
ice_change_mtu() is currently using a separate ice_down() and ice_up()
calls to reflect changed MTU. ice_down_up() serves this purpose, so do
the refactoring here.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is no need to use managed memory allocation here. The memory is
released at the end of the function.
Use kzalloc()/kfree() to simplify the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The complete profile bit together with the NSTR link pair
present bit indicate whether or not the NSTR bitmap is,
the NSTR bitmap size just indicates how big it is.
Fixes: 7b6f08771b ("wifi: ieee80211: Support validating ML station profile length")
Fixes: 5c1f97537b ("wifi: mac80211: store BSS param change count from assoc response")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BTF_TYPE_SAFE_NESTED macro was replaced by the BTF_TYPE_SAFE_TRUSTED,
BTF_TYPE_SAFE_RCU, and BTF_TYPE_SAFE_RCU_OR_NULL macros. Fix the docs
correspondingly.
Fixes: 6fcd486b3a ("bpf: Refactor RCU enforcement in the verifier.")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230622095424.1024244-1-aspsk@isovalent.com
Fix the description of the seq_info field of the bpf_iter_reg structure which
was wrong due to an accidental copy/paste of the previous field's description.
Fixes: 8972e18a43 ("bpf, docs: BPF Iterator Document")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230622095407.1024053-1-aspsk@isovalent.com
According to ADI, changing PMON_CONFIG while the ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after. Follow ADI
recommendation and disable ADC while PMON_CONFIG is updated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-3-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to ADI, changing PMON_CONFIG while ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after.
To prepare for this change, rename adm1275_read_pmon_config()
and adm1275_write_pmon_config() to adm1275_read_samples() and
adm1275_write_samples() to more accurately reflect the functionality
of the code. Introduce new function adm1275_write_pmon_config()
and use it for all code writing into the PMON_CONFIG register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The commit 0cac21b02b ("riscv: use 16KB kernel stack on 64-bit")
increases the thread size mandatory, but some scenarios, such as D1 with
a small memory footprint, would suffer from that. After independent irq
stack support, let's give users a choice to determine their custom stack
size.
Link: https://lore.kernel.org/linux-riscv/5f6e6c39-b846-4392-b468-02202404de28@www.fastmail.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230614013018.2168426-4-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the HAVE_SOFTIRQ_ON_OWN_STACK feature for the IRQ_STACKS config, and
the irq and softirq use the same irq_stack of percpu.
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230614013018.2168426-3-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Fix the following fallthrough warnings seen after building sh
architecture with sh7763rdp_defconfig configuration:
drivers/video/fbdev/sh7760fb.c: In function 'sh7760fb_get_color_info':
drivers/video/fbdev/sh7760fb.c:138:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
138 | lgray = 1;
| ~~~~~~^~~
drivers/video/fbdev/sh7760fb.c:139:9: note: here
139 | case LDDFR_4BPP:
| ^~~~
drivers/video/fbdev/sh7760fb.c:143:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
143 | lgray = 1;
| ~~~~~~^~~
drivers/video/fbdev/sh7760fb.c:144:9: note: here
144 | case LDDFR_8BPP:
| ^~~~
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
When configurating a CHn Source Image Format Register (LDBBSIFR), one
should use the corresponding LDBBSIFR_RPKF_* definition for overlay
planes, not the DDFR_PKF_* definition for the primary plane.
Fortunately both definitions resolve to the same value, so this bug did
not cause any harm.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Helge Deller <deller@gmx.de>
We all know they are redundant.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The check for existing VFs was redundant since very
inception of SR-IOV sysfs interface in the kernel,
see commit 1789382a72 ("PCI: SRIOV control and status via sysfs").
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice driver's .ndo_bpf callback brings interface down and up
independently of XDP resources' presence. This is only needed when
either these resources have to be configured or removed. It means that
if one is switching XDP programs on-the-fly with running traffic,
packets will be dropped.
To avoid this, compare early on ice_xdp_setup_prog() state of incoming
bpf_prog pointer vs the bpf_prog pointer that is already assigned to
VSI. Do the swap in case VSI has bpf_prog and incoming one are non-NULL.
Lastly, while at it, put old bpf_prog *after* the update of Rx ring's
bpf_prog pointer. In theory previous code could expose us to a state
where Rx ring's bpf_prog would still be referring to old_prog that got
released with earlier bpf_prog_put().
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_sq_send_cmd() function is used to send messages to the control
queues used to communicate with firmware, virtual functions, and even some
hardware.
When sending a control queue message, the driver is designed to
synchronously wait for a response from the queue. Currently it waits
between checks for 100 to 150 microseconds.
Commit f86d6f9c49 ("ice: sleep, don't busy-wait, for
ICE_CTL_Q_SQ_CMD_TIMEOUT") did recently change the behavior from an
unnecessary delay into a sleep which is a significant improvement over the
old behavior of polling using udelay.
Because of the nature of PCIe transactions, the hardware won't be informed
about a new message until the write to the tail register posts. This is
only guaranteed to occur at the next register read. In ice_sq_send_cmd(),
this happens at the ice_sq_done() call. Because of this, the driver
essentially forces a minimum of one full wait time regardless of how fast
the response is.
For the hardware-based sideband queue, this is especially slow. It is
expected that the hardware will respond within 2 or 3 microseconds, an
order of magnitude faster than the 100-150 microsecond sleep.
Allow such fast completions to occur without delay by introducing a small 5
microsecond delay first before entering the sleeping timeout loop. Ensure
the tail write has been posted by using ice_flush(hw) first.
While at it, lets also remove the ICE_CTL_Q_SQ_CMD_USEC macro as it
obscures the sleep time in the inner loop. It was likely introduced to
avoid "magic numbers", but in practice sleep and delay values are easier to
read and understand when using actual numbers instead of a named constant.
This change should allow the fast hardware based control queue messages to
complete quickly without delay, while slower firmware queue response times
will sleep while waiting for the response.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
KVM_ARM_VCPU_POWER_OFF is as bit index, _not_ a literal bitmask.
Nonetheless, commit e3c1c0cae3 ("KVM: arm64: Relax invariance
of KVM_ARM_VCPU_POWER_OFF") started using it that way, meaning that
powering off a vCPU with the KVM_ARM_VCPU_INIT ioctl is completely
broken.
Fix it by using a shifted bit for the bitwise operations instead.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: e3c1c0cae3 ("KVM: arm64: Relax invariance of KVM_ARM_VCPU_POWER_OFF")
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230622160922.1925530-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
STM32F4-F7 are, from hardware point of view, capable to handle device mode.
So this property should not be forced at false in dt-bindings.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/Message-Id: <20230621115523.923176-3-valentin.caron@foss.st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the soundcard does not specify the dapm pins, let the common
code add these pins for jack.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/Message-Id: <20230302120327.10823-1-srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver uses the mapped __iomem address of the FIFO as the DMA
address for the device. This apparently works on loongarch because of
the way it handles __iomem pointers as aliases of physical addresses,
but this is not portable to other architectures and causes a compiler
warning when dma addresses are not the same size as pointers:
sound/soc/loongson/loongson_i2s_pci.c: In function 'loongson_i2s_pci_probe':
sound/soc/loongson/loongson_i2s_pci.c:110:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
110 | tx_data->dev_addr = (dma_addr_t)i2s->reg_base + LS_I2S_TX_DATA;
| ^
sound/soc/loongson/loongson_i2s_pci.c:113:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
113 | rx_data->dev_addr = (dma_addr_t)i2s->reg_base + LS_I2S_RX_DATA;
| ^
Change the driver to instead use the physical address as stored in the
PCI BAR resource directly. Since 'dev_addr' is a 32-bit address, I think
this results in the same truncated address on loongarch but is otherwise
closer to portable code and avoids the warning.
Fixes: d84881e068 ("ASoC: Add support for Loongson I2S controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/Message-Id: <20230622101235.3230941-1-arnd@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
"enum" values should be integers or strings, not arrays (though json-schema
does allow arrays, we do not). In this case, all possible combinations are
allowed anyways, so there's little point in expressing as an array.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230621231044.3816914-1-robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove stale comments in AHUB driver which is related to DAPM
widgets and routes. This is misleading otherwise.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/Message-Id: <1687433656-7892-7-git-send-email-spujar@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Align with other AHUB module drivers and use normal system
sleep for ASRC as well.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/Message-Id: <1687433656-7892-6-git-send-email-spujar@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
