devm_clk_notifier_register() allocates a devres resource for clk
notifier but didn't register that to the device, so the notifier didn't
get unregistered on device detach and the allocated resource was leaked.
Fix the issue by registering the resource through devres_add().
This issue was found with kmemleak on a Chromebook.
Fixes: 6d30d50d03 ("clk: add devm variant of clk_notifier_register")
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://lore.kernel.org/r/20230619112253.v2.1.I13f060c10549ef181603e921291bdea95f83033c@changeid
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The new phy driver attempts to select a driver from another subsystem,
but that fails when the NVMEM subsystem is disabled:
WARNING: unmet direct dependencies detected for NVMEM_MTK_EFUSE
Depends on [n]: NVMEM [=n] && (ARCH_MEDIATEK [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Selected by [y]:
- MEDIATEK_GE_SOC_PHY [=y] && NETDEVICES [=y] && PHYLIB [=y] && (ARM64 && ARCH_MEDIATEK [=n] || COMPILE_TEST [=y])
I could not see an actual compile time dependency, so presumably this
is only needed for for working correctly but not technically a dependency
on that particular nvmem driver implementation, so it would likely
be safe to remove the select for compile testing.
To keep the spirit of the original 'select', just replace this with a
'depends on' that ensures that the driver will work but does not get in
the way of build testing.
Fixes: 98c485eaf5 ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230616093009.3511692-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rework iterating over DT CPU nodes to iterate over possible CPUs
instead. There's no need to walk the DT CPU nodes again. Possible CPUs
is equal to the number of CPUs defined in the DT. Using the "reg" value
for an array index is fragile as it assumes "reg" is 0-N which often is
not the case.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230327-mvebu-clk-fixes-v2-3-8333729ee45d@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use of_get_cpu_hwid() rather than the open coded reading of the CPU
nodes "reg" property. The existing code is in fact wrong as the "reg"
address cells size is 2 cells for arm64. The existing code happens to
work because the DTS files are wrong as well.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230327-mvebu-clk-fixes-v2-2-8333729ee45d@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
drivers/clk/mvebu/ is missing a maintainers entry. Add it to the
existing entry for the Marvell mvebu platforms.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230327-mvebu-clk-fixes-v2-1-8333729ee45d@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In the function bdev_add_partition(),there is no check that the start
and end sectors exceed the size of the disk before calling add_partition.
When we call the block's ioctl interface directly to add a partition,
and the capacity of the disk is set to 0 by driver,the command will
continue to execute.
Signed-off-by: Min Li <min15.li@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230619091214.31615-1-min15.li@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEE6fsu8pdIjtWE/DpLiiy9cAdyT1EFAmSNFQcACgkQiiy9cAdy
T1F/0gwAs396WKBsx5fEiHPucWOdBemT/IqSW+ZTY5LNwB6A4B71W7D8w5by/0MU
bXprt3XJuPnb21euW2L8BlGg9jJyd3GBcJWv4/GbOzQ//ZMkyT50sZbrWSDP2luq
jELbe+CS+xOimOSBnIEDxYWqWxetTfDUwlbUHTrHaMGCCZcRJZmEXsJEGelSUx4+
uipbj0sMUB3x4H7MyEND0bbGxhMKzZXsymRvKTsS3aR1qTioQ8FoNrmDlUBCgN4u
qbEsG7GGQTj/WrdUrzbQ9DkZa17C+2PNV/j1xKGu/9hBpr2lZSyNmj46MqmPegKD
4lPwG0GmWEXWuRP7QCXNzS9p9Rkms2C1MnPH7x2NqzoOXsJSZFb4j/fp0oKG4mu1
zoIjZ5cA+wsOxoJTyOHNdWYFzBcPnUIQ5ZP6696alejA9TtdxqrQdhEBNO9YnsCP
xreIMADWX8pIjcdDx6DSQ8ZzhyB5Uu46j0K1Ve1e/58HX8FhGrBcOQGFexIXjuMa
8655VONz
=yfOS
-----END PGP SIGNATURE-----
Merge tag '6.4-rc6-smb3-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Four smb3 server fixes, all also for stable:
- fix potential oops in parsing compounded requests
- fix various paths (mkdir, create etc) where mnt_want_write was not
checked first
- fix slab out of bounds in check_message and write"
* tag '6.4-rc6-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: validate session id and tree id in the compound request
ksmbd: fix out-of-bound read in smb2_write
ksmbd: add mnt_want_write to ksmbd vfs functions
ksmbd: validate command payload size
Allow of unprivileged Persistent Reservation operations on devices
if the write permission check on the device node has passed.
brw-rw---- 1 root disk 259, 0 Jun 13 07:09 /dev/nvme0n1
In the example above, the "disk" group of nvme0n1 is also allowed to
make reservations on the device even without CAP_SYS_ADMIN.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230613084008.93795-3-jefflexu@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Refuse Persistent Reservation operations on partitions as reservation
on partitions doesn't make sense.
Besides, introduce blkdev_pr_allowed() helper, where more policies could
be placed here later.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230613084008.93795-2-jefflexu@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The device /dev/hwctr was introduced to access complete
CPU Measurement facility counter sets via an ioctl system call.
The access the to device is limited to privileged processes
running as root or superuser. The capability CAP_SYS_ADMIN
is required. The device permissions are read/write for the
device owner root. There is no need for this restriction.
Make the device access permission read/write for all and
reduce the capabilities to CAP_PERFMON.
Any user space program with the CAP_PERFMON capability assigned to it
can now read and display the CPU Measurement facility counter sets.
For more details on perf tool usage and security, see linux
documentation in Documentation/admin-guide/perf-security.rst.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
During module load, module layout allocation occurs by initially
allowing the architecture to frob the sections. This is performed via
module_frob_arch_sections().
However, the size of each module memory types like text,data,rodata etc
are updated correctly only after layout_sections().
After calculation of required module memory sizes for each types,
move_module() is responsible for allocating the module memory for each
type from modules vaddr range.
Considering the sequence above, module_frob_arch_sections() updates the
module mod_arch_specific got_offset before module memory text type size
is fully updated in layout_sections(). Hence mod_arch_specific
got_offset points to currently zero.
As per s390 ABI,
R_390_GOTENT : (G + O + A - P) >> 1
where
G=me->mem[MOD_TEXT].base+me->arch.got_offset
O=info->got_offset
A=rela->r_addend
P=loc
fix R_390_GOTENT calculation in apply_rela().
Note: currently this doesn't break anything because me->arch.got_offset
is zero. However, reordering of functions in the future could break it.
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Kernel Address Sanitizer uses 3 bits per byte to
encode memory. That is the number of bits the start
and end address of a memory range is shifted right
when the corresponding shadow memory is created for
that memory range.
The used memory mapping routine expects page-aligned
addresses, while the above described 3-bit shift might
turn the shadow memory range start and end boundaries
into non-page-aligned in case the size of the original
memory range is less than (PAGE_SIZE << 3). As result,
the resulting shadow memory range could be short on one
page.
Align on page boundary the start and end addresses when
mapping a shadow memory range and avoid the described
issue in the future.
Note, that does not fix a real problem, since currently
no virtual regions of size less than (PAGE_SIZE << 3)
exist.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Since commit 3b5c3f000c2e ("s390/kasan: move shadow mapping
to decompressor") the decompressor establishes mappings for
the shadow memory and sets initial protection attributes to
RWX. The decompressed kernel resets protection to RW+NX
later on.
In case a shadow memory range is not aligned on page boundary
(e.g. as result of mem= kernel command line parameter use),
the "Checked W+X mappings: FAILED, 1 W+X pages found" warning
hits.
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Fixes: 557b19709d ("s390/kasan: move shadow mapping to decompressor")
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
intel_gsc_uc_fw_proxy_init_done is used by a few code paths
and usages. However, certain paths need a wakeref while others
can't take a wakeref such as from the runtime_pm_resume callstack.
Add a param into this helper to allow callers to direct whether
to take the wakeref or not. This resolves the following bug:
INFO: task sh:2607 blocked for more than 61 seconds.
Not tainted 6.3.0-pxp-gsc-final-jun14+ #297
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:sh state:D stack:13016 pid:2607 ppid:2602 flags:0x00004000
Call Trace:
<TASK>
__schedule+0x47b/0xe10
schedule+0x58/0xd0
rpm_resume+0x1cc/0x800
? __pfx_autoremove_wake_function+0x10/0x10
__pm_runtime_resume+0x42/0x80
__intel_runtime_pm_get+0x19/0x80 [i915]
gsc_uc_get_fw_status+0x10/0x50 [i915]
intel_gsc_uc_fw_init_done+0x9/0x20 [i915]
intel_gsc_uc_load_start+0x5b/0x130 [i915]
__uc_resume+0xa5/0x280 [i915]
intel_runtime_resume+0xd4/0x250 [i915]
? __pfx_pci_pm_runtime_resume+0x10/0x10
__rpm_callback+0x3c/0x160
Fixes: 8c33c3755b ("drm/i915/gsc: take a wakeref for the proxy-init-completion check")
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230615211940.4061378-1-alan.previn.teres.alexis@intel.com
In jfs_dmap.c at line 381, BLKTODMAP is used to get a logical block
number inside dbFree(). db_l2nbperpage, which is the log2 number of
blocks per page, is passed as an argument to BLKTODMAP which uses it
for shifting.
Syzbot reported a shift out-of-bounds crash because db_l2nbperpage is
too big. This happens because the large value is set without any
validation in dbMount() at line 181.
Thus, make sure that db_l2nbperpage is correct while mounting.
Max number of blocks per page = Page size / Min block size
=> log2(Max num_block per page) = log2(Page size / Min block size)
= log2(Page size) - log2(Min block size)
=> Max db_l2nbperpage = L2PSIZE - L2MINBLOCKSIZE
Reported-and-tested-by: syzbot+d2cd27dcf8e04b232eb2@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?id=2a70a453331db32ed491f5cbb07e81bf2d225715
Cc: stable@vger.kernel.org
Suggested-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
[BUG]
David reported an ASSERT() get triggered during fio load on 8 devices
with data/raid6 and metadata/raid1c3:
fio --rw=randrw --randrepeat=1 --size=3000m \
--bsrange=512b-64k --bs_unaligned \
--ioengine=libaio --fsync=1024 \
--name=job0 --name=job1 \
The ASSERT() is from rbio_add_bio() of raid56.c:
ASSERT(orig_logical >= full_stripe_start &&
orig_logical + orig_len <= full_stripe_start +
rbio->nr_data * BTRFS_STRIPE_LEN);
Which is checking if the target rbio is crossing the full stripe
boundary.
[100.789] assertion failed: orig_logical >= full_stripe_start && orig_logical + orig_len <= full_stripe_start + rbio->nr_data * BTRFS_STRIPE_LEN, in fs/btrfs/raid56.c:1622
[100.795] ------------[ cut here ]------------
[100.796] kernel BUG at fs/btrfs/raid56.c:1622!
[100.797] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[100.798] CPU: 1 PID: 100 Comm: kworker/u8:4 Not tainted 6.4.0-rc6-default+ #124
[100.799] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552-rebuilt.opensuse.org 04/01/2014
[100.802] Workqueue: writeback wb_workfn (flush-btrfs-1)
[100.803] RIP: 0010:rbio_add_bio+0x204/0x210 [btrfs]
[100.806] RSP: 0018:ffff888104a8f300 EFLAGS: 00010246
[100.808] RAX: 00000000000000a1 RBX: ffff8881075907e0 RCX: ffffed1020951e01
[100.809] RDX: 0000000000000000 RSI: 0000000000000008 RDI: 0000000000000001
[100.811] RBP: 0000000141d20000 R08: 0000000000000001 R09: ffff888104a8f04f
[100.813] R10: ffffed1020951e09 R11: 0000000000000003 R12: ffff88810e87f400
[100.815] R13: 0000000041d20000 R14: 0000000144529000 R15: ffff888101524000
[100.817] FS: 0000000000000000(0000) GS:ffff88811ac00000(0000) knlGS:0000000000000000
[100.821] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[100.822] CR2: 000055d54e44c270 CR3: 000000010a9a1006 CR4: 00000000003706a0
[100.824] Call Trace:
[100.825] <TASK>
[100.825] ? die+0x32/0x80
[100.826] ? do_trap+0x12d/0x160
[100.827] ? rbio_add_bio+0x204/0x210 [btrfs]
[100.827] ? rbio_add_bio+0x204/0x210 [btrfs]
[100.829] ? do_error_trap+0x90/0x130
[100.830] ? rbio_add_bio+0x204/0x210 [btrfs]
[100.831] ? handle_invalid_op+0x2c/0x30
[100.833] ? rbio_add_bio+0x204/0x210 [btrfs]
[100.835] ? exc_invalid_op+0x29/0x40
[100.836] ? asm_exc_invalid_op+0x16/0x20
[100.837] ? rbio_add_bio+0x204/0x210 [btrfs]
[100.837] raid56_parity_write+0x64/0x270 [btrfs]
[100.838] btrfs_submit_chunk+0x26e/0x800 [btrfs]
[100.840] ? btrfs_bio_init+0x80/0x80 [btrfs]
[100.841] ? release_pages+0x503/0x6d0
[100.842] ? folio_unlock+0x2f/0x60
[100.844] ? __folio_put+0x60/0x60
[100.845] ? btrfs_do_readpage+0xae0/0xae0 [btrfs]
[100.847] btrfs_submit_bio+0x21/0x60 [btrfs]
[100.847] submit_one_bio+0x6a/0xb0 [btrfs]
[100.849] extent_write_cache_pages+0x395/0x680 [btrfs]
[100.850] ? __extent_writepage+0x520/0x520 [btrfs]
[100.851] ? mark_usage+0x190/0x190
[100.852] extent_writepages+0xdb/0x130 [btrfs]
[100.853] ? extent_write_locked_range+0x480/0x480 [btrfs]
[100.854] ? mark_usage+0x190/0x190
[100.854] ? attach_extent_buffer_page+0x220/0x220 [btrfs]
[100.855] ? reacquire_held_locks+0x178/0x280
[100.856] ? writeback_sb_inodes+0x245/0x7f0
[100.857] do_writepages+0x102/0x2e0
[100.858] ? page_writeback_cpu_online+0x10/0x10
[100.859] ? __lock_release.isra.0+0x14a/0x4d0
[100.860] ? reacquire_held_locks+0x280/0x280
[100.861] ? __lock_acquired+0x1e9/0x3d0
[100.862] ? do_raw_spin_lock+0x1b0/0x1b0
[100.863] __writeback_single_inode+0x94/0x450
[100.864] writeback_sb_inodes+0x372/0x7f0
[100.864] ? lock_sync+0xd0/0xd0
[100.865] ? do_raw_spin_unlock+0x93/0xf0
[100.866] ? sync_inode_metadata+0xc0/0xc0
[100.867] ? rwsem_optimistic_spin+0x340/0x340
[100.868] __writeback_inodes_wb+0x70/0x130
[100.869] wb_writeback+0x2d1/0x530
[100.869] ? __writeback_inodes_wb+0x130/0x130
[100.870] ? lockdep_hardirqs_on_prepare.part.0+0xf1/0x1c0
[100.870] wb_do_writeback+0x3eb/0x480
[100.871] ? wb_writeback+0x530/0x530
[100.871] ? mark_lock_irq+0xcd0/0xcd0
[100.872] wb_workfn+0xe0/0x3f0<
[CAUSE]
Commit a97699d1d6 ("btrfs: replace map_lookup->stripe_len by
BTRFS_STRIPE_LEN") changes how we calculate the map length, to reduce
u64 division.
Function btrfs_max_io_len() is to get the length to the stripe boundary.
It calculates the full stripe start offset (inside the chunk) by the
following code:
*full_stripe_start =
rounddown(*stripe_nr, nr_data_stripes(map)) <<
BTRFS_STRIPE_LEN_SHIFT;
The calculation itself is fine, but the value returned by rounddown() is
dependent on both @stripe_nr (which is u32) and nr_data_stripes() (which
returned int).
Thus the result is also u32, then we do the left shift, which can
overflow u32.
If such overflow happens, @full_stripe_start will be a value way smaller
than @offset, causing later "full_stripe_len - (offset -
*full_stripe_start)" to underflow, thus make later length calculation to
have no stripe boundary limit, resulting a write bio to exceed stripe
boundary.
There are some other locations like this, with a u32 @stripe_nr got left
shift, which can lead to a similar overflow.
[FIX]
Fix all @stripe_nr with left shift with a type cast to u64 before the
left shift.
Those involved @stripe_nr or similar variables are recording the stripe
number inside the chunk, which is small enough to be contained by u32,
but their offset inside the chunk can not fit into u32.
Thus for those specific left shifts, a type cast to u64 is necessary so
this patch does not touch them and the code will be cleaned up in the
future to keep the fix minimal.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: a97699d1d6 ("btrfs: replace map_lookup->stripe_len by BTRFS_STRIPE_LEN")
Tested-by: David Sterba <dsterba@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Make HSW/BDW use port_mask for output probing as well.
To achieve that the strap checks are moved into
intel_ddi_init() itself. Or should we move them to the
runtime port_mask init instead? Maybe not since the hardware
is still there, just not connected to anything.
v2: Account for DDI-E in strap detection
Keep to the old CRT->DDI init order
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-8-ville.syrjala@linux.intel.com
Instead of listing every platform's possible DDI outputs
in intel_setup_outputs() just loop over the new port_mask
to achieve the same thing.
HSW/BDW were left as is since they still look at the straps
as well.
DSI is still a mess. For now just check for the relevant
platforms explicitly.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-7-ville.syrjala@linux.intel.com
The SDVO code already warns when the port in question doesn't
actually support SDVO. Let's make that also bail the encoder
registration like the generic assert_port_valid() we added.
And add a similar thing for g4x HDMI, mainly because on g4x
itsefl port D only supports DP but not SDVO/HDMI. For the
other platforms the generic port_mask check should actually
be sufficient, but since we're here might as well list the
ports.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-6-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
Sprinkle in some BUILD_BUG_ON()s to make sure some of
the bitmasks used in the device info have enough bits.
Do we have a better place for this sort of stuff?
v2: Relocate to the new place
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-4-ville.syrjala@linux.intel.com
Declare the available DVO/SDVO/HDMI/DP/DDI ports in the
device info. The other outputs (LVDS/TV/DSI/VGA) are left
out since for most of them we don't consider them as "ports".
DSI we should probably perhaps include somehow in the device
info. Just not sure how. Or we just introduce a HAS_DSI() and
call it a day?
TODO: figure out what to do about the subplatform stuff. Would
it be better to declare those directly with a different
device info or not? Also not sure the icl port-f stuff
matters even. Bspec claims there are icl SKUs with far
less ports than that and we don't seem to check for those
either?
v2: Fix TC5 vs. TC6 mixup on TGL (Jani)
Drop DDI C for now on TGL, and add a FIXME (Jani)
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-3-ville.syrjala@linux.intel.com
scall is a deprecated alias for ecall. ecall is used in several places,
so there is no assembler compatibility concern.
Signed-off-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20230423223210.126948-1-maskray@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Request failed link recovery with any upstream PCIe bridge where a device
has not come back after reset within PCI_RESET_WAIT time. Reset the
polling interval if recovery succeeded, otherwise continue as usual.
[bhelgaas: inline pcie_parent_link_retrain()]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306111631050.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Attempt to handle cases such as with a downstream port of the ASMedia
ASM2824 PCIe switch where link training never completes and the link
continues switching between speeds indefinitely with the data link layer
never reaching the active state.
It has been observed with a downstream port of the ASMedia ASM2824 Gen 3
switch wired to the upstream port of the Pericom PI7C9X2G304 Gen 2 switch,
using a Delock Riser Card PCI Express x1 > 2 x PCIe x1 device, P/N 41433,
wired to a SiFive HiFive Unmatched board. In this setup the switches
should negotiate a link speed of 5.0GT/s, falling back to 2.5GT/s if
necessary.
Instead the link continues oscillating between the two speeds, at the rate
of 34-35 times per second, with link training reported repeatedly active
~84% of the time. Limiting the target link speed to 2.5GT/s with the
upstream ASM2824 device makes the two switches communicate correctly.
Removing the speed restriction afterwards makes the two devices switch to
5.0GT/s then.
Make use of these observations and detect the inability to train the link
by checking for the Data Link Layer Link Active status bit being off while
the Link Bandwidth Management Status indicating that hardware has changed
the link speed or width in an attempt to correct unreliable link operation.
Restrict the speed to 2.5GT/s then with the Target Link Speed field,
request a retrain and wait 200ms for the data link to go up. If this is
successful, lift the restriction, letting the devices negotiate a higher
speed.
Also check for a 2.5GT/s speed restriction the firmware may have already
arranged and lift it too with ports of devices known to continue working
afterwards (currently only ASM2824), that already report their data link
being up.
[bhelgaas: reorder and squash stubs from
https://lore.kernel.org/r/alpine.DEB.2.21.2306111619570.64925@angie.orcam.me.uk
to avoid adding stubs that do nothing]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203022037020.56670@angie.orcam.me.uk/
Link: a398a51ccc
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2305310038540.59226@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove a DLLLA status bit polling loop from pcie_wait_for_link_delay() and
call almost identical code in pcie_wait_for_link_status() instead. This
reduces the lower bound on the polling interval from 10ms to 1ms, possibly
increasing the CPU load on the system in favour to reducing the wait time.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306111611170.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Let the caller of pcie_retrain_link() specify whether they want to use the
LT bit or the DLLLA bit of the Link Status Register to determine if link
training has completed. It is up to the caller to verify whether the use
of the DLLLA bit, the implementation of which is optional, is valid for the
device requested.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110310540.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export pcie_retrain_link() for link retrain needs outside ASPM. Struct
pcie_link_state is local to ASPM and only used by pcie_retrain_link() to
get at the associated PCI device, so change the operand and adjust the lone
call site accordingly. Document the interface. No functional change at
this point.
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306110229010.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert LINK_RETRAIN_TIMEOUT from jiffies to milliseconds, accordingly
rename to PCIE_LINK_RETRAIN_TIMEOUT_MS, and make available via "pci.h" for
the PCI core to use. Use in pcie_wait_for_link_delay().
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2305310030280.59226@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make quirk_enable_clear_retrain_link() an early quirk so that any later
fixups can rely on dev->clear_retrain_link to have been already
initialised.
[bhelgaas: reorder to just before it becomes possible to call
pcie_retrain_link() earlier]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2305310049000.59226@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move code polling for the Link Training bit to clear into a function of its
own.
[bhelgaas: reorder to clean up before exposing to PCI core]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2306111605060.64925@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call netdev_{put, hold} of dev_{put, hold} will check NULL, so there
is no need to check before using dev_{put, hold}, remove it to silence the
warning:
./drivers/infiniband/core/cma.c:4812:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Link: https://lore.kernel.org/r/20230614014328.14007-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5521
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The flags parameter to the request notify verb is a bitmask. But, rxe
driver treats cq->notify as an int. If someone ever set both the
IB_CQ_SOLICITED and the IB_CQ_NEXT_COMP bits rxe_cq_post could fail to
generate a completion event. This patch treats the notify flags as a bit
mask consistently and can handle the above case correctly.
Link: https://lore.kernel.org/r/20230612162244.20038-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Remove all the open coded magic on slot->file_ptr by introducing two
helpers that return the file pointer and the flags instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620113235.920399-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Two of the three callers want them, so return the more usual format,
and shift into the FFS_ form only for the fixed file table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620113235.920399-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SCM inflight mechanism has nothing to do with the fact that a file
might be a regular file or not and if it supports non-blocking
operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620113235.920399-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that this only checks O_NONBLOCK and FMODE_NOWAIT, the helper is
complete overkilļ, and the comments are confusing bordering to wrong.
Just inline the check into the caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620113235.920399-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sort() in Linux is based on heapsort which is not a stable sort
algorithm - equal elements are being reordered. For reserved memory in
the device tree this happens mainly for dynamic allocations: They do not
have an address to sort with, so they are reordered somewhat randomly
when adding/removing other unrelated reserved memory nodes.
Functionally this is not a big problem, but it's confusing during
development when all the addresses change after adding unrelated
reserved memory nodes.
Make the order stable by sorting dynamic allocations according to
the node order in the device tree. Static allocations are not affected
by this because they are still sorted by their (fixed) address.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230510-dt-resv-bottom-up-v2-2-aeb2afc8ac25@gerhold.net
Signed-off-by: Rob Herring <robh@kernel.org>
Right now dynamic reserved memory regions are allocated either
bottom-up or top-down, depending on the memblock setting of the
architecture. This is fine when the address is arbitrary. However,
when using "alloc-ranges" the regions are often placed somewhere
in the middle of (free) RAM, even if the range starts or ends next
to another (static) reservation.
Try to detect this situation, and choose explicitly between bottom-up
or top-down to allocate the memory close to the other reservations:
1. If the "alloc-range" starts at the end or inside an existing
reservation, use bottom-up.
2. If the "alloc-range" ends at the start or inside an existing
reservation, use top-down.
3. If both or none is the case, keep the current
(architecture-specific) behavior.
There are plenty of edge cases where only a more complex algorithm
would help, but even this simple approach helps in many cases to keep
the reserved memory (and therefore also the free memory) contiguous.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230510-dt-resv-bottom-up-v2-1-aeb2afc8ac25@gerhold.net
Signed-off-by: Rob Herring <robh@kernel.org>
Amir has implemented lots of features in overlayfs and is very active in
maintenance.
Make this official in the MAINTAINERS file.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
