When we split a pmd into ptes, pmd_present() and pmd_trans_huge() should
return true, otherwise it would be treated as a swap pmd.
This is the same as arm64 does in commit b65399f611 ("arm64/mm: Change
THP helpers to comply with generic MM semantics"), we also add a new bit
named _PAGE_PRESENT_INVALID for LoongArch.
Signed-off-by: Hongchen Zhang <zhanghongchen@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Issue found by Coverity.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613170907.2413559-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mingshuai Ren reports:
When a new chain is added by using tc, one soft lockup alarm will be
generated after delete the prio 0 filter of the chain. To reproduce
the problem, perform the following steps:
(1) tc qdisc add dev eth0 root handle 1: htb default 1
(2) tc chain add dev eth0
(3) tc filter del dev eth0 chain 0 parent 1: prio 0
(4) tc filter add dev eth0 chain 0 parent 1:
Fix the issue by accounting for additional reference to chains that are
explicitly created by RTM_NEWCHAIN message as opposed to implicitly by
RTM_NEWTFILTER message.
Fixes: 726d061286 ("net: sched: prevent insertion of new classifiers during chain flush")
Reported-by: Mingshuai Ren <renmingshuai@huawei.com>
Closes: https://lore.kernel.org/lkml/87legswvi3.fsf@nvidia.com/T/
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20230612093426.2867183-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devicetree bindings for AM62x based phyCORE-AM62 SoM
and phyBOARD-Lyra RDK.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230504140143.1425951-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Define the wakeup uart pin-mux for completeness and add explicit
muxing for mcu_uart0. This allows the device tree usage in bootloader
and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Define the wakeup uart pin-mux for completeness and add explicit
muxing for mcu_uart0. This allows the device tree usage in bootloader
and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add pinmux required to bring out the i2c and gpios on 40-pin RPi
expansion header on the AM68 SK board.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
regions, accordingly split the existing wkup_pmx region as follows to avoid
the non-addressable regions and include the rest of valid WKUP_PADCONFIG
registers. Also update references to old nodes with new ones.
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
Fixes: b8545f9d3a ("arm64: dts: ti: Add initial support for J721S2 SoC")
Cc: <stable@vger.kernel.org> # 6.3
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602153554.1571128-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-06-12 (igc, igb)
This series contains updates to igc and igb drivers.
Husaini clears Tx rings when interface is brought down for igc.
Vinicius disables PTM and PCI busmaster when removing igc driver.
Alex adds error check and path for NVM read error on igb.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igb: fix nvm.ops.read() error handling
igc: Fix possible system crash when loading module
igc: Clean the TX buffer and TX descriptor ring
====================
Link: https://lore.kernel.org/r/20230612205208.115292-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aiases are defined at board level, so dropping from soc level
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230611111140.3189111-7-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
main_i2c0 pin mux was duplicated in som and common file.
So removing duplicated node from common file.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230611111140.3189111-4-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control
Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN
input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit
muxes the previous timer output, or possibly and external TIMER_IO pad
source, to the input clock of the selected timer instance for odd numered
timers. For the even numbered timers, the CASCADE_EN bit does not do
anything. The timer cascade input routing options are shown in TRM
"Figure 12-3224. Timers Overview". For handling beyond multiplexing, the
driver support for timer cascading should be likely be handled via the
clock framework.
The MCU timer controls are also marked as reserved for
usage by the MCU firmware.
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230611111140.3189111-3-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even
timers to create a 64 bit non-atomic counter which is racy in simple
usage, hence the clock muxes are explicitly setup to individual 32 bit
counters driven off system crystal (HFOSC) as default.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230611111140.3189111-2-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Define the aliases at the board level instead of using generic aliases
at SoC level.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-9-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Define the aliases at the board level instead of using generic aliases
at SoC level.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Define the wakeup uart pin-mux for completeness. This allows the
device tree usage in bootloader and firmwares that can configure the
same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Explicitly define the pinmux rather than depend on bootloader configured
pinmux for the platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Using a phandle makes it clear which UART we are choosing without needing
to resolve through an alias first.
Especially useful for boards like the TI J721s2-EVM where the alias is
"serial2" but it actually resolves to the 8th UART instance(main_uart8).
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230601184933.358731-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
As the binding for "current-speed" states, this should only be used
when the baud rate of an attached device cannot be detected. This is
the case for our attached on-board USB-to-UART converter used for
early kernel console. For all other unconnected/disabled ports this
can be configured in userspace later, DT is not the place for device
configuration, especially when there are already standard ways to
set serial baud in userspace.
Remove setting baud for all disabled serial ports and move setting
it for the couple enabled ports down into the board files.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230601184933.358731-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add wakeup and MCU uart. This allows the device tree usage in
bootloader and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: 635fb18ba0 ("arch: arm64: dts: Add support for AM69 Starter Kit")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add wakeup and MCU uart. This allows the device tree usage in
bootloader and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: e20a06aca5 ("arm64: dts: ti: Add support for J784S4 EVM board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
MAIN_PLL0 has a flag set in DM (Device Manager) that removes it's
capability to re-initialise clock frequencies. CPTS and RGMII has
MAIN_PLL3 as their parent which does not have this flag. While RGMII
needs this reinitialisation to default frequency to be able to get
250MHz with its divider, CPTS can not get its required 200MHz with its
divider. Thus, move CPTS clock parent on J721S2 from MAIN_PLL3_HSDIV1 to
MAIN_PLL0_HSDIV6.
(Note: even GTC will be moved from MAIN_PLL3 to MAIN_PLL0 in U-Boot side
for the same reason)
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20230605110443.84568-1-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-15-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-14-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
