In some situations, userspace may want to resolve a
device by function and logical number (ie, "serial0")
rather than by the base address or full device path. Being
able to resolve a device by alias frees userspace from the
burden of otherwise having to maintain a mapping between
device addresses and their logical assignments on each
platform when multiple instances of the same hardware block
are present in the system.
Although the uevent device attribute contains devicetree
compatible information and the full device path, the uevent
does not list the alises that may have been defined for the
device.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
[grant.likely: Removed OF_ALIAS_N field; I don't think it's needed]
[grant.likely: Added #ifndef _LINUX_OF_PRIVATE_H wrapper]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The current test doesn't make a lot of sense. It's likely to be true,
which is what we would want in most cases. From looking at how this is
handled in other drivers, I think "&" was intended instead of "*".
It's an easy mistake to make because they are next to each other on the
keyboard.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Found with coccicheck.
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no firmware was loaded (no exists,wrong or some error) then rmmod
fails with OOPS, so need some protection stuff.
Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SPI controller of the AR7xxx/AR9xxx SoCs
have a special mode which allows the SoC to
directly read data from SPI flash chips. In
this mode, the content of the SPI flash chip
can be accessed via a memory mapped region.
During early init time, the kernel expects
that the flash chip is accessible through
that memory region because it reads board
specific values (e.g. MAC address, WiFi
calibration data) from the flash on various
boards.
This is working if the kernel is loaded
directly by the bootloader because that
leaves the SPI controller in the special
mode. However it is not working in a kexec'd
kernel because the SPI driver does not restore
the special mode during shutdown.
The patch adds a shutdown handler to fix this
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The xfrm gc threshold can be configured via xfrm{4,6}_gc_thresh
sysctl but currently only in init_net, other namespaces always
use the default value. This can substantially limit the number
of IPsec tunnels that can be effectively used.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Function xfrm4_policy_fini() is unused since xfrm4_fini() was
removed in 2.6.11.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch removes the field description of fields that no
longer exists, along side aligns the field description of
fields.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for Digivox Mini HD (rtl2832)
The tuner works, but with worst performance then realtek linux driver,
due to incomplete implementation of fc2580.c
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Tested-by: Lorenzo Dongarrà <lorenzo_64@katamail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The documentation suggested that if the control value is wrong only
ERANGE can be returned. But in some cases (an invalid menu index)
EINVAL can also be returned. Clarify this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The documentation of the error_idx field was incomplete and confusing.
This patch improves it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This is the Renesas IPMMU driver and IOMMU API implementation.
The IPMMU module supports the MMU function and the PMB function. The
MMU function provides address translation by pagetable compatible with
ARMv6. The PMB function provides address translation including
tile-linear translation. This patch implements the MMU function.
The iommu driver does not register a platform driver directly because:
- the register space of the MMU function and the PMB function
have a common register (used for settings flush), so they should ideally
have a way to appropriately share this register.
- the MMU function uses the IOMMU API while the PMB function does not.
- the two functions may be used independently.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add the iommu_domain_window_enable() and iommu_domain_window_disable()
functions to the IOMMU-API. These functions will be used to setup
domains that are based on subwindows and not on paging.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This attribute of a domain can be queried to find out if the
domain supports setting up page-tables using the iommu_map()
and iommu_unmap() functions.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In case the page-size bitmap is zero the code path in
iommu_map and iommu_unmap is undefined. Make it defined and
return -ENODEV in this case.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Fixed the following errors (with exception of the SVG errors):
GEN /home/hans/work/src/v4l/media-git/Documentation/DocBook//v4l2.xml
rm -rf Documentation/DocBook/index.html; echo '<h1>Linux Kernel HTML Documentation</h1>' >> Documentation/DocBook/index.html && echo '<h2>Kernel Version: 3.8.0-rc1</h2>' >> Documentation/DocBook/index.html && cat Documentation/DocBook/media_api.html >> Documentation/DocBook/index.html
/tmp/x.xml:883: element revremark: validity error : Element structname is not declared in revremark list of possible children
/tmp/x.xml:883: element revremark: validity error : Element xref is not declared in revremark list of possible children
/tmp/x.xml:9580: element xref: validity error : Element xref was declared EMPTY this one has content
/tmp/x.xml:13508: element link: validity error : Element link does not carry attribute linkend
/tmp/x.xml:13508: element link: validity error : No declaration for attribute linked of element link
/tmp/x.xml:16986: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
/tmp/x.xml:17003: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
/tmp/x.xml:17022: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PCI IRQs were regressing due to two things:
- The PCI glue layer was using an hard-coded IRQ 27 offset.
This caused the immediate regression.
- The SIC IRQ mask was inverted (i.e. a bit was indeed set to
one for each valid IRQ on the SIC, but accidentally inverted
in the init call). This has been around forever, but we have
been saved by some other forgiving code that would reserve
IRQ descriptors in this range, as the versatile is
non-sparse.
When the IRQs were bumped up 32 steps so as to avoid using IRQ
zero and avoid touching the 16 legacy IRQs, things broke.
Introduce an explicit valid mask for the IRQs that are active
on the PIC/SIC, and pass that. Use the BIT() macro from
<linux/bitops.h> to make sure we hit the right bits, readily
defined in <mach/platform.h>.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 91c2ebb90b (ARM: 7114/1: cache-l2x0: add resume entry for l2
in secure mode) added resume entry for l2 in secure mode, but it missed
the dummy entry when CONFIG_CACHE_L2X0 is not set.
(Commit text edited by rmk.)
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As the default, we blackhole packets until the key manager resolves
the states. This patch implements a packet queue where IPsec packets
are queued until the states are resolved. We generate a dummy xfrm
bundle, the output routine of the returned route enqueues the packet
to a per policy queue and arms a timer that checks for state resolution
when dst_output() is called. Once the states are resolved, the packets
are sent out of the queue. If the states are not resolved after some
time, the queue is flushed.
This patch keeps the defaut behaviour to blackhole packets as long
as we have no states. To enable the packet queue the sysctl
xfrm_larval_drop must be switched off.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Machine/System power-off is run in thermal frame work if
it become critical temperature.
This patch removed pointless machine_power_off()
from thermal_zone_device_ops :: .notify
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds interrupt support for R-Car thermal driver.
New generation R-Car thermal sensor interrupt controller was
different from old generation.
This patch supports new generation sensor only,
since the old generation interrupt controller had never been used before,
and will never be used in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal driver will use struct common in next
feature (interrupt support).
But the register address is different between struct priv and common.
This patch adds read/write functions for struct common,
and use macro technique to avoid wrong register access.
This is preparation patch for next feature (interrupt support),
therefore, there is no user to use this common read/write
function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal sensor will be multi channel sensor in next generation.
But "IRQ controlling method" and "register mapping" are
different between old/new chip.
This patch adds multi sensor support.
Then, this driver assumes there is common register
if platform has IRQ resource.
The IRQ will be supported soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Current R-Car thermal driver is using spin lock for each
registers read/write, but it is pointless lock.
This lock is required while reading temperature,
but it needs long wait (= 300ms).
So, this patch used mutex lock while reading temperature,
instead of spin lock for each registers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If CPCTL was 1 on R-Car thermal, the thermal comparator offset
is automatically decided by hardware.
And this CPCTL is the conditions which validate interrupt.
This patch enabled CPCTL.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
"level" parameter of get_cpu_frequency equals cooling state
of cpu cooling device, and it starts from 0.
Fix the misleading comment.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support to set the emulated temperature method in
thermal zone (sensor). After setting this feature thermal zone may
report this temperature and not the actual temperature. The emulation
implementation may be based on sensor capability through platform
specific handler or pure software emulation if no platform handler defined.
This is useful in debugging different temperature threshold and its
associated cooling action. Critical threshold's cannot be emulated.
Writing 0 on this node should disable emulation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This value has already been clamped correctly to 0 through 49 in
powerclamp_set_cur_state() so this patch doesn't actually change
anything. But we should fix it anyway for consistency.
set_target_ratio is used as an offset into an array with
MAX_TARGET_RATIO (50) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Below fixes are done to support falling threshold interrupt,
* Falling interrupt status macro corrected according to exynos5 data sheet.
* The get trend function modified to calculate trip temperature correctly.
* The clearing of interrupt status in the isr is now done after handling
the event that caused the interrupt.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Intel PowerClamp driver performs synchronized idle injection across
all online CPUs. The goal is to maintain a given package level C-state
ratio.
Compared to other throttling methods already exist in the kernel,
such as ACPI PAD (taking CPUs offline) and clock modulation, this is often
more efficient in terms of performance per watt.
Please refer to Documentation/thermal/intel_powerclamp.txt for more details.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use pcmcia_request_irq() instead of request_irq() to request the
shared irq for the PCMCIA device. This allows the PCMCIA core to
clean up the registration in pcmcia_disable_device().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
This driver uses a local (*conf_check) to check the pcmcia_device
configuration.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow comedi pcmcia drivers to use a custom conf_check() when calling
comedi_pcmcia_enable() to enable the pcmcia device. If a conf_check()
is not passed the internal comedi_pcmcia_conf_check() will be used.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
This driver is not an audio device, remove CONF_AUTO_AUDIO from
the link->config_flags.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
This driver does not use interrupts and is not an audio device, remove
CONF_ENABLE_IRQ and CONF_AUTO_AUDIO from the link->config_flags.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In comedi drivers typically *_attach_common() is used as the 'common'
part of the comedi_driver attach code for drivers that support various
bus types (ISA, PCI, etc.). This driver is specific to a USB device.
To avoid confusion when grepping, rename this function to something
more appropriate.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
git history provides a better Changelog for the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vmk8055_range table is a duplicate of the comedi core provided
range_unipolar5 table. Use that instead.
For aesthetic reasons, clean up the formating of the vmk8061_range
table.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
