This patch fixes a bug which causes all histogram regions to start in the
top left corner of the image. The histogram region coordinates are 16 bit
values which share a 32 bit register. The bug is due to the region end
value assignments overwriting the region start values with zero.
Signed-off-by: Johannes Schellen <Johannes.Schellen@rwth-aachen.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kzalloc initializes the memory it allocates to 0, there's no need for an
explicit memset.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The preview engine includes filters that consume columns and lines as
part of their operation, thus resulting in a cropped image. To allow
turning those filters on/off during streaming without affecting the
output image size, the driver adds additional cropping to make the total
number of cropped columns and lines constant regardless of which filters
are enabled.
This process needlessly includes the CFA filter, as whether the filter
is enabled only depends on the sink pad format, which can't change
during streaming.
Exclude the CFA filter from the preview engine margins.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the pin controller of sunxi chips is represented as a
single bank in the driver.
Since this is neither convenient nor represented that way in the
datasheets, define a custom of_xlate function with the layout
<bank pin flag>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct udf_bitmap has array of buffer pointers attached to it. The code
unnecessarily used s_block_bitmap as a pointer to the array instead of
the standard trick of using 0 length array in the declaration. Change
that to make code more readable and actually shrink the structure by one
pointer.
Signed-off-by: Jan Kara <jack@suse.cz>
For large UDF filesystems with 512-byte blocks the number of necessary
bitmap blocks is larger than 2^16 so s_nr_groups in udf_bitmap overflows
(the number will overflow for filesystems larger than 128 GB with
512-byte blocks). That results in ENOSPC errors despite the filesystem
has plenty of free space.
Fix the problem by changing s_nr_groups' type to 'int'. That is enough
even for filesystems 2^32 blocks (UDF maximum) and 512-byte blocksize.
Reported-and-tested-by: v10lator@myway.de
Signed-off-by: Jan Kara <jack@suse.cz>
Add the missing unlock on the error handling path in function
vpbe_initialize().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be
used uninitialized in this function [-Wuninitialized]
drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here
This is a false positive but the compiler has no way to know about it,
so initialize the variable to 0.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't need a temporary variable just to store the return value which
gets return in the next statement.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Err is never read before it is assigned again -> remove the dead
assigment.
Found with clang static analyzer
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
With the HOTPLUG changes 3.8 this attribute is going away.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
We don't need to call memcpy for one byte, but assign it directly.
And to make the offset clearer we use the array syntax on the subsequent
call to memset to make the relationship clearer.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The TIS specification (pg 47) says the valid bit must be set, but
the TPM will not set it until it has completed its internal startup.
The driver checks that the valid bit is set during request_locality,
but it issues a TPM_ACCESS_REQUEST_USE without validating the
valid bit is set.
Some TPMs will ignore the TPM_ACCESS_REQUEST_USE, until valid is
set which causes the request_locality to timeout, which breaks the
driver attach.
Wait one timeout unit for valid to assert. If valid does not assert
then assume -ENODEV.
Seen on embedded with a:
1.2 TPM (device-id 0x3204, rev-id 64)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Support cancellation of TPM commands when driver is used in interrupt
mode.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.
This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
We've been testing an alternative TPM for our embedded products and
found random kernel boot failures due to time outs after the continue
self test command.
This was happening randomly, and has been *very* hard to track down, but
it
looks like with this chip there is some kind of race with the
tpm_tis_status()
check of TPM_STS_COMMAND_READY. If things get there 'too fast' then
it sees the chip is ready, or tpm_tis_ready() works. Otherwise it takes
somewhere over 400ms before the chip will return TPM_STS_COMMAND_READY.
Adding some delay after tpm_continue_selftest() makes things reliably
hit the failure path, otherwise it is a crapshot.
The spec says it should be returning TPM_WARN_DOING_SELFTEST, not
holding
off on ready..
Boot log during this event looks like this:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0x3204, rev-id 64)
tpm_tis 70030000.tpm_tis: Issuing TPM_STARTUP
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
The other TPM vendor we use doesn't show this wonky behaviour:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0xFE, rev-id 70)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
When no i2c bus exists, user-space can cause an oops by triggering a
device probe through a message sent to an i2c "new_device" sysfs entry.
Adding a check for a NULL i2c client structure in the probe function
closes the hole.
This patch also fixes accessing the NULL client struct in the print
function call reporting the error.
Reported-by: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch converts the suspend and resume functions for
tpm_i2c_stm_st33 to the new dev_pm_ops.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64, beagleboard REV B & XM REV C and CHROMIUM OS
Signed-off-by: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Store the i2c_client struct in the vendor private pointer. Get rid of
the unnecessary include/linux/i2c/ header. Moved include files into the
driver c file. Fix smatch warnings. Make use of module_i2c_driver().
Removed unused code from the tpm_stm_st33_i2c.h file. Fix return
variable signedness in tpm_stm_i2c_send() and tpm_st33_i2c_probe().
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
