Several bits in CNTKCTL reset to 0, including PL0VTEN. For architectures
using the generic timer which wish to have a fast gettimeofday vDSO
implementation, these bits must be set to 1 by the kernel. For
architectures without a vDSO, it's best to leave the bits set to 0 for
now to ensure that if and when support is added, it's implemented sanely
architecture wide.
As the bootloader might set PL0VTEN to a value that doesn't correspond
to that which the kernel prefers, we must explicitly set it to the
architecture port's preferred value.
This patch adds arch_counter_set_user_access, which sets the PL0 access
permissions to that required by the architecture. For arch/arm, this
currently means disabling all userspace access.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, the arch_timer driver is tied to the arm port, as it relies
on code in arch/arm/smp.c to setup and teardown timers as cores are
hotplugged on and off. The timer is registered through an arm-specific
registration mechanism, preventing sharing the driver with the arm64
port.
This patch moves the driver to using a cpu notifier instead, making it
easier to port.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Without the isbs in arch_timer_get_cnt{p,v}ct the cpu may speculate
reads and return stale values. This could be bad for code sensitive to
changes in expected deltas between calls (e.g. the delay loop).
Without isbs in arch_timer_reg_write the processor may reorder
instructions around enabling/disabling of the timer or writing the
compare value, which we probably don't want.
This patch adds isbs to prevent those issues.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Currently the arch_timer register accessors are thrown together with
the main driver, preventing us from porting the driver to other
architectures.
This patch moves the register accessors into a header file, as with
the arm64 version. Constants required by the accessors are also moved.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The CNTFRQ register is not duplicated for physical and virtual timers,
and accessing it as if it were is confusing.
Instead, use a separate accessor which doesn't take the access type
as a parameter.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
We're currently inconsistent with respect to our accesses to the
physical and virtual counters, mixing and matching the two.
This patch introduces and uses a function pointer for accessing the
correct counter based on whether we're using physical or virtual
interrupts. All current accesses to the counter accessors are redirected
through it.
When the driver is moved out to drivers/clocksource, there's the
possibility that code called before the timer code is initialised will
attempt to call arch_timer_read_counter (e.g. sched_clock for AArch64).
To avoid having to have to check whether the timer has been initialised
either in arch_timer_read_counter or one of it's callers, a default
implementation is assigned that simply returns 0.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
To ensure the correct size of types, use u64 for the return value of
arch_timer_get_cnt{p,v}ct, and u32 for arch_timer_rate, matching the
size of the registers these values are taken from. While we're changing
them anyway, simplify the implementation of arch_timer_get_cnt{p,v}ct.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This check is a holdover from the pre-devicetree days. As the timer
is not probed except by platforms which register it via devicetree,
it's not strictly necessary.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
When we get the device_node for the arch timer, it's refcount is
automatically incremented in of_find_matching_node, but it is
never decremented.
This patch decrements the refcount on the node after we're finished
using it.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
We usually group drivers on a per-vendor basis, implementing device-specific
deviations from the standard in vendor-specific driver.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch vastly improve latency while scanning. Slight throughput
improvements were observed as well. Is intended for improve performance
of voice and video applications, when scan is periodically requested by
user space (i.e. default NetworkManager behaviour).
Patch remove latency requirement based on PM_QOS_NETWORK_LATENCY,
this value is 2000 seconds by default (i.e. approximately 0.5 hour !?!).
Also remove listen interval requirement, which based on beaconing and
depending on BSS parameters. It can make we stay off-channel for a
second or more.
Instead try to offer the best latency that we could, i.e. be off-channel
no longer than PASSIVE channel scan time: 125 ms. That mean we will
scan two ACTIVE channels and go back to on-channel, and one PASSIVE
channel, and go back to on-channel.
Patch also decrease PASSIVE channel scan time to about 110 ms.
As drawback patch increase overall scan time. On my tests, when scanning
both 2GHz and 5GHz bands, scanning time increase from 5 seconds up to 10
seconds. Since that increase happen only when we are associated, I think
it can be acceptable. If eventually better scan time is needed for
situations when we lose signal and quickly need to decide to which AP
roam, additional scan flag or parameter can be introduced.
I tested patch by doing:
while true; do iw dev wlan0 scan; sleep 3; done > /dev/null
and
ping -i0.2 -c 1000 HOST
on remote and local machine, results are as below:
* Ping from local periodically scanning machine to AP:
Unpatched: rtt min/avg/max/mdev = 0.928/24.946/182.135/36.873 ms
Patched: rtt min/avg/max/mdev = 0.928/19.678/150.845/33.130 ms
* Ping from remote machine to periodically scanning machine:
Unpatched: rtt min/avg/max/mdev = 1.637/120.683/709.139/164.337 ms
Patched: rtt min/avg/max/mdev = 1.807/26.893/201.435/40.284 ms
Throughput measured by scp show following results.
* Upload to periodically scanning machine:
Unpatched: 3.9MB/s 03:15
Patched: 4.3MB/s 02:58
* Download from periodically scanning machine:
Unpatched: 5.5MB/s 02:17
Patched: 6.2MB/s 02:02
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch to the SRW-S1 driver adds the ability to control all
LEDs simultaneously as testing showed that it was slow (noticably!!)
when seting or clearing all the LEDs in turn.
It adds a 'RPMALL' LED, whose behavoir is asserted to all the LEDs in
the bar graph, individual LEDs can subsequently be turned on/off
individually.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver adds support for the LED RPM
meter on the front of the device. The LEDs are controlled via
/sys/class/leds interface, with an individual control for each
of the 15 LEDs.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver re-writes the HID descriptor
to insert a section for the 3 dials on the device, previously
these were contained within a 'Manufacturer Specific' usage
page.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support the SRW-S1 by patching HID descriptor to read axis
as Generic Desktop X, Y and Z (rather than Usage page being
'Simulation').
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Although the patchcheck test checks for warnings in the files that were
changed, this check does not catch warnings that were caused by header
file changes and the warnings appear in C files not touched by the
commit.
Add a new option called WARNINGS_FILE. If this option is set, then the
file it points to is read before bulid, and the file should contain a
list of known warnings. If a warning appears in the build, this file is
checked, and if the warning does not exist in this file, then it fails
the build showing the new warning.
If the WARNINGS_FILE points to a file that does not exist, this will
cause any warning in the build to fail.
A new test is also added called "make_warnings_file". This test will
create do a build and record any warnings it finds into the
WARNINGS_FILE. This test is something that can be run before other tests
to build a warnings file of "known warnings", ie, warnings that were
there before your changes.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Options are allowed to use other options, for example:
LOG_FILE = ${OUTPUT_DIR}/${MACHINE}.log
where the option LOG_FILE used the options OUTPUT_DIR and MACHINE.
But if a test option were to use a default option, it will not get
substituted:
OUTPUT_DIR = ${THIS_DIR}/${MACHINE}
TEST_START
OUTPUT_DIR = ${OUTPUT_DIR}/t1
For the above test, OUTPUT_DIR will stay literally "${OUTPUT_DIR}/t1"
and not be converted to "${THIS_DIR}/${MACHINE}/t1". When the test runs,
it will pass the ${OUTPUT_DIR} to the shell, which would probaly
interpret it as "", and the output directory will end up as "/t1".
Change the code where if a test option has its own option name in
its defined field, and a default option exists, then substitute the
default option in its place.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of adding a magic 4 to the variable size, use sizeof() to make
it explicitly clear what the quantity represents (the variable's
attributes).
CC: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Chun-Yi Lee <joeyli.kernel@gmail.com>
Cc: Andy Whitcroft <apw@canonical.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
When initrd file didn't put at the same place with stub kernel, we
need give the file path of initrd, but need use backslash to separate
directory and file. It's not friendly to unix/linux user, and not so
intuitive for bootloader forward paramters to efi stub kernel by
chainloading.
This patch add support to handle_ramdisks for allow slash in file path
of initrd, it convert slash to backlash when parsing path.
In additional, this patch also separates print code of efi_char16_t from
efi_printk, and print out the path/filename of initrd when failed to open
initrd file. It's good for debug and discover typo.
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Device-mapper WRITE SAME support was introduced by commit
23508a96cd ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
This patch cleans unneccessary includes and reorders the remaining
includes in common dove code.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
After removing the unneeded linux/i2c.h, linux/of.h was needed for
of_machine_is_compatible(). i2c.h had included of.h.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit d3ce884318 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 no longer uses this API, remove
it completely. If anyone needs it again, we can
revert this patch of course, but mac80211 was the
only user right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ed4f209 "s390/time: fix sched_clock() overflow" a new helper function
is used to avoid overflows when converting TOD format values to nanosecond
values.
The kvm interrupt code formerly however only worked by accident because of
an overflow. It tried to program a timer that would expire in more than ~29
years. Because of the old TOD-to-nanoseconds overflow bug the real expiry
value however was much smaller, but now it isn't anymore.
This however triggers yet another bug in the function that programs the clock
comparator s390_next_ktime(): if the absolute "expires" value is after 2042
this will result in an overflow and the programmed value is lower than the
current TOD value which immediatly triggers a clock comparator (= timer)
interrupt.
Since the timer isn't expired it will be programmed immediately again and so
on... the result is a dead system.
To fix this simply program the maximum possible value if an overflow is
detected.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: Luis Llorente <luisllorente@luisllorente.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the dft_brightness validity check from the DT parsing function to the
main probe. In this way we can validate it in case we are booting with or
without DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Some compilers complain when building sound for MOP500:
sound/soc/ux500/mop500.c:27:27:
fatal error: mop500_ab8500.h: No such file or directory
That file is actually in the local directory rather than include.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
From BSpec / SR01 - Clocking Mode:
"The following sequence must be used when disabling the VGA plane.
Write SR01 to set bit 5 = 1 to disable video output.
Wait for 100us.
Disable the VGA plane via Bit 31 of the MMIO VGA control."
So simply call i915_disable_vga() from i915_redisable_vga().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All display registers should now include the proper offset on VLV.
That means IS_DISPLAYREG() is now useless, and we can eliminate it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VGACNTRL register has moved around between different platforms.
To handle the differences add i915_vgacntrl_reg() which returns the
correct offset for the VGACNTRL register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can disable (almost) all the display hw if we only use pipe A, with
the integrated edp transcoder on port A. Because we don't set the cpu
transcoder that early (yet), we need to help us with a trick to simply
check for any edp encoders.
v2: Paulo Zanoni pointed out that we also need to configure the eDP
cpu transcoder correctly.
v3: Made by Paulo Zanoni
- Rebase patch to be on top of "fix intel_init_power_wells" patch
- Fix typos
- Fix a small bug by adding a "connectors_active" check
- Restore the initial code that unconditionally enables the power
well when taking over from the BIOS
v4: Made by Paulo Zanoni
- One more typo spotted by Jani Nikula
v5: Made by Paulo Zanoni
- Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the power well is disabled, we should not try to read its
registers, otherwise we'll get "unclaimed register" messages.
V2: Don't check whether the power well is enabled or not, just check
whether we asked it to be enabled or not: if we asked to disable the
power well, don't use the registers on it, even if it's still enabled.
V3: Fix bug that breaks all non-Haswell machines.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP_TP_STATUS register for PORT_A doesn't exist. Our documentation
will be fixed soon, so the code does not match it for now.
This solves "Timed out waiting for DP idle patterns" and "unclaimed
register" messages on eDP.
V1: Was called "drm/i915: don't read DP_TP_STATUS(PORT_A)"
V2: Was called "drm/i915: don't send DP idle pattern before normal
pattern on HSW"
V3: Only change the code that touches PORT_A.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may not concurrently change the power wells code. Which
is already guaranteed since modesets aren't concurrent. That
leaves races against setup/teardown/suspend/resume, and for
those we already (try) rather hard not to hit concurrent
modesets.
No debug WARN_ON added since that would require us to grab the
modeset locks in init/suspend code. Which is again just cargo
culting since just grabbing the locks in those paths isn't good
enough, we need the right order of operations, too.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding the fb idle detection to mark-inactive, it was forgotten
that userspace can drive the processing of retire-requests. We assumed
that it would be principally driven by the retire requests worker,
running once every second whilst active and so we would get the deferred
timer for free. Instead we spend too many CPU cycles reclocking the LVDS
preventing real work from being done.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alexander Lam <lambchop468@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58843
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The shift changed, hurray.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
