The CX23885 IR controller was reported to cause an interrupt storm
on a TeVii S470 card, but was reported fine on an HVR-1250. Keep
integrated IR disabled by default on CX2388[57] based cards to avoid
a bad user experience in the general case.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Interrupts from the AV Core are best handled by a workqueue handler
since many I2C transactions are required to service the AV Core
interrupt. The AV_CORE PCI interrupt is disabled by the IRQ handler
and reenabled when the work handler is finished.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch encapsulates access to the PCI_INT_MSK register and
dev->pci_irqmask variable and protects them with a spinlock.
This is needed because both the hard IRQ handler and a workhandler
will need to manipulate the mask to disable the AV_CORE interrupt.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial IR Rx support using the intergrated IR controller in the
A/V core of the CX23885 bridge chip.
This initial support is flawed in that I2C transactions should not
be performed in a hard irq context. That will be fixed in a
follow on patch.
The TeVii S470 support is reported to generate perptual interrupts
that renders a user' system nearly unusable. The TeVii S470 IR
will be disabled by default in a follow on patch.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c. Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.
For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver. For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.
IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.
Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense. The CX23887 likely suffers from
the same quirk. For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.
For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released. This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't just check for nacks on zero-length transactions. Check on
other transactions too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Documentation/i2c/fault-codes says that i2c adapter drivers should
return -ENXIO when no slave acks an address byte.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On laptops, the webcam sometimes disconnects when writing the first main
register (b300). This patch prevents the creation of a new /dev/video<n>
on streaming start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The added controls are exposure, gain, autogain and backlight compensation.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG format did not work fine. The Bayer format offers correct VGA (640x480)
resolution, but bad QQVGA (160x120). This last resolution is removed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 7 of the sensor gain register multiplies the 7bits value by two.
It is now always set with half the user gain value.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The start_1 exchange must be done by (reg, val) * 5 and not 8.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: check kmalloc() result
arch/tile: catch up on various minor cleanups.
arch/tile: avoid erroneous error return for PTRACE_POKEUSR.
tile: set ARCH_KMALLOC_MINALIGN
tile: remove homegrown L1_CACHE_ALIGN macro
arch/tile: Miscellaneous cleanup changes.
arch/tile: Split the icache flush code off to a generic <arch> header.
arch/tile: Fix bug in support for atomic64_xx() ops.
arch/tile: Shrink the tile-opcode files considerably.
arch/tile: Add driver to enable access to the user dynamic network.
arch/tile: Enable more sophisticated IRQ model for 32-bit chips.
Move list types from <linux/list.h> to <linux/types.h>.
Add wait4() back to the set of <asm-generic/unistd.h> syscalls.
Revert adding some arch-specific signal syscalls to <linux/syscalls.h>.
arch/tile: Do not use GFP_KERNEL for dma_alloc_coherent(). Feedback from fujita.tomonori@lab.ntt.co.jp.
arch/tile: core support for Tilera 32-bit chips.
Fix up the "generic" unistd.h ABI to be more useful.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (82 commits)
firewire: core: add forgotten dummy driver methods, remove unused ones
firewire: add isochronous multichannel reception
firewire: core: small clarifications in core-cdev
firewire: core: remove unused code
firewire: ohci: release channel in error path
firewire: ohci: use memory barriers to order descriptor updates
tools/firewire: nosy-dump: increment program version
tools/firewire: nosy-dump: remove unused code
tools/firewire: nosy-dump: use linux/firewire-constants.h
tools/firewire: nosy-dump: break up a deeply nested function
tools/firewire: nosy-dump: make some symbols static or const
tools/firewire: nosy-dump: change to kernel coding style
tools/firewire: nosy-dump: work around segfault in decode_fcp
tools/firewire: nosy-dump: fix it on x86-64
tools/firewire: add userspace front-end of nosy
firewire: nosy: note ioctls in ioctl-number.txt
firewire: nosy: use generic printk macros
firewire: nosy: endianess fixes and annotations
firewire: nosy: annotate __user pointers and __iomem pointers
firewire: nosy: fix device shutdown with active client
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
ACPI / ACPICA: Simplify acpi_ev_initialize_gpe_block()
ACPI / ACPICA: Fail acpi_gpe_wakeup() if ACPI_GPE_CAN_WAKE is unset
ACPI / ACPICA: Do not execute _PRW methods during initialization
ACPI: Fix bogus GPE test in acpi_bus_set_run_wake_flags()
ACPICA: Update version to 20100702
ACPICA: Fix for Alias references within Package objects
ACPICA: Fix lint warning for 64-bit constant
ACPICA: Remove obsolete GPE function
ACPICA: Update debug output components
ACPICA: Add support for WDDT - Watchdog Descriptor Table
ACPICA: Drop acpi_set_gpe
ACPICA: Use low-level GPE enable during GPE block initialization
ACPI / EC: Do not use acpi_set_gpe
ACPI / EC: Drop suspend and resume routines
ACPICA: Remove wakeup GPE reference counting which is not used
ACPICA: Introduce acpi_gpe_wakeup()
ACPICA: Rename acpi_hw_gpe_register_bit
ACPICA: Update version to 20100528
ACPICA: Add signatures for undefined tables: ATKG, GSCI, IEIT
ACPICA: Optimization: Reduce the number of namespace walks
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Add missing <linux/slab.h> include
IB/ehca: Drop unnecessary NULL test
RDMA/nes: Fix confusing if statement indentation
IB/ehca: Init irq tasklet before irq can happen
RDMA/nes: Fix misindented code
RDMA/nes: Fix showing wqm_quanta
RDMA/nes: Get rid of "set but not used" variables
RDMA/nes: Read firmware version from correct place
IB/srp: Export req_lim via sysfs
IB/srp: Make receive buffer handling more robust
IB/srp: Use print_hex_dump()
IB: Rename RAW_ETY to RAW_ETHERTYPE
RDMA/nes: Fix two sparse warnings
RDMA/cxgb3: Make needlessly global iwch_l2t_send() static
IB/iser: Make needlessly global iser_alloc_rx_descriptors() static
RDMA/cxgb4: Add timeouts when waiting for FW responses
IB/qib: Fix race between qib_error_qp() and receive packet processing
IB/qib: Limit the number of packets processed per interrupt
IB/qib: Allow writes to the diag_counters to be able to clear them
IB/qib: Set cfgctxts to number of CPUs by default
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: Do not suspend IPI IRQs.
powerpc: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupts
ixp4xx-beeper: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupt
irq: Add new IRQ flag IRQF_NO_SUSPEND
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (28 commits)
driver core: device_rename's new_name can be const
sysfs: Remove owner field from sysfs struct attribute
powerpc/pci: Remove owner field from attribute initialization in PCI bridge init
regulator: Remove owner field from attribute initialization in regulator core driver
leds: Remove owner field from attribute initialization in bd2802 driver
scsi: Remove owner field from attribute initialization in ARCMSR driver
scsi: Remove owner field from attribute initialization in LPFC driver
cgroupfs: create /sys/fs/cgroup to mount cgroupfs on
Driver core: Add BUS_NOTIFY_BIND_DRIVER
driver core: fix memory leak on one error path in bus_register()
debugfs: no longer needs to depend on SYSFS
sysfs: Fix one more signature discrepancy between sysfs implementation and docs.
sysfs: fix discrepancies between implementation and documentation
dcdbas: remove a redundant smi_data_buf_free in dcdbas_exit
dmi-id: fix a memory leak in dmi_id_init error path
sysfs: sysfs_chmod_file's attr can be const
firmware: Update hotplug script
Driver core: move platform device creation helpers to .init.text (if MODULE=n)
Driver core: reduce duplicated code for platform_device creation
Driver core: use kmemdup in platform_device_add_resources
...
Commit 69309a0590 ("x86, asm: Clean up and simplify set_64bit()")
sanitized the x86-64 types to set_64bit(), and incidentally resulted in
warnings like
drivers/pci/intr_remapping.c: In function 'modify_irte':
drivers/pci/intr_remapping.c:314: warning: passing argument 1 of 'set_64bit' from incompatible pointer type
arch/x86/include/asm/cmpxchg_64.h:6: note:expected 'volatile u64 *' but argument is of type 'long unsigned int *'
It turns out that the change to set_64bit() really does clean up things,
and the PCI intr_remapping.c file did a rather ugly cast in order to
avoid warnings with the previous set_64bit() type model.
Removing the ugly cast fixes the warning, and makes everybody happy and
expects a set_64bit() to take the logical "u64 *" argument.
Pointed-out-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (162 commits)
tracing/kprobes: unregister_trace_probe needs to be called under mutex
perf: expose event__process function
perf events: Fix mmap offset determination
perf, powerpc: fsl_emb: Restore setting perf_sample_data.period
perf, powerpc: Convert the FSL driver to use local64_t
perf tools: Don't keep unreferenced maps when unmaps are detected
perf session: Invalidate last_match when removing threads from rb_tree
perf session: Free the ref_reloc_sym memory at the right place
x86,mmiotrace: Add support for tracing STOS instruction
perf, sched migration: Librarize task states and event headers helpers
perf, sched migration: Librarize the GUI class
perf, sched migration: Make the GUI class client agnostic
perf, sched migration: Make it vertically scrollable
perf, sched migration: Parameterize cpu height and spacing
perf, sched migration: Fix key bindings
perf, sched migration: Ignore unhandled task states
perf, sched migration: Handle ignored migrate out events
perf: New migration tool overview
tracing: Drop cpparg() macro
perf: Use tracepoint_synchronize_unregister() to flush any pending tracepoint call
...
Fix up trivial conflicts in Makefile and drivers/cpufreq/cpufreq.c
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Export cache-coherency capability
iommu-api: Extension to check for interrupt remapping
x86/amd-iommu: Use for_each_pci_dev()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl,mv,nv: prepare for NCQ command completion update
ata: Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
libata: more PCI IDs for jmicron controllers
ata_piix: fix locking around SIDPR access
[libata] update blacklist for new hyphenated pattern ranges (v2)
libata: allow hyphenated pattern ranges
ata_generic: drop hard coded DMA force logic for CENATEK
[libata] ahci: Fix warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
[libata] add ATA_CMD_DSM to ata_get_cmd_descript
[libata] Add Samsung PATA controller driver, pata_samsung_cf
[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex
libata: reduce blacklist size even more (v2)
libata: reduce blacklist size (v2)
libata: glob_match for ata_device_blacklist (v2)
ahci_platform: Remove unneeded ahci_driver.probe assignment
ahci_platform: Provide for vendor specific init
Fake "address-of" expressions that evaluate to NULL generally confuse
readers and can provoke compiler warnings. This patch (as1411) removes
one such fake expression, using an "#ifdef" in its place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make /dev/console get initialised before any initialisation routine that
invokes modprobe because if modprobe fails, it's going to want to open
/dev/console, presumably to write an error message to.
The problem with that is that if the /dev/console driver is not yet
initialised, the chardev handler will call request_module() to invoke
modprobe, which will fail, because we never compile /dev/console as a
module.
This will lead to a modprobe loop, showing the following in the kernel
log:
request_module: runaway loop modprobe char-major-5-1
request_module: runaway loop modprobe char-major-5-1
request_module: runaway loop modprobe char-major-5-1
request_module: runaway loop modprobe char-major-5-1
request_module: runaway loop modprobe char-major-5-1
This can happen, for example, when the built in md5 module can't find
the built in cryptomgr module (because the latter fails to initialise).
The md5 module comes before the call to tty_init(), presumably because
'crypto' comes before 'drivers' alphabetically.
Fix this by calling tty_init() from chrdev_init().
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>