right now the returned value is considered to be always valid. However,
when playing with HID-BPF, the return value can be arbitrary big,
because it's the return value of dispatch_hid_bpf_raw_requests(), which
calls the struct_ops and we have no guarantees that the value makes
sense.
Fixes: 8bd0488b5e ("HID: bpf: add HID-BPF hooks for hid_hw_raw_requests")
Cc: stable@vger.kernel.org
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
This can happen in situations when CONFIG_HID_SUPPORT is set to no, or
some complex situations where struct bpf_wq is not exported.
So do the usual dance of hiding them before including vmlinux.h, and
then redefining them and make use of CO-RE to have the correct offsets.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202603111558.KLCIxsZB-lkp@intel.com/
Fixes: fe8d561db3 ("selftests/hid: add wq test for hid_bpf_input_report()")
Cc: stable@vger.kernel.org
Acked-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The memset() in hid_report_raw_event() has the good intention of
clearing out bogus data by zeroing the area from the end of the incoming
data string to the assumed end of the buffer. However, as we have
previously seen, doing so can easily result in OOB reads and writes in
the subsequent thread of execution.
The current suggestion from one of the HID maintainers is to remove the
memset() and simply return if the incoming event buffer size is not
large enough to fill the associated report.
Suggested-by Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
[bentiss: changed the return value]
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
When 1-bit bus width is used with HS200/HS400 capabilities set,
mmc_select_hs200() returns 0 without actually switching. This
causes mmc_select_timing() to skip mmc_select_hs(), leaving eMMC
in legacy mode (26MHz) instead of High Speed SDR (52MHz).
Per JEDEC eMMC spec section 5.3.2, 1-bit mode supports High Speed
SDR. Drop incompatible HS200/HS400/UHS/DDR caps early so timing
selection falls through to mmc_select_hs() correctly.
Fixes: f2119df6b7 ("mmc: sd: add support for signal voltage switch procedure")
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
setup_fifo_params computes mode_changed from spi->mode flags but tests
it against SE_SPI_CPHA and SE_SPI_CPOL, which are register offsets,
not SPI mode bits. This causes CPHA and CPOL updates to be skipped
on mode switches, leaving the controller with stale clock phase
and polarity settings.
Fix this by using SPI_CPHA and SPI_CPOL to detect mode changes before
updating the corresponding registers.
Fixes: 781c3e71c9 ("spi: spi-geni-qcom: rework setup_fifo_params")
Signed-off-by: Maramaina Naresh <naresh.maramaina@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316-spi-geni-cpha-cpol-fix-v1-1-4cb44c176b79@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions in the arm64 kernel's cputype.h are kernel specific and
cause perf build failures when the header is synced into tools.
Stop checking arm64's cputype.h. In the future, the header in tools
will be updated manually when teaching tools about new CPUs.
Signed-off-by: Leo Yan <leo.yan@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a device performs DMA to a bounce buffer, KMSAN is unaware of
the write and does not mark the data as initialized. When
swiotlb_bounce() later copies the bounce buffer back to the original
buffer, memcpy propagates the uninitialized shadow to the original
buffer, causing false positive uninit-value reports.
Fix this by calling kmsan_unpoison_memory() on the bounce buffer
before copying it back in the DMA_FROM_DEVICE path, so that memcpy
naturally propagates initialized shadow to the destination.
Suggested-by: Alexander Potapenko <glider@google.com>
Link: https://lore.kernel.org/CAG_fn=WUGta-paG1BgsGRoAR+fmuCgh3xo=R3XdzOt_-DqSdHw@mail.gmail.com/
Fixes: 7ade4f1077 ("dma: kmsan: unpoison DMA mappings")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20260315082750.2375581-1-syoshida@redhat.com
Currently HID_PHYS is empty, which means userspace tools (e.g. fwupd)
that depend on it for distinguishing the devices, are unable to do so.
Other drivers like i2c-hid, usbhid, surface-hid, all populate it.
With this change it's set to, for example: HID_PHYS=0000:00:10.0
Each function has just a single HID device, as far as I can tell, so
there is no need to add a suffix.
Tested with fwupd 2.1.1, can avoid https://github.com/fwupd/fwupd/pull/9995
Cc: Even Xu <even.xu@intel.com>
Cc: Xinpeng Sun <xinpeng.sun@intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <bentiss@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Daniel Schaefer <git@danielschaefer.me>
Reviewed-by: Even Xu <even.xu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
A XFRM_MSG_NEWSPDINFO request can queue the per-net work item
policy_hthresh.work onto the system workqueue.
The queued callback, xfrm_hash_rebuild(), retrieves the enclosing
struct net via container_of(). If the net namespace is torn down
before that work runs, the associated struct net may already have
been freed, and xfrm_hash_rebuild() may then dereference stale memory.
xfrm_policy_fini() already flushes policy_hash_work during teardown,
but it does not synchronize policy_hthresh.work.
Synchronize policy_hthresh.work in xfrm_policy_fini() as well, so the
queued work cannot outlive the net namespace teardown and access a
freed struct net.
Fixes: 880a6fab8f ("xfrm: configure policy hash table thresholds by netlink")
Signed-off-by: Minwoo Ra <raminwo0202@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
ADATA SU680 SSDs suffer from NCQ read and write commands timeouts or bus
errors when link power management (LPM) is enabled. Flag these devices
with the ATA_QUIRK_NOLPM quirk to prevent the use of LPM and avoid these
command failures.
Reported-by: Mohammad Khaled Bayan <mhd.khaled.bayan@gmail.com>
Closes: https://bugs.launchpad.net/ubuntu/+source/linux-hwe-6.17/+bug/2144060
Cc: stable@vger.kernel.org
Tested-by: Mohammad-Khaled Bayan <mhd.khaled.bayan@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been
initialized, and dmc is thus NULL.
That would be the case when the call path is
intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() ->
gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as
intel_power_domains_init_hw() is called *before* intel_dmc_init().
However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count()
conditionally, depending on the current and target DC states. At probe,
the target is disabled, but if DC6 is enabled, the function is called,
and an oops follows. Apparently it's quite unlikely that DC6 is enabled
at probe, as we haven't seen this failure mode before.
It is also strange to have DC6 enabled at boot, since that would require
the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and
the driver stopping / reprogramming the firmware is a poorly specified
sequence and as such unlikely an intentional BIOS behaviour. It's more
likely that BIOS is leaving an unintentionally enabled DC6 HW state
behind (without actually loading the required DMC firmware for this).
The tracking of the DC6 allowed counter only works if starting /
stopping the counter depends on the _SW_ DC6 state vs. the current _HW_
DC6 state (since stopping the counter requires the DC5 counter captured
when the counter was started). Thus, using the HW DC6 state is incorrect
and it also leads to the above oops. Fix both issues by using the SW DC6
state for the tracking.
This is v2 of the fix originally sent by Jani, updated based on the
first Link: discussion below.
Link: https://lore.kernel.org/all/3626411dc9e556452c432d0919821b76d9991217@intel.com
Link: https://lore.kernel.org/all/20260228130946.50919-2-ltao@redhat.com
Fixes: 88c1f9a4d3 ("drm/i915/dmc: Create debugfs entry for dc6 counter")
Cc: Mohammed Thasleem <mohammed.thasleem@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Tao Liu <ltao@redhat.com>
Cc: <stable@vger.kernel.org> # v6.16+
Tested-by: Tao Liu <ltao@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260309164803.1918158-1-imre.deak@intel.com
(cherry picked from commit 2344b93af8)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Most of VM feature detections are integer OR operations, and integer
assignment operation will clear previous integer OR operation. So here
change all integer assignment operations to integer OR operations.
Fixes: 82db90bf46 ("LoongArch: KVM: Move feature detection in kvm_vm_init_features()")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Occasionally there exist "text_copy_cb: operation failed" when executing
the bpf selftests, the reason is copy_to_kernel_nofault() failed and the
ecode of ESTAT register is 0x4 (PME: Page Modification Exception) due to
the pte is not writeable. The root cause is that there is another place
to set the pte entry as readonly which is in the generic weak version of
arch_protect_bpf_trampoline().
There are two ways to fix this race condition issue: the direct way is
to modify the generic weak arch_protect_bpf_trampoline() to add a mutex
lock for set_memory_rox(), but the other simple and proper way is to
just make arch_protect_bpf_trampoline() return 0 in the arch-specific
code because LoongArch has already use the BPF prog pack allocator for
trampoline.
Here are the trimmed kernel log messages:
copy_to_kernel_nofault: memory access failed, ecode 0x4
copy_to_kernel_nofault: the caller is text_copy_cb+0x50/0xa0
text_copy_cb: operation failed
------------[ cut here ]------------
bpf_prog_pack bug: missing bpf_arch_text_invalidate?
WARNING: kernel/bpf/core.c:1008 at bpf_prog_pack_free+0x200/0x228
...
Call Trace:
[<9000000000248914>] show_stack+0x64/0x188
[<9000000000241308>] dump_stack_lvl+0x6c/0x9c
[<90000000002705bc>] __warn+0x9c/0x200
[<9000000001c428c0>] __report_bug+0xa8/0x1c0
[<9000000001c42b5c>] report_bug+0x64/0x120
[<9000000001c7dcd0>] do_bp+0x270/0x3c0
[<9000000000246f40>] handle_bp+0x120/0x1c0
[<900000000047b030>] bpf_prog_pack_free+0x200/0x228
[<900000000047b2ec>] bpf_jit_binary_pack_free+0x24/0x60
[<900000000026989c>] bpf_jit_free+0x54/0xb0
[<900000000029e10c>] process_one_work+0x184/0x610
[<900000000029ef8c>] worker_thread+0x24c/0x388
[<90000000002a902c>] kthread+0x13c/0x170
[<9000000001c7dfe8>] ret_from_kernel_thread+0x28/0x1c0
[<9000000000246624>] ret_from_kernel_thread_asm+0xc/0x88
---[ end trace 0000000000000000 ]---
Here is a simple shell script to reproduce:
#!/bin/bash
for ((i=1; i<=1000; i++))
do
echo "Under testing $i ..."
dmesg -c > /dev/null
./test_progs -t fentry_attach_stress > /dev/null
dmesg -t | grep "text_copy_cb: operation failed"
if [ $? -eq 0 ]; then
break
fi
done
Cc: stable@vger.kernel.org
Fixes: 4ab17e762b ("LoongArch: BPF: Use BPF prog pack allocator")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
If copy_to_kernel_nofault() failed, no need to flush icache and just
return immediately.
Cc: stable@vger.kernel.org
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
set_memory_rw() and set_memory_rox() may fail, so we should check the
return values and return immediately in larch_insn_text_copy().
Cc: stable@vger.kernel.org
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
If memory access such as copy_{from, to}_kernel_nofault() failed, its
users do not know what happened, so it is very useful to print the
exception code for such cases. Furthermore, it is better to print the
caller function to know where is the entry.
Here are the low level call chains:
copy_from_kernel_nofault()
copy_from_kernel_nofault_loop()
__get_kernel_nofault()
copy_to_kernel_nofault()
copy_to_kernel_nofault_loop()
__put_kernel_nofault()
Cc: stable@vger.kernel.org
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Fix the warning:
BUG: using smp_processor_id() in preemptible [00000000] code: systemd/1
caller is larch_insn_text_copy+0x40/0xf0
Simply changing it to raw_smp_processor_id() is not enough: if preempt
and CPU hotplug happens after raw_smp_processor_id() but before calling
stop_machine(), the CPU where raw_smp_processor_id() has run may become
offline when stop_machine() and no CPU will run copy_to_kernel_nofault()
in text_copy_cb(). Thus guard the larch_insn_text_copy() calls with
cpus_read_lock() and change stop_machine() to stop_machine_cpuslocked()
to prevent this.
I've considered moving the locks inside larch_insn_text_copy() but
doing so seems not an easy hack. In bpf_arch_text_poke() obviously the
memcpy() call must be guarded by text_mutex, so we have to leave the
acquire of text_mutex out of larch_insn_text_copy(). But in the entire
kernel the acquire of mutexes is always after cpus_read_lock(), so we
cannot put cpus_read_lock() into larch_insn_text_copy() while leaving
the text_mutex acquire out (or we risk a deadlock due to inconsistent
lock acquire order). So let's fix the bug first and leave the posssible
refactor as future work.
Fixes: 9fbd18cf4c ("LoongArch: BPF: Add dynamic code modification support")
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The 128-bit atomic cmpxchg implementation uses the SC.Q instruction.
Older versions of GNU AS do not support that instruction, erroring out:
ERROR:root:{standard input}: Assembler messages:
{standard input}:4831: Error: no match insn: sc.q $t0,$t1,$r14
{standard input}:6407: Error: no match insn: sc.q $t0,$t1,$r23
{standard input}:10856: Error: no match insn: sc.q $t0,$t1,$r14
make[4]: *** [../scripts/Makefile.build:289: mm/slub.o] Error 1
(Binutils 2.41)
So test support for SC.Q in Kconfig and disable the atomics if the
instruction is not available.
Fixes: f0e4b1b6e2 ("LoongArch: Add 128-bit atomic cmpxchg support")
Closes: https://lore.kernel.org/lkml/20260216082834-edc51c46-7b7a-4295-8ea5-4d9a3ca2224f@linutronix.de/
Reviewed-by: Xi Ruoyao <xry111@xry111.site>
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Tested-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Customer reported that some of their krb5 mounts were failing against
a single server as the client was trying to mount the shares with
wrong credentials. It turned out the client was reusing SMB session
from first mount to try mounting the other shares, even though a
different username= option had been specified to the other mounts.
By using username mount option along with sec=krb5 to search for
principals from keytab is supported by cifs.upcall(8) since
cifs-utils-4.8. So fix this by matching username mount option in
match_session() even with Kerberos.
For example, the second mount below should fail with -ENOKEY as there
is no 'foobar' principal in keytab (/etc/krb5.keytab). The client
ends up reusing SMB session from first mount to perform the second
one, which is wrong.
```
$ ktutil
ktutil: add_entry -password -p testuser -k 1 -e aes256-cts
Password for testuser@ZELDA.TEST:
ktutil: write_kt /etc/krb5.keytab
ktutil: quit
$ klist -ke
Keytab name: FILE:/etc/krb5.keytab
KVNO Principal
---- ----------------------------------------------------------------
1 testuser@ZELDA.TEST (aes256-cts-hmac-sha1-96)
$ mount.cifs //w22-root2/scratch /mnt/1 -o sec=krb5,username=testuser
$ mount.cifs //w22-root2/scratch /mnt/2 -o sec=krb5,username=foobar
$ mount -t cifs | grep -Po 'username=\K\w+'
testuser
testuser
```
Reported-by: Oscar Santos <ossantos@redhat.com>
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Cc: David Howells <dhowells@redhat.com>
Cc: linux-cifs@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
ctlr is allocated using devm_spi_alloc_host(), which automatically
handles reference counting via the devm framework.
Calling spi_controller_put() manually in the probe error path is
redundant and results in a double-free.
Fixes: e75a6b00ad ("spi: axiado: Add driver for Axiado SPI DB controller")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260302-axiado-v1-1-1132819f1cb7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an ACP70 SoundWire machine entry for ASUS PX13
(HN7306EA/HN7306EAC) with rt721 and two TAS2783 amps on link1.
Describe rt721 with jack/DMIC endpoints on this platform and add
explicit left/right TAS2783 speaker endpoint mapping via name prefixes.
Signed-off-by: Hasun Park <hasunpark@gmail.com>
Link: https://patch.msgid.link/20260308151654.29059-3-hasunpark@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some ASUS ProArt PX13 systems expose ACP ACPI config flags that can
select a non-working fallback path.
Add a DMI override in snd_amd_acp_find_config() for ACP70+ boards and
return 0 so ACP ACPI flag-based selection is skipped on this platform.
This keeps machine driver selection on the intended SoundWire path.
Signed-off-by: Hasun Park <hasunpark@gmail.com>
Link: https://patch.msgid.link/20260308151654.29059-2-hasunpark@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A previous change added NULL checks and cleanup for allocation
failures in sma1307_setting_loaded().
However, the cleanup for mode_set entries is wrong. Those entries are
allocated with devm_kzalloc(), so they are device-managed resources and
must not be freed with kfree(). Manually freeing them in the error path
can lead to a double free when devres later releases the same memory.
Drop the manual kfree() loop and let devres handle the cleanup.
Fixes: 0ec6bd1670 ("ASoC: sma1307: Add NULL check in sma1307_setting_loaded()")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260313040611.391479-1-lgs201920130244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In aml_spisg_probe(), ctlr is allocated by
spi_alloc_target()/spi_alloc_host(), but fails to call
spi_controller_put() in several error paths. This leads
to a memory leak whenever the driver fails to probe after
the initial allocation.
Convert to use devm_spi_alloc_host()/devm_spi_alloc_target()
to fix the memory leak.
Fixes: cef9991e04 ("spi: Add Amlogic SPISG driver")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260308-spisg-v1-1-2cace5cafc24@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses devm_clk_get_enabled() which enables the clock and
registers a callback to automatically disable it when the device
is unbound.
Remove the redundant aml_sfc_disable_clk() call in the error paths
and remove callback.
Fixes: 4670db6f32 ("spi: amlogic: add driver for Amlogic SPI Flash Controller")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260308-spifc-a4-1-v1-1-77e286c26832@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The one core change is a re-roll of the tag allocation fix from the
last pull request that uses the correct goto to unroll all the
allocations. The remianing fixes are all small ones in drivers.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCabbZ8xsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIW4hAEAyEbXcyUa4tNTsQfRPeJitgq4WDyPDv83
lnAvY/J5IEoBAJel9hRJ8lJfwziXVhMsxU3XHSXqQdA22N8tS7n4gTtq
=IGTE
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The one core change is a re-roll of the tag allocation fix from the
last pull request that uses the correct goto to unroll all the
allocations. The remianing fixes are all small ones in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hisi_sas: Fix NULL pointer exception during user_scan()
scsi: qla2xxx: Completely fix fcport double free
scsi: ufs: core: Fix SError in ufshcd_rtc_work() during UFS suspend
scsi: core: Fix error handling for scsi_alloc_sdev()
- kprobes: avoid crash when rmmod/insmod after ftrace killed
This fixes a kernel crash caused by kprobes on the symbol in a
module which is unloaded after ftrace_kill() is called.
- kprobes: Remove unneeded warnings from __arm_kprobe_ftrace()
Remove unneeded WARN messages which can be kicked if the kprobe is
using ftrace and it fails to enable the ftrace. Since kprobes
correctly handle such failure, we don't need to warn it.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmm2hk8bHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bBZkH+gP3OllhdIU3AUB+vXEb
UEE3VE5IZRufSgtjbbJnYI3b8U2dWXw7wmb+fBJ0i0Zf6F+2IUr3hUg1pHNARvlL
MMu1YW7PG8gKGUsNc7jpHBVXrnefA4XpzXe7wtxaGvqAV16nL/6xhZlanGgL50Gv
+F9cETMIGZ8duF6XVgEMmUUCg88Iwpp9MjzDQOjpRK7z41LND3ccJ2V88ODzDevj
idnRbnk12Q9b7xZwGL5P5Ab163kHPFExsXQQnPmy/0fLcyGi8U3hY5EwYhOT85J0
qRZVHpR1yrXqBpaxD/7as5/pfuUluxdzwmDkyRuQGYW6y7xkhlVNEGWqsWZeYLuW
IZU=
=Zkm3
-----END PGP SIGNATURE-----
Merge tag 'probes-fixes-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- Avoid crash when rmmod/insmod after ftrace killed
This fixes a kernel crash caused by kprobes on the symbol in a module
which is unloaded after ftrace_kill() is called.
- Remove unneeded warnings from __arm_kprobe_ftrace()
Remove unneeded WARN messages which can be triggered if the kprobe is
using ftrace and it fails to enable the ftrace. Since kprobes
correctly handle such failure, we don't need to warn it.
* tag 'probes-fixes-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
kprobes: Remove unneeded warnings from __arm_kprobe_ftrace()
kprobes: avoid crash when rmmod/insmod after ftrace killed
- lib/bootconfig: fix off-by-one in xbc_verify_tree() unclosed brace
error; This fixes a wrong error place in unclosed brace error
message.
- lib/bootconfig: check bounds before writing in __xbc_open_brace();
This fixes to check the array index before setting array, so that
the bootconfig can support 16th-depth nested brace correctly.
- lib/bootconfig: fix snprintf truncation check in
xbc_node_compose_key_after(); This fixes to handle the return
value of snprintf() correctly in case of the return value ==
size.
- bootconfig: Add bootconfig tests about braces
Add test cases for checking error position about unclosed brace
and ensuring supporting 16th depth nested braces correctly.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmmz2oUbHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bVUsH/RZ1L9qQzbUH5gFtnKuP
cv8R84lVOf9+Yg9H+RCT689qCOTtLIVuK6LaDCChhbeiaF05hXIvRu0Dr1WmVrxc
O7ur1LucRNbEsB2O2UCWZjW1SBbNa9zvgaYGMFhBbkViGUUfj9uJgyn5zin0A6Pl
nwHuN3BNqEmR2aayikdLESwJ3IBYyrtPWg0/lBT+Dy5lcnh6h5+2HP1u70W3i7+c
4psAqA0A+a1nY9yQD+tw8kzUb8ZXgyTrkGkWECRkb/M7K843X/Csi64GYCGNlmuw
FXcIwxgGk5X3yQgDOoPHB6sBB7Cgo6jokxUJwrCiJintZJEQj5Ryzun8FmAi9vvO
NmU=
=15kg
-----END PGP SIGNATURE-----
Merge tag 'bootconfig-fixes-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bootconfig fixes from Masami Hiramatsu:
- fix off-by-one in xbc_verify_tree() unclosed brace error. This fixes
a wrong error place in unclosed brace error message
- check bounds before writing in __xbc_open_brace(). This fixes to
check the array index before setting array, so that the bootconfig
can support 16th-depth nested brace correctly
- fix snprintf truncation check in xbc_node_compose_key_after(). This
fixes to handle the return value of snprintf() correctly in case of
the return value == size
- Add bootconfig tests about braces Add test cases for checking error
position about unclosed brace and ensuring supporting 16th depth
nested braces correctly
* tag 'bootconfig-fixes-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
bootconfig: Add bootconfig tests about braces
lib/bootconfig: fix snprintf truncation check in xbc_node_compose_key_after()
lib/bootconfig: check bounds before writing in __xbc_open_brace()
lib/bootconfig: fix off-by-one in xbc_verify_tree() unclosed brace error
- Correctly handle deeactivation of interrupts that were activated from
LRs. Since EOIcount only denotes deactivation of interrupts that
are not present in an LR, start EOIcount deactivation walk *after*
the last irq that made it into an LR.
- Avoid calling into the stubs to probe for ICH_VTR_EL2.TDS when
pKVM is already enabled -- not only thhis isn't possible (pKVM
will reject the call), but it is also useless: this can only
happen for a CPU that has already booted once, and the capability
will not change.
- Fix a couple of low-severity bugs in our S2 fault handling path,
affecting the recently introduced LS64 handling and the even more
esoteric handling of hwpoison in a nested context
- Address yet another syzkaller finding in the vgic initialisation,
where we would end-up destroying an uninitialised vgic with nasty
consequences
- Address an annoying case of pKVM failing to boot when some of the
memblock regions that the host is faulting in are not page-aligned
- Inject some sanity in the NV stage-2 walker by checking the limits
against the advertised PA size, and correctly report the resulting
faults
PPC:
- Fix a PPC e500 build error due to a long-standing wart that was exposed by
the recent conversion to kmalloc_obj(); rip out all the ugliness that
led to the wart.
RISC-V:
- Prevent speculative out-of-bounds access using array_index_nospec()
in APLIC interrupt handling, ONE_REG regiser access, AIA CSR access,
float register access, and PMU counter access
- Fix potential use-after-free issues in kvm_riscv_gstage_get_leaf(),
kvm_riscv_aia_aplic_has_attr(), and kvm_riscv_aia_imsic_has_attr()
- Fix potential null pointer dereference in kvm_riscv_vcpu_aia_rmw_topei()
- Fix off-by-one array access in SBI PMU
- Skip THP support check during dirty logging
- Fix error code returned for Smstateen and Ssaia ONE_REG interface
- Check host Ssaia extension when creating AIA irqchip
x86:
- Fix cases where CPUID mitigation features were incorrectly marked as
available whenever the kernel used scattered feature words for them.
- Validate _all_ GVAs, rather than just the first GVA, when processing
a range of GVAs for Hyper-V's TLB flush hypercalls.
- Fix a brown paper bug in add_atomic_switch_msr().
- Use hlist_for_each_entry_srcu() when traversing mask_notifier_list,
to fix a lockdep warning; KVM doesn't hold RCU, just irq_srcu.
- Ensure AVIC VMCB fields are initialized if the VM has an in-kernel local
APIC (and AVIC is enabled at the module level).
- Update CR8 write interception when AVIC is (de)activated, to fix a bug
where the guest can run in perpetuity with the CR8 intercept enabled.
- Add a quirk to skip the consistency check on FREEZE_IN_SMM, i.e. to allow
L1 hypervisors to set FREEZE_IN_SMM. This reverts (by default) an
unintentional tightening of userspace ABI in 6.17, and provides some
amount of backwards compatibility with hypervisors who want to freeze
PMCs on VM-Entry.
- Validate the VMCS/VMCB on return to a nested guest from SMM, because
either userspace or the guest could stash invalid values in memory
and trigger the processor's consistency checks.
Generic:
- Remove a subtle pseudo-overlay of kvm_stats_desc, which, aside from being
unnecessary and confusing, triggered compiler warnings due to
-Wflex-array-member-not-at-end.
- Document that vcpu->mutex is take outside of kvm->slots_lock and
kvm->slots_arch_lock, which is intentional and desirable despite being
rather unintuitive.
Selftests:
- Increase the maximum number of NUMA nodes in the guest_memfd selftest to
64 (from 8).
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmmy6n8UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNX7ggAhWoCG+AE6P3yrp6Mi+nRYpeRGC3q
q2IiZCn0UoCg6q3c2kgn7b/N2zLJs0Q8FZRCEp2Je+2uvptpmdp/BMEfiIU3n2/a
61z+Dydbpyc+kUmhJzUJ+aotq5FnMNmAAmqSKoc19GhAx2OQhQmBP/JOZ0P/eqLE
Is0qNBgr/Zms2ib3GFf/JT+urysL2mX47qe92HTzq1T9EEG0KleID0Jz8vYQI8Fr
I5N9+lTxagQDi8ytwOM85Cn8K7wh+CQIgzmciHcVErpAvAWkrEjrPlQltpEz2C5B
aWEcRgw46utEaAiwPQGJRW6TeoKUG0pUR3v6T90nBkjjJ1npm6gPVE6TBA==
=7nQ9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Quite a large pull request, partly due to skipping last week and
therefore having material from ~all submaintainers in this one. About
a fourth of it is a new selftest, and a couple more changes are large
in number of files touched (fixing a -Wflex-array-member-not-at-end
compiler warning) or lines changed (reformatting of a table in the API
documentation, thanks rST).
But who am I kidding---it's a lot of commits and there are a lot of
bugs being fixed here, some of them on the nastier side like the
RISC-V ones.
ARM:
- Correctly handle deactivation of interrupts that were activated
from LRs. Since EOIcount only denotes deactivation of interrupts
that are not present in an LR, start EOIcount deactivation walk
*after* the last irq that made it into an LR
- Avoid calling into the stubs to probe for ICH_VTR_EL2.TDS when pKVM
is already enabled -- not only thhis isn't possible (pKVM will
reject the call), but it is also useless: this can only happen for
a CPU that has already booted once, and the capability will not
change
- Fix a couple of low-severity bugs in our S2 fault handling path,
affecting the recently introduced LS64 handling and the even more
esoteric handling of hwpoison in a nested context
- Address yet another syzkaller finding in the vgic initialisation,
where we would end-up destroying an uninitialised vgic with nasty
consequences
- Address an annoying case of pKVM failing to boot when some of the
memblock regions that the host is faulting in are not page-aligned
- Inject some sanity in the NV stage-2 walker by checking the limits
against the advertised PA size, and correctly report the resulting
faults
PPC:
- Fix a PPC e500 build error due to a long-standing wart that was
exposed by the recent conversion to kmalloc_obj(); rip out all the
ugliness that led to the wart
RISC-V:
- Prevent speculative out-of-bounds access using array_index_nospec()
in APLIC interrupt handling, ONE_REG regiser access, AIA CSR
access, float register access, and PMU counter access
- Fix potential use-after-free issues in kvm_riscv_gstage_get_leaf(),
kvm_riscv_aia_aplic_has_attr(), and kvm_riscv_aia_imsic_has_attr()
- Fix potential null pointer dereference in
kvm_riscv_vcpu_aia_rmw_topei()
- Fix off-by-one array access in SBI PMU
- Skip THP support check during dirty logging
- Fix error code returned for Smstateen and Ssaia ONE_REG interface
- Check host Ssaia extension when creating AIA irqchip
x86:
- Fix cases where CPUID mitigation features were incorrectly marked
as available whenever the kernel used scattered feature words for
them
- Validate _all_ GVAs, rather than just the first GVA, when
processing a range of GVAs for Hyper-V's TLB flush hypercalls
- Fix a brown paper bug in add_atomic_switch_msr()
- Use hlist_for_each_entry_srcu() when traversing mask_notifier_list,
to fix a lockdep warning; KVM doesn't hold RCU, just irq_srcu
- Ensure AVIC VMCB fields are initialized if the VM has an in-kernel
local APIC (and AVIC is enabled at the module level)
- Update CR8 write interception when AVIC is (de)activated, to fix a
bug where the guest can run in perpetuity with the CR8 intercept
enabled
- Add a quirk to skip the consistency check on FREEZE_IN_SMM, i.e. to
allow L1 hypervisors to set FREEZE_IN_SMM. This reverts (by
default) an unintentional tightening of userspace ABI in 6.17, and
provides some amount of backwards compatibility with hypervisors
who want to freeze PMCs on VM-Entry
- Validate the VMCS/VMCB on return to a nested guest from SMM,
because either userspace or the guest could stash invalid values in
memory and trigger the processor's consistency checks
Generic:
- Remove a subtle pseudo-overlay of kvm_stats_desc, which, aside from
being unnecessary and confusing, triggered compiler warnings due to
-Wflex-array-member-not-at-end
- Document that vcpu->mutex is take outside of kvm->slots_lock and
kvm->slots_arch_lock, which is intentional and desirable despite
being rather unintuitive
Selftests:
- Increase the maximum number of NUMA nodes in the guest_memfd
selftest to 64 (from 8)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (43 commits)
KVM: selftests: Verify SEV+ guests can read and write EFER, CR0, CR4, and CR8
Documentation: kvm: fix formatting of the quirks table
KVM: x86: clarify leave_smm() return value
selftests: kvm: add a test that VMX validates controls on RSM
selftests: kvm: extract common functionality out of smm_test.c
KVM: SVM: check validity of VMCB controls when returning from SMM
KVM: VMX: check validity of VMCS controls when returning from SMM
KVM: SVM: Set/clear CR8 write interception when AVIC is (de)activated
KVM: SVM: Initialize AVIC VMCB fields if AVIC is enabled with in-kernel APIC
KVM: x86: Introduce KVM_X86_QUIRK_VMCS12_ALLOW_FREEZE_IN_SMM
KVM: x86: Fix SRCU list traversal in kvm_fire_mask_notifiers()
KVM: VMX: Fix a wrong MSR update in add_atomic_switch_msr()
KVM: x86: hyper-v: Validate all GVAs during PV TLB flush
KVM: x86: synthesize CPUID bits only if CPU capability is set
KVM: PPC: e500: Rip out "struct tlbe_ref"
KVM: PPC: e500: Fix build error due to using kmalloc_obj() with wrong type
KVM: selftests: Increase 'maxnode' for guest_memfd tests
KVM: arm64: pkvm: Don't reprobe for ICH_VTR_EL2.TDS on CPU hotplug
KVM: arm64: vgic: Pick EOIcount deactivations from AP-list tail
KVM: arm64: Remove the redundant ISB in __kvm_at_s1e2()
...
the x2apic hardware while it was disabled by the kernel.
Force-disable it again and issue a warning into the syslog.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=VNhj
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Work around S2RAM hang if the firmware unexpectedly re-enables the
x2apic hardware while it was disabled by the kernel.
Force-disable it again and issue a warning into the syslog"
* tag 'x86-urgent-2026-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Disable x2apic on resume if the kernel expects so
- Fix CID hangs due to a race between concurrent forks
- Fix vfork()/CLONE_VM MMCID bug causing hangs
- Remove pointless preemption guard
- Fix CID task list walk performance regression on large systems
by removing the known-flaky and slow counting logic using
for_each_process_thread() in mm_cid_*fixup_tasks_to_cpus(),
and implementing a simple sched_mm_cid::node list instead
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ce5G
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2026-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"More MM-CID fixes, mostly fixing hangs/races:
- Fix CID hangs due to a race between concurrent forks
- Fix vfork()/CLONE_VM MMCID bug causing hangs
- Remove pointless preemption guard
- Fix CID task list walk performance regression on large systems
by removing the known-flaky and slow counting logic using
for_each_process_thread() in mm_cid_*fixup_tasks_to_cpus(), and
implementing a simple sched_mm_cid::node list instead"
* tag 'sched-urgent-2026-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/mmcid: Avoid full tasklist walks
sched/mmcid: Remove pointless preempt guard
sched/mmcid: Handle vfork()/CLONE_VM correctly
sched/mmcid: Prevent CID stalls due to concurrent forks
Our vcpu reset suffers from a particularly interesting flaw, as it
does not correctly deal with state that will have an effect on the
execution flow out of reset.
Take the following completely random example, never seen in the wild
and that never resulted in a couple of sleepless nights: /s
- vcpu-A issues a PSCI_CPU_OFF using the SMC conduit
- SMC being a trapped instruction (as opposed to HVC which is always
normally executed), we annotate the vcpu as needing to skip the
next instruction, which is the SMC itself
- vcpu-A is now safely off
- vcpu-B issues a PSCI_CPU_ON for vcpu-A, providing a starting PC
- vcpu-A gets reset, get the new PC, and is sent on its merry way
- right at the point of entering the guest, we notice that a PC
increment is pending (remember the earlier SMC?)
- vcpu-A skips its first instruction...
What could possibly go wrong?
Well, I'm glad you asked. For pKVM as a NV guest, that first instruction
is extremely significant, as it indicates whether the CPU is booting
or resuming. Having skipped that instruction, nothing makes any sense
anymore, and CPU hotplugging fails.
This is all caused by the decoupling of PC update from the handling
of an exception that triggers such update, making it non-obvious
what affects what when.
Fix this train wreck by discarding all the PC-affecting state on
vcpu reset.
Fixes: f5e3068061 ("KVM: arm64: Move __adjust_pc out of line")
Cc: stable@vger.kernel.org
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Link: https://patch.msgid.link/20260312140850.822968-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
The assembly flush instructions were swapped for I- and D-cache flags:
SYSCALL_DEFINE3(cacheflush, ...)
{
if (cache & DCACHE) {
"fic ...\n"
}
if (cache & ICACHE && error == 0) {
"fdc ...\n"
}
Fix it by using fdc for DCACHE, and fic for ICACHE flushing.
Reported-by: Felix Lechner <felix.lechner@lease-up.com>
Fixes: c6d96328fe ("parisc: Add cacheflush() syscall")
Cc: <stable@vger.kernel.org> # v6.5+
Signed-off-by: Helge Deller <deller@gmx.de>
Subsystem:
- simplify combined i3c/i2c dependencies
Drivers:
- dw: handle 2C properly, fix possible race condition
- mipi-i3c-hci: many DMA related fixes
-----BEGIN PGP SIGNATURE-----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=Ojo2
-----END PGP SIGNATURE-----
Merge tag 'i3c/fixes-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c fixes from Alexandre Belloni:
"This introduces the I3C_OR_I2C symbol which is not a fix per se but is
affecting multiple subsystems so it is included to ease
synchronization.
Apart from that, Adrian is mostly fixing the mipi-i3c-hci driver DMA
handling, and I took the opportunity to add two fixes for the dw-i3c
driver.
Subsystem:
- simplify combined i3c/i2c dependencies
Drivers:
- dw: handle 2C properly, fix possible race condition
- mipi-i3c-hci: many DMA related fixes"
* tag 'i3c/fixes-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: dw-i3c-master: Set SIR_REJECT in DAT on device attach and reattach
i3c: master: dw-i3c: Fix missing of_node for virtual I2C adapter
i3c: mipi-i3c-hci: Fallback to software reset when bus disable fails
i3c: mipi-i3c-hci: Fix handling of shared IRQs during early initialization
i3c: mipi-i3c-hci: Fix race in DMA error handling in interrupt context
i3c: mipi-i3c-hci: Consolidate common xfer processing logic
i3c: mipi-i3c-hci: Restart DMA ring correctly after dequeue abort
i3c: mipi-i3c-hci: Add missing TID field to no-op command descriptor
i3c: mipi-i3c-hci: Correct RING_CTRL_ABORT handling in DMA dequeue
i3c: mipi-i3c-hci: Fix race between DMA ring dequeue and interrupt handler
i3c: mipi-i3c-hci: Fix race in DMA ring dequeue
i3c: mipi-i3c-hci: Fix race in DMA ring enqueue for parallel xfers
i3c: mipi-i3c-hci: Consolidate spinlocks
i3c: mipi-i3c-hci: Factor out DMA mapping from queuing path
i3c: mipi-i3c-hci: Fix Hot-Join NACK
i3c: mipi-i3c-hci: Use ETIMEDOUT instead of ETIME for timeout errors
i3c: simplify combined i3c/i2c dependencies
Toolchain and infrastructure:
- Remap paths to avoid absolute ones starting with the upcoming Rust
1.95.0 release. This improves build reproducibility, avoids leaking
the exact path and avoids having the same path appear in two forms.
The approach here avoids remapping debug information as well, in
order to avoid breaking tools that used the paths to access source
files, which was the previous attempt that needed to be reverted.
- Allow 'unused_features' lint for the upcoming Rust 1.96.0 release.
While well-intentioned, we do not benefit much from the new lint.
- Emit dependency information into '$(depfile)' directly to avoid
a temporary '.d' file (it was an old approach).
'kernel' crate:
- 'str' module: fix warning under '!CONFIG_BLOCK' by making
'NullTerminatedFormatter' public.
- 'cpufreq' module: suppress false positive Clippy warning.
'pin-init' crate:
- Remove '#[disable_initialized_field_access]' attribute which was
unsound. This means removing the support for structs with unaligned
fields (through the 'repr(packed)' attribute), for now.
And document the load-bearing fact of field accessors (i.e. that they
are required for soundness).
- Replace shadowed return token by 'unsafe'-to-create token in order
to remain sound in the face of the likely upcoming Type Alias Impl
Trait (TAIT) and the next trait solver in upstream Rust.
-----BEGIN PGP SIGNATURE-----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=7LgC
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull Rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Remap paths to avoid absolute ones starting with the upcoming Rust
1.95.0 release. This improves build reproducibility, avoids leaking
the exact path and avoids having the same path appear in two forms
The approach here avoids remapping debug information as well, in
order to avoid breaking tools that used the paths to access source
files, which was the previous attempt that needed to be reverted
- Allow 'unused_features' lint for the upcoming Rust 1.96.0 release.
While well-intentioned, we do not benefit much from the new lint
- Emit dependency information into '$(depfile)' directly to avoid a
temporary '.d' file (it was an old approach)
'kernel' crate:
- 'str' module: fix warning under '!CONFIG_BLOCK' by making
'NullTerminatedFormatter' public
- 'cpufreq' module: suppress false positive Clippy warning
'pin-init' crate:
- Remove '#[disable_initialized_field_access]' attribute which was
unsound. This means removing the support for structs with unaligned
fields (through the 'repr(packed)' attribute), for now
And document the load-bearing fact of field accessors (i.e. that
they are required for soundness)
- Replace shadowed return token by 'unsafe'-to-create token in order
to remain sound in the face of the likely upcoming Type Alias Impl
Trait (TAIT) and the next trait solver in upstream Rust"
* tag 'rust-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: kbuild: allow `unused_features`
rust: cpufreq: suppress clippy::double_parens in Policy doctest
rust: pin-init: replace shadowed return token by `unsafe`-to-create token
rust: pin-init: internal: init: document load-bearing fact of field accessors
rust: pin-init: internal: init: remove `#[disable_initialized_field_access]`
rust: build: remap path to avoid absolute path
rust: kbuild: emit dep-info into $(depfile) directly
rust: str: make NullTerminatedFormatter public
Kevin Hao says:
====================
net: macb: Fix Ethernet malfunction on AMD Versal board after suspend
On Versal boards, the tx/rx queue pointer registers are cleared after suspend,
which causes Ethernet malfunction. This patch series addresses this issue by
reinitializing the tx/rx queue pointer registers and the rx ring.
====================
Link: https://patch.msgid.link/20260312-macb-versal-v1-0-467647173fa4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On certain platforms, such as AMD Versal boards, the tx/rx queue pointer
registers are cleared after suspend, and the rx queue pointer register
is also disabled during suspend if WOL is enabled. Previously, we assumed
that these registers would be restored by macb_mac_link_up(). However,
in commit bf9cf80cab, macb_init_buffers() was moved from
macb_mac_link_up() to macb_open(). Therefore, we should call
macb_init_buffers() to reinitialize the tx/rx queue pointer registers
during resume.
Due to the reset of these two registers, we also need to adjust the
tx/rx rings accordingly. The tx ring will be handled by
gem_shuffle_tx_rings() in macb_mac_link_up(), so we only need to
initialize the rx ring here.
Fixes: bf9cf80cab ("net: macb: Fix tx/rx malfunction after phy link down and up")
Reported-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Quanyang Wang <quanyang.wang@windriver.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260312-macb-versal-v1-2-467647173fa4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the initialization code for the GEM RX ring into a new function.
This change will be utilized in a subsequent patch. No functional changes
are introduced.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260312-macb-versal-v1-1-467647173fa4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Page recycling was removed from the XDP_DROP path in emac_run_xdp() to
avoid conflicts with AF_XDP zero-copy mode, which uses xsk_buff_free()
instead.
However, this causes a memory leak when running XDP programs that drop
packets in non-zero-copy mode (standard page pool mode). The pages are
never returned to the page pool, leading to OOM conditions.
Fix this by handling cleanup in the caller, emac_rx_packet().
When emac_run_xdp() returns ICSSG_XDP_CONSUMED for XDP_DROP, the
caller now recycles the page back to the page pool. The zero-copy
path, emac_rx_packet_zc() already handles cleanup correctly with
xsk_buff_free().
Fixes: 7a64bb388d ("net: ti: icssg-prueth: Add AF_XDP zero copy for RX")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260311095441.1691636-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For Zhaoxin processors, the XSHA1 instruction requires the total memory
allocated at %rdi register must be 32 bytes, while the XSHA1 and
XSHA256 instruction doesn't perform any operation when %ecx is zero.
Due to these requirements, the current padlock-sha driver does not work
correctly with Zhaoxin processors. It cannot pass the self-tests and
therefore does not activate the driver on Zhaoxin processors. This issue
has been reported in Debian [1]. The self-tests fail with the
following messages [2]:
alg: shash: sha1-padlock-nano test failed (wrong result) on test vector 0, cfg="init+update+final aligned buffer"
alg: self-tests for sha1 using sha1-padlock-nano failed (rc=-22)
alg: shash: sha256-padlock-nano test failed (wrong result) on test vector 0, cfg="init+update+final aligned buffer"
alg: self-tests for sha256 using sha256-padlock-nano failed (rc=-22)
Disable the padlock-sha driver on Zhaoxin processors with the CPU family
0x07 and newer. Following the suggestion in [3], support for PHE will be
added to lib/crypto/ instead.
[1] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1113996
[2] https://linux-hardware.org/?probe=271fabb7a4&log=dmesg
[3] https://lore.kernel.org/linux-crypto/aUI4CGp6kK7mxgEr@gondor.apana.org.au/
Fixes: 63dc06cd12 ("crypto: padlock-sha - Use API partial block handling")
Cc: stable@vger.kernel.org
Signed-off-by: AlanSong-oc <AlanSong-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20260313080150.9393-2-AlanSong-oc@zhaoxin.com
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
A potential race condition exists in mana_hwc_destroy_channel() where
hwc->caller_ctx is freed before the HWC's Completion Queue (CQ) and
Event Queue (EQ) are destroyed. This allows an in-flight CQ interrupt
handler to dereference freed memory, leading to a use-after-free or
NULL pointer dereference in mana_hwc_handle_resp().
mana_smc_teardown_hwc() signals the hardware to stop but does not
synchronize against IRQ handlers already executing on other CPUs. The
IRQ synchronization only happens in mana_hwc_destroy_cq() via
mana_gd_destroy_eq() -> mana_gd_deregister_irq(). Since this runs
after kfree(hwc->caller_ctx), a concurrent mana_hwc_rx_event_handler()
can dereference freed caller_ctx (and rxq->msg_buf) in
mana_hwc_handle_resp().
Fix this by reordering teardown to reverse-of-creation order: destroy
the TX/RX work queues and CQ/EQ before freeing hwc->caller_ctx. This
ensures all in-flight interrupt handlers complete before the memory they
access is freed.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/abHA3AjNtqa1nx9k@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
