disable clock and correct sequence when unload
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
correct the sequence when unload this module
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ssc private data has been set in ssc driver, this cause the error
private data set to ssc, remove it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When build as module, it reports following error, using this patch
fix it
sound/soc/atmel/atmel-pcm-pdc.c:387: error: redefinition of 'atmel_pcm_pdc_platform_register'
sound/soc/atmel/atmel-pcm.h:95: note: previous definition of 'atmel_pcm_pdc_platform_register' was here
sound/soc/atmel/atmel-pcm-pdc.c:393: error: redefinition of 'atmel_pcm_pdc_platform_unregister'
sound/soc/atmel/atmel-pcm.h:99: note: previous definition of 'atmel_pcm_pdc_platform_unregister' was here
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since header mach/regs-mem.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since header mach/regs-power.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since header mach/regs-s3c2412-mem.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix drift in DT parsing function name in the stub code.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously arizona_calc_fll() was checking if the target frequency is
exactly divisible by reference frequency, but should have been product
of the ratio and the reference frequency.
Also scale down the Lamba and Theta coefficients be under 16-bits in
order to match the registers.
Signed-off-by: Ryo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
ip_eth_mc_map function can't be used when CONFIG_INET isn't defined.
Fixed compilation error by adding CONFIG_INET define check before using the
function.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate return value of mlx4_en_ethtool_add_mac_rule_by_ipv4 in case of
failure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the loop, don't check 'rv' twice in a row. Without the loop, 'rv'
doesn't even need to be checked.
Make the comment more grammar-friendly.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in del_timer() there has already placed a timer_pending() function
to check whether the timer to be deleted is pending or not, it's
unnecessary to check timer pending state again before del_timer() is
called.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the PF driver is unloaded and re-loaded while VFs are attached
to VMs, it loses control of its VFs.
The PF driver now uses the newly defined/created GET_IFACE_LIST cmd
(available in FW ver >= 4.6) to query the if_id of the VFs
(enabled in its previous life). The PF driver then uses the if_id for
further VF configuration.
The GET_IFACE_MAC_LIST cmd has also implemented in BE3 FW for PF to
query pmac-ids used by its VFs.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Hoist assigns from if tests.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems due to RCU usage, i.e. within SCTP's address binding list,
a, say, ``behavioral change'' was introduced which does actually
not conform to the RFC anymore. In particular consider the following
(fictional) scenario to demonstrate this:
do:
Two SOCK_SEQPACKET-style sockets are opened (S1, S2)
S1 is bound to 127.0.0.1, port 1024 [server]
S2 is bound to 127.0.0.1, port 1025 [client]
listen(2) is invoked on S1
From S2 we call one sendmsg(2) with msg.msg_name and
msg.msg_namelen parameters set to the server's
address
S1, S2 are closed
goto do
The first pass of this loop passes successful, while the second round
fails during binding of S1 (address still in use). What is happening?
In the first round, the initial handshake is being done, and, at the
time close(2) is called on S1, a non-graceful shutdown is performed via
ABORT since in S1's receive queue an unprocessed packet is present,
thus stating an error condition. This can be considered as a correct
behavior.
During close also all bound addresses are freed, thus nothing *must*
be active anymore. In reference to RFC2960:
After checking the Verification Tag, the receiving endpoint shall
remove the association from its record, and shall report the
termination to its upper layer. (9.1 Abort of an Association)
Also, no half-open states are supported, thus after an ungraceful
shutdown, we leave nothing behind. However, this seems not to be
happening though. In a real-world scenario, this is exactly where
it breaks the lksctp-tools functional test suite, *for instance*:
./test_sockopt
test_sockopt.c 1 PASS : getsockopt(SCTP_STATUS) on a socket with no assoc
test_sockopt.c 2 PASS : getsockopt(SCTP_STATUS)
test_sockopt.c 3 PASS : getsockopt(SCTP_STATUS) with invalid associd
test_sockopt.c 4 PASS : getsockopt(SCTP_STATUS) with NULL associd
test_sockopt.c 5 BROK : bind: Address already in use
The underlying problem is that sctp_endpoint_destroy() hasn't been
triggered yet while the next bind attempt is being done. It will be
triggered eventually (but too late) by sctp_transport_destroy_rcu()
after one RCU grace period:
sctp_transport_destroy()
sctp_transport_destroy_rcu() ----.
sctp_association_put() [*] <--+--> sctp_packet_free()
sctp_association_destroy() [...]
sctp_endpoint_put() skb->destructor
sctp_endpoint_destroy() sctp_wfree()
sctp_bind_addr_free() sctp_association_put() [*]
Thus, we move out the condition with sctp_association_put() as well as
the sctp_packet_free() invocation and the issue can be solved. We also
better free the SCTP chunks first before putting the ref of the association.
With this patch, the example above (which simulates a similar scenario
as in the implementation of this test case) and therefore also the test
suite run successfully through. Tested by myself.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the fields must be null-terminated:
the caller may use it as null-terminted string, next.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
reduce the permission check of bond device's ioctl.
allow the userns root to control the bond device.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since the mdb table is belong to bridge device,and the
bridge device can only be seen in one netns.
So it's safe to allow unprivileged user which is the
creator of userns and netns to modify the mdb table.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ebt_table is a private resource of netns, operating ebtables
in one netns will not affect other netns, we can allow the
creator user of userns and netns to change the ebtables.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now,only ixgdb,macvlan,vxlan and bridge implement
fdb_add/fdb_del operations.
these operations only operate the private data of net
device. So allowing the unprivileged users who creates
the userns and netns to add/del fdb entries will do no
harm to other netns.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is normal for minidrivers accumulating frames to return NULL
from their tx_fixup function. We do not want to count this as a
drop, or log any debug messages. A different exit path is
therefore chosen for such drivers, skipping the debug message
and the tx_dropped increment.
The test for accumulating drivers was however completely bogus,
making the exit path selection depend on whether the user had
enabled tx_err logging or not. This would arbitrarily mess up
accounting for both accumulating and non-accumulating minidrivers,
and would result in unwanted debug messages for the accumulating
drivers.
Fix by testing for FLAG_MULTI_PACKET instead, which probably was
the intention from the beginning. This usage match the documented
behaviour of this flag:
Indicates to usbnet, that USB driver accumulates multiple IP packets.
Affects statistic (counters) and short packet handling.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates LINUX_MIB_LISTENDROPS and LINUX_MIB_LISTENOVERFLOWS in
tcp_v6_conn_request() and tcp_v6_err(). tcp_v6_conn_request() in particular can
drop SYNs for various reasons which are not currently tracked.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates LINUX_MIB_LISTENDROPS in tcp_v4_conn_request() and
tcp_v4_err(). tcp_v4_conn_request() in particular can drop SYNs for various
reasons which are not currently tracked.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of annotating with a comment, add a lockdep
annotation which also serves as documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver determined the connection was lost or that
it couldn't securely maintain the connection when coming
out of WoWLAN, send a deauth frame to the AP to also let
it know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we had a connection for WoWLAN and after resume it
needed to be disconnected, the previous commit enabled
sending a deauth frame to the AP. This frame would not
go through on MFP-enabled networks as the key for it is
marked tainted before the frame is transmitted.
Allow a tainted key to be used for deauth frames. Worst
case, we'll use a wrong key because the PTK was rekeyed
while suspended, but more likely the PTK is still fine
and the taint flag really only applies to the GTK(s).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment about allocating the IEs together with
the BSS struct is no longer true, remove it. Also
fix a typo in the same area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ssid/ssid_len fields in the private BSS
struct are unused, contrary to the comment
we do look up the SSID in the few cases we
need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As Thomas pointed out, cfg80211_get_mesh() is
unused and can be removed.
Cc: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of first checking if a BSS is an MBSS
and then doing the comparisons, inline it all
into the BSS comparison function. This avoids
doing the IE searches twice and is also a lot
less code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to find a hidden SSID, the lookup function
is done wrong; the code is trying to combine the two
lookups into one, and as a consequence doesn't always
find the entry at all. To understand this, consider a
case where multiple BSS entries with the same channel
and BSSID exist but have different SSID length. Then
comparing against the probe response SSID length is
bound to cause problems since the hidden one might be
either zeroed out or zero-length.
To fix this we need to do two lookups for the two ways
to hide SSIDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of duplicating the rbtree functions, pass
an argument to the compare function. This removes
the code duplication for the two searches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In per-station statistics, present 32bit counters are too small
for practical purposes - with gigabit speeds, it get overlapped
every few seconds.
Expand counters in the struct station_info to be 64-bit.
Driver can still fill only 32-bit and indicate in @filled
only bits like STATION_INFO_[TR]X_BYTES; in case driver provides
full 64-bit counter, it should also set in @filled
bit STATION_INFO_[TR]RX_BYTES64
Netlink sends both 32-bit and 64-bit counters, if present, to not
break userspace.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[change to also have 32-bit counters if driver advertises 64-bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IRQ_PER_CPU Kconfig symbol was removed in the following commit:
Commit 6a58fb3bad ("genirq: Remove
CONFIG_IRQ_PER_CPU") merged in v2.6.39-rc1.
But IRQ_PER_CPU wasn't removed from any of the architecture Kconfig
files where it was defined or selected. It's completely unused so remove
the remaining references.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <uclinux-dist-devel@blackfin.uclinux.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linuxppc-dev@lists.ozlabs.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Link: http://lkml.kernel.org/r/1359972583-17134-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On tile architecture (with "make allyesconfig") including
<linux/swiotlb.h> is required to call swiotlb_nr_tbl().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
