Enable 83xx virtual NIC mode
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flash template provides instructions to stop, restart and initalize the
firmware. These instructions are abstracted as a series of read, write and
poll operations on hardware registers. Register information and operation
specifics are not exposed to the driver. Driver reads the template from
flash and executes the instructions located at pre-defined offsets.
Template based firmware reset recovery and initialization mechanism minimize
driver changes as firmware evolves.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inter Driver Communication (IDC) module.
CNA function drivers(ISCSI, FCOE and NIC) which shares the adapter
relies on IDC mechanism for gracefull shut down, restart and
firmware error recovery.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx adapter flash memory map, data structures and interface routines
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable base 83xx adapter driver.
Common driver interface routines like probe,
interface up/down routines, irq and resource
allocation routines are modified to add support for 83xx
adapter.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter - Qlogic 83XX CNA
Use QLC_SHARED_REG_RD32 and QLC__SHARED_REG_WR32 macros
for 82xx and 83xx common register access.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter - Qlogic 83XX CNA
Create adapter abstraction layer and seperate 82xx hardware access routines.
Create mailbox based HW interface mechanism
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIC irqdomain code added in commit
07c9249f1f
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Versatile starts to register Linux IRQ numbers from offset 0
which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs
by 32 to get rid of the problem.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to support secure and non-secure platforms in multi-platform
kernels, errata work-arounds that access secure only registers need to
be disabled. Make all the errata options that fit in this category
depend on !CONFIG_ARCH_MULTIPLATFORM.
This will effectively remove the errata options as platforms are
converted over to multi-platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 errata work-arounds using .set_debug function are only needed on
r3p0 and earlier, so check the rev and only set .set_debug on older revs.
Avoiding debug register accesses fixes aborts on non-secure platforms
like highbank. It is assumed that non-secure platforms needing these
work-arounds have already implemented .set_debug with secure monitor
calls.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In function rg_mblk_search, it's searching for multiple blocks in
a given state (e.g. "free"). If there's an active block reservation
its goal is the next free block of that. If the resource group
contains the dinode's goal block, that's used for the search. But
if neither is the case, it uses the rgrp's last allocated block.
That way, consecutive allocations appear after one another on media.
The problem comes in when you hit the end of the rgrp; it would never
start over and search from the beginning. This became a problem,
since if you deleted all the files and data from the rgrp, it would
never start over and find free blocks. So it had to keep searching
further out on the media to allocate blocks. This patch resets the
rd_last_alloc after it does an unsuccessful search at the end of
the rgrp.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch adds a return code check after calling function
gfs2_rbm_from_block while determining the free extent size.
That way, when the end of an rgrp is reached, it won't try
to process unaligned blocks after the end.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
QE aio tests uncovered a race condition in gfs2_rs_alloc where it's possible
to come out of the function with a valid ip->i_res allocation but it gets
freed before use resulting in a NULL ptr dereference.
This patch envelopes the initial short-circuit check for non-NULL ip->i_res
into the mutex lock. With this patch, I was able to successfully run the
reproducer test multiple times.
Resolves: rhbz#878476
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
When generating the DLM lock name, a value of 0 would skip
the loop and leave the string unchanged. This left locks with
a value of 0 unlabeled. Initializing the string to '0' fixes this.
Signed-off-by: Nathan Straz <nstraz@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Add the various VF device ids (of all supported hardware)
Add the calls to enable_sriov and disable_sriov to enable the
SR-IOV feature. This patch also advances the version and release
date of the bnx2x module.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF <-> VF Bulletin Board is a simple interface between the
PF and the VF. The main reason for the Bulletin Board is to allow
the PF to be the initiator. The VF publishes at 'acquire' stage
the GPA of a Bulletin Board structure it has allocated. The PF notes
this GPA in the VF database. The VF samples the Bulletin Board
periodically for new messages. The latest version of the BB is always
used.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLR indication arrives as an attention from the management processor.
Upon VF flr all FLRed function in the indication have already been
released by Firmware and now we basically need to free the resources
allocated to those VFs, and clean any remainders from the device
(FLR final cleanup).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'release' request is the opposite of the 'acquire' request.
At release, all the resources allocated to the VF are reclaimed.
The release flow applies the close flow if applicable.
Note that there are actually two types of release:
1. The VF has been removed, and so issued a 'release' request
over the VF <-> PF Channel.
2. The PF is going down and so has to release all of it's VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'close' command is the opposite of an init request. Here the
queues of the VF are closed (if any are opened) and released.
This flow applies the 'q_teardown' flow on all the queues.
The VF state is changed by this request.
Interrupts are disabled for the VF when closed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'q_teardown' request is basically the opposite of the 'q_setup'.
Here the PF driver removes from the device the queue it opened against
the VF fastpath ring at 'setup_q' stage, along with all related
rx_mode info.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF driver uses the 'q_filters' message on the VF <-> PF channel
for configuring an open queue, for example when the rxmode changes.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving a 'setup_q' request from the VF over the VF <-> PF
channel the PF driver will open a corresponding queue in the
device. The PF driver configures the queue with appropriate mac
address, vlan configuration, etc from the VF.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics are collected by the PF driver. The collection is
performed via a query sent to the device which is basically an array
of 3-tuples of the form (statistics client, function, DMAE address).
In this patch the PF driver adds to the query, on top of the
statistics clients it is maintaining for itself (rss queues, storage,
etc), the 3-tuples for the VFs it is maintaining. The addresses used
are the GPAs of the statistics buffers supplied by the VF in the
init message on the VF <-> PF channel. The function parameter
ensures that the iommu will translate the GPA to the correct physical
address.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF driver will send an 'init' request as part of its nic load
flow. This message is used by the VF to publish the GPA's of its
status blocks, slow path ring and statistics buffer.
The PF driver notes all this down in the VF database, and also uses
this message to transfer the VF to VF_INIT state internally.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is probed by the VF driver, the VF driver sends an
'acquire' request over the VF <-> PF channel for the resources
it needs to operate (interrupts, queues, etc).
The PF driver either ratifies the request and allocates the resources,
responds with the maximum values it will allow the VF to acquire,
or fails the request entirely if there is a problem.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support interrupt from device which indicates VF has placed
A request on the VF <-> PF channel.
The PF driver issues a DMAE to retrieve the request from the VM
memory (the Ghost Physical Address of the request is contained
in the interrupt. The PF driver uses the GPA in the DMAE request,
which is translated by the IOMMU to the correct physical address).
The request which arrives is examined to recognize the sending VF.
The PF driver allocates a workitem to handle the VF Operation (vfop).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At nic load of the PF, if VFs may be present, prepare the device
for the VFs. Initialize the VF database in preparation of VF arrival.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When A PF determines that it may have to manage SRIOV VFs it
allocates a database for this purpose. The database is intended to
keep track of the VF state, the resources allocated for each VF
(queues, interrupt vectors, etc), the state of the VF's queues.
When the VF loads the database is updated accordingly.
When A VF closes the database is consulted to determine which
resources need to be released (close queues against device, reclaim
interrupt vectors, etc).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF driver is transmitting it must supply the correct mac
address in the parsing BD. This is used for firmware validation
and enforcement and also for tx-switching.
Refactor interrupt ack flow to allow for different BAR addresses of
the hardware in the PF BAR vs the VF BAR.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF driver uses the 'q_filter' request in the VF <-> PF channel to
have the PF configure the requested rxmode to device. ndo_set_rxmode
is called under bottom half lock, so sleeping until the response
arrives over the VF <-> PF channel is out of the question. For this reason
the VF driver returns from the ndo after scheduling a work item, which
in turn processes the rx mode request and adds the classification
information through the VF <-> PF channel accordingly.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is being closed its queues are released via
the 'teardown_q' and the VF itself is closed with
'close'. These are essentially the unload counterparts of
'init' and 'setup_q' from the load flow.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'init' - init an acquired VF. Supply allocation GPAs to PF.
'setup_q' - PF to allocate a queue in device on behalf of the VF.
'set_mac' - PF to configure a mac in device on behalf of the VF.
VF driver uses these requests in the VF <-> PF channel in nic_load
flow.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the VF driver cannot access the chip, except by the
narrow window its BAR allows. Care had to be taken so the VF driver
will not reach code which accesses the chip elsewhere.
Refactor the nic_load flow into parts so it would be
easier to separate the VF-only logic from the PF-only logic.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver uses this request when removed. The PF driver
reclaims all resources allocated for that VF at this
time.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the 'acquire' request to VF <-> PF channel and use it at
VF probe. In the acquire request the VF driver lists the resources
it would like to have. In the response the PF either ratifies the
request, or denies it and supplies the maximum values supported.
The VF may then attempt another acquire request.
This patch adds the bnx2x_vfpf.c file which contains the
implementation of the VF to PF hardware channel.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support probing and removing of a bnx2x virtual function
the following were added:
1. add bnx2x_vfpf.h: defines the VF to PF channel
2. add bnx2x_sriov.h: header for bnx2x SR-IOV functionality
3. enumerate VF hw types (identify VFs)
4. if driving a VF, map VF bar
5. if driving a VF, allocate Vf to PF channel
6. refactor interrupt flows to include VF
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a file system is mounted on a virtio-blk disk, we then remove it
and then reattach it, the reattached disk gets the same disk name and
ids as the hot removed one.
This leads to very nasty effects - mostly rendering the newly attached
device completely unusable.
Trying what happens when I do the same thing with a USB device, I saw
that the sd node simply doesn't get free'd when a device gets forcefully
removed.
Imitate the same behavior for vd devices. This way broken vd devices
simply are never free'd and newly attached ones keep working just fine.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
If we have mandatory byte-range locks on a file we can't cache reads
because pagereading may have conflicts with these locks on the server.
That's why we should allow level2 oplocks for files without mandatory
locks only.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
If we have a read oplock and set a read lock in it, we can't write to the
locked area - so, filemap_fdatawrite may fail with a no information for a
userspace application even if we request a write to non-locked area. Fix
this by writing directly to the server and then breaking oplock level from
level2 to None.
Also remove CONFIG_CIFS_SMB2 ifdefs because it's suitable for both CIFS
and SMB2 protocols.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
that solution has data races and can end up two identical writes to the
server: when clientCanCacheAll value can be changed during the execution
of __generic_file_aio_write.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Commit bb77209432 ("ARM: OMAP: Move
omap2+ specific parts of sram.c to mach-omap2") adds some new sparse
warnings:
arch/arm/plat-omap/sram.c:43:6: warning: symbol 'omap_sram_push_address' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:65:6: warning: symbol 'omap_sram_reset' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:73:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
This second version fixes the warnings by including <plat/sram.h>, at
Tony's request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Commit 70384a6af0 ("ARM: OMAP3+:
hwmod: Add AM33XX HWMOD data for davinci_mdio module") adds two
new sparse warnings:
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2518:30: warning: symbol 'am33xx_mdio_addr_space' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2526:26: warning: symbol 'am33xx_cpgmac0__mdio' was not declared. Should it be static?
Fix by marking the two new records as static.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
use iio_triggered_buffer_setup(), iio_triggered_buffer_cleanup()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>