The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ARM IM-PD1 add-on module has a few clock of its own, let's
move also these down to the drivers/clk/versatile driver dir
and get rid of any remaining oldschool Integrator clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It turns out that all platforms using the ICST VCO are really
just touching two registers, and in the same way as well: one
register with the VCO configuration as such, and one lock register
that makes it possible to write to the VCO.
Factor this register read/write into the ICST driver so we can
reuse it in the IM-PD1 driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The GPLv2 headers were missing and the subsystem maintainer likes
them so put them in. I am the copyright holder, so explicitly
licensing these under the GPLv2.
Reported-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
From Maxime Ripard:
Here is a pull request to add the support for Allwinner A10 SoCs.
* sunxi/soc2:
ARM: sunxi: Add sunxi restart function via onchip watchdog
ARM: sunxi: Add sun4i and cubieboard support
ARM: sunxi: Add earlyprintk support for UART0 (sun4i)
ARM: sunxi: Restructure sunxi dts/dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
- The code relies on rc_pci_fixup being called, which only happens
when CONFIG_PCI_QUIRKS is enabled, so add that to Kconfig. Omitting
this causes a booting failure with a non-obvious cause.
- Update rc_pci_fixup to set the class properly, copying the
more modern style from other places
- Correct the rc_pci_fixup comment
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
PMU interrupts start at IRQ_DOVE_PMU_START, not IRQ_DOVE_PMU_START + 1.
Fix the condition. (It may have been less likely to occur had the code
been written "if (irq >= IRQ_DOVE_PMU_START" which imho is the easier
to understand notation, and matches the normal way of thinking about
these things.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Kukjin Kim:
Here is Samsung boards update for v3.8 and most of them are updates
for S3C64XX Cragganmore board.
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Add missing device selects for Cragganmore
ARM: EXYNOS: Add missing USB regulators for origen
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: S3C64XX: Add handset module to probed Glenfarclas modules
ARM: S3C64XX: Add WM2200 module for Cragganmore
ARM: S3C64XX: Add hookup for Deanston module on Cragganmore
ARM: S3C64XX: Handle new Amrut modules on Cragganmore
ARM: S3C64XX: Handle revision-specific differences in Cragganmore modules
ARM: S3C64XX: Provide platform data for Tomatin/Balblair on Cragganmore
ARM: S3C64XX: Update hookup for Arizona class devices
ARM: S3C64XX: Add more Glenfarclas module ID strings
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the acknowledgement of PMU interrupts on Dove: some Dove hardware
has not been sensibly designed so that interrupts can be handled in a
race free manner. The PMU is one such instance.
The pending (aka 'cause') register is a bunch of RW bits, meaning that
these bits can be both cleared and set by software (confirmed on the
Armada-510 on the cubox.)
Hardware sets the appropriate bit when an interrupt is asserted, and
software is required to clear the bits which are to be processed. If
we write ~(1 << bit), then we end up asserting every other interrupt
except the one we're processing. So, we need to do a read-modify-write
cycle to clear the asserted bit.
However, any interrupts which occur in the middle of this cycle will
also be written back as zero, which will also clear the new interrupts.
The upshot of this is: there is _no_ way to safely clear down interrupts
in this register (and other similarly behaving interrupt pending
registers on this device.) The patch below at least stops us creating
new interrupts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Kukjin Kim:
This includes supporting legacy i2c controller and ARM down clock
support for exynos5 and small changes.
[olof: It contains a dependency on samsung/hdmi for HDMI DT bindings, for some reason.]
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Signed-off-by: Olof Johansson <olof@lixom.net>
These buffers are a little interesting in that their
content may have variable endianness, but all but one
element will definitely be big endian.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
cm-t3517 starting from revision 1.2 does not have the 32K oscilator
wired to the AM3517 SoC.
Therefore switch to use the GPTIMER for system clock.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* samsung/pinctrl:
pinctrl: samsung: Update error check for unsigned variables
pinctrl: samsung: Add support for EXYNOS4X12
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
pinctrl: samsung: Use one GPIO chip per pin bank
pinctrl: exynos: Use one IRQ domain per pin bank
pinctrl: samsung: Include bank-specific eint offset in bank struct
pinctrl: samsung: Hold pointer to driver data in bank struct
pinctrl: samsung: Match pin banks with their device nodes
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
pinctrl: samsung: Distinguish between pin group and bank nodes
pinctrl: samsung: Remove static pin enumerations
pinctrl: samsung: Assing pin numbers dynamically
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
pinctrl: samsung: Detect and handle unsupported configuration types
CONFIG_OMAP_32K_TIMER is kind of standing on the single zImage way.
Make OMAP2+ timer code independant from the CONFIG_OMAP_32K_TIMER
setting.
To remove the dependancy, several conversions/additions had to be done:
1) Timer initialization functions are named by the platform
name and the clock source in use.
This also makes it possible to define and use the GPTIMER as the
clock source instead of the 32K timer on platforms that do not have
the 32K timer ip block or the 32K timer is not wired on the board.
Currently, the the timer is chosen in the machine_desc structure on
per board basis. Later, DT should be used to choose the timer.
2) Settings under the CONFIG_OMAP_32K_TIMER option are used as defaults
and those under !CONFIG_OMAP_32K_TIMER are removed.
This removes the CONFIG_OMAP_32K_TIMER on OMAP2+ timer code.
3) Since we have all the timers defined inside machine_desc structure
and we no longer need the fallback to gp_timer clock source in case
32k_timer clock source is unavailable (namely on AM33xx), we no
longer need the #ifdef around omap2_sync32k_clocksource_init()
function. Remove the #ifdef CONFIG_OMAP_32K_TIMER around the
omap2_sync32k_clocksource_init() function.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
From Kukjin Kim:
This is for Samsung gpio stuff and got the ack from Linus Walleij.
* 'next/gpio-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
gpio: samsung: use pr_* instead of printk
gpio: samsung: Fix input mode setting function for GPIO int
ARM: SAMSUNG: Insert bitmap_gpio_int member in samsung_gpio_chip
From Kukjin Kim:
This is for adding support for DT based exynos5250 hdmi and it adds
device node for hdmi, mixer, hdmiphy and hdmiddc.
* 'next/hdmi-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
From Kukjin Kim:
* 'next/cleanup-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: S3C64XX: Statically define parent clock of "camera" clock
ARM: S3C64XX: Remove duplicated camera clock
ARM: EXYNOS: Add missing static storage class specifiers in clock-exynos5.c
ARM: EXYNOS: Make combiner_of_init function static
ARM: EXYNOS: Make s3c_device_i2c0 always use id 0
ARM: EXYNOS: Remove wrongly placed usb2.0 PHY_CFG definition from PMU_REG
ARM: EXYNOS: reorder inclusions of <linux/platform_data/xxx.h>
ARM: EXYNOS: Remove unused static uart resource information
ARM: EXYNOS: Remove static io-remapping for gic and combiner
ARM: EXYNOS: Remove wrong I2S0 clock from peril clock
ARM: EXYNOS: remove the MMC_CAP2_BROKEN_VOLTAGE
From Alexander Shiyan:
The main direction of this patchset - approaching the platform to the
possibility of using configurations with multiple platforms in a single
kernel. Added support of the majority of the necessary kernel symbol.
Also part of the driver code used only for the platform was moved to the
board code and converted to the use of standard drivers.
* clps711x/soc2:
MAINTAINERS: Add ARM CLPS711X entry
ARM: clps711x: Update defconfig due latest changes and new kernel symbols
ARM: clps711x: Rename board files to match functionality
ARM: clps711x: edb7211: Add support for NOR-Flash
ARM: clps711x: Moving backlight controls of framebuffer driver to the board
ARM: clps711x: p720t: Special driver for handling NAND memory is removed
ARM: clps711x: Moving power management of framebuffer driver to the board
ARM: clps711x: autcpu12: Special driver for handling NAND memory is removed
ARM: clps711x: Unused empty "ACK" calls for IRQ-chips removed
ARM: clps711x: Add FIQ interrupt handling
ARM: clps711x: Implement usage "MULTI_IRQ_HANDLER" kernel option for a platform
ARM: clps711x: Implement usage "SPARSE_IRQ" kernel option for a platform
ARM: clps711x: cdb89712: Special driver for handling memory is removed
ARM: clps711x: Always select AUTO_ZRELADDR for a platform
ARM: clps711x: p720t: Unneeded inclusion of head-sa1100.S removed
ARM: clps711x: Transform clps711x-framebuffer to platform driver and use it
ARM: clps711x: p720t: Using "leds-gpio" driver for LED control
ARM: clps711x: Using platform_driver for ethernet device
This patch moves the backlight controls for clps711x-framebuffer driver
to the board code. To control we use "generic-bl" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
[olof: fixed space/tab whitespace in drivers/video/clps711xfb.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch provide migration to using "gpio-nand" driver instead of using
special driver for handling NAND memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the power management for clps711x-framebuffer driver
to the board code. To control we use "platform-lcd" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch provide migration to using "gpio-nand" and "basic-mmio-gpio"
drivers instead of using special driver for handling NAND memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
CLPS711X-target CPU can have a several FIQ interrupts. With this patch
we adds handling for a one which will be used for ALSA PCM later.
Since FIQ have a separate handler we only add "mask" and "unmask" calls
which will used for enable/disable_irq functions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch provide migration to using "physmap-flash" and "mtd-ram"
drivers instead of using special driver for handling memory.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is required for some of the clps711x series, so we're bringing in
the dependency explicitly.
By Linus Walleij (5) and others
via Linus Walleij
* depends/gpio-devel:
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
gpio/em: convert to linear IRQ domain
gpio/mvebu: convert to use irq_domain_add_simple()
gpio/tegra: convert to use linear irqdomain
gpiolib: unlock on error in gpio_export()
gpiolib: add gpio get direction callback support
GPIO: clps711x: Fix direction logic for PORTD
GPIO: clps711x: Fix return value for gpio_clps711x_get
gpiolib: Refactor gpio_export
GPIO: vt8500: Add extended gpio bank for WM8505/WM8650
gpio: clps711x: delete local <mach/gpio.h> header
GPIO: Add support for GPIO on CLPS711X-target platform
DA9055 GPIO driver
gpio/gpio-omap: Use existing pointer to struct device
gpio/gpio-pl061: Covert to use devm_* functions
Signed-off-by: Olof Johansson <olof@lixom.net>
The sparse warning is:
"drivers/media/usb/stkwebcam/stk-webcam.c:59:5:
warning: symbol 'first_init' was not declared. Should it be static?"
Declare variable 'first_init' as static and local to the function.
Found by Hans Verkuil's daily build. Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an entry in MAINTAINERS file for
TI Davinci media drivers.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds MAINTAINERS entry for radio-mr800 usb radio driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And the smiapp-pll which is in a way part of the smiapp driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare().
Also fixes some issues related to clk clean up in the driver
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The thing is that team_dev_queue_xmit() returns NET_XMIT_* or -E*.
bc_trasmit() should return true in case all went well. So use ! to get
correct retval from team_dev_queue_xmit() result.
This bug caused iface statistics to be badly computed.
This bug was introduced by:
team: add broadcast mode (5fc889911a)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have the following warning message when running modules install
for sign ko files:
# make modules_install
...
INSTALL drivers/input/touchscreen/pcap_ts.ko
Found = in conditional, should be == at scripts/sign-file line 164.
Found = in conditional, should be == at scripts/sign-file line 161.
Found = in conditional, should be == at scripts/sign-file line 159.
This patch change replace '=' by '==' in elsif conditions for avoid the
above warning messages.
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>