Commit graph

361,258 commits

Author SHA1 Message Date
Leonard Crestez
fded5fc841 cpufreq: imx6q: Fix imx6sx low frequency support
This patch contains the minimal changes required to support imx6sx OPP
of 198 Mhz. Without this patch cpufreq still reports success but the
frequency is not changed, the "arm" clock will still be at 396000000 in
clk_summary.

In order to do this PLL1 needs to be still kept enabled while changing
the ARM clock. This is a hardware requirement: when ARM_PODF is changed
in CCM we need to check the busy bit of CCM_CDHIPR bit 16 arm_podf_busy,
and this bit is sync with PLL1 clock, so if PLL1 NOT enabled, this
bit will never get clear.

Keep pll1_sys explicitly enabled until after the rate is change to deal
with this. Otherwise from the clk framework perspective pll1_sys is
unused and gets turned off.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-29 00:22:52 +02:00
Colin Ian King
843791bb6c cpufreq: speedstep-lib: make several arrays static, makes code smaller
Don't populate arrays on the stack, instead make them static.
Makes the object code smaller by over 860 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  10716	   5196	      0	  15912	   3e28	drivers/cpufreq/speedstep-lib.o

After:
   text	   data	    bss	    dec	    hex	filename
   9690	   5356	      0	  15046	   3ac6	drivers/cpufreq/speedstep-lib.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-29 00:21:41 +02:00
Christophe Jaillet
9a6e91d08e cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
If 'dev_pm_opp_set_supported_hw()' fails, 'opp_data->opp_node' refcount
will be decremented 2 times.
One, just a few lines above, and another one in the error handling path.

Fix it by simply moving the 'of_node_put' call of the normal path.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-25 01:43:07 +02:00
Viresh Kumar
d79d148b64 cpufreq: dt-platdev: Drop few entries from whitelist
Drop few ARM (32 and 64 bit) platforms from the whitelist which always
use "operating-points-v2" property from their DT. They should continue
to work after this patch.

Tested on Hikey platform (only the "hisilicon,hi6220" entry).

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-25 01:41:03 +02:00
Viresh Kumar
edeec420de cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
The initial idea of creating the cpufreq-dt-platdev.c file was to keep a
list of platforms that use the "operating-points" (V1) bindings and
create cpufreq device for them only, as we weren't sure which platforms
would want the device to get created automatically as some had their own
cpufreq drivers as well, or wanted to initialize cpufreq after doing
some stuff from platform code.

But that wasn't the case with platforms using "operating-points-v2"
property. We wanted the device to get created automatically without the
need of adding them to the whitelist. Though, we will still have some
exceptions where we don't want to create the device automatically.

Rename the earlier platform list as *whitelist* and create a new
*blacklist* as well.

The cpufreq-dt device will get created if:
- The platform is there in the whitelist OR
- The platform has "operating-points-v2" property in CPU0's DT node and
  isn't part of the blacklist .

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-25 01:41:03 +02:00
Rob Herring
cc5a7a7494 cpufreq: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-25 01:20:46 +02:00
Viresh Kumar
e948bc8fbe cpufreq: Cap the default transition delay value to 10 ms
If transition_delay_us isn't defined by the cpufreq driver, the default
value of transition delay (time after which the cpufreq governor will
try updating the frequency again) is currently calculated by multiplying
transition_latency (nsec) with LATENCY_MULTIPLIER (1000) and then
converting this time to usec. That gives the exact same value as
transition_latency, just that the time unit is usec instead of nsec.

With acpi-cpufreq for example, transition_latency is set to around 10
usec and we get transition delay as 10 ms. Which seems to be a
reasonable amount of time to reevaluate the frequency again.

But for platforms where frequency switching isn't that fast (like ARM),
the transition_latency varies from 500 usec to 3 ms, and the transition
delay becomes 500 ms to 3 seconds. Of course, that is a pretty bad
default value to start with.

We can try to come across a better formula (instead of multiplying with
LATENCY_MULTIPLIER) to solve this problem, but will that be worth it ?

This patch tries a simple approach and caps the maximum value of default
transition delay to 10 ms. Of course, userspace can still come in and
change this value anytime or individual drivers can rather provide
transition_delay_us instead.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-22 15:50:03 +02:00
Linus Walleij
919096f7f3 cpufreq: dbx500: Delete obsolete driver
We have moved the Ux500 over to use the generic DT based
cpufreq driver, so delete the old custom driver.

At the same time select CPUFREQ_DT from the machine's
Kconfig in order to satisfy the "default ARCH_U8500"
selection on the old driver.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-22 15:50:02 +02:00
Linus Walleij
836a1e25df mfd: db8500-prcmu: Get rid of cpufreq dependency
The ARMSS clock, also known as the operating point of the
CPU, should not cross-depend on cpufreq like this. Move
the code to use just frequencies and remove the false
frequency (1GHz) and put in the actual frequency provided
by the ARMSS clock (998400000 Hz) as part of the process.

After this and the related cpufreq patch, the DB8500 will
simply use the standard DT cpufreq driver to change the
operating points through the common clock framework using
the ARMSS clock.

Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-22 15:49:33 +02:00
Linus Walleij
ff6c349f74 cpufreq: enable the DT cpufreq driver on the Ux500
This enables the generic DT and OPP-based cpufreq driver on the
ST-Ericsson Ux500 series.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-18 01:46:40 +02:00
Arvind Yadav
a804d51004 cpufreq: Loongson2: constify platform_device_id
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-18 01:44:21 +02:00
Khiem Nguyen
bea2ebca6b cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
This patch adds the r8a7796 support the generic cpufreq driver
by adding an appropriate compat string. This is in keeping
with support for other Renesas ARM and arm64 based SoCs.

Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
[simon: new changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-18 01:42:46 +02:00
Sudeep Holla
b20a3f3d8a cpufreq: remove setting of policy->cpu in policy->cpus during init
policy->cpu is copied into policy->cpus in cpufreq_online() before
calling into cpufreq_driver->init(). So there's no need to set the
same in the individual driver init() functions again.

This patch removes the redundant setting of policy->cpu in policy->cpus
in intel_pstate and cppc drivers.

Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-18 01:41:37 +02:00
Sean Wang
ccc03d86e2 cpufreq: mediatek: add support of cpufreq to MT7622 SoC
MT7622 is a 64-bit ARMv8 based dual-core SoC (2 * Cortex-A53) with a
single cluster. The hardware is also compatible with the current driver,
so add MT7622 as one of the compatible string list.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-10 01:29:53 +02:00
Sean Wang
862e0104f4 cpufreq: mediatek: add cleanups with the more generic naming
Since more MediaTek SoCs can be supported with the cpufreq driver and not
limited to MT8173, a couple of cleanups are done here with renaming those
functions and related structures with "mtk" instead of "mt8173".

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-10 01:29:53 +02:00
Khiem Nguyen
034def597b cpufreq: rcar: Add support for R8A7795 SoC
After the commit "a399dc9fc5 cpufreq: shmobile: Use generic platdev
driver", will use cpufreq-dt-platdev driver to enable cpufreq-dt support.
Hence, follow the implementation to support new R8A7795 SoC.

Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-08 17:09:54 +02:00
Finley Xiao
319af40a00 cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
This patch adds the rk3328 compatible string for supporting
the generic cpufreq driver on RK3328.

Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-04 14:22:43 +02:00
Julia Lawall
38c1c6a9f3 cpufreq: s5pv210: add missing of_node_put()
for_each_compatible_node performs an of_node_get on each iteration, so a
return from the loop requires an of_node_put.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
local idexpression n;
expression e,e1,e2;
statement S;
iterator i1;
iterator name for_each_compatible_node;
@@

 for_each_compatible_node(n,e1,e2) {
   ...
(
   of_node_put(n);
|
   e = n
|
   return n;
|
   i1(...,n,...) S
|
+  of_node_put(n);
?  return ...;
)
   ...
 }
// </smpl>

Additionally, call of_node_put on the previous value of np, obtained from
of_find_compatible_node, that is no longer accessible at the point of the
for_each_compatible_node.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 22:54:01 +02:00
Viresh Kumar
fc4c709fc8 cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
With the recent updates, CPUFREQ_ETERNAL is only used by the drivers
which don't know their transition latency but want to use dynamic
switching.

Anyway, the routine cpufreq_policy_transition_delay_us() caps the value
of transition latency to 10 ms now and that can be used safely with such
platforms.

Remove the check from cpufreq_init_governor() and allow dynamic
switching for such configurations as well.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 00:15:47 +02:00
Viresh Kumar
fe829ed8ef cpufreq: Add CPUFREQ_NO_AUTO_DYNAMIC_SWITCHING cpufreq driver flag
The policy->transition_latency field is used for multiple purposes
today and its not straight forward at all. This is how it is used:

A. Set the correct transition_latency value.

B. Set it to CPUFREQ_ETERNAL because:
   1. We don't want automatic dynamic switching (with
      ondemand/conservative) to happen at all.
   2. We don't know the transition latency.

This patch handles the B.1. case in a more readable way. A new flag for
the cpufreq drivers is added to disallow use of cpufreq governors which
have dynamic_switching flag set.

All the current cpufreq drivers which are setting transition_latency
unconditionally to CPUFREQ_ETERNAL are updated to use it. They don't
need to set transition_latency anymore.

There shouldn't be any functional change after this patch.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 00:15:46 +02:00
Viresh Kumar
ed4676e254 cpufreq: Replace "max_transition_latency" with "dynamic_switching"
There is no limitation in the ondemand or conservative governors which
disallow the transition_latency to be greater than 10 ms.

The max_transition_latency field is rather used to disallow automatic
dynamic frequency switching for platforms which didn't wanted these
governors to run.

Replace max_transition_latency with a boolean (dynamic_switching) and
check for transition_latency == CPUFREQ_ETERNAL along with that. This
makes it pretty straight forward to read/understand now.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 00:15:45 +02:00
Viresh Kumar
768608a578 cpufreq: arm_big_little: Make ->get_transition_latency() mandatory
All users of arm_big_little driver are defining it and there is no need
to keep it optional.

Make it mandatory to remove the always true conditional statement.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 00:15:44 +02:00
Viresh Kumar
b8b78825a2 cpufreq: Don't set transition_latency for setpolicy drivers
The transition_latency field isn't used for drivers with ->setpolicy()
callback present and there is no point setting it from the drivers.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-26 00:15:43 +02:00
Viresh Kumar
aa7519af45 cpufreq: Use transition_delay_us for legacy governors as well
The policy->transition_delay_us field is used only by the schedutil
governor currently, and this field describes how fast the driver wants
the cpufreq governor to change CPUs frequency. It should rather be a
common thing across all governors, as it doesn't have any schedutil
dependency here.

Create a new helper cpufreq_policy_transition_delay_us() to get the
transition delay across all governors.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:25:20 +02:00
Viresh Kumar
2d04503632 cpufreq: governor: Drop min_sampling_rate
The cpufreq core and governors aren't supposed to set a limit on how
fast we want to try changing the frequency. This is currently done for
the legacy governors with help of min_sampling_rate.

At worst, we may end up setting the sampling rate to a value lower than
the rate at which frequency can be changed and then one of the CPUs in
the policy will be only changing frequency for ever.

But that is something for the user to decide and there is no need to
have special handling for such cases in the core. Leave it for the user
to figure out.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:25:20 +02:00
Marc Gonzalez
9dbd224f9e cpufreq: dt: Don't use generic platdev driver for tango
On tango platforms, firmware configures the CPU clock, and Linux is
then only allowed to use the cpu_clk_divider to change the frequency.
Build the OPP table dynamically at init, in order to support whatever
firmware throws at us.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:20:59 +02:00
Sean Wang
501c574f4e cpufreq: mediatek: Add support of cpufreq to MT2701/MT7623 SoC
MT2701/MT7623 is a 32-bit ARMv7 based quad-core (4 * Cortex-A7) with
single cluster and this hardware is also compatible with the existing
driver through enabling CPU frequency feature with operating-points-v2
bindings. Also, this driver actually supports all MediaTek SoCs, the
Kconfig menu entry and file name itself should be updated with more
generic name to drop "MT8173"

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-22 02:19:37 +02:00
Shubhrajyoti Datta
a5685781df cpufreq: dt: Add zynqmp to the cpufreq dt platdev
Add zynqmp to the cpufreq dt platform device.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-16 02:12:35 +02:00
Gustavo A. R. Silva
c95a05f9f3 cpufreq: speedstep: remove unnecessary static in speedstep_detect_chipset()
Remove unnecessary static on local variable hostbridge.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.

This issue was detected using Coccinelle and the following semantic patch:

@bad exists@
position p;
identifier x;
type T;
@@

static T x@p;
...
x = <+...x...+>

@@
identifier x;
expression e;
type T;
position p != bad.p;
@@

-static
 T x@p;
 ... when != x
     when strict
?x = e;

In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:

before:
   text    data     bss     dec     hex filename
   5084    3392     256    8732    221c drivers/cpufreq/speedstep-ich.o

after:
   text    data     bss     dec     hex filename
   5062    3304     192    8558    216e drivers/cpufreq/speedstep-ich.o

Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-07-16 02:12:35 +02:00
Linus Torvalds
52f6c588c7 Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
 CRNG is initialized.
 
 Also print a warning if get_random_*() is called before the CRNG is
 initialized.  By default, only one single-line warning will be printed
 per boot.  If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
 warning will be printed for each function which tries to get random
 bytes before the CRNG is initialized.  This can get spammy for certain
 architecture types, so it is not enabled by default.
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAllqXNUACgkQ8vlZVpUN
 gaPtAgf/aUbXZuWYsDQzslHsbzEWi+qz4QgL885/w4L00pEImTTp91Q06SDxWhtB
 KPvGnZHS3IofxBh2DC+6AwN6dPMoWDCfYhhO6po3FSz0DiPRIQCTuvOb8fhKY1X7
 rTdDq2xtDxPGxJ25bMJtlrgzH2XlXPpVyPUeoc9uh87zUK5aesXpUn9kBniRexoz
 ume+M/cDzPKkwNQpbLq8vzhNjoWMVv0FeW2akVvrjkkWko8nZLZ0R/kIyKQlRPdG
 LZDXcz0oTHpDS6+ufEo292ZuWm2IGer2YtwHsKyCAsyEWsUqBz2yurtkSj3mAVyC
 hHafyS+5WNaGdgBmg0zJxxwn5qxxLg==
 =ua7p
 -----END PGP SIGNATURE-----

Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random

Pull random updates from Ted Ts'o:
 "Add wait_for_random_bytes() and get_random_*_wait() functions so that
  callers can more safely get random bytes if they can block until the
  CRNG is initialized.

  Also print a warning if get_random_*() is called before the CRNG is
  initialized. By default, only one single-line warning will be printed
  per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
  warning will be printed for each function which tries to get random
  bytes before the CRNG is initialized. This can get spammy for certain
  architecture types, so it is not enabled by default"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: reorder READ_ONCE() in get_random_uXX
  random: suppress spammy warnings about unseeded randomness
  random: warn when kernel uses unseeded randomness
  net/route: use get_random_int for random counter
  net/neighbor: use get_random_u32 for 32-bit hash random
  rhashtable: use get_random_u32 for hash_rnd
  ceph: ensure RNG is seeded before using
  iscsi: ensure RNG is seeded before use
  cifs: use get_random_u32 for 32-bit lock random
  random: add get_random_{bytes,u32,u64,int,long,once}_wait family
  random: add wait_for_random_bytes() API
2017-07-15 12:44:02 -07:00
Linus Torvalds
93ff818597 Merge branch 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more __copy_.._user elimination from Al Viro.

* 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  drm_dp_aux_dev: switch to read_iter/write_iter
2017-07-15 11:47:27 -07:00
Linus Torvalds
568d135d33 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "Boston platform support:
   - Document DT bindings
   - Add CLK driver for board clocks

  CM:
   - Avoid per-core locking with CM3 & higher
   - WARN on attempt to lock invalid VP, not BUG

  CPS:
   - Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
   - Prevent multi-core with dcache aliasing
   - Handle cores not powering down more gracefully
   - Handle spurious VP starts more gracefully

  DSP:
   - Add lwx & lhx missaligned access support

  eBPF:
   - Add MIPS support along with many supporting change to add the
     required infrastructure

  Generic arch code:
   - Misc sysmips MIPS_ATOMIC_SET fixes
   - Drop duplicate HAVE_SYSCALL_TRACEPOINTS
   - Negate error syscall return in trace
   - Correct forced syscall errors
   - Traced negative syscalls should return -ENOSYS
   - Allow samples/bpf/tracex5 to access syscall arguments for sane
     traces
   - Cleanup from old Kconfig options in defconfigs
   - Fix PREF instruction usage by memcpy for MIPS R6
   - Fix various special cases in the FPU eulation
   - Fix some special cases in MIPS16e2 support
   - Fix MIPS I ISA /proc/cpuinfo reporting
   - Sort MIPS Kconfig alphabetically
   - Fix minimum alignment requirement of IRQ stack as required by
     ABI / GCC
   - Fix special cases in the module loader
   - Perform post-DMA cache flushes on systems with MAARs
   - Probe the I6500 CPU
   - Cleanup cmpxchg and add support for 1 and 2 byte operations
   - Use queued read/write locks (qrwlock)
   - Use queued spinlocks (qspinlock)
   - Add CPU shared FTLB feature detection
   - Handle tlbex-tlbp race condition
   - Allow storing pgd in C0_CONTEXT for MIPSr6
   - Use current_cpu_type() in m4kc_tlbp_war()
   - Support Boston in the generic kernel

  Generic platform:
   - yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
   - yamon-dt: Support > 256MB of RAM
   - yamon-dt: Use serial* rather than uart* aliases
   - Abstract FDT fixup application
   - Set RTC_ALWAYS_BCD to 0
   - Add a MAINTAINERS entry

  core kernel:
   - qspinlock.c: include linux/prefetch.h

  Loongson 3:
   - Add support

  Perf:
   - Add I6500 support

  SEAD-3:
   - Remove GIC timer from DT
   - Set interrupt-parent per-device, not at root node
   - Fix GIC interrupt specifiers

  SMP:
   - Skip IPI setup if we only have a single CPU

  VDSO:
   - Make comment match reality
   - Improvements to time code in VDSO"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
  locking/qspinlock: Include linux/prefetch.h
  MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
  MIPS: Fix minimum alignment requirement of IRQ stack
  MIPS: generic: Support MIPS Boston development boards
  MIPS: DTS: img: Don't attempt to build-in all .dtb files
  clk: boston: Add a driver for MIPS Boston board clocks
  dt-bindings: Document img,boston-clock binding
  MIPS: Traced negative syscalls should return -ENOSYS
  MIPS: Correct forced syscall errors
  MIPS: Negate error syscall return in trace
  MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
  MIPS16e2: Provide feature overrides for non-MIPS16 systems
  MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
  MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
  MIPS: MIPS16e2: Identify ASE presence
  MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
  MIPS: VDSO: Add implementation of gettimeofday() fallback
  MIPS: VDSO: Add implementation of clock_gettime() fallback
  MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
  MIPS: Use current_cpu_type() in m4kc_tlbp_war()
  ...
2017-07-15 10:59:54 -07:00
Sebastian Andrzej Siewior
72e5c740f6 random: reorder READ_ONCE() in get_random_uXX
Avoid the READ_ONCE in commit 4a072c71f4 ("random: silence compiler
warnings and fix race") if we can leave the function after
arch_get_random_XXX().

Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
2017-07-15 12:33:22 -04:00
Theodore Ts'o
eecabf5674 random: suppress spammy warnings about unseeded randomness
Unfortunately, on some models of some architectures getting a fully
seeded CRNG is extremely difficult, and so this can result in dmesg
getting spammed for a surprisingly long time.  This is really bad from
a security perspective, and so architecture maintainers really need to
do what they can to get the CRNG seeded sooner after the system is
booted.  However, users can't do anything actionble to address this,
and spamming the kernel messages log will only just annoy people.

For developers who want to work on improving this situation,
CONFIG_WARN_UNSEEDED_RANDOM has been renamed to
CONFIG_WARN_ALL_UNSEEDED_RANDOM.  By default the kernel will always
print the first use of unseeded randomness.  This way, hopefully the
security obsessed will be happy that there is _some_ indication when
the kernel boots there may be a potential issue with that architecture
or subarchitecture.  To see all uses of unseeded randomness,
developers can enable CONFIG_WARN_ALL_UNSEEDED_RANDOM.

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
2017-07-15 12:19:28 -04:00
Linus Torvalds
0ffff118b1 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull a few more input updates from Dmitry Torokhov:

 - multi-touch handling for Xen

 - fix for long-standing bug causing crashes in i8042 on boot

 - change to gpio_keys to better handle key presses during system state
   transition

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - fix crash at boot time
  Input: gpio_keys - handle the missing key press event in resume phase
  Input: xen-kbdfront - add multi-touch support
2017-07-14 22:53:37 -07:00
Linus Torvalds
dcf903d0c9 Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:

 - fix new compiler warnings in cavium

 - set post-op IV properly in caam (this fixes chaining)

 - fix potential use-after-free in atmel in case of EBUSY

 - fix sleeping in softirq path in chcr

 - disable buggy sha1-avx2 driver (may overread and page fault)

 - fix use-after-free on signals in caam

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: cavium - make several functions static
  crypto: chcr - Avoid algo allocation in softirq.
  crypto: caam - properly set IV after {en,de}crypt
  crypto: atmel - only treat EBUSY as transient if backlog
  crypto: af_alg - Avoid sock_graft call warning
  crypto: caam - fix signals handling
  crypto: sha1-ssse3 - Disable avx2
2017-07-14 22:49:50 -07:00
Linus Torvalds
96d0d831a5 Device properties framework fix for v4.13-rc1
This fixes a problem with bool properties that could be seen as
 "true" when the property was not present at all by adding a special
 helper for bool properties with checks for all of the requisute
 conditions (Sakari Ailus).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZaLjVAAoJEILEb/54YlRxh/oP/j0LBZ1+vVMp6onKcQZfHkEi
 xA3QyRBz+G48u9dmPmKzpMcXzXmelwuw/6bJix098xFkADVlI2qQkmUYCb5sb06t
 blogDZ3wQokZrVIkFT+kFFUQxcfvX4FgMv6yTerQt+k0xbLXWGighS+46wWvTuPd
 hD3+M+tBw85NMI4pU4rwWIK8UUDjry5lFYsn96cqTe5VC+wUAEy33aFCY8mw55J8
 FGN6DyOmlHbzCdytzi3o4ejfXQkAwjUVAbH/JHVWfEDyxhebo/N6AVAwajtgN8bU
 yHY6nHMz8xL1XtNvc7q6M0i9UySZdk2YrbLh5JtRvUrUWw5OBpE/A1iaUgaGVclC
 5bmeWZww1jejHLnK4U7xUWA2SuQtPE3Kz/rUt3uroJzaCfYuTAxl+7IYftadRW9y
 s+j3mjO3IKjLmCmPQwgPpMmNIore14bFKMnIfStSqyIxtbw59Gt3CnEYpd11UxIh
 noCnnacTGHqSyHQSelf2gdYcWiJo+IUvgFAB4ze33yRPtcfkky4med3MG4I7yXP2
 Tzi+xVGnAmgb9betNINH6sPUw9JImgY19hrQhVyxs8I8sYXV18Wdrkc6JOAZ9bna
 REUXseHkF3ofy7iP1L/yrjOQ31kKwYxJ5kEasg/gwkRV6kzWNJ0CLK/qD7Xp0A3O
 sPm7B8FVfM4xoPOaMngw
 =KEbK
 -----END PGP SIGNATURE-----

Merge tag 'devprop-fix-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull device properties framework fix from Rafael Wysocki:
 "This fixes a problem with bool properties that could be seen as "true"
  when the property was not present at all by adding a special helper
  for bool properties with checks for all of the requisute conditions
  (Sakari Ailus)"

* tag 'devprop-fix-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  device property: Introduce fwnode_call_bool_op() for ops that return bool
2017-07-14 22:39:35 -07:00
Linus Torvalds
1ef27400c5 ACPI fixes for v4.13-rc1
- Fix the return value of acpi_gsi_to_irq() to make the GSI to
    IRQ mapping work on the Mustang (ARM64) platform (Mark Salter).
 
  - Fix an EC driver issue that causes fans to behave abnormally
    after system resume on some systems which turns out to be
    related to switching over the EC into the polling mode during
    the noirq stages of system suspend and resume (Lv Zheng).
 
  - Add quirks for ACPI device objects that need to be treated as
    "always present", because their _STA methods are designed to
    work around Windows driver bugs and return garbage from our
    perspective (Hans de Goede).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZaLggAAoJEILEb/54YlRxmqkP/Rrs7X18JMykuZAOznWYnL6R
 3pIoeFNP0EPoaHEV24okmX/hjwSads+jD5cBCWv1c9R6m//1O7ZDhzE2/JGAYH6R
 bp0D2823hq1oX8/ULxRIZqUlJljOKElqqLb+ZxJ+SYvYEPavwwQqpHrMI1IZMKzP
 S0IWEumiz1fO0yZE2E6XJZvKMX+/RGgck6TllVGwJuFCI/Ol/clUO1recjZlRlGP
 ciYkokMYIhpjFiaIY+uzwzrT2SVKUZ+vQm9pegRqh42o2g1cDmJcYzL9qJRWrc3W
 hIj8rxy5xNsGhny0akxZuh1Yhutk/3oivV1ukoB7ElgtOk6QLI6e3lHeAGgJcX/l
 m8bjX4gj8yjkkkG3K+yPqCKx38xfvcQMazYzf3irU+37wUgJadtaxlVdUoFYgobt
 rYMtfFdjp8WQiQUrparSfOntkDc9z6myBOX0g+g1F6nxvi+rO7cBreW/Pal0dwY3
 ntLhgOxKUGjQYICTK7s4eUPBL4wX9HdX5F/7cI/dP4iYGtfu7Hz5BghRvVNEv2QK
 lsBpwP52mhL8NyqVF7XGrIACHaq/fium0QIiWAM3OdqGUsb1mGwL5JJVrDuqKntX
 W4jj4fronkBpS1ospfUqp49ImGu6ycqslWkrwuQ+Vyt2XDk+MyRvXjcchEmu0PCp
 GKlhazla5NDaWuuAVPJc
 =6Zb+
 -----END PGP SIGNATURE-----

Merge tag 'acpi-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI fixes from Rafael Wysocki:
 "These fix the return value of an IRQ mapping routine in the ACPI core,
  fix an EC driver issue causing abnormal fan behavior after system
  resume on some systems and add quirks for ACPI device objects that
  need to be treated as "always present" to work around bogus
  implementations of the _STA control method.

  Specifics:

   - Fix the return value of acpi_gsi_to_irq() to make the GSI to IRQ
     mapping work on the Mustang (ARM64) platform (Mark Salter).

   - Fix an EC driver issue that causes fans to behave abnormally after
     system resume on some systems which turns out to be related to
     switching over the EC into the polling mode during the noirq stages
     of system suspend and resume (Lv Zheng).

   - Add quirks for ACPI device objects that need to be treated as
     "always present", because their _STA methods are designed to work
     around Windows driver bugs and return garbage from our perspective
     (Hans de Goede)"

* tag 'acpi-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / x86: Add KIOX000A accelerometer on GPD win to always_present_ids array
  ACPI / x86: Add Dell Venue 11 Pro 7130 touchscreen to always_present_ids
  ACPI / x86: Allow matching always_present_id array entries by DMI
  Revert "ACPI / EC: Enable event freeze mode..." to fix a regression
  ACPI / EC: Drop EC noirq hooks to fix a regression
  ACPI / irq: Fix return code of acpi_gsi_to_irq()
2017-07-14 22:27:13 -07:00
Linus Torvalds
e37720e25d Power management fixes for v4.13-rc1
- Avoid clearing the PCI PME Enable bit for devices as a result of
    config space restoration which confuses AML executed afterward and
    causes wakeup events to be lost on some systems (Rafael Wysocki).
 
  - Fix the native PCIe PME interrupts handling in the cases when the
    PME IRQ is set up as a system wakeup one so that runtime PM remote
    wakeup works as expected after system resume on systems where that
    happens (Rafael Wysocki).
 
  - Fix the device PM QoS sysfs interface to handle invalid user input
    correctly instead of using an unititialized variable value as the
    latency tolerance for the device at hand (Dan Carpenter).
 
  - Get rid of one more rounding error from intel_pstate computations
    (Srinivas Pandruvada).
 
  - Fix the schedutil cpufreq governor to prevent it from possibly
    accessing unititialized data structures from governor callbacks in
    some cases on systems when multiple CPUs share a single cpufreq
    policy object (Vikram Mulukutla).
 
  - Fix the return values of probe routines in two devfreq drivers
    (Gustavo Silva).
 
  - Constify an attribute_group structure in devfreq (Arvind Yadav).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZaLe2AAoJEILEb/54YlRxbi8P/jbQkFdtZinL8eR5DNlUt9jn
 ZzOnPNNJL0xj2dRJ8qpmHYT1PAQQGIhWyiXavbJqLeZeO5f4AFnFa8Uya+oq6UfP
 rv73RIk+qaogUccdqfa7Y3IcBhuER9q2baSIguLEt4w7+szyiWO+XonK640iTRNz
 moUcf2MCA9EacvwlmANQbnimB7mvwz4Tupgn6zK6zh2BJEBYlkWRbqXE1Zm6tJXb
 +jYwKY0W/hsJbLAUfhbz0Iz6FhvE/ix46NTRw33gWyjmmsUSn4KvIF6mq1+RplD9
 6Rvka6pilqSIWoy3Wr4irAQkaOA8WecvwKGtmTh6mkfQC8TyNbQEHwD0EBSsht9n
 G1OHaWLv7m8PKaxmaLMvQEd8gYWmKAF3EZHA6zT2qN+LCPkMKzab/dEhsU/rxuR2
 Nda57D5iNsGIETfVws9FBeYKOw64gb6TOQi8bunLPQbg15n4XWuL5IjtgnPwHFcU
 xkaxE5UbAmSLIDM8drevIQGIgrEsDDCgezvnVBV8vCYwUyBbzuBb+T6jibPMdNDM
 t0DiF8QwQEGJcxYXEd5FpPamS3rmeKxcf234kzf9lHq0Msq6lMFdhihoJvZJ6rw/
 F18ZkAT3ni546CRmknJrUmeg7FjwHsTgJo7K7MArIcHBLhsA59+Bv2Mh+UIH//yT
 57c1OquHgPXx1uTULMC3
 =G9eQ
 -----END PGP SIGNATURE-----

Merge tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
 "These fix a recently exposed issue in the PCI device wakeup code and
  one older problem related to PCI device wakeup that has been reported
  recently, modify one more piece of computations in intel_pstate to get
  rid of a rounding error, fix a possible race in the schedutil cpufreq
  governor, fix the device PM QoS sysfs interface to correctly handle
  invalid user input, fix return values of two probe routines in devfreq
  drivers and constify an attribute_group structure in devfreq.

  Specifics:

   - Avoid clearing the PCI PME Enable bit for devices as a result of
     config space restoration which confuses AML executed afterward and
     causes wakeup events to be lost on some systems (Rafael Wysocki).

   - Fix the native PCIe PME interrupts handling in the cases when the
     PME IRQ is set up as a system wakeup one so that runtime PM remote
     wakeup works as expected after system resume on systems where that
     happens (Rafael Wysocki).

   - Fix the device PM QoS sysfs interface to handle invalid user input
     correctly instead of using an unititialized variable value as the
     latency tolerance for the device at hand (Dan Carpenter).

   - Get rid of one more rounding error from intel_pstate computations
     (Srinivas Pandruvada).

   - Fix the schedutil cpufreq governor to prevent it from possibly
     accessing unititialized data structures from governor callbacks in
     some cases on systems when multiple CPUs share a single cpufreq
     policy object (Vikram Mulukutla).

   - Fix the return values of probe routines in two devfreq drivers
     (Gustavo Silva).

   - Constify an attribute_group structure in devfreq (Arvind Yadav)"

* tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PCI / PM: Fix native PME handling during system suspend/resume
  PCI / PM: Restore PME Enable after config space restoration
  cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race
  PM / QoS: return -EINVAL for bogus strings
  cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
  PM / devfreq: constify attribute_group structures.
  PM / devfreq: tegra: fix error return code in tegra_devfreq_probe()
  PM / devfreq: rk3399_dmc: fix error return code in rk3399_dmcfreq_probe()
2017-07-14 22:24:25 -07:00
Linus Torvalds
ccd5d1b91f New IDT NTB driver and changes to the NTB infrastructure to allow for
this different kind of NTB HW, some style fixes (per Greg KH
 recommendation), and some ntb_test tweaks.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJZZowhAAoJEG5mS6x6i9IjNx8P/0DTYNqBRXg4PSET7+6/Z6yq
 Gz09DRw42dwHXN70ytEwtdRP7jcp3agrvBpRty3EgBygpLlMfOA0iQ6crVdBaza0
 XzRuSl1iEd8oSX3CmJN8dIIWueNiPiqvG6as+j1kjZRZst21oqiMLTO3uO37oBh+
 7/ltCkQtQdco74fiaqnN1iDeKK2lj3qHPJxb2AbeGIxj3lOr6NttPifd0zovimtb
 keBCbaYyQaTxDoNzRwQmZtQNB2bwC/2V1sAM5L1T/xkVIBWXH8AUqJO1iVC4ptjI
 VURvxitDMo28JDc4hgO63AVHsvz8zLbgKsCNK0ia+rtalSLJkDBBN8Qaf7e10hbh
 6YUg2eXzIGusdvFowKnOdXhHYAqrQXMBcWgM2ZVe1YBj8QqZKQ0LL4h9ooVuP9HV
 2hZc3GfMT+iUGmQKdk+rtDVLxYNnsng1NT/5ZxCHBQptrb+/Rqey/wDYdPV2TpnD
 JfRpIFny29NOu74sa4W5GEPWI3AL7WAPAA1WH7RHy5rVDPfX20DcUQdvKvpo25y8
 IdH7caSiBrjpc2GQPvkaziHlLLdZoRNwqJnmHDyUatukdmrElV/oTIRhaYQmLMK0
 /xTFS7YXsmiOGqlfILW9VXdZIlLXSKuNSPX1HUcJ91l2Ik7m0PiK382jKOJVXqcZ
 Frt1CgnCclCDYHBD4yfm
 =SG8F
 -----END PGP SIGNATURE-----

Merge tag 'ntb-4.13' of git://github.com/jonmason/ntb

Pull NTB updates from Jon Mason:
 "The major change in the series is a rework of the NTB infrastructure
  to all for IDT hardware to be supported (and resulting fallout from
  that). There are also a few clean-ups, etc.

  New IDT NTB driver and changes to the NTB infrastructure to allow for
  this different kind of NTB HW, some style fixes (per Greg KH
  recommendation), and some ntb_test tweaks"

* tag 'ntb-4.13' of git://github.com/jonmason/ntb:
  ntb_netdev: set the net_device's parent
  ntb: Add error path/handling to Debug FS entry creation
  ntb: Add more debugfs support for ntb_perf testing options
  ntb: Remove debug-fs variables from the context structure
  ntb: Add a module option to control affinity of DMA channels
  NTB: Add IDT 89HPESxNTx PCIe-switches support
  ntb_hw_intel: Style fixes: open code macros that just obfuscate code
  ntb_hw_amd: Style fixes: open code macros that just obfuscate code
  NTB: Add ntb.h comments
  NTB: Add PCIe Gen4 link speed
  NTB: Add new Memory Windows API documentation
  NTB: Add Messaging NTB API
  NTB: Alter Scratchpads API to support multi-ports devices
  NTB: Alter MW API to support multi-ports devices
  NTB: Alter link-state API to support multi-port devices
  NTB: Add indexed ports NTB API
  NTB: Make link-state API being declared first
  NTB: ntb_test: add parameter for doorbell bitmask
  NTB: ntb_test: modprobe on remote host
2017-07-14 13:31:52 -07:00
Linus Torvalds
4d25ec1966 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:

 - Improve thermal cpu_cooling interaction with cpufreq core.

   The cpu_cooling driver is designed to use CPU frequency scaling to
   avoid high thermal states for a platform. But it wasn't glued really
   well with cpufreq core.

   For example clipped-cpus is copied from the policy structure and its
   much better to use the policy->cpus (or related_cpus) fields directly
   as they may have got updated. Not that things were broken before this
   series, but they can be optimized a bit more.

   This series tries to improve interactions between cpufreq core and
   cpu_cooling driver and does some fixes/cleanups to the cpu_cooling
   driver. (Viresh Kumar)

 - A couple of fixes and cleanups in thermal core and imx, hisilicon,
   bcm_2835, int340x thermal drivers. (Arvind Yadav, Dan Carpenter,
   Sumeet Pawnikar, Srinivas Pandruvada, Willy WOLFF)

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
  thermal: bcm2835: fix an error code in probe()
  thermal: hisilicon: Handle return value of clk_prepare_enable
  thermal: imx: Handle return value of clk_prepare_enable
  thermal: int340x: check for sensor when PTYP is missing
  Thermal/int340x: Fix few typos and kernel-doc style
  thermal: fix source code documentation for parameters
  thermal: cpu_cooling: Replace kmalloc with kmalloc_array
  thermal: cpu_cooling: Rearrange struct cpufreq_cooling_device
  thermal: cpu_cooling: 'freq' can't be zero in cpufreq_state2power()
  thermal: cpu_cooling: don't store cpu_dev in cpufreq_cdev
  thermal: cpu_cooling: get_level() can't fail
  thermal: cpu_cooling: create structure for idle time stats
  thermal: cpu_cooling: merge frequency and power tables
  thermal: cpu_cooling: get rid of 'allowed_cpus'
  thermal: cpu_cooling: OPPs are registered for all CPUs
  thermal: cpu_cooling: store cpufreq policy
  cpufreq: create cpufreq_table_count_valid_entries()
  thermal: cpu_cooling: use cpufreq_policy to register cooling device
  thermal: cpu_cooling: get rid of a variable in cpufreq_set_cur_state()
  thermal: cpu_cooling: remove cpufreq_cooling_get_level()
  ...
2017-07-14 13:12:32 -07:00
Linus Torvalds
907afe5923 MMC core:
- Restore some behaviour of MMC_IOC_MULTI_CMD commands
  - Fix using un-initialized variable in mmc_blk_issue_drv_op()
  - Fix mmc block queue cleanup
 
 MMC host:
  - sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
  - tmio-mmc: Fix bad pointer math
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZaJNDAAoJEP4mhCVzWIwppB4P/26FpKILyBp+HiVBW4FdBHLQ
 VYOdJ/S3jiqWWtDCLj3HUb+I/D1E4C2+mPOdKGx63+igwHu6IO+j9ZprGKRbLtf4
 cB8BmMkHoqww0WzxVkXnrUwdkgMBwpR60UYggM51HPrtwMT9o7juppuG7/RHUPdM
 0p2+eTxTGpVgcKsM+FtISxYzFBC94B4oAAx6hFfWZpHyEdZl+ntRQmveHpA1sCkF
 KvbEPDOaL5UZcXBUKNK9bvyAK3HlwVKq9kF26VSa8sYrd9u/Gt5YmI4fnjzSbjpf
 OjZNMoMxND6daKZiR8obbiAMlKnzMUZyFHyllRG7mMRiWaGOP3/ScHnwbebpVv0O
 Xst9ZjSZir8VLiNCu0M/rxJ2wE3g/QM1J0JngduEoX85NzbIRWTXNNVwPoDk994a
 ex86kqScF4Z9jUH4Iew0RJImlza60RVfLASm7XOBdODyoHwu1zTi2ZAL4a1YKdXx
 ROjOldZDlqn0oNTiv/JGJ4rBfJGPKNQByyvH5QpGmMRM8yYx6X7srdjGYC+vJ6j3
 nPg/k1xYXwxvdZU88Pxvt8uRMSIFEHL6SMdS+KQDPOTRcWgs/yJO3GmrVysUUvup
 MQ+glvkEF22pPGtOU9uNua2jNgD3CxbCDu7Spp/W+Q+DSuJ7jXZHm1vaqtjB79X7
 qfb1kYe1GlxHDROts0s+
 =zgfL
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.13 rc1.

  MMC core:
   - Restore some behaviour of MMC_IOC_MULTI_CMD commands
   - Fix using un-initialized variable in mmc_blk_issue_drv_op()
   - Fix mmc block queue cleanup

  MMC host:
   - sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
   - tmio-mmc: Fix bad pointer math"

* tag 'mmc-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: tmio-mmc: fix bad pointer math
  mmc: block: Prevent new req entering queue after its cleanup
  mmc: block: Let MMC_IOC_MULTI_CMD return zero again for zero entries
  mmc: block: Initialize ret in mmc_blk_issue_drv_op() for MMC_DRV_OP_IOCTL
  mmc: sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
2017-07-14 13:10:06 -07:00
Linus Torvalds
2931dc7d9d pci-v4.13-fixes-1
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZZ+9mAAoJEFmIoMA60/r8q6sP/jyP0rmryX9VJM5Q/LSJffsw
 7J9euvkEZ07pAl6lhO4AAjvAP78XOnXzJCD4XyIQtIVBR6wkcfhJl8NLtfd/Pt3H
 Ri5X8l/ZXthA6U3Ya5Sn/LNwsNghRvvulWLVw1HZjaBvioSwdUty7VXicI6vGe+/
 F+r7ealZPVrglMk74JyHN7GS21OqG7f5GjsF1RlE6kgmKeqqB/0b4jQeK8s6CuVj
 UXu0zJOciKpHlR68M4qSLUFWCBPBXFTHLCAmilqpIzQRZN98sLLk3r9RuB38peMb
 ix7egDn6bi9Hf8lAvpkHwW6GiBKLJIBbfqdFlo8P03MNQHheMOdHzn3RTe8sQ6gh
 mP3MfezwmULd/DleOwKVpUvZDBEETXTb+f6pm8ueyANnNK7/HmtxVswz+qC+trpe
 30Ed4HApVT0xU0sYB5wMUmrpAaLTJuoIk4Zjtc5mFVOM1fGlTyXQzElrvy09oEZz
 PfIKHOY9ky5IPAoB8BMME+f/R8FrssEJ02qEu+0G8k+P9tkFmkT8uZQntl82a5ac
 Lxjfx7eZamWhVRHXMQQBv0tzJYNpbSeoiJBKhtDk5i51NJW9FE+Yi9z/C/0SsxJ7
 ehRRJ8r+DzVWQHaLguraogrWq41T7xRu8OnTiFKdgHCrlvKur+P2GKLzU+VUxoWv
 94XbFFAPfXtJwwwER7AY
 =FGpw
 -----END PGP SIGNATURE-----

Merge tag 'pci-v4.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

 - fix a typo that broke Rockchip enumeration

 - fix a new memory leak in the ARM host bridge failure path

* tag 'pci-v4.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: rockchip: Check for pci_scan_root_bus_bridge() failure correctly
  ARM/PCI: Fix pcibios_init_resource() struct pci_host_bridge leak
2017-07-14 12:36:20 -07:00
Rafael J. Wysocki
9636603da3 Merge branches 'acpi-ec', 'acpi-irq' and 'acpi-quirks'
* acpi-ec:
  Revert "ACPI / EC: Enable event freeze mode..." to fix a regression
  ACPI / EC: Drop EC noirq hooks to fix a regression

* acpi-irq:
  ACPI / irq: Fix return code of acpi_gsi_to_irq()

* acpi-quirks:
  ACPI / x86: Add KIOX000A accelerometer on GPD win to always_present_ids array
  ACPI / x86: Add Dell Venue 11 Pro 7130 touchscreen to always_present_ids
  ACPI / x86: Allow matching always_present_id array entries by DMI
2017-07-14 13:17:53 +02:00
Rafael J. Wysocki
6df609b24b Merge branches 'pm-qos' and 'pm-devfreq'
* pm-qos:
  PM / QoS: return -EINVAL for bogus strings

* pm-devfreq:
  PM / devfreq: constify attribute_group structures.
  PM / devfreq: tegra: fix error return code in tegra_devfreq_probe()
  PM / devfreq: rk3399_dmc: fix error return code in rk3399_dmcfreq_probe()
2017-07-14 13:16:31 +02:00
Rafael J. Wysocki
a252c258dd Merge branches 'pm-cpufreq-sched' and 'intel_pstate'
* pm-cpufreq-sched:
  cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race

* intel_pstate:
  cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
2017-07-14 13:16:16 +02:00
Rafael J. Wysocki
ec4b8ddcd3 Merge branch 'pm-pci'
* pm-pci:
  PCI / PM: Fix native PME handling during system suspend/resume
  PCI / PM: Restore PME Enable after config space restoration
2017-07-14 13:15:49 +02:00
Linus Torvalds
48ea2cedde Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
 "It's been usually busy for summer, with most of the efforts centered
  around TCMU developments and various target-core + fabric driver bug
  fixing activities. Not particularly large in terms of LoC, but lots of
  smaller patches from many different folks.

  The highlights include:

   - ibmvscsis logical partition manager support (Michael Cyr + Bryant
     Ly)

   - Convert target/iblock WRITE_SAME to blkdev_issue_zeroout (hch +
     nab)

   - Add support for TMR percpu LUN reference counting (nab)

   - Fix a potential deadlock between EXTENDED_COPY and iscsi shutdown
     (Bart)

   - Fix COMPARE_AND_WRITE caw_sem leak during se_cmd quiesce (Jiang Yi)

   - Fix TMCU module removal (Xiubo Li)

   - Fix iser-target OOPs during login failure (Andrea Righi + Sagi)

   - Breakup target-core free_device backend driver callback (mnc)

   - Perform TCMU add/delete/reconfig synchronously (mnc)

   - Fix TCMU multiple UIO open/close sequences (mnc)

   - Fix TCMU CHECK_CONDITION sense handling (mnc)

   - Fix target-core SAM_STAT_BUSY + TASK_SET_FULL handling (mnc + nab)

   - Introduce TYPE_ZBC support in PSCSI (Damien Le Moal)

   - Fix possible TCMU memory leak + OOPs when recalculating cmd base
     size (Xiubo Li + Bryant Ly + Damien Le Moal + mnc)

   - Add login_keys_workaround attribute for non RFC initiators (Robert
     LeBlanc + Arun Easi + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (68 commits)
  iscsi-target: Add login_keys_workaround attribute for non RFC initiators
  Revert "qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT"
  tcmu: clean up the code and with one small fix
  tcmu: Fix possbile memory leak / OOPs when recalculating cmd base size
  target: export lio pgr/alua support as device attr
  target: Fix return sense reason in target_scsi3_emulate_pr_out
  target: Fix cmd size for PR-OUT in passthrough_parse_cdb
  tcmu: Fix dev_config_store
  target: pscsi: Introduce TYPE_ZBC support
  target: Use macro for WRITE_VERIFY_32 operation codes
  target: fix SAM_STAT_BUSY/TASK_SET_FULL handling
  target: remove transport_complete
  pscsi: finish cmd processing from pscsi_req_done
  tcmu: fix sense handling during completion
  target: add helper to copy sense to se_cmd buffer
  target: do not require a transport_complete for SCF_TRANSPORT_TASK_SENSE
  target: make device_mutex and device_list static
  tcmu: Fix flushing cmd entry dcache page
  tcmu: fix multiple uio open/close sequences
  tcmu: drop configured check in destroy
  ...
2017-07-13 14:27:32 -07:00
Linus Torvalds
ad51271afc Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton:

- various misc things

- kexec updates

- sysctl core updates

- scripts/gdb udpates

- checkpoint-restart updates

- ipc updates

- kernel/watchdog updates

- Kees's "rough equivalent to the glibc _FORTIFY_SOURCE=1 feature"

- "stackprotector: ascii armor the stack canary"

- more MM bits

- checkpatch updates

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (96 commits)
  writeback: rework wb_[dec|inc]_stat family of functions
  ARM: samsung: usb-ohci: move inline before return type
  video: fbdev: omap: move inline before return type
  video: fbdev: intelfb: move inline before return type
  USB: serial: safe_serial: move __inline__ before return type
  drivers: tty: serial: move inline before return type
  drivers: s390: move static and inline before return type
  x86/efi: move asmlinkage before return type
  sh: move inline before return type
  MIPS: SMP: move asmlinkage before return type
  m68k: coldfire: move inline before return type
  ia64: sn: pci: move inline before type
  ia64: move inline before return type
  FRV: tlbflush: move asmlinkage before return type
  CRIS: gpio: move inline before return type
  ARM: HP Jornada 7XX: move inline before return type
  ARM: KVM: move asmlinkage before type
  checkpatch: improve the STORAGE_CLASS test
  mm, migration: do not trigger OOM killer when migrating memory
  drm/i915: use __GFP_RETRY_MAYFAIL
  ...
2017-07-13 12:38:49 -07:00
Linus Torvalds
6735a1971a platform-drivers-x86 for v4.13-2
Add new platform matches for silead_dmi and ideapad-laptop. Several
 constify patches for attribute_group structures. Fixes for peaq-wmi and
 intel_telemetry*.
 
 *Note: 74a1eb565c platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
        is a duplicate cherry-picked from the 4.12 RC cycle
        (platform-drivers-x86-v4.12-2).
 
 silead_dmi:
  - Add entry for Ployer Momo7w tablet touchscreen
  - Add touchscreen info for I.T.Works TW891 2-in-1
 
 toshiba_acpi:
  - constify attribute_group structures.
 
 asus-wmi:
  - constify attribute_group structures.
 
 panasonic-laptop:
  - constify attribute_group structures.
 
 alienware-wmi:
  - constify attribute_group structures.
 
 samsung-laptop:
  - constify attribute_group structures.
 
 compal-laptop:
  - constify attribute_group structures.
 
 fujitsu-laptop:
  - constify attribute_group structures.
  - add NULL check on devm_kzalloc() return value
 
 peaq-wmi:
  - Fix peaq_ignore_events_counter handling off by 1
 
 ideapad-laptop:
  - Fix indentation in DMI table
  - Add several models to no_hw_rfkill
  - Add IdeaPad V510-15IKB to no_hw_rfkill
 
 intel_telemetry:
  - Add debugfs entry for S0ix residency
 
 intel_telemetry_debugfs:
  - fix some error codes in init
  - fix oops when load/unload module
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJZZ8I5AAoJEKbMaAwKp364YSgH/2snOmcYjFeI7oTHm021peAd
 n23HcTF623dmfQ2LTddPqhtzOAQH9ZZycEd4oW4MASWlntzPZFoxfKiclunvoyKm
 XuycYDOjAl7DnDnoZ8SD7E2QoNAnmmK9riJIudzyHTKCWdxMpWe0mDcR12Rb5uD8
 kOQ+ctI61zWfDWfZj+Fo7HvQ5HsfmLdS4Itjl38H1QyjzIdp0eNA5pZQP0deQ/0w
 vjhmLVT7KEqfRJ09RNIA1eIikyC1uiePUGe13nGEc3P9CpQ/yAVeYvP7za4W7tsF
 jL9s/6uVHnB69WrtWm8Y4l8h4mHymkBV3BxA/fZwaoNTAILH1O5pDHk8T71Po1E=
 =iVsK
 -----END PGP SIGNATURE-----

Merge tag 'platform-drivers-x86-v4.13-2' of git://git.infradead.org/linux-platform-drivers-x86

Pull more x86 platform driver updates from Darren Hart:
 "Add new platform matches for silead_dmi and ideapad-laptop. Several
  constify patches for attribute_group structures. Fixes for peaq-wmi
  and intel_telemetry.

  silead_dmi:
   - Add entry for Ployer Momo7w tablet touchscreen
   - Add touchscreen info for I.T.Works TW891 2-in-1

  toshiba_acpi:
   - constify attribute_group structures.

  asus-wmi:
   - constify attribute_group structures.

  panasonic-laptop:
   - constify attribute_group structures.

  alienware-wmi:
   - constify attribute_group structures.

  samsung-laptop:
   - constify attribute_group structures.

  compal-laptop:
   - constify attribute_group structures.

  fujitsu-laptop:
   - constify attribute_group structures.
   - add NULL check on devm_kzalloc() return value

  peaq-wmi:
   - Fix peaq_ignore_events_counter handling off by 1

  ideapad-laptop:
   - Fix indentation in DMI table
   - Add several models to no_hw_rfkill
   - Add IdeaPad V510-15IKB to no_hw_rfkill

  intel_telemetry:
   - Add debugfs entry for S0ix residency

  intel_telemetry_debugfs:
   - fix some error codes in init
   - fix oops when load/unload module"

* tag 'platform-drivers-x86-v4.13-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: silead_dmi: Add entry for Ployer Momo7w tablet touchscreen
  platform/x86: toshiba_acpi: constify attribute_group structures.
  platform/x86: asus-wmi: constify attribute_group structures.
  platform/x86: panasonic-laptop: constify attribute_group structures.
  platform/x86: alienware-wmi: constify attribute_group structures.
  platform/x86: samsung-laptop: constify attribute_group structures.
  platform/x86: compal-laptop: constify attribute_group structures.
  platform/x86: fujitsu-laptop: constify attribute_group structures.
  platform/x86: peaq-wmi: Fix peaq_ignore_events_counter handling off by 1
  platform/x86: fujitsu-laptop: add NULL check on devm_kzalloc() return value
  platform/x86: silead_dmi: Add touchscreen info for I.T.Works TW891 2-in-1
  platform/x86: ideapad-laptop: Fix indentation in DMI table
  platform/x86: ideapad-laptop: Add several models to no_hw_rfkill
  platform/x86: ideapad-laptop: Add IdeaPad V510-15IKB to no_hw_rfkill
  platform/x86: intel_telemetry: Add debugfs entry for S0ix residency
  platform/x86: intel_telemetry_debugfs: fix some error codes in init
  platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
2017-07-13 12:28:06 -07:00