commit 0736299d09 upstream.
Register read of TCPC_RX_BYTE_CNT returns the total size consisting of:
PD message (pending read) size + 1 Byte for Frame Type (SOP*)
This is validated against the max PD message (`struct pd_message`) size
without accounting for the extra byte for the frame type. Note that the
struct pd_message does not contain a field for the frame_type. This
results in false negatives when the "PD message (pending read)" is equal
to the max PD message size.
Fixes: 6f413b559f ("usb: typec: tcpci_maxim: Chip level TCPC driver")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/stable/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d%40google.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89bb3dc13a upstream.
usb core avoids sending a Set-Interface altsetting 0 request after device
reset, and instead relies on calling usb_disable_interface() and
usb_enable_interface() to flush and reset host-side of those endpoints.
xHCI hosts allocate and set up endpoint ring buffers and host_ep->hcpriv
during usb_hcd_alloc_bandwidth() callback, which in this case is called
before flushing the endpoint in usb_disable_interface().
Call usb_disable_interface() before usb_hcd_alloc_bandwidth() to ensure
URBs are flushed before new ring buffers for the endpoints are allocated.
Otherwise host driver will attempt to find and remove old stale URBs
from a freshly allocated new ringbuffer.
Cc: stable <stable@kernel.org>
Fixes: 4fe0387afa ("USB: don't send Set-Interface after reset")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250514132520.225345-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4ecdc3526 upstream.
In some cases, there is a small-time gap in which CMD_RING_BUSY can be
cleared by controller but adding command completion event to event ring
will be delayed. As the result driver will return error code.
This behavior has been detected on usbtest driver (test 9) with
configuration including ep1in/ep1out bulk and ep2in/ep2out isoc
endpoint.
Probably this gap occurred because controller was busy with adding some
other events to event ring.
The CMD_RING_BUSY is cleared to '0' when the Command Descriptor has been
executed and not when command completion event has been added to event
ring.
To fix this issue for this test the small delay is sufficient less than
10us) but to make sure the problem doesn't happen again in the future
the patch introduces 10 retries to check with delay about 20us before
returning error code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538AA45362ACCF1B94EE9B7DD96A@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acb3dac280 upstream.
The usbtmc488_ioctl_read_stb function relied on a positive return from
usbtmc_get_stb to reset the srq condition in the driver. The
USBTMC_IOCTL_GET_STB case tested for a positive return to return the stb
to the user.
Commit: <cac01bd178> ("usb: usbtmc: Fix erroneous get_stb ioctl
error returns") changed the return value of usbtmc_get_stb to 0 on
success instead of returning the value of usb_control_msg which is
positive in the normal case. This change caused the function
usbtmc488_ioctl_read_stb and the USBTMC_IOCTL_GET_STB ioctl to no
longer function correctly.
Change the test in usbtmc488_ioctl_read_stb to test for failure
first and return the failure code immediately.
Change the test for the USBTMC_IOCTL_GET_STB ioctl to test for 0
instead of a positive value.
Fixes: cac01bd178 ("usb: usbtmc: Fix erroneous get_stb ioctl error returns")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe7f7ac8e0 upstream.
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342e4955a1 upstream.
wait_event_interruptible_timeout requires a timeout argument
in units of jiffies. It was being called in usbtmc_get_stb
with the usb timeout value which is in units of milliseconds.
Pass the timeout argument converted to jiffies.
Fixes: 048c6d88a0 ("usb: usbtmc: Add ioctls to set/get usb timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a889482b upstream.
Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN).
Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN).
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f7955919 upstream.
This device exhibits I/O errors during file transfers due to unstable
link power management (LPM) behavior. The kernel logs show repeated
warm resets and eventual disconnection when LPM is enabled:
[ 3467.810740] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0020
[ 3467.810740] usb usb2-port5: do warm reset
[ 3467.866444] usb usb2-port5: not warm reset yet, waiting 50ms
[ 3467.907407] sd 0:0:0:0: [sda] tag#12 sense submit err -19
[ 3467.994423] usb usb2-port5: status 02c0, change 0001, 10.0 Gb/s
[ 3467.994453] usb 2-5: USB disconnect, device number 4
The error -19 (ENODEV) occurs when the device disappears during write
operations. Adding USB_QUIRK_NO_LPM disables link power management
for this specific device, resolving the stability issues.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250508055947.764538-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0e525d7a2 upstream.
The error handling for the case `con_index == 0` should involve dropping
the pm usage counter, as ucsi_ccg_sync_control() gets it at the
beginning. Fix it.
Cc: stable <stable@kernel.org>
Fixes: e56aac6e5a ("usb: typec: fix potential array underflow in ucsi_ccg_sync_control()")
Signed-off-by: GONG Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250107015750.2778646-1-gongruiqi1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Minor context change fixed.]
Signed-off-by: Bin Lan <bin.lan.cn@windriver.com>
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e56aac6e5a upstream.
The "command" variable can be controlled by the user via debugfs. The
worry is that if con_index is zero then "&uc->ucsi->connector[con_index
- 1]" would be an array underflow.
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/c69ef0b3-61b0-4dde-98dd-97b97f81d912@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ The function ucsi_ccg_sync_write() is renamed to ucsi_ccg_sync_control()
in commit 13f2ec3115 ("usb: typec: ucsi:simplify command sending API").
Apply this patch to ucsi_ccg_sync_write() in 6.1.y accordingly. ]
Signed-off-by: Bin Lan <bin.lan.cn@windriver.com>
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 165376f6b2 upstream.
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
[Minor conflict resolved due to code context change.]
Signed-off-by: Jianqi Ren <jianqi.ren.cn@windriver.com>
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 364618c89d upstream.
This patch introduces the ucsi_con_mutex_lock / ucsi_con_mutex_unlock
functions to the UCSI driver. ucsi_con_mutex_lock ensures the connector
mutex is only locked if a connection is established and the partner pointer
is valid. This resolves a deadlock scenario where
ucsi_displayport_remove_partner holds con->mutex waiting for
dp_altmode_work to complete while dp_altmode_work attempts to acquire it.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250424084429.3220757-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e77d3ec7c upstream.
wait_event_interruptible_timeout returns a long
The return value was being assigned to an int causing an integer overflow
when the remaining jiffies > INT_MAX which resulted in random error
returns.
Use a long return value, converting to the int ioctl return only on error.
Fixes: bb99794a47 ("usb: usbtmc: Add ioctl for vendor specific read")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9747c9b8b upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value, converting to the int ioctl return only on
error.
Fixes: 739240a9f6 ("usb: usbtmc: Add ioctl USBTMC488_IOCTL_WAIT_SRQ")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cac01bd178 upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value and convert to int ioctl return only on error.
When the return value of wait_event_interruptible_timeout was <= INT_MAX
the number of remaining jiffies was returned which has no meaning for the
user. Return 0 on success.
Reported-by: Michael Katzmann <vk2bea@gmail.com>
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054c514554 upstream.
usbtmc_read() calls usbtmc_generic_read()
which uses interruptible sleep, but usbtmc_read()
itself uses uninterruptble sleep for mutual exclusion
between threads. That makes no sense.
Both should use interruptible sleep.
Fixes: 5b775f672c ("USB: add USB test and measurement class driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250430134810.226015-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 312d79669e upstream.
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e918d3959b upstream.
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 732f35cf8b upstream.
When a USB device is connected to the OTG port, the tegra_xhci_id_work()
routine transitions the PHY to host mode and calls xhci_hub_control()
with the SetPortFeature command to enable port power.
In certain cases, the XHCI controller may be in a low-power state
when this operation occurs. If xhci_hub_control() is invoked while
the controller is suspended, the PORTSC register may return 0xFFFFFFFF,
indicating a read failure. This causes xhci_hc_died() to be triggered,
leading to host controller shutdown.
Example backtrace:
[ 105.445736] Workqueue: events tegra_xhci_id_work
[ 105.445747] dump_backtrace+0x0/0x1e8
[ 105.445759] xhci_hc_died.part.48+0x40/0x270
[ 105.445769] tegra_xhci_set_port_power+0xc0/0x240
[ 105.445774] tegra_xhci_id_work+0x130/0x240
To prevent this, ensure the controller is fully resumed before
interacting with hardware registers by calling pm_runtime_get_sync()
prior to the host mode transition and xhci_hub_control().
Fixes: f836e78430 ("usb: xhci-tegra: Add OTG support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250422114001.126367-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59820fde00 upstream.
We identified a bug where the ST_RC bit in the status register was not
being acknowledged after clearing the CTRL_RUN bit in the control
register. This could lead to unexpected behavior in the USB gadget
drivers.
This patch resolves the issue by adding the necessary code to explicitly
acknowledge ST_RC after clearing CTRL_RUN based on the programming
sequence, ensuring proper state transition.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250418081228.1194779-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8614ecdb15 upstream.
The controllers with rtl version larger than
RTL_REVISION_NEW_LPM (0x00002700) has bug which causes that controller
doesn't resume from L1 state. It happens if after receiving LPM packet
controller starts transitioning to L1 and in this moment the driver force
resuming by write operation to PORTSC.PLS.
It's corner case and happens when write operation to PORTSC occurs during
device delay before transitioning to L1 after transmitting ACK
time (TL1TokenRetry).
Forcing transition from L1->L0 by driver for revision larger than
RTL_REVISION_NEW_LPM is not needed, so driver can simply fix this issue
through block call of cdnsp_force_l0_go function.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538B55C3A6E71F9ED29E980DD842@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 241e2ce88e upstream.
In very rare cases after resuming controller from L1 to L0 it reads
registers before the clock UTMI have been enabled and as the result
driver reads incorrect value.
Most of registers are in APB domain clock but some of them (e.g. PORTSC)
are in UTMI domain clock.
After entering to L1 state the UTMI clock can be disabled.
When controller transition from L1 to L0 the port status change event is
reported and in interrupt runtime function driver reads PORTSC.
During this read operation controller synchronize UTMI and APB domain
but UTMI clock is still disabled and in result it reads 0xFFFFFFFF value.
To fix this issue driver increases APB timeout value.
The issue is platform specific and if the default value of APB timeout
is not sufficient then this time should be set Individually for each
platform.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953846C57973E4DB134CAA71DDBF2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c7973539 upstream.
Device tree bindings state that the clock is optional for UHCI platform
controllers, and some existing device trees don't provide those - such
as those for VIA/WonderMedia devices.
The driver however fails to probe now if no clock is provided, because
devm_clk_get returns an error pointer in such case.
Switch to devm_clk_get_optional instead, so that it could probe again
on those platforms where no clocks are given.
Cc: stable <stable@kernel.org>
Fixes: 26c502701c ("usb: uhci: Add clk support to uhci-platform")
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250425-uhci-clock-optional-v1-1-a1d462592f29@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64eb182d5f ]
Compatible "marvell,armada3700-xhci" match data uses the
struct xhci_plat_priv::init_quirk() function pointer to add
XHCI_RESET_ON_RESUME as quirk on XHCI.
Instead, use the struct xhci_plat_priv::quirks field.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-1-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c75f3e6a4 ]
The variable d->name, returned by devm_kasprintf(), could be NULL.
A pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b
("ice: Fix some null pointer dereference issues in ice_ptp.c").
This issue is found by our static analysis tool
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://lore.kernel.org/r/20250311012705.1233829-1-chenyuan0y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a76fcc4c ]
Nothing prevents a broken HC from claiming that an endpoint is Running
and repeatedly rejecting Stop Endpoint with Context State Error.
Avoid infinite retries and give back cancelled TDs.
No such cases known so far, but HCs have bugs.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 461f24bff8 ]
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eafba02054 ]
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41d5e3806c ]
"maxim,max3421" DT compatible is missing its SPI device ID entry, not
allowing module autoloading and leading to the following message:
"SPI driver max3421-hcd has no spi_device_id for maxim,max3421"
Fix this by adding the spi_device_id table.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20250128195114.56321-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1fdc4dca35 upstream.
wdm_wwan_port_tx_complete is called from a completion
handler with irqs disabled and possible in IRQ context
usb_autopm_put_interface can take a mutex.
Hence usb_autopm_put_interface_async must be used.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-4-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1846ed4eb upstream.
Clearing WDM_WWAN_IN_USE must be the last action or
we can open a chardev whose URBs are still poisoned
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9697f5efcf upstream.
In case submitting the URB fails we must undo
what we've done so far.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37ffdbd695 upstream.
The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3,
just like Silicon Motion Flash Drive:
https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
also needs the DELAY_INIT quirk, or it will randomly work incorrectly
(e.g.: lsusb and can't list this device info) when connecting Huawei
hisi platforms and doing thousand of reboot test circles.
Cc: stable <stable@kernel.org>
Signed-off-by: Miao Li <limiao@kylinos.cn>
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Link: https://lore.kernel.org/r/20250414062935.159024-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2932b6b547 upstream.
Silicon Motion Flash Drive connects to Huawei hisi platforms and
performs a system reboot test for two thousand circles, it will
randomly work incorrectly on boot, set DELAY_INIT quirk can workaround
this issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38d6e60b6f upstream.
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63ccd26cd1 upstream.
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb60d4385 upstream.
The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw.
MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible
keyboard/mouse interface, which confuse the OHCI controller. Since OHCI
only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR
is wrapped around (the second 4KB BAR space is the same as the first 4KB
internally). So we can add an 4KB offset (0x1000) to the OHCI registers
(from the PCI BAR resource) as a quirk.
Cc: stable <stable@kernel.org>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mingcong Bai <baimingcong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250328040059.3672979-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c531e0a8c upstream.
usb_phy_init() may return an error code if e.g. its implementation fails
to prepare/enable some clocks. And properly rollback on probe error path
by calling the counterpart usb_phy_shutdown().
Found by Linux Verification Center (linuxtesting.org).
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-4-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cab0e9a3f upstream.
Upon encountering errors during the HSIC pinctrl handling section the
regulator should be disabled.
Use devm_add_action_or_reset() to let the regulator-disabling routine be
handled by device resource management stack.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4d6141288c ("usb: chipidea: imx: pinctrl for HSIC is optional")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e28f79e3d upstream.
usbmisc is an optional device property so it is totally valid for the
corresponding data->usbmisc_data to have a NULL value.
Check that before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: 74adad5003 ("usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in the error path of .probe()")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1059896f2 upstream.
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit
58f2fcb3a8 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cc01410e1 upstream.
Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.
OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.
The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:
Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 [unknown]
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x5345 Owon
idProduct 0x1234 PDS6062T Oscilloscope
bcdDevice 1.00
iManufacturer 1 oscilloscope
iProduct 2 oscilloscope
iSerial 3 oscilloscope
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0029
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 5 Physical Interface Device
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Device Status: 0x0000
(Bus Powered)
OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.
Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling <craig@hesling.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b399078f88 upstream.
Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.
At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.
Signed-off-by: Michael Ehrenreich <michideep@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab75eee1a upstream.
Version 1.60 specifically needs this quirk.
Version 2.00 is known good.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403180004.343133-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
