This has been on my TODO list for some time now: the control that enables the video
loopback was part of the controls of the video output device instead of the video
capture device. In practice this was quite annoying since you expect it at the capture
side since that's where you want to make the decision whether to use the TPG or looped
video.
This patch moves the control from the output to the capture side.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tuner FMD1216ME_MK3 suffers the same problem as FMD1216MEX_MK3,
as described in saa7134-cards.c (disabled IF, enabled DVB-T). The
card does work under MS Windows, after soft reboot into Linux it
continues to work, only then tda9887 is loaded as well.
I copied the relevant code from the BEHOLD_H6 section to MD7134.
The CTX946 TV card doesn't detect a signal after cold boot, seems
Signed-off-by: Juergen Gier <juergen.gier@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current v4l2_of_parse_parallel_bus function attempts to parse the
DT properties for the parallel bus as well as BT656 bus.
If the pclk-sample property is defined for the BT656 bus, it is still
marked as a parallel bus.
Fix this by parsing the pclk after the bus_type is selected.
Only when hsync or vsync properties are specified, the bus_type should
be set to V4L2_MBUS_PARALLEL.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load PCTV 460e tda10071 demod and a8293 SEC using I2C client bindings.
Remove old unused tda10071 config struct. We are using I2C platform
data now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When dma-coherent transfers are enabled, the mmap call must
not change the pg_prot flags in the vma struct.
Split the arm_dma_mmap into a common and specific parts,
and add a "arm_coherent_dma_mmap" implementation that does
not alter the page protection flags.
Tested on a topic-miami board (Zynq) using the ACP port
to transfer data between FPGA and CPU using the Dyplo
framework. Without this patch, byte-wise access to mmapped
coherent DMA memory was about 20x slower because of the
memory being marked as non-cacheable, and transfer speeds
would not exceed 240MB/s.
After this patch, the mapped memory is cacheable and the
transfer speed is again 600MB/s (limited by the FPGA) when
the data is in the L2 cache, while data integrity is being
maintained.
The patch has no effect on non-coherent DMA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes the TCM initialisation code to handle TCM banks that are
present but inaccessible due to TrustZone configuration. This is
the default case when enabling the non-secure world. It may also
be the case that that the user decided to use TCM for TrustZone.
This change has exposed a bug in handling of TCM where no TCM bank
was usable (the 0 size TCM case). This change addresses the
resulting hang.
This code only handles the ARMv6 TCMTR register format, and will not
work correctly on boards that use the ARMv7 (or any other) format.
This is handled by performing an early exit from the initialisation
function when the TCMTR reports any format other than v6.
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using a toolchain with gold as the default linker, the VDSO build
fails:
VDSO arch/arm/vdso/vdso.so.raw
HOSTCC arch/arm/vdso/vdsomunge
MUNGE arch/arm/vdso/vdso.so.dbg
OBJCOPY arch/arm/vdso/vdso.so
BFD: arch/arm/vdso/vdso.so: Not enough room for program headers, try
linking with -N
For whatever reason, ld.gold is omitting an exidx program header that
ld.bfd emits, and even when I work around that, I don't get a working
VDSO.
For now, instead of supporting gold (which will fail to link the
kernel anyway since it does not implement --pic-veneer), direct the
compiler to use the traditional bfd linker. This is accomplished by
using -fuse-ld, which is implemented in GCC 4.8 and later.
Note: one limitation of this is that if the toolchain is configured
to use gold by default, and the bfd linker is not in $PATH, the VDSO
build will fail:
VDSO arch/arm/vdso/vdso.so.raw
collect2: fatal error: cannot find 'ld'
This will happen if CROSS_COMPILE begins with a path such as
/opt/bin/arm-linux-gnu- but /opt/bin is not in $PATH. This is
considered an acceptable corner-case limitation and is easily worked
around.
Additonal note: we use cc-option instead of cc-ldoption so that
-fuse-ld=bfd is placed in the command line if the compiler recognizes
the option. Using cc-ldoption results in an attempt to link, which
fails in the situation just described, causing -fuse-ld=bfd to be
omitted and gold to be used for the VDSO link, which is what we're
trying to prevent.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the VDSO's link options are kind of a mess spread between
ccflags-y and cmd_vdsold. Collect linker directives into one
variable, VDSO_LDFLAGS, and use that in cmd_vdsold.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix possible unintended sign extension in unsigned MMIO loads by casting
to uint16_t in the case of mmio_needed != 2.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix stack pointer offset which could potentially corrupt
argument registers in the previous frame. The calculated offset
reflects the size of all the registers we need to preserve so there
is no need for this erroneous subtraction.
[ralf@linux-mips.org: Fixed conflict due to only applying this fix part
of the entire series as part of 4.1 fixes.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/10527/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
setup_per_cpu_areas() only setup __per_cpu_offset[] for each possible
cpu, but loongson_sysconf.nr_cpus can be greater than possible cpus
(due to reserved_cpus_mask). So in loongson3_ipi_interrupt(), percpu
access will touch the original varible in .data..percpu section which
has been freed. Without this patch, cpu-hotplug will cause memery
corruption.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/10524/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 334c86c494 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
Fixes: 334c86c494 ("MIPS: IRQ: Add stackoverflow detection")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Adam Jiang <jiang.adam@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 2.6.37+
Patchwork: http://patchwork.linux-mips.org/patch/10531/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
addr can be NULL and it should not be dereferenced before NULL checking.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Correct locking and refcounting in tracking our rports
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use btbcm helpers to perform controller setup.
Perform host UART reset to init speed between btbcm_patchram() and
btbcm_finalize(). This may be need because firmware loading may have
reseted controller UART to init speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.
UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
firmware name as parameter, requests the firmware and loads it to
the controller.
- btbcm_finalize() which resets the controller, reads local version
and checks if the controller address is a default one or not.
Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The patch e85c9a7abf: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
Free VI, flush sge ec and some other misc. fixes
This patch series adds the following.
Free VI interface during remove, flush SGE ec routine, rename
t4_link_start to t4_link_l1cfg since it only does l1 configuration, set
mac addr from when we can't contact firmware for debug purpose, set pcie
completion timeout and use fw interface to access TP_PIO_XXX registers
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab the Adapter MAC Address out of the VPD and use it for the "debug"
network interface when either we can't contact the firmware
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-04
This series contains updates to i40e and i40evf.
Anjali provides three fixes, first to resolve a Tx queue hang if mixed
size frags are passed to the driver while using TSO. There was a corner
case where we needed to linearize but we were not. Next fixes a bug in
the default configuration which prevented a software bridge loaded on the
PF interface from working correctly because broadcast packets are
incorrectly looped back. Lastly fixes an NPAR bug when SRIOV is enabled,
where we need to be in VEB mode, not VEPA mode at probe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 84cb7be43c broke vivid-tpg
(uninitialized variable p).
This patch takes a different approach: four different functions are
created, one for each PRINTSTR version.
In order to avoid the 'the frame size of 1308 bytes is larger than 1024
bytes' warning I had to mark those functions with 'noinline'. For
whatever reason gcc seems to inline this aggressively and it is doing
weird things with the stack.
I tried to read the assembly code, but I couldn't see what exactly it
was doing on the stack.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CFQ idling causes reduced IOPS throughput on non-rotational disks.
Since disk head seeking is not applicable to SSDs, it doesn't really
help performance by anticipating future near-by IO requests.
By turning off idling (and switching to IOPS mode), we allow other
processes to dispatch IO requests down to the driver and so increase IO
throughput.
Following FIO benchmark results were taken on a cloud SSD offering with
idling on and off:
Idling iops avg-lat(ms) stddev bw
------------------------------------------------------
On 7054 90.107 38.697 28217KB/s
Off 29255 21.836 11.730 117022KB/s
fio --name=temp --size=100G --time_based --ioengine=libaio \
--randrepeat=0 --direct=1 --invalidate=1 --verify=0 \
--verify_fatal=0 --rw=randread --blocksize=4k --group_reporting=1 \
--filename=/dev/sdb --runtime=10 --iodepth=64 --numjobs=10
And the following is from a local SSD run:
Idling iops avg-lat(ms) stddev bw
------------------------------------------------------
On 19320 33.043 14.068 77281KB/s
Off 21626 29.465 12.662 86507KB/s
fio --name=temp --size=5G --time_based --ioengine=libaio \
--randrepeat=0 --direct=1 --invalidate=1 --verify=0 \
--verify_fatal=0 --rw=randread --blocksize=4k --group_reporting=1 \
--filename=/fio_data --runtime=10 --iodepth=64 --numjobs=10
Reviewed-by: Nauman Rafique <nauman@google.com>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Extend xen/block to support multi-page ring, so that more requests can be
issued by using more than one pages as the request ring between blkfront
and backend.
As a result, the performance can get improved significantly.
We got some impressive improvements on our highend iscsi storage cluster
backend. If using 64 pages as the ring, the IOPS increased about 15 times
for the throughput testing and above doubled for the latency testing.
The reason was the limit on outstanding requests is 32 if use only one-page
ring, but in our case the iscsi lun was spread across about 100 physical
drives, 32 was really not enough to keep them busy.
Changes in v2:
- Rebased to 4.0-rc6.
- Document on how multi-page ring feature working to linux io/blkif.h.
Changes in v3:
- Remove changes to linux io/blkif.h and follow the protocol defined
in io/blkif.h of XEN tree.
- Rebased to 4.1-rc3
Changes in v4:
- Turn to use 'ring-page-order' and 'max-ring-page-order'.
- A few comments from Roger.
Changes in v5:
- Clarify with 4k granularity to comment
- Address more comments from Roger
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The major responsibility of talk_to_blkback() is allocate and initialize
the request ring and write the ring info to xenstore.
But this work should be done after backend entered 'XenbusStateInitWait' as
defined in the protocol file.
See xen/include/public/io/blkif.h in XEN git tree:
Front Back
================================= =====================================
XenbusStateInitialising XenbusStateInitialising
o Query virtual device o Query backend device identification
properties. data.
o Setup OS device instance. o Open and validate backend device.
o Publish backend features and
transport parameters.
|
|
V
XenbusStateInitWait
o Query backend features and
transport parameters.
o Allocate and initialize the
request ring.
There is no problem with this yet, but it is an violation of the design and
furthermore it would not allow frontend/backend to negotiate 'multi-page'
and 'multi-queue' features.
Changes in v2:
- Re-write the commit message to be more clear.
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
