MIC card driver specific changes to enable SCIF. This patch implements
the SCIF hardware bus operations and registers a SCIF device on the
SCIF hardware bus.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIC host driver specific changes to enable SCIF. This patch implements
the SCIF hardware bus operations and registers a SCIF device on the
SCIF hardware bus.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF messaging APIs which allow sending messages between the SCIF
endpoints via a byte stream based ring buffer which has been
optimized to avoid reads across PCIe. The SCIF messaging APIs
are typically used for short < 1024 byte messages for best
performance while the RDMA APIs which will be submitted in a future
patch series is recommended for larger transfers. The node
enumeration API enables a user to query for the number of nodes
online in the SCIF network and their node ids.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF connection APIs which establish a SCIF connection between
a pair of SCIF endpoints. A SCIF connection consists of a
dedicated queue-pair between the endpoints. Client messages are
sent over the queue-pair whereas the signaling associated with the
message is multiplexed over the node queue-pair. Similarly other
control messages such as exposing registered memory are also sent
over the node queue-pair. The SCIF endpoints must be in connected
state to exchange messages, register memory, map remote memory and
trigger DMA transfers. SCIF connections can be set up
asynchronously or synchronously.
Thanks to Johnnie S Peters for authoring parts of this patch during
early bring up of the SCIF driver.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF character device file operations and kernel APIs for opening and
closing a user and kernel mode SCIF endpoint. This patch also enables
binding to a SCIF port and listening for incoming SCIF connections.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF node queue pair setup creates the SCIF driver kernel
mode private node queue pairs between all the nodes to enable
internal control message communication once SCIF gets probed
by the SCIF hardware bus. Peer to peer communication between
MIC Coprocessor nodes is supported.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF module initialization, DMA mapping, ioremap wrapper APIs
and debugfs hooks. SCIF gets probed by the SCIF hardware bus
if SCIF devices were registered by base drivers. A MISC device
is registered to provide the SCIF character device interface.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update mic_bootparam and define the maximum number of DMA channels
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCIF peer bus is used to register and unregister SCIF peer devices
internally by the SCIF driver to signify the addition and removal of
peer nodes respectively from the SCIF network. This simplifies remote node
handling within SCIF and will also be used to support device probe/remove
for SCIF client drivers (e.g. netdev over SCIF)
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCIF hardware bus abstracts the low level hardware driver details
like interrupts and mapping remote memory so that the same SCIF driver
can work without any changes with the MIC host or card driver as long
as the hardware bus operations are implemented. The SCIF hardware
device is registered by the host and card drivers on the SCIF hardware
bus resulting in probing the SCIF driver.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF ring buffer is a single producer, single consumer byte stream
ring buffer optimized for avoiding reads across the PCIe bus while
adding the required barriers and hardware workarounds for the MIC
Coprocessor. The ring buffer is used to implement a receive queue for
SCIF driver messaging between two nodes and for byte stream messaging
between SCIF endpoints. The existing in-kernel ring buffer was not
reused since it has not been designed for our use across the PCIe bus
where each node runs an independent OS. Each SCIF node has a receive
queue for every other SCIF node, and each connected endpoint has a
receive queue for messages from its peer. This pair of receive
queues is referred to as a SCIF queue pair.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the SCIF documentation in the header file
and describes the IOCTL interface for user mode. mic_overview.txt
is updated with documentation on SCIF and a new document
describing SCIF in more details is available in scif_overview.txt.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CARMA project has ended, and the hardware has all been moved into
storage. It is unlikely to ever be used again.
Remove the drivers so that there is no more maintenance burden from
ongoing upstream kernel changes.
Signed-off-by: Ira W. Snyder <ira.snyder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove trailing whitespace from several lines in drivers/char/misc.c
This was done using scripts/cleanfile
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides support for the DS28EA00 digital thermometer.
The DS28EA00 provides an additional two pins for implementing a sequence
detection algorithm. This feature allows you to determine the physical
location of the chip in the 1-wire bus without needing pre-existing
knowledge of the bus ordering. Support is provided through the sysfs
w1_seq file. The file will contain a single line with an integer value
representing the device index in the bus starting at 0.
Signed-off-by: Matt Campbell <mattrcampbell@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A temperature conversion can take 750 ms and when possible the
w1_therm slave driver drops the bus_mutex to allow other bus
operations, but that includes operations such as a periodic slave
search, which can remove this slave when it is no longer detected.
If that happens the sl->family_data will be freed and set to NULL
causing w1_slave_show to crash when it wakes up.
Signed-off-by: David Fries <David@Fries.net>
Reported-By: Thorsten Bschorr <thorsten@bschorr.de>
Tested-by: Thorsten Bschorr <thorsten@bschorr.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of 1-Wire devices commonly associated with physical access control
systems are attached/generate presence for as short as 100 ms - hence
the tens-to-hundreds milliseconds scan intervals are required.
Signed-off-by: Dmitry Khromov <dk@icelogic.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, on x86_64, decompression fails with the following
error:
Decompressing Linux...
Decoding failed
-- System halted
This condition is not needed for a 64bit kernel(from commit d5e7caf):
if( ... ||
(op + COPYLENGTH) > oend)
goto _output_error
macro LZ4_SECURE_COPY() tests op and does not copy any data
when op exceeds the value.
added by analogy to lz4_uncompress_unknownoutputsize(...)
Signed-off-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Tested-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Tested-by: Caleb Jorden <cjorden@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all architectures have io memory.
Fixes:
drivers/built-in.o: In function `spmi_pmic_arb_probe':
spmi-pmic-arb.c:(.text+0x1ed399): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UIO base driver should only free_irq that it has requested.
UIO supports drivers without interrupts (irq == 0) or custom handlers.
This fixes warnings like:
WARNING: CPU: 1 PID: 5478 at kernel/irq/manage.c:1244 __free_irq+0xa9/0x1e0()
Trying to free already-free IRQ 0
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uX2k
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
* twl6030-gpadc - Drop a bonus space from the modalias.
* adis16400 - Report pressure channel scale (not much use without it)
- Use different channel indices for the two voltage channels (ABI)
- Compute the san mask from the channel indices instead of using
~0UL as we now care about extra bits being set.
- Fix burst mode due to rx buffer not being intialized and wrong
tx buffer type being set. Also had the wrong transfer length.
All in all it didn't work, now it does ;)
- adis16448 has additional registers in burst mode so we skip
over them to make it work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nM+v
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of fixes for IIO in the 4.1 cycle.
* twl6030-gpadc - Drop a bonus space from the modalias.
* adis16400 - Report pressure channel scale (not much use without it)
- Use different channel indices for the two voltage channels (ABI)
- Compute the san mask from the channel indices instead of using
~0UL as we now care about extra bits being set.
- Fix burst mode due to rx buffer not being intialized and wrong
tx buffer type being set. Also had the wrong transfer length.
All in all it didn't work, now it does ;)
- adis16448 has additional registers in burst mode so we skip
over them to make it work.
1. mei_nfc_hci_hdr and mei_nfc_hdr are just the same thing so drop one
2. use mei_nfc_hdr structure as the member of the command and the reply
instead of replicating all header fields.
3. dump the header for easier debugging
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since we move all nfc hanling to the mei_phy module
we can kill mei_cl_ops
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
move nfc logic to mei_phy module, we prefer as much as
possible not to deal with a particualr client protocol
in the mei generic infrasutcutre
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export name and uuid via sysfs and uevent
Cc: linux-api@vger.kernel.org
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to automate modules matching add device uuid
which is reported in client enumeration, keep also
the name that is needed in for nfc distinguishing radio vendor
Report mei:name:uuid
Cc: linux-api@vger.kernel.org
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The io callback is clear from write_waitling_list after
we receive interrupt from the hw to ack the write completion.
We need to wait for this interrupt deliver before we try
to enter low power state
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On longer non-blocking write might not complete at the end of
autosuspend expiration, therefore we request autosuspend
again on the write completion.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consume the write flow control on the first chunk of the write instead
of on the buffer completion.
We can safely assume that the consequent chunks have the flow control
granted.
This addresses two issues:
1. Blocks other callbacks from the same client riding on the client's
flow control and prevents interleaving of messages as FW cannot distinguish
between two messages from the same client.
2. Fixes single buffer flow control arbitration in a clean way, without
connection/disconnection book keeping
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a set of five fixes: Two MAINTAINER email updates (urgent because the
non-avagotech emails will start bouncing) an lpfc big endian oops fix, a 256
byte sector hang fix (to eliminate 256 byte sectors) and a storvsc fix which
could cause test unit ready failures on bringup.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVYPemAAoJEDeqqVYsXL0MK8UIAJJ8ViLPTfhweb8QgHsUjc4S
5x2jPUD69XT93G81NWKvFhYBnlAvktBZuy6uON7SkLWkbwgiu3pB1Iowqie+Z/h8
1C5VwC8oaT6GZPuakRRxnYmoAaCX7kbdMsibSvc5ouTgvM5FdailhJpkDKcFQlkn
t1GqmRQyH1P54O73af2d+z3AfNfivjoFFXz1YHcUOouiKBVyXzqk1c3CIwTQMelg
B547Rz2cqgdDtgQzZzPkfust/GOYs0ZQMU3rhjeNyIvw/5xa0/Ta2m/v16lckV2I
AvjK2Ht5XSr/Hc9m4yvr5vYCT5+mVrebYMghnUqpHjx1OGTBSU9lPT0exbCCJ/o=
=lXOs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Add client info to debug prints in the read function to
ease on debugging efforts.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can receive mtu with one call now, no need to store it.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be used for debug only.
The feaure is gated by "allow_fixed_address" control exposed in debugfs.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed address is simplified FW client that doesn't require
connection and doesn't support flow control.
So it can be only one host client per fixed FW client.
Fixed client access is available only for drivers on mei bus,
connection from user-space is blocked.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ME clients that use single receiving buffer
the driver tracks credentials on mei_me_clients structure
for all connections. The driver needs to book keep the shared
resource correctly and track the connections, particularly
the credit has to be cleaned when there is no active connection
to a particular me client. This solves issue when subsequent
connection will not get an ill impression that it can write.
We add active connection counter the particular ME client and
when the counter reach zero, we clear the credits.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep a pointer to associated me client in the host client object to
eliminate me client searches. Check if the me client is active in the
firmware by checking if its is linked on the me clients list
Add accessors for the me client properties from host client.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify connect state machine by changing the logic around
Connection request in progress - only check if we have a callback in
relevant queue.
Extract common code into mei_cl_send_connect() function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split disconnected state into two parts first reception disconnect
response from the firmware and second actually setting of disconnected
state. Book keeping data are needed for processing and after firmware
disconnected the client and are cleaned when setting the disconnected
state in mei_cl_set_disconneted() function.
Add mei_cl_send_disconnect to reduce code duplication.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.
Cc: <stable@vger.kernel.org> #3.18+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Barak Yoresh <barak.yoresh@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver manages Qualcomm CoreSight Replicator device, which
resides on the AMBA bus. Replicator has been made programmable to
allow software to turn of the replicator branch to sink that is not
being used. This avoids trace traffic to the unused/non-current sink
from causing back pressure that results in overflows at the source.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put in a blurb in the device tree bindings indicating that
coresight blocks may have an optional ATCLK.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-4 the funnel has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.
The ATCLK is enabled and disabled using the runtime PM
callbacks. As the replicator is a platform device, the
code is a bit different from the other CoreSight components
and the bus core does not activate runtime PM by default,
so we need a few extra calls.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-6 the funnel has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.
The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-8 the ETB has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.
The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
