The code was a bit convoluted. Clean it up and
prepare for future changes.
While at it this fixes incorrect verification of
'single nss' case when ss2 rates were missing
while ss1 and ss3 were requested resulting in
nss=3 being set:
iw wlan1 set bitrates legacy-5 ht-mcs-5 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23 vht-mcs-5 1:0-9 3:0-9
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of 3 vdevs wasn't enough to handle the
worst case for interface combinations in practice.
wpa_supplicant may need up to 4 vifs to have 2
vifs actually connected, i.e. p2pdev + client + 2x
p2p (either p2p client or p2p go).
This fixes worst case warning:
Free vdev map is empty, no more interfaces allowed.
This keeps the ability to associate 32 stations in
AP mode at the cost of not being able to guarantee
that under all circumstances, i.e. some
combinations may consume additional fw peer
entries for internal purposes leaving less
resource for stations in AP mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This effectively enables multi-channel operation
on qca6174 WLAN.RM.2.0-00073 (and possibly any
newer firmware release for qca6174).
This adds appopriate interface combinations and
initializes firmware channel scheduler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 wmi-tlv firmware defines a new wmi event
for host tx pausing (i.e. stop/wake tx queues).
Map these events to ath10k/mac80211 tx queue
control.
This is important for multi-channel throughput
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reject a valid
firmware configuration combination.
Since SSID isn't known early on it might make
sense to allow driver to start vdev without SSID
and restart it later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This contains fixes for:
* A VT-d issue where hardware domain-ids might be freed while
still in use.
* An ipmmu-vmsa issue where where the device-table was not zero
terminated
* Unchecked register access issue in the arm-smmu driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=P6CS
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"This contains fixes for:
- a VT-d issue where hardware domain-ids might be freed while still
in use.
- an ipmmu-vmsa issue where where the device-table was not zero
terminated
- unchecked register access issue in the arm-smmu driver"
* tag 'iommu-fixes-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Remove unused variable
iommu: ipmmu-vmsa: Add terminating entry for ipmmu_of_ids
iommu/vt-d: Detach domain *only* from attached iommus
iommu/arm-smmu: fix ARM_SMMU_FEAT_TRANS_OPS condition
Since commit 8e70946943 ("lguest: add a dummy PCI host bridge.")
lguest uses PCI, but it needs you to frob the ports directly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
qca6174 and wmi-tlv doesn't have quiet mode
implemented. Don't even attempt to call it. This
fixes a warning when bringing first interface up:
failed to set quiet mode period 100 duarion 0 enabled 0 ret -95
Fixes: 8515b5c79a ("ath10k: configure thermal throttle while powering up")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All of the bringup/init functions called in ath10k_core_start return 0
on success and != 0 on failure. ath10k_wmi_wait_for_service_ready(),
ath10k_wmi_wait_for_unified_ready() and their call sites were adjusted
to fit this model.
The return type of wait_for_completion_timeout is unsigned long not int so
ath10k_wmi_wait_for_service_ready() and ath10k_wmi_wait_for_unified_ready()
were fixed up accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Missing spaces 1*HZ -> 1 * HZ were also added along the way.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, respectively 'ret'
renamed, and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVGx6pAAoJEPL5WVaVDYGjh5cIAKQAyGST92IbTkxRZsxMgqnH
7LQI+fbNn6oHGEjSSnsWLxl6CpwT4WrCmj8WhVmpAoTLU958nBbF7iZAaaeQCGeS
3EqaNOlKvuOK9M5PKK7a5AWO04uJuj+t6s536OqHyB1zRb1yYMsywllPzu63eigA
jxu2yZxkFIKjo2ohSaTDRONVCsQGlqgZ2Aq/Ho5vy5QffVJKTN1G/3Kf33xukUyr
SAnndaax23jMqcFJE3gePYXc3W8EuGoloehKyo04qFeNNVMmSoytXAwMzcTmHn+H
biOTN5ezSKbYzv1aevRg7UuSPv17/yIo3aEberfLBgsn5O4wJGDdS+LajaI5/x8=
=0k0d
-----END PGP SIGNATURE-----
Merge tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull lazytime fixes from Ted Ts'o:
"This fixes a problem in the lazy time patches, which can cause
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours"
* tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fs: add dirtytime_expire_seconds sysctl
fs: make sure the timestamps for lazytime inodes eventually get written
When we access the triggers we need to make sure that the
data we expect was actually provided by the firmware file.
Check this when we decode the triggers from the firmware
file.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull nfsd fixes from Bruce Fields:
"Two main issues:
- We found that turning on pNFS by default (when it's configured at
build time) was too aggressive, so we want to switch the default
before the 4.0 release.
- Recent client changes to increase open parallelism uncovered a
serious bug lurking in the server's open code.
Also fix a krb5/selinux regression.
The rest is mainly smaller pNFS fixes"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: make debugfs file creation failure non-fatal
nfsd: require an explicit option to enable pNFS
NFSD: Fix bad update of layout in nfsd4_return_file_layout
NFSD: Take care the return value from nfsd4_encode_stateid
NFSD: Printk blocklayout length and offset as format 0x%llx
nfsd: return correct lockowner when there is a race on hash insert
nfsd: return correct openowner when there is a race to put one in the hash
NFSD: Put exports after nfsd4_layout_verify fail
NFSD: Error out when register_shrinker() fail
NFSD: Take care the return value from nfsd4_decode_stateid
NFSD: Check layout type when returning client layouts
NFSD: restore trace event lost in mismerge
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Moreover use devm_gpiod_get_optional instead of ignoring all errors
returned by devm_gpiod_get and simplify accordingly.
The result is more strict error handling which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tty_name member of struct ser_device is never set or used, so it
can be removed. (The definition of struct ser_device is private to
this .c file, and the identifier tty_name only occurs in this one
place.)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu and memory hotplug scripts use the same name. Change
memory on-off-test.sh to mem-on-off-test.sh.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpu and memory hotplug scripts use the same name. Change
cpu on-off-test.sh to cpu-on-off-test.sh.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ahci_st driver will hang the system on probe, as the
st_configure_oob function does some register writes before the IP
is clocked. This patch moves the function call to after
ahci_platform_enable_resources (which enables the IP clock), and
resolves the hang.
Addtionally st_ahci_configure_oob should be called in the st_ahci_resume
function, so we also rectify that ensuring it is also called after
the IP clock has been enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As part of testing ahci_st driver working on stih407 I noticed
several things wrong in the DT documentation: -
1) Compatible string doesn't match the driver code
2) pwr-rst reset isn't documented (but exists in the driver)
3) some whitespace issues (spaces not tabs)
Also add in a stih407 family example into the doc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The example is wrong in that the phys property should take a
phandle to the phy port.
Also with the changing over to generic PHY type constants we also
update that as well.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch marks functions llog_cat_set_first_idx and cat_cancel_cb
static as these are used only within this file. Also since cat_cancel_cb
is made static do not export it.
This eliminates the following sparse warning:
warning: symbol * was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes functions mgc_logname2resid, mgc_set_info_async
and mgc_init static as these are only used internally.
This also eliminates sparse warnings of the type:
warning: symbol * was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header file mdc_internal.h that declares the
function lprocfs_mdc_init_vars.
This also eliminates the sparse warning:
warning: symbol 'lprocfs_mdc_init_vars' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header lustre/include/lclient.h that declares
the functions lov_lsm_put and lov_read_and_clear_async_rc defined in
lov_object.c.
This eliminates warnings reported by sparse:
warning: symbol was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header file lmv_internal.h that declares
the function lprocfs_lmv_init_vars defined in lproc_lmv.c.
This eliminates the sparse warning:
warning: symbol 'lprocfs_lmv_init_vars' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function obd_proc_version_seq_show is only used in this
file, so make it static.
This eliminates the following sparse warning:
warning: symbol 'obd_proc_version_seq_show' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count the number of requests in a ring for the user and show who
submitted them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle VERSION Rx protocol packets. We should respond to a VERSION packet
with a string indicating the Rx version. This is a maximum of 64 characters
and is padded out to 65 chars with NUL bytes.
Note that other AFS clients use the version request as a NAT keepalive so we
need to handle it rather than returning an abort.
The standard formulation seems to be:
<project> <version> built <yyyy>-<mm>-<dd>
for example:
" OpenAFS 1.6.2 built 2013-05-07 "
(note the three extra spaces) as obtained with:
rxdebug grand.mit.edu -version
from the openafs package.
Signed-off-by: David Howells <dhowells@redhat.com>
Sparse reported the following warnings:
warning: symbol 'lstcon_console_init' was not declared. Should it be static?
warning: symbol 'lstcon_console_fini' was not declared. Should it be static?
warning: symbol 'lstcon_ioctl_entry' was not declared. Should it be static?
However since these functions are used in other files,
they cannot be made static, so add protoypes for the same in console.h.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete duplicated argument to | for the state argument in
the _clr_fwstate_() function call as it is redundant.
Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user() to avoid its duplicated implementation and simplify
code. memdup_user() uses GFP_KERNEL instead of GFP_ATOMIC,
which is valid because copy_from_user() might sleep and it's useless
to make the allocation atomic. Found with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Place driver on standby mode on error in order to prevent wasting
power. Move standby function above to be seen by the new call.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and writes it in its
shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and replaces it with
its shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and replaces it
with its shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
