We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
which depends on MMC_CAP_RUNTIME_RESUME capability.
On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.
And the total tuning time will be more than 400ms.
So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to cap "ucontrol->id.index / num_busses_in(chip)" so the we
don't read beyond the end of the array.
I also adding a check on "in" and changing the type in
snd_echo_mixer_put() from short to unsigned int. Those changes are done
for symmetry and are cosmetic.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"err" is always a negative error code here, so there is no point in
checking. Removing the check silences a static checker warning and
makes the code a bit more clear. Also we don't need to initialize "err".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When ioremap_wc() or ioremap_cached() are used without first including
asm/pgtable.h, the _PAGE_CACHEABLE or _PAGE_WR_COMBINE definitions
aren't found, resulting in build errors like the following (in
next-20150323 due to "lib: devres: add a helper function for
ioremap_wc"):
lib/devres.c: In function ‘devm_ioremap_wc’:
lib/devres.c:91: error: ‘_PAGE_WR_COMBINE’ undeclared
We can't easily include asm/pgtable.h in asm/io.h due to dependency
problems, so split out the _PAGE_* definitions from asm/pgtable.h into a
separate asm/pgtable-bits.h header (as a couple of other architectures
already do), and include that in io.h instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 16bit COEF read/write is pretty standard for many codecs, and they
can be cached in most cases -- more importantly, they need to be
restored at resume. For making this easier, add the cache support to
regmap. If the codec driver wants to cache the COEF access, set
codec->cache_coef flag and issue AC_VERB_GET_PROC_COEF with the coef
index in LSB 8 bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio has quite a few asymmetrical ways of accessing verbs, and one
of typical ones is GET/SET_POWER_STATE verbs. While it takes only the
power state for setting, it returns a combination of states for
getting. For making the state handling simpler, this patch adds a
code to translate the value returned from GET_POWER_STATE to return
only the actual state or -1 for error. In that way, the driver can
simplify the power state management.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio spec is inconvenient regarding the handling of stereo volume
controls. It can set and get only single channel at once (although
there is a special option to set the same value to both channels).
This patch provides a fake pseudo-register via the regmap access so
that the stereo channels can be read and written by a single call.
It'd be useful, for example, for implementing DAPM widgets.
A stereo amp pseudo register consists of the encoding like the normal
amp verbs but it has both SET_LEFT (bit 13) and SET_RIGHT (bit 12)
bits set. The regmap reads and writes a 16bit value for this pseudo
register where the upper 8bit is for the right chanel and the lower
8bit for the left channel.
Note that the driver doesn't recognize conflicts when both stereo and
mono channel registers are mixed. Mixing them would certainly confuse
the operation. So, use carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target. But this conversion
needs a bit more caution than before.
- In the old code, we just record any verbs as is, and restore them at
resume. For the regmap scheme, this doesn't work, since a few verbs
like AMP or DIGI_CONVERT are asymmetrical. Such verbs are converted
either to the dedicated function (snd_hda_regmap_xxx_amp()) or
changed to the unified verb.
- Some verbs have to be declared as vendor-specific ones before
accessing via regmap.
Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation. Further
optimizations will be brought in the later patches, if any.
This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codecs may have own vendor-specific verbs, and we need to allow each
driver to give such verbs for cached accesses. Here a verb can be put
into a single array and looked through it at readable and writeable
callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table. Now it's
dropped by the regmap's cache.
The only tricky conversion is snd_hda_codec_amp_init(). This function
shouldn't do anything if the amp was already initialized. For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode. Only if it returns an error, i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overriding exec_verb op to struct hdac_device so that the call
via snd_hdac_exec_verb() can switch to a different route depending on
the setup. The codec driver sets this field so that it can handle the
errors or applying quirks appropriately. Furthermore, this mechanism
will be used for smooth transition for the regmap support in later
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use %pS for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pF expects a function descriptor.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch modifies the HYP init code so it can deal with system
RAM residing at an offset which exceeds the reach of VA_BITS.
Like for EL1, this involves configuring an additional level of
translation for the ID map. However, in case of EL2, this implies
that all translations use the extra level, as we cannot seamlessly
switch between translation tables with different numbers of
translation levels.
So add an extra translation table at the root level. Since the
ID map and the runtime HYP map are guaranteed not to overlap, they
can share this root level, and we can essentially merge these two
tables into one.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The page size and the number of translation levels, and hence the supported
virtual address range, are build-time configurables on arm64 whose optimal
values are use case dependent. However, in the current implementation, if
the system's RAM is located at a very high offset, the virtual address range
needs to reflect that merely because the identity mapping, which is only used
to enable or disable the MMU, requires the extended virtual range to map the
physical memory at an equal virtual offset.
This patch relaxes that requirement, by increasing the number of translation
levels for the identity mapping only, and only when actually needed, i.e.,
when system RAM's offset is found to be out of reach at runtime.
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Rework of the KVM HYP bounce page from Ard Biesheuvel. Subsequent arm64
idmap rework depends on this, so merge it here with Marc Zyngier's
blessing (kvm-arm co-maintainer).
Make the code which sets up the pmd depend on PT_NLEVELS == 3, not on
CONFIG_64BIT. The reason is, that a 64bit kernel with a page size
greater than 4k doesn't need the pmd and thus has PT_NLEVELS = 2.
Signed-off-by: Helge Deller <deller@gmx.de>
The patch dc6c9a35b6 that counts pmds
allocated for a process introduced a bug on 64-bit PA-RISC kernels.
The PA-RISC architecture preallocates one pmd with each pgd. This
preallocated pmd can never be freed - pmd_free does nothing when it is
called with this pmd. When the kernel attempts to free this preallocated
pmd, it decreases the count of allocated pmds. The result is that the
counter underflows and this error is reported.
This patch fixes the bug by artifically incrementing the counter in
pmd_free when the kernel tries to free the preallocated pmd.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 06f75a1f62 ("ARM, arm64: kvm: get rid of the bounce
page") uses ld's builtin function LOG2CEIL() to align the
KVM init code to a log2 upper bound of its size. However,
this function turns out to be a fairly recent addition to
binutils, which breaks the build for older toolchains.
So instead, implement a replacement LOG2_ROUNDUP() using
the C preprocessor.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
"hdev->req->nbytes" is an unsigned int so we so we lose the upper 3 bits
to the shift wrap bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GCC complains about that %u is the wrong format string for size_t and
also that "ret" is unused.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert pr_info() and pr_err() log messages to dev_info() and dev_err(),
respectively, where able. This adds the module name and PCI B:D:F to
indicate which QAT device generated the log message. The "QAT:" is removed
from these log messages as that is now unnecessary. A few of these log
messages have additional spelling/contextual fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This define is a duplicate of the one in ./include/linux/pci_ids.h
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Kconfig entry for CRYPTO_DEV_IMGTEC_HASH incorrectly selects
CRYPTO_SHA224, which does not exist (and is covered by CRYPTO_SHA256
which covers both 224 and 256). Remove it.
Also correct typo CRYPTO_ALG_API to be CRYPTO_ALGPI.
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This allows us to remove some unnecessary ifdefs. There should
be no change to the generated code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f7e00f0d668e253abf0bd8bf36491ac47bd761ff.1426728647.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
user_mode_vm() and user_mode() are now the same. Change all callers
of user_mode_vm() to user_mode().
The next patch will remove the definition of user_mode_vm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/43b1f57f3df70df5a08b0925897c660725015554.1426728647.git.luto@kernel.org
[ Merged to a more recent kernel. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
user_mode() is now identical to user_mode_vm(). Subsequent patches
will change all callers of user_mode_vm() to user_mode() and then
delete user_mode_vm().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/0dd03eacb5f0a2b5ba0240de25347a31b493c289.1426728647.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A few of the user_mode() checks in traps.c are immediately after
explicit checks for vm86 mode. Change them to user_mode_ignore_vm86().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/0b324d5b75c3402be07f8d3c6245ed7f4995029e.1426728647.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's no point in checking the VM bit on 64-bit, and, since
we're explicitly checking it, we can use user_mode_ignore_vm86()
after the check.
While we're at it, rearrange the #ifdef slightly to make the code
flow a bit clearer.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/dc1457a734feccd03a19bb3538a7648582f57cdd.1426728647.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
user_mode() is dangerous and user_mode_vm() has a confusing name.
Add user_mode_ignore_vm86() (equivalent to current user_mode()).
We'll change the small number of legitimate users of user_mode()
to user_mode_ignore_vm86().
Inspired by grsec, although this works rather differently.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/202c56ca63823c338af8e2e54948dbe222da6343.1426728647.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
