I forgot to use write_pnet() in three locations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 33cf7c90fe ("net: add real socket cookies")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to retain the route preference when RAs are handled in
userspace.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flags are used in the return path rather than the return patch.
Fixes: af33c1adae ("vxlan: Eliminate dependency on UDP socket in transmit path")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem in netlink socket dumps is the use
of kernel socket addresses as cookies.
1) It is a security concern.
2) Sockets can be reused quite quickly, so there is
no guarantee a cookie is used once and identify
a flow.
3) request sock, establish sock, and timewait socks
for a given flow have different cookies.
Part of our effort to bring better TCP statistics requires
to switch to a different allocator.
In this patch, I chose to use a per network namespace 64bit generator,
and to use it only in the case a socket needs to be dumped to netlink.
(This might be refined later if needed)
Note that I tried to carry cookies from request sock, to establish sock,
then timewait sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric Salo <salo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we merged the tries for local and main I had overlooked the iterator
for /proc/net/route. As a result it was outputting both local and main
when the two tries were merged.
This patch resolves that by only providing output for aliases that are
actually in the main trie. As a result we should go back to the original
behavior which I assume will be necessary to maintain legacy support.
Fixes: 0ddcf43d5 ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the restart handling hack from the r8a7740 generic multiplatform
case.
Restart on DT-based r8a7740 platforms is now handled through the
R-Mobile reset driver.
This reverts commit 1174c712af ("ARM: shmobile: r8a7740: Add
restart callback").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit e042681894 ("ARM: shmobile: r8a7790: Remove legacy
code"), all R-Car Gen2 SoCs are supported by multiplatform kernels only.
As CONFIG_COMMON_CLK is always set for multiplatform kernels, we can
remove related #ifdefs in code specific to R-Car Gen2 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the stray closing parenthesis in the config description for the
DEBUG_RCAR_GEN2_SCIF0 option.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some drivers compare struct clk pointers as a means of knowing
if the two pointers reference the same clock hardware. This behavior is
dubious (drivers must not dereference struct clk), but did not cause any
regressions until the per-user struct clk patch was merged. Now the test
for matching clk's will always fail with per-user struct clk's.
clk_is_match is introduced to fix the regression and prevent drivers
from comparing the pointers manually.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[arnd@arndb.de: Fix COMMON_CLK=N && HAS_CLK=Y config]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[sboyd@codeaurora.org: const arguments to clk_is_match() and
remove unnecessary ternary operation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As the only comments I got for the "mtd: cfi: reduce stack size"
patch were about whitespace changes, it appears necessary to fix
up the rest of the file as well, which contains the exact same
mistakes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The cfi_staa_write_buffers function uses a large amount of kernel stack
whenever CONFIG_MTD_MAP_BANK_WIDTH_32 is set, and that results in a
warning on ARM allmodconfig builds:
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_write_buffers':
drivers/mtd/chips/cfi_cmdset_0020.c:651:1: warning: the frame size of 1208 bytes is larger than 1024 bytes [-Wframe-larger-than=]
It turns out that this is largely a result of a suboptimal implementation
of map_word_andequal(). Replacing this function with a straightforward
one reduces the stack size in this function by exactly 200 bytes,
shrinks the .text segment for this file from 27648 bytes to 26608 bytes,
and makes the warning go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We're not initializing the ooblen field. Our users don't care, since
they check that oobbuf == NULL first, but it's good practice to zero
unused fields out.
We can drop the NULL initializations since we're memset()ing the whole
thing.
Noticed by Coverity, CID #200821, #200822
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The only exit (break) from the preceding loop is nested within a
condition which yields req == NULL. This code is dead.
Coverity CID #752669
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Coverity noticed that these 'ret' assignments weren't being used. Let's
use them.
Note that nand_lock() and nand_unlock() are still not officially used by
any drivers.
Coverity CIDs #1227054 and #1227037
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
'ret' is always zero, so this is all dead code.
This should quiet Coverity CID #1226739.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
If no devices were found, we would already have skipped over this code.
Detected by Coverity, CID #744270
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PARAM command was long unimplemented and it probably wasn't
noticed because chip probing using only the few bytes returned by the
READID command are good enough in most cases to determine the chip in
use.
Still to notice such a shortcoming earlier in the future would be nice
in case it's something more vital.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand driver never supported the PARAM command to read out the
ONFI parameter page and so always relied on probing my manufacturer and
device id (as provided by the READID command).
This patch implements reading out the first parameter page copy at least
which should be good enough in practise.
This makes the boot log change from
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron NAND 128MiB 1,8V 16-bit
to
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron MT29F1G16ABBDAH4
on my machine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand controller works pagewise and so usually only sends
commands to the flash chip with column == 0. A request with column != 0
from the upper layer is then fulfilled by indexing appropriately into the
device's RAM buffer.
To be able to access the ONFI marker at offset 0x20 in reply to the
READID command however it's invalid to read 32 bytes starting from
column 0.
So let the function used to send the address cycles send the column
address actually passed instead of 0 and fix all callers to pass 0
instead appropriately. Also add some warnings in case this patch changes
the drivers semantics.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the hardware operates in 16 bit mode it always reads 16 bits even
for operations that only have the lower 8 bits defined. So the upper
bits must be discarded. Do this in the read_byte callback instead of
when reading the NAND id to support reading byte wise more than 5 bytes
and at other occations (like reading the ONFI parameter page).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.
Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Add support for a new SoC: Armada 39x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9RvwACgkQCwYYjhRyO9UGwQCfXlE0v/h5zAG6j/LTAFuMLP3w
ZqoAmwZErUyIkfr00w9KyOgLxnYefTJ6
=q2zn
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.1' of git://git.infradead.org/linux-mvebu into next/soc
Pull "mvebu soc changes for v4.1 (part #1)" from Gregory CLEMENT:
- Add support for a new SoC: Armada 39x
* tag 'mvebu-soc-4.1' of git://git.infradead.org/linux-mvebu:
Documentation: arm: update supported Marvell EBU processors
ARM: mvebu: add core support for Armada 39x
devicetree: bindings: add new SMP enable method for Marvell Armada 39x
devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family
- add the new Armada 39x SoC in mvebu_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9R2MACgkQCwYYjhRyO9UOLQCfeQuNL/nHDlc+0GanS9pBAyil
sBMAoKGEjhdA1NTfnykWexg3Ml4BwVX4
=VaQQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig-4.1' of git://git.infradead.org/linux-mvebu into next/defconfig
Pull "mvebu defconfig changes for v4.1 (part #1)" from Gregory CLEMENT:
- add the new Armada 39x SoC in mvebu_v7_defconfig
* tag 'mvebu-defconfig-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: enable Armada 39x in mvebu_v7_defconfig
- Constify the dt_compat table in DT_MACHINE_START
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9Re4ACgkQCwYYjhRyO9WLaQCfeTz2auqoPt5vXTJjs9/sXLEL
dQIAnjPIpZfLVBnNo1BzK96RUYHEJ20+
=QIYe
-----END PGP SIGNATURE-----
Merge tag 'mvebu-cleanup-4.1' of git://git.infradead.org/linux-mvebu into next/cleanup
Pull "mvebu clean-up changes for v4.1 (part #1)" from Gregory CLEMENT:
- Constify the dt_compat table in DT_MACHINE_START
* tag 'mvebu-cleanup-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add __initconst specifiers on DT_MACHINE_START dt_compat tables
Adds support for Spreadtrum's SoC Platform in the arm64 Kconfig and
defconfig files.
Signed-off-by: Zhizhou Zhang <zhizhou.zhang@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Adds the device tree support for Spreadtrum SC9836 SoC which is based on
Sharkl64 platform.
Sharkl64 platform contains the common nodes of Spreadtrum's arm64-based SoCs.
Signed-off-by: Zhizhou Zhang <zhizhou.zhang@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Initial version of device tree for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Florian Fainelli says:
====================
net: dsa: support PHY reads/writes diversion
This patch series completes the PHY reads/writes diversion when we need to use
the slave MII bus provided by DSA and the underlying switch drivers to
implement the real PHY reads and writes. This is particularly useful when they
are conflicting MDIO bus addresses as in the case of multiple Broadcom switches
connected to each other (internal and external, or just external).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.
Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for dealing with indirect reads and writes towards
certain PHY devices, move the code which deals with binding the PHY
device to the slave MII bus created by DSA to its own function:
dsa_slave_phy_connect().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export of_mdio_parse_addr() which allows parsing a given Ethernet PHY
node MDIO address, verify it is within the allowed range, and return
its value. This is going to be useful for the DSA code which needs to
deal with multiple layers of MDIO buses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9S+0ACgkQCwYYjhRyO9XSkQCfcrsiF6bS+B1B9Gdu+nBwyXdC
BHYAmwUm92D7yH8ePjbKldM4ONM1315b
=yn/6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
The watchdog clock should be disable in dw_wdt_suspend, but we set a
dummy clock to watchdog for rk3288. So the watchdog will continue to
work during suspend. And we switch the system clock to 32khz from 24Mhz,
during suspend, so the watchdog timer over count will increase to
755 times, about 12.5 hours, the original value is 60 seconds. So
watchdog will reset the system over a night, but voltage are all
incorrect, then it hang on reset.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The register-default delay time for wait the 24MHz OSC stabilization as well
as PMU stabilization is 750ms, let's decrease them to a still safe 30ms.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Make function rockchip_get_core_reset() static because it is not used
outside of the platsmp.c file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 0-day kernel test infrastructure reported a use of uninitialized
variable warning for local_table due to the fact that the local and main
allocations had been swapped from the original setup. This change corrects
that by making it so that we free the main table if the local table
allocation fails.
Fixes: 0ddcf43d5 ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want tile 0,0 to artificially constrain the size of the legacy
fbdev device. Instead when reducing fb_size to be the minimum of all
displays, only consider the rightmost and bottommost tiles.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Hai Li <hali@codeaurora.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>