This patch removes custom printk macro ERR.
All the calls to this macro were replaced by de_err and pr_err.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the use of custom printk macros ERR and replace it
with dev_err, or pr_err in the following cases:
- if no appropriate struct device *dev field where found for dev_err.
- or dev could be null eg. "dev_err(udc->dev" not possible inside "if
(udc == null)"
Issue addressed by checkpatch.pl.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the test statement for an argument to _nbu2ss_pullup
function, for it can't be null due to previous derefrences.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warnings:"do not add new
typedefs" and "Use of volatile is usually wrong".
Remove typedefs keyword and rename identifiers appropriately.
Remove volatile from union usb_regs_access
Update related files.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of yet another duplicated copy of the RF type
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No point shifting raid right, just to shift it left again before
re-adding it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only case where fw_ractrl = false was when the firmware failed to
load, and in that case we are dead in the water anyway.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HNIc
-----END PGP SIGNATURE-----
Merge tag 'for-v4.0-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes
ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
[bhelgaas: changelog]
Fixes: 6675ef212d ("PCI: spear: Fix Section mismatch compilation warning for probe()")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CC: stable@vger.kernel.org # v3.17+
Commit bca9690b94 ("clk: divider: Make generic for usage elsewhere")
returned only the divider value for read-only dividers instead of the
actual rate.
Fixes: bca9690b94 ("clk: divider: Make generic for usage elsewhere")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can simplify the code by returning patch_build_controls() directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch to add an VT1613 AC97 codec support.
This codec has additional DC offset removal control,
headphone output and no video input.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU96stAAoJECTWi3JdVIfQLfUH/jBYQqxrPp8qm7Lt9LOuwC4U
SOi0ERIVhLSKZMo7G4wHmbEapx2FBgH+wxqh9kNLaISvOIH4odFS4Fr1XYE70cY9
97M46uzLqdaKCDgvkXdx1NLA0zubEGWLOtdVYlrMAzin0FXNH+KYhxkRQbJ6f0LE
yKmNemnHHtJ4gDl/kMED7bc+mkYSOpwUE/8HLOEA8bcE3luDnj7rvQwOhPIYq0Tz
Ij4GM8HSfWPp/k3YmZVcF8GA6icN3LG5Jg7DOu6S19fMYimTDaHQDCw0AoLfiIOQ
DykyHg7ay/I3B6zUz4JikLIW5KjFxZfeQ818YE0GQ4PgePfb0GSIFt0LnNmq4Oo=
=GIb7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
MediaTek SoC expect to work with a pinctrl driver.
Select PINCTRL if ARCH_MEDIATEK is selected.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We finally have all the pieces in place, so let's include the
vector facility bit in the mask of available hardware facilities
for the guest to recognize. Also, enable the vector functionality
in the guest control blocks, to avoid a possible vector data
exception that would otherwise occur when a vector instruction
is issued by the guest operating system.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>