The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the attach of this driver a couple commands are sent to the hardware
with usb_bulk_msg() to read the firmware version information. This information
is then dumped as dev_info() kernel messages. Thee messages are just added
noise and don't effect the operation of the driver.
For simplicity, remove the messages as well as the then unused functions
vmk80xx_read_eeprom() and vmk80xx_check_data_link().
This also fixes an issue reported by coverity about an out-of-bounds write
in vmk80xx_read_eeprom().
Reported-by: coverity (CID 711413)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "stalled" variable this function is used to detect if the DMA operation
is stalled while trying to disable DMA on a full comedi sample. The reset
of this variable should only occur when the remaining bytes of the DMA
transfer does not equal the remaining bytes from the last check.
Reported-by: coverity (CID 1271132)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are fixes for patches in the recent merge window and are in a separate
branch to avoid rebasing the main fixes-togreg branch.
* jsa1212 - select missing REGMAP_I2C
* ssp_common - build warning fix for PM functions when PM not in use.
* ak8975 - the addition of a utility library for this driver (as part of
adding new device support) led to a dependency not being inforced
for the original driver (I2C and GPIOLIB).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KRES
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.0b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 4.0 cycle (or round one part two really!)
These are fixes for patches in the recent merge window and are in a separate
branch to avoid rebasing the main fixes-togreg branch.
* jsa1212 - select missing REGMAP_I2C
* ssp_common - build warning fix for PM functions when PM not in use.
* ak8975 - the addition of a utility library for this driver (as part of
adding new device support) led to a dependency not being inforced
for the original driver (I2C and GPIOLIB).
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJU8aP7AAoJEFSFNJnE9BaIr7oQAKUtw6ScwBnCGDV+3ttEvUAl
8oSNVNKoWdBiuQK5XZHJVVVm7/n7Okt6rT8X+LjY5JsVP6lZRItAtOkwNibyyS5Q
MZk3on8E7qEaASTOPPb+Izb+d2azevUaZptqTlQSaFJgs8HuBm89DwJ9H6SKZKAy
kqZdjiDLx95XNAMSKiM7531Dv+TKU0BGPP8Zc0vIviUQbAcFQ6hHtfaFwU2m/hlx
Cyn4UB3i2jbZmuvfL5zwHZBIjTpczlLuihQFpNAMq73pwROgbwVuQ6azBz5ib0dE
gHE5AG/c/uLXO0IFvPlUmkLqQyPoTJ8dsgrjozOi+GPqWGfaBf1Iet0zfqVcJWjE
jCpJqlNfcukvBnAsSMwQM/mHGVdGXd07alKjCoZsQkm0aG/DQxLn2QRWVAUno8eL
zbuDCpk3rH8c5U9Ytb0likBRurM8UyTTkUhCJOpdS1iyNRe+pK8Krp/STMhc3a96
YWQxpO3p127yyc8EXdEl5N5kJwtWaV0W09vGV4oSk8A9fF7MTR2fe31pw7Si+sb3
gTsRMC1bPqF2f8UMcjxqd72IKz5GKvaIOh+J6hdN0UaITsQr+dWbPj1oAkgRQgdJ
EC57hqVLJTl3S1AYtev98+LgemOARbsBYbc/FVlhTpaZPhxXOLyMsvaQ93Fa7jFr
HXPJZailkvt7TgLiuoW6
=iNyv
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 4.0 cycle. Note a followup
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
ak8975 depends on I2C and GPIOLIB, so any symbols that selects
ak8975 must have the same dependency, or we get build errors:
drivers/iio/magnetometer/ak8975.c: In function 'ak8975_who_i_am':
drivers/iio/magnetometer/ak8975.c:393:2: error: implicit declaration of function 'i2c_smbus_read_i2c_block_data' [-Werror=implicit-function-declaration]
ret = i2c_smbus_read_i2c_block_data(client, AK09912_REG_WIA1,
^
drivers/iio/magnetometer/ak8975.c: In function 'ak8975_set_mode':
drivers/iio/magnetometer/ak8975.c:431:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration]
ret = i2c_smbus_write_byte_data(data->client,
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57e73a423b ("iio: ak8975: add ak09911 and ak09912 support")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All possible code-paths will assign ret to suitable values so this
default value is not needed.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A failure of sahara_hw_descriptor_create() with -EINVAL due to scatter list
out of bounds/invalid would not be reported back. This patch just passes on
the -EINVAL so it is visible in sahara_queue_manage().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
return type of wait_for_completion_timeout is unsigned long not int, this
patch adds appropriate variables of type unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of ret from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Changed the __driver-gcm-aes-aesni to be a proper aead algorithm.
This required a valid setkey and setauthsize functions to be added and also
some changes to make sure that math context is not corrupted when the alg is
used directly.
Note that the __driver-gcm-aes-aesni should not be used directly by modules
that can use it in interrupt context as we don't have a good fallback mechanism
in this case.
Signed-off-by: Adrian Hoban <adrian.hoban@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch enables VMX module in PPC64.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
OpenSSL implements optimized ASM algorithms which support
VMX instructions on Power 8 CPU.
These scripts generate an endian-agnostic ASM implementation
in order to support both big and little-endian.
- aesp8-ppc.pl: implements suport for AES instructions
implemented by POWER8 processor.
- ghashp8-ppc.pl: implements support for GHASH for Power8.
- ppc-xlate.pl: ppc assembler distiller.
These code has been adopted from OpenSSL project in collaboration
with the original author (Andy Polyakov <appro@openssl.org>).
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds GHASH routines to VMX module in order to
make use of VMX cryptographic acceleration instructions
on Power 8 CPU.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds AES CTR routines to VMX module in order to
make use of VMX cryptographic acceleration instructions
on Power 8 CPU.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds AES CBC routines to VMX module in order to
make use of VMX cryptographic acceleration instructions
on Power 8 CPU.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds AES routines to VMX module in order to
make use of VMX cryptographic acceleration instructions
on Power 8 CPU.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds routines supporting VMX instructions on the
Power 8.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This effectively unexports set_memory_ro() and set_memory_rw()
functions, and thus reverts:
a03352d2c1 ("x86: export set_memory_ro and set_memory_rw").
They have been introduced for debugging purposes in e1000e, but
no module user is in mainline kernel (anymore?) and we
explicitly do not want modules to use these functions, as they
i.e. protect eBPF (interpreted & JIT'ed) images from malicious
modifications or bugs.
Outside of eBPF scope, I believe also other set_memory_*()
functions should be unexported on x86 for modules.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Link: http://lkml.kernel.org/r/a064393a0a5d319eebde5c761cfd743132d4f213.1425040940.git.daniel@iogearbox.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
s3c2410_nand_probe is not the name of the function.
These prints have little utility, so let's just kill them.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
pxa3xx_flash_ids wasn't initialized to 0, which in certain cases could
end up containing corrupted values in its members. Fix this to avoid
possible issues.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As the devicetree binding doesn't require num_cs to exist or be strictly
positive, and neither does the platform data case, a bug appear when
num_cs is set to 0 and panics the kernel.
The issue is that in alloc_nand_resource(), chip is dereferenced without
having a value assigned when num_cs == 0.
Fix this by returning ENODEV is num_cs == 0.
The panic seen is :
Unable to handle kernel NULL pointer dereference at virtual address 000002b8
pgd = c0004000
[000002b8] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
Hardware name: Marvell PXA3xx (Device Tree Support)
task: c3822aa0 ti: c3826000 task.ti: c3826000
PC is at alloc_nand_resource+0x180/0x4a8
LR is at alloc_nand_resource+0xa0/0x4a8
pc : [<c0275b90>] lr : [<c0275ab0>] psr: 68000013
sp : c3827d90 ip : 00000000 fp : 00000000
r10: c3862200 r9 : 0000005e r8 : 00000000
r7 : c3865610 r6 : c3862210 r5 : c3924210 r4 : c3862200
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0000397f Table: 80004018 DAC: 00000035
Process swapper (pid: 1, stack limit = 0xc3826198)
Stack: (0xc3827d90 to 0xc3828000)
...zip...
[<c0275b90>] (alloc_nand_resource) from [<c0275ff8>] (pxa3xx_nand_probe+0x140/0x978)
[<c0275ff8>] (pxa3xx_nand_probe) from [<c0258c40>] (platform_drv_probe+0x48/0xa4)
[<c0258c40>] (platform_drv_probe) from [<c0257650>] (driver_probe_device+0x80/0x21c)
[<c0257650>] (driver_probe_device) from [<c0257878>] (__driver_attach+0x8c/0x90)
[<c0257878>] (__driver_attach) from [<c0255ec4>] (bus_for_each_dev+0x58/0x88)
[<c0255ec4>] (bus_for_each_dev) from [<c0256ec8>] (bus_add_driver+0xd8/0x1d4)
[<c0256ec8>] (bus_add_driver) from [<c0257f14>] (driver_register+0x78/0xf4)
[<c0257f14>] (driver_register) from [<c00088a8>] (do_one_initcall+0x80/0x1e4)
[<c00088a8>] (do_one_initcall) from [<c048ed08>] (kernel_init_freeable+0xec/0x1b4)
[<c048ed08>] (kernel_init_freeable) from [<c0377d8c>] (kernel_init+0x8/0xe4)
[<c0377d8c>] (kernel_init) from [<c00095f8>] (ret_from_fork+0x14/0x3c)
Code: e503b234 e5953008 e1530001 caffffd1 (e59002b8)
---[ end trace a5770060c8441895 ]---
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the handling of the data stage in the driver : don't pump data in
the top-half interrupt, but rather schedule a thread for non dma cases.
This will enable latencies in the data pumping, especially if delays are
required. Moreover platform shall be more reactive as other interrupts
can be served while pumping data.
No throughput degradation was observed, at least on the zylonite
platform, while a slight degradation was being expected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
User visible:
- Fix SIGBUS failures due to misaligned accesses in Sparc64 (David Ahern)
- Fix branch stack mode in 'perf report' (He Kuang)
- Fix a 'perf probe' operator precedence bug (He Kuang)
- Fix Support for different binaries with same name in 'perf diff' (Kan Liang)
- Check kprobes blacklist when adding new events via 'perf probe' (Masami Hiramatsu)
- Add --purge FILE to remove all caches of FILE in 'perf buildid-cache' (Masami Hiramatsu)
- Show usage with some incorrect params (Masami Hiramatsu)
- Add new buildid cache if update target is not cached in 'buildid-cache' (Masami Hiramatsu)
- Allow listing events with 'tracepoint' prefix in 'perf list' (Yunlong Song)
- Sort the output of 'perf list' (Yunlong Song)
- Fix bash completion of 'perf --' (Yunlong Song)
Developer Zone:
- Handle strdup() failure path in 'perf probe' (Arnaldo Carvalho de Melo)
- Fix get_real_path to free allocated memory in error path in 'perf probe' (Masami Hiramatsu)
- Use pr_debug instead of verbose && pr_info perf buildid-cache (Masami Hiramatsu)
- Fix building of 'perf data' with some gcc versions due to incorrect array struct
entry (Yunlong Song)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU8MCoAAoJEBpxZoYYoA71ZOIIANNy2I+ZvipY4WxXf5L6V1TS
fKlL8Kz2XXr7ZcSgTxU4dMFyiXJ/hFsDEpf1hKq2wjaf20UDdhLRY0jszdKrJ0Je
4n2Gt7gJy7odDBsgBI7GPXAceXrD2MKY6njKHjzsDFLJmqVPY3NqVqvt9Dufgfwm
H5lWG35z9Jt/aJbaHeEe49YKBqoacJcqNiCxltE3VW8mIsKA82FUbOHxz03WU7mu
fgjK4EN2oV7sOPAao8ZnkAG9Ib+dyJe5oTI9WkT1ofxM2doaqhX5/vi2t+KOprzC
OB4miIBHody2yuiQZq+y6+BGSVvGqYsZM1sVerA3YQBiK6f4Pf94QxRo8yEJGzI=
=dRR8
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Fix SIGBUS failures due to misaligned accesses in Sparc64 (David Ahern)
- Fix branch stack mode in 'perf report' (He Kuang)
- Fix a 'perf probe' operator precedence bug (He Kuang)
- Fix Support for different binaries with same name in 'perf diff' (Kan Liang)
- Check kprobes blacklist when adding new events via 'perf probe' (Masami Hiramatsu)
- Add --purge FILE to remove all caches of FILE in 'perf buildid-cache' (Masami Hiramatsu)
- Show usage with some incorrect params (Masami Hiramatsu)
- Add new buildid cache if update target is not cached in 'buildid-cache' (Masami Hiramatsu)
- Allow listing events with 'tracepoint' prefix in 'perf list' (Yunlong Song)
- Sort the output of 'perf list' (Yunlong Song)
- Fix bash completion of 'perf --' (Yunlong Song)
Developer Zone:
- Handle strdup() failure path in 'perf probe' (Arnaldo Carvalho de Melo)
- Fix get_real_path to free allocated memory in error path in 'perf probe' (Masami Hiramatsu)
- Use pr_debug instead of verbose && pr_info perf buildid-cache (Masami Hiramatsu)
- Fix building of 'perf data' with some gcc versions due to incorrect array struct
entry (Yunlong Song)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
1e02ce4ccc ("x86: Store a per-cpu shadow copy of CR4")
added a shadow CR4 such that reads and writes that do not
modify the CR4 execute much faster than always reading the
register itself.
The change modified cpu_init() in common.c, so that the
shadow CR4 gets initialized before anything uses it.
Unfortunately, there's two cpu_init()s in common.c. There's
one for 64-bit and one for 32-bit. The commit only added
the shadow init to the 64-bit path, but the 32-bit path
needs the init too.
Link: http://lkml.kernel.org/r/20150227125208.71c36402@gandalf.local.home Fixes: 1e02ce4ccc "x86: Store a per-cpu shadow copy of CR4"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150227145019.2bdd4354@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is possible that _ART/_TRT tables are missing or have errors.
Ignore those failures, as INT3400 thermal zone is still required
for _OSC or mode switch.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Atom* Processor C2000 Product
Family for Microservers (Avoton). Avoton - SoCs for micro-servers
has package C-states which can be used for idle injection.
Reported-by: Jose Navarro <jose.navarro@intel.com>
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jos.c.venegas.munoz@intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
gcc complains about the 'cols' variable being unused. This is
unavoidable, given the ncurses getmaxyx() macro-based API, which wants
to assign to a variable directly, even when we're not going to use it.
Warning:
gcc -O1 -Wall -Wshadow -W -Wformat -Wimplicit-function-declaration -Wimplicit-int -fstack-protector -D VERSION=\"1.0\" -c -o tui.o tui.c
tui.c: In function ‘show_dialogue’:
tui.c:288:12: warning: variable ‘cols’ set but not used [-Wunused-but-set-variable]
int rows, cols;
^
So, add a hack to get rid of that warning.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Some distros (e.g., Arch Linux) don't package the tinfo library
separately from ncurses, so don't unconditionally include it. Instead,
use pkg-config.
The $(STATIC) ugliness is to handle the reported build case from commit
6b533269fb ("tools/thermal: tmon: fix compilation errors when building
statically"), where a developer wants to be able to build with:
make LDFLAGS=-static
which requires an additional pkg-config flag.
Finally, support a lowest common denominator fallback (-lpanel
-lncurses) for build systems that don't have pkg-config entries for
ncurses.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We might want to prepare CFLAGS outside of this Makefile, so don't
overwrite its initial value.
Then, support $(CROSS_COMPILE), so we can use a cross-compile toolchain.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The number of rows in the dialog vary according to the number of cooling
devices. However, some of the windowing computations were assuming a
fixed number of rows. This computation is OK when we have between 4 and
9 cooling devices (and they wrap to the next column), but with fewer
devices, we end up printing off the end of the window.
This unifies the row computation into a single function and uses that
throughout the TUI code. This also accounts for increasing the number of
rows when there are more than 9 total cooling devices.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We can use the ncurses API to get the number of rows.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If we launch in daemon mode (--daemon), we don't have the ncurses UI,
but we might want to set the target temperature still. For example,
someone might stick the following in their boot script:
tmon --control intel_powerclamp --target-temp 90 --log --daemon
This would turn on CPU idle injection when we're around 90 degrees
celsius, and would log temperature and throttling info to
/var/tmp/tmon.log.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When the sysctl table is constified, we won't be able to directly modify
it. Instead, use a table copy that carries any needed changes.
Suggested-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: Kees Cook <keescook@chromium.org>
The arm-soc bug fixes this time around are mostly for the omap
platform, coming from a pull request from Tony Lindgren and are
almost entirely fixing dts files.
The other two changes enable support for the shmobile platform
in generic armv7 kernels and change some properties in the
ARM64 reference board dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tYZw
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"The arm-soc bug fixes this time around are mostly for the omap
platform, coming from a pull request from Tony Lindgren and are almost
entirely fixing dts files.
The other two changes enable support for the shmobile platform in
generic armv7 kernels and change some properties in the ARM64
reference board dts files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable shmobile platforms
arm64: Add L2 cache topology to ARM Ltd boards/models
ARM: dts: am335x-bone*: usb0 is hardwired for peripheral
ARM: dts: dra7x-evm: beagle-x15: Fix USB Host
ARM: omap2plus_defconfig: Fix SATA boot
ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver
ARM: dts: dra7: Correct the dma controller's property names
ARM: dts: omap5: Correct the dma controller's property names
ARM: dts: omap4: Correct the dma controller's property names
ARM: dts: omap3: Correct the dma controller's property names
ARM: dts: omap2: Correct the dma controller's property names
ARM: dts: am437x-idk: fix sleep pinctrl state
ARM: omap2plus_defconfig: enable TPS62362 regulator
ARM: dts: am437x-idk: fix TPS62362 i2c bus
ARM: dts: n900: Fix offset for smc91x ethernet
ARM: dts: n900: fix i2c bus numbering
ARM: dts: Fix USB dts configuration for dm816x
ARM: dts: OMAP5: Fix SATA PHY node
ARM: dts: DRA7: Fix SATA PHY node
- ftrace branch generation fix
- branch instruction encoding fix
- include files, guards and unused prototypes clean-up
- minor VDSO ABI fix (clock_getres)
- PSCI functions moved to .S to avoid compilation error with gcc 5
- pte_modify fix to not ignore the mapping type
- crypto: AES interleaved increased to 4x (for performance reasons)
- text patching fix for modules
- swiotlb increased back to 64MB
- copy_siginfo_to_user32() fix for big endian
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IGAn
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"Various arm64 fixes:
- ftrace branch generation fix
- branch instruction encoding fix
- include files, guards and unused prototypes clean-up
- minor VDSO ABI fix (clock_getres)
- PSCI functions moved to .S to avoid compilation error with gcc 5
- pte_modify fix to not ignore the mapping type
- crypto: AES interleaved increased to 4x (for performance reasons)
- text patching fix for modules
- swiotlb increased back to 64MB
- copy_siginfo_to_user32() fix for big endian"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpuidle: add asm/proc-fns.h inclusion
arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian
arm64: Increase the swiotlb buffer size 64MB
arm64: Fix text patching logic when using fixmap
arm64: crypto: increase AES interleave to 4x
arm64: enable PTE type bit in the mask for pte_modify
arm64: mm: remove unused functions and variable protoypes
arm64: psci: move psci firmware calls out of line
arm64: vdso: minor ABI fix for clock_getres
arm64: guard asm/assembler.h against multiple inclusions
arm64: insn: fix compare-and-branch encodings
arm64: ftrace: fix ftrace_modify_graph_caller for branch replace
In Linux 4.0-rc1 ARM Versatile PCI build fails to build due to what
appears to be an API update. This patch is a very simple correction,
merely posted as a heads-up to the maintainers. Hopefully a better
fix can be forwarded to Linus.
[ arnd: the patch actually looks correct, so let's take this version ]
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Erik Hugne says:
====================
tipc: bug fix and some improvements
Most important is a fix for a nullptr exception that would occur when
name table subscriptions fail. The remaining patches are performance
improvements and cosmetic changes.
v2: remove unnecessary whitespace in patch #2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bearer is disabled by manual intervention, all links over that
bearer should be purged, indicated with the 'shutting_down' flag.
Otherwise tipc will get confused if a new bearer is enabled using
a different media type.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>