Hugetlbfs pages will get a refcount in get_any_page() or
madvise_hwpoison() if soft offlining through madvise. The refcount which
is held by the soft offline path should be released if we fail to isolate
hugetlbfs pages.
Fix it by reducing the refcount for both isolation success and failure.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After trying to drain pages from pagevec/pageset, we try to get reference
count of the page again, however, the reference count of the page is not
reduced if the page is still not on LRU list.
Fix it by adding the put_page() to drop the page reference which is from
__get_any_page().
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VMX encodes access rights differently from LAR, and the latter is
most likely what x86 people think of when they think of "access
rights".
Rename them to avoid confusion.
Cc: kvm@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The two commits noted below added calls to ip_hdr() and ipv6_hdr(). They
need a correctly set skb network header.
Unfortunately we cannot rely on the device drivers to set it for us.
Therefore setting it in the beginning of the according ndo_start_xmit
handler.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Fixes: ab49886e3d ("batman-adv: Add IPv4 link-local/IPv6-ll-all-nodes multicast support")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When an interface is purged, the broadcast packets scheduled for this
interface should get purged as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The list_del() calls were changed to list_del_init() to prevent
an accidental double deletion in batadv_tt_req_node_new().
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756c ("batman-adv: Announce new capability via multicast TVLV")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756c ("batman-adv: Announce new capability via multicast TVLV")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: e17931d1a6 ("batman-adv: introduce capability initialization bitfield")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 3f4841ffb3 ("batman-adv: tvlv - add network coding container")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 17cf0ea455 ("batman-adv: tvlv - add distributed arp table container")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The PCM DAIs need to be loaded and added to ASoC core ealier than the
graph (route). Otherwise, adding routes will fail for missing DAIs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[djbw: tools/testing/nvdimm/ and memunmap_pmem support]
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG4573 is used on the LG LCD LB043WV2-SD01, an industrial 4.3" TFT
panel with SPI control interface.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds vendor prefix for Okaya Electronic America, a provider
of LCD modules and display technologies.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[treding@nvidia.com: add .bpc field for panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The bus format both specifies the bpc and the way the individual bits get
serialized into the 7 LVDS timeslots.
While the is only one standard mapping for 6 bpc and so the driver could
infer the bit mapping from the bpc alone, there are more options for the
8 bpc case which makes specifiying the bus format mandatory.
To keep things consistent across panels and to set a precedent for new
panel additions add the proper bus format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SPI Davinci driver has been updated to allow SOCs to specify their minimum
prescale value. Update the various SOCs board files that use this driver with
their proper prescaler limit.
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Failure to create a debugfs node is not an error, but we print a
warning upon failure to create the node. Downgrade this to a
debug printk so that we're quiet here. This allows multiple
drivers to request a CPU's regulator so that CPUfreq and AVSish
drivers can coexist.
The downside of this approach is that whoever gets to debugfs first
the others who come later to not have any debugfs attributes associated
with them.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust set DAI format function in fsl_ssi driver
so it doesn't fail and clears RXDIR in AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instantiate AC'97 CODEC in fsl_ssi driver AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether setting AC'97 ops succeeded and clean them
on removal so the fsl_ssi driver can be reloaded.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 bus can support asymmetric playback/capture rates
so enable them in this case in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 DAI driver struct need the same probe method as
I2S one to setup DMA params in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
IPG clock have to be enabled during AC'97 CODEC register
access in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current "We only connect the NOR to this controller now." text
is not very clear, so explain it better by saying that generic SPI
is not supported by SPI_FSL_QUADSPI and only SPI NOR is.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add SPI-NOR driver for the SPI Flash Interface (SPIFI)
controller that is found on newer NXP MCU devices.
The controller supports serial SPI Flash devices with 1-, 2-
and 4-bit width in either SPI mode 0 or 3. The controller
can operate in either command or memory mode. In memory mode
the Flash is exposed as normal memory and can be directly
accessed by the CPU.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add device tree binding documentation for the SPI Flash Interface
(SPIFI) found on NXP LPC18xx and LPC43xx devies.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function is missing a check if map->bus->write is implemented. If
it is not implemented arbitrary raw writes are not possible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull timer fix from Ingo Molnar:
"A single clocksource driver suspend/resume fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/sh_cmt: Only perform clocksource suspend/resume if enabled
regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Pull locking fix from Ingo Molnar:
"A single fix for a locking self-test crash"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix kernel panic in locking-selftest
When a BTT is instantiated on a namespace it must validate the namespace
uuid matches the 'parent_uuid' stored in the btt superblock. This
property enforces that changing the namespace UUID invalidates all
former BTT instances on that storage. For "IO namespaces" that don't
have a label or UUID, the parent_uuid is set to zero, and this
validation is skipped. For such cases, old BTTs have to be invalidated
by forcing the namespace to raw mode, and overwriting the BTT info
blocks.
Based on a patch by Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use arena_is_valid as a common routine for checking the validity of an
info block from both discover_arenas, and nd_btt_probe.
As a result, don't check for validity of the BTT's UUID, and lbasize.
The checksum in the BTT info block guarantees self-consistency, and when
we're called from nd_btt_probe, we don't have a valid uuid or lbasize
available to check against.
Also cleanup to return a bool instead of an int.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate the parameters passed to arena_is_valid into just nd_btt,
and an info block to increase re-usability.
Similarly, btt_arena_write_layout doesn't need to be passed a uuid, as
it can be obtained from arena->nd_btt.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
