When reading the interrupt status after a FW reset handshake
timeout, read the actual value not the mask for the non-MSIX
case.
Fixes: ab606dea80 ("wifi: iwlwifi: pcie: add support for the reset handshake in MSI")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.83aafead6061.I2f8571aafa55aa3b936a30b938de9d260592a584@changeid
There is a requirement to exit EMLSR if there wasn't enough throughput
in the secondary link.
This is checked in check_tpt_wk, which runs every 5 seconds in a high
throughput scenario (when the throughput blocker isn't set)
It can happen that this worker is running immediately after we entered
EMLSR, and in that case the secondary link didn't have a chance to have
throughput. In that case we will exit EMLSR for no good reason.
Fix this by tracking the time we entered EMLSR, and in the worker make
sure that 5 seconds passed from when we entered EMLSR. If not, don't
check the secondary link throughput.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.c680f8d7dc37.I8a02d1e8d99df3789da8d5714f19b31a865a61ff@changeid
Move the iwl_trans_pcie_dump_regs() function to utils.c in the PCIe
directory since it operates on PCIe registers and is not
hardware-dependent.
Refactor the pcie_dbg_dumped_once indicator, previously part of the
iwl_trans_pcie struct, into a static variable within the
iwl_trans_pcie_dump_regs() function, where it is used.
Signed-off-by: Rotem Kerem <rotem.kerem@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.06950459ce97.I3105158eb9ae698efebe4b9ada1093aeb1f1b869@changeid
The iwlmld driver is able to handle TTLM changes as long as all TIDs
have the same TID to Link Mapping. Add the corresponding code so that
mac80211 will accept and trigger the TTLM change.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.3b0a4fd2c12b.I1fab7840f1cc222bd1e8cb58ac1a4177474fcd56@changeid
Temporarily block EMLSR when scanning on a P2P Device interface,
as this is an indication that P2P activity is about to start, e.g.,
P2P client connection to a P2P GO.
Since a P2P scan while a station interface connection is active might
be long, increase the EMLSR blocking timeout to 10 seconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.85fb79d537fe.I27523f8d3f00f2b66f5f555f098e323be29465ea@changeid
For the iwlmld driver the RX command is using struct iwl_rx_mpdu_desc
and not the much older struct iwl_rx_mpdu_res_start. Adjust the value of
rx_mpdu_cmd_hdr_size accordingly so that the trace data is correct.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.688d95d99ff3.Id3055ca6c19cf8c821cbbd80c09ca2a21d9acec7@changeid
Since secs_to_jiffies()(commit:b35108a51cf7) has been introduced, we can
use it to avoid scaling the time to msec.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Link: https://patch.msgid.link/20250612022501.3492345-1-liyuesong@vivo.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Doing a scan right after link activation can be less reliable
than at other times, as the firmware is still busy trying to
catch beacons from the just activated link, etc. In case a new
MLO scan request comes in, defer it for a few seconds after a
link activation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.09548e958a9e.I24dbfd425da260f3ae6fa5a48fe25bd4ab6fcf99@changeid
The (applicable) firmware versions will send an error interrupt as
part of the resume process, so there's no need now to check for it
explicitly. Simplify the code. This also fixes an issue where any
dump taken during the resume isn't able to do the reset handshake
as part of the dump (since interrupts are disabled) and then there
isn't all the correct data and we get more errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9e778f1bae0c.I96483b5236ab23141b45079464c73f93e0164e65@changeid
Add a debugfs file to be able to control how long, at most,
the device will sleep before waking up the host. This will
be useful to test certain "assert during suspend" scenarios
for the previous change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9f2a39cae1e1.Ie0003f21286fea50b507d0debe06332b030cd4cb@changeid
The D3 handshake can be interrupted by an error, especially
on resume where we no longer want to check explicitly for
errors. Expand the sx_complete to sx_state and handle any
errors occurring during the handshake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.157dca92c573.I6dd3b9d2f435c2c363224aa84e373931e56a545f@changeid
At load time, the firmware may request a TOP reset via
bit 6 in the IPC status register. Handle that and set
TOP reset in that case. Since the init will be retried,
there's no need to do anything else.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.0875d5f7e066.I62f14008d89416bc4a3a1056e06762561a7fac57@changeid
From Patrisious:
This short series from Patrisious extends mlx5 flow steering logic to
allow creation rule creation with priorities in RDMA TRANSPORT tables.
Thanks
Link: https://lore.kernel.org/all/cover.1750148083.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
* mlx5-next: (200 commits)
net/mlx5: fs, add multiple prios to RDMA TRANSPORT steering domain
Linux 6.16-rc2
...
RDMA TRANSPORT domains were initially limited to a single priority.
This change allows the domains to have multiple priorities, making
it possible to add several rules and control the order in which
they're evaluated.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/b299cbb4c8678a33da6e6b6988b5bf6145c54b88.1750148083.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
There's no corresponding platform_get_drvdata() used in this module or
the higher-level gpio-mmio. Let's remove the unneeded call to
platform_set_drvdata().
Link: https://lore.kernel.org/r/20250618074653.25555-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Currently in ib_free_cq, it disables IRQ or cancel the CQ work before
driver destroy_cq. This isn't good as a new IRQ or a CQ work can be
submitted immediately after disabling IRQ or canceling CQ work, which
may run concurrently with destroy_cq and cause crashes.
The right flow should be:
1. Driver disables CQ to make sure no new CQ event will be submitted;
2. Disables IRQ or Cancels CQ work in core layer, to make sure no CQ
polling work is running;
3. Free all resources to destroy the CQ.
This patch adds 2 driver APIs:
- pre_destroy_cq(): Disable a CQ to prevent it from generating any new
work completions, but not free any kernel resources;
- post_destroy_cq(): Free all kernel resources.
In ib_free_cq, the IRQ is disabled or CQ work is canceled after
pre_destroy_cq, and before post_destroy_cq.
Fixes: 14d3a3b249 ("IB: add a proper completion queue abstraction")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://patch.msgid.link/b5f7ae3d75f44a3e15ff3f4eb2bbdea13e06b97f.1750062328.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Always enable vport loopback for both MPV devices on driver start.
Previously in some cases related to MPV RoCE, packets weren't correctly
executing loopback check at vport in FW, since it was disabled.
Due to complexity of identifying such cases for MPV always enable vport
loopback for both GVMIs when binding the slave to the master port.
Fixes: 0042f9e458 ("RDMA/mlx5: Enable vport loopback when user context or QP mandate")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/d4298f5ebb2197459e9e7221c51ecd6a34699847.1750064969.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In case, CC counters are querying for the second port use the correct
core device for the query instead of always using the master core device.
Fixes: aac4492ef2 ("IB/mlx5: Update counter implementation for dual port RoCE")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/9cace74dcf106116118bebfa9146d40d4166c6b0.1750064969.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>