In debugging a recent problem with an xfstest, noticed that we weren't
tracing cases where the ioctl was not supported. Add dynamic tracepoint:
"trace-cmd record -e smb3_unsupported_ioctl"
and then after running an app which calls unsupported ioctl,
"trace-cmd show"would display e.g.
xfs_io-7289 [012] ..... 1205.137765: smb3_unsupported_ioctl: xid=19 fid=0x4535bb84 ioctl cmd=0x801c581f
Acked-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The problem is that the MDIO controller can't detect any of the PHYs.
The reason is that the lan966x is not pulling high the GPIO 53 that is
connected to the PHYs reset GPIO. Without doing this the PHYs are kept
in reset. The mdio controller framework has the possibility to control a
GPIO to release the reset of the PHYs. So take advantage of this and set
line to be high before accessing the PHYs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20251119134750.394655-1-horatiu.vultur@microchip.com
[claudiu.beznea: add microchip in patch title, s/possiblity/possibility
in patch description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Fix lcdif compatible according to bindings doc.
dtbs_check tested only, a glance at the datasheet shows that it should be
the correct fallback compatible.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kobo Clara 2e revision b requires the JD9930/FP9931 regulator driver
for the EPD, so enable it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now there is a driver and binding for the JD9930, so add the information
to the devicetree for revision b.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix lcdif compatible according to bindings doc.
dtbs_check tested only, a glance at the datasheet shows that it should be
the correct fallback compatible.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add binding documentation for the Apalis iMX8QP SoM mated with Apalis
Ixora and Apalis Evaluation board.
Apalis iMX8QP is a variant of the Apalis iMX8QM, using an NXP i.MX8QP
SoC instead of the i.MX8QM. The two SoCs are pin to pin compatible, with
the i.MX8QP being a lower end variant, with a slower GPU and one Cortex
A72 core instead of two.
The two Apalis SoMs variants share the same schematics and PCB, and the
iMX8QP variant exists only on revision V1.1 of board.
Link: https://www.nxp.com/products/i.MX8
Link: https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Apalis iMX8QP SoM mated with Apalis Ixora and Apalis
Evaluation board.
Apalis iMX8QP is a variant of the Apalis iMX8QM, using an NXP i.MX8QP
SoC instead of the i.MX8QM. The two SoCs are pin to pin compatible, with
the i.MX8QP being a lower end variant, with a slower GPU and one Cortex
A72 core instead of two.
The two Apalis SoMs variants share the same schematics and PCB, and the
iMX8QP variant exists only on revision V1.1 of board.
Link: https://www.nxp.com/products/i.MX8
Link: https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for NXP i.MX8QP SoC, this is pin to pin compatible variant
of the i.MX8QM, with a slower GPU and one Cortex A72 core instead of
two.
Link: https://www.nxp.com/products/i.MX8
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add labels to the cpu cluster nodes to prepare for the addition of the
i.MX8QP SoC in which these nodes would need to be adjusted from another
DT file.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects lowercase hex for values and unit
addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects exactly one space around '=' and
before '{' characters.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DTS coding style prefers hyphens instead of underscores in the node
names. Change should be safe, because node names are not considered an
ABI.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mt35xu512aba spi nor support on imx943-evk board.
This nor chip support OCT DTR mode.
For the reset pin, since the nor chip side need 1.8v IO
voltage for reset pin, but the IO expander side use 3.3v
IO voltage, so to make circuit safe, need to config the
pad as OPEN DRAIN.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX952 is designed for AI-powered sensor fusion and vision sensing
applications, it features 4 Corte-A55, 1 Cortex-M33, 1 Cortex-M7 and
NXP eIQ NPU and advanced graphics, video and advanced security with
edgelock. Product info could be found at:
https://www.nxp.com/products/i.MX-952
The basic device tree includes:
- clock, pin, power header files
- device nodes: CPU[0-3], SCMI firmware, Interrupt Controller, Sys counter,
eDMA, MU, SPI, UART, I2C, USB and etc
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dma_alloc_coherent() allocates a dma-mapped buffer, pbl->pg_arr[i].
The dma_free_coherent() should pass the same buffer to
dma_free_coherent() and not page-aligned.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20251230085121.8023-2-fourier.thomas@gmail.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
On PREEMPT_RT kernels, after rt6_get_pcpu_route() returns NULL, the
current task can be preempted. Another task running on the same CPU
may then execute rt6_make_pcpu_route() and successfully install a
pcpu_rt entry. When the first task resumes execution, its cmpxchg()
in rt6_make_pcpu_route() will fail because rt6i_pcpu is no longer
NULL, triggering the BUG_ON(prev). It's easy to reproduce it by adding
mdelay() after rt6_get_pcpu_route().
Using preempt_disable/enable is not appropriate here because
ip6_rt_pcpu_alloc() may sleep.
Fix this by handling the cmpxchg() failure gracefully on PREEMPT_RT:
free our allocation and return the existing pcpu_rt installed by
another task. The BUG_ON is replaced by WARN_ON_ONCE for non-PREEMPT_RT
kernels where such races should not occur.
Link: https://syzkaller.appspot.com/bug?extid=9b35e9bc0951140d13e6
Fixes: d2d6422f8b ("x86: Allow to enable PREEMPT_RT.")
Reported-by: syzbot+9b35e9bc0951140d13e6@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6918cd88.050a0220.1c914e.0045.GAE@google.com/T/
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20251223051413.124687-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add TDP data for laptop model G835LW.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Link: https://patch.msgid.link/20251229204458.2658777-1-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
If device max_mr_size bits in the range [mr_page_shift+31:mr_page_shift]
are zero, the `min3` function will set clt_path::max_pages_per_mr to
zero.
`alloc_path_reqs` will pass zero, which is invalid, as the third parameter
to `ib_alloc_mr`.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Signed-off-by: Honggang LI <honggangli@163.com>
Link: https://patch.msgid.link/20251229025617.13241-1-honggangli@163.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
rose_kill_by_device() collects sockets into a local array[] and then
iterates over them to disconnect sockets bound to a device being brought
down.
The loop mistakenly indexes array[cnt] instead of array[i]. For cnt <
ARRAY_SIZE(array), this reads an uninitialized entry; for cnt ==
ARRAY_SIZE(array), it is an out-of-bounds read. Either case can lead to
an invalid socket pointer dereference and also leaks references taken
via sock_hold().
Fix the index to use i.
Fixes: 64b8bc7d5f ("net/rose: fix races in rose_kill_by_device()")
Co-developed-by: Fatma Alwasmi <falwasmi@purdue.edu>
Signed-off-by: Fatma Alwasmi <falwasmi@purdue.edu>
Signed-off-by: Pwnverse <stanksal@purdue.edu>
Link: https://patch.msgid.link/20251222212227.4116041-1-ritviktanksalkar@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A value of 0 for addr indicates that the IEB_LBCR register does not
need to be configured, as its default value is 0. However, the driver
will print an error log if addr is 0, so this issue needs to be fixed.
Fixes: 50bfd9c06f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251222022628.4016403-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the non-RT kernel, local_bh_disable() merely disables preemption,
whereas it maps to an actual spin lock in the RT kernel. Consequently,
when attempting to refill RX buffers via netdev_alloc_skb() in
macb_mac_link_up(), a deadlock scenario arises as follows:
WARNING: possible circular locking dependency detected
6.18.0-08691-g2061f18ad76e #39 Not tainted
------------------------------------------------------
kworker/0:0/8 is trying to acquire lock:
ffff00080369bbe0 (&bp->lock){+.+.}-{3:3}, at: macb_start_xmit+0x808/0xb7c
but task is already holding lock:
ffff000803698e58 (&queue->tx_ptr_lock){+...}-{3:3}, at: macb_start_xmit
+0x148/0xb7c
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&queue->tx_ptr_lock){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x148/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #2 (_xmit_ETHER#2){+...}-{3:3}:
rt_spin_lock+0x50/0x1f0
sch_direct_xmit+0x11c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #1 ((softirq_ctrl.lock)){+.+.}-{3:3}:
lock_release+0x250/0x348
__local_bh_enable_ip+0x7c/0x240
__netdev_alloc_skb+0x1b4/0x1d8
gem_rx_refill+0xdc/0x240
gem_init_rings+0xb4/0x108
macb_mac_link_up+0x9c/0x2b4
phylink_resolve+0x170/0x614
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
-> #0 (&bp->lock){+.+.}-{3:3}:
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
other info that might help us debug this:
Chain exists of:
&bp->lock --> _xmit_ETHER#2 --> &queue->tx_ptr_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&queue->tx_ptr_lock);
lock(_xmit_ETHER#2);
lock(&queue->tx_ptr_lock);
lock(&bp->lock);
*** DEADLOCK ***
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0xa0/0xf0
dump_stack+0x18/0x24
print_circular_bug+0x28c/0x370
check_noncircular+0x198/0x1ac
__lock_acquire+0x15a8/0x2084
lock_acquire+0x1cc/0x350
rt_spin_lock+0x50/0x1f0
macb_start_xmit+0x808/0xb7c
dev_hard_start_xmit+0x94/0x284
sch_direct_xmit+0x8c/0x37c
__dev_queue_xmit+0x708/0x1120
neigh_resolve_output+0x148/0x28c
ip6_finish_output2+0x2c0/0xb2c
__ip6_finish_output+0x114/0x308
ip6_output+0xc4/0x4a4
mld_sendpack+0x220/0x68c
mld_ifc_work+0x2a8/0x4f4
process_one_work+0x20c/0x5f8
worker_thread+0x1b0/0x35c
kthread+0x144/0x200
ret_from_fork+0x10/0x20
Notably, invoking the mog_init_rings() callback upon link establishment
is unnecessary. Instead, we can exclusively call mog_init_rings() within
the ndo_open() callback. This adjustment resolves the deadlock issue.
Furthermore, since MACB_CAPS_MACB_IS_EMAC cases do not use mog_init_rings()
when opening the network interface via at91ether_open(), moving
mog_init_rings() to macb_open() also eliminates the MACB_CAPS_MACB_IS_EMAC
check.
Fixes: 633e98a711 ("net: macb: use resolved link config in mac_link_up()")
Cc: stable@vger.kernel.org
Suggested-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://patch.msgid.link/20251222015624.1994551-1-xiaolei.wang@windriver.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ifconfig is a legacy tool and no longer installed by default on many
modern distributions. Update the documentation to reference ip from
iproute2 instead.
No functional change.
Signed-off-by: Jaime Saguillo Revilla <jaime.saguillo@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The test checks that with multi nexthops route the preferred route is the
one which matches source ip. In case when source ip is on dummy
interface, it checks that the routes are balanced.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251221192639.3911901-2-vadim.fedorenko@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Preference of nexthop with source address broke ECMP for packets with
source addresses which are not in the broadcast domain, but rather added
to loopback/dummy interfaces. Original behaviour was to balance over
nexthops while now it uses the latest nexthop from the group. To fix the
issue introduce next hop scoring system where next hops with source
address equal to requested will always have higher priority.
For the case with 198.51.100.1/32 assigned to dummy0 and routed using
192.0.2.0/24 and 203.0.113.0/24 networks:
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether d6:54:8a:ff:78:f5 brd ff:ff:ff:ff:ff:ff
inet 198.51.100.1/32 scope global dummy0
valid_lft forever preferred_lft forever
7: veth1@if6: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 06:ed:98:87:6d:8a brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet 192.0.2.2/24 scope global veth1
valid_lft forever preferred_lft forever
inet6 fe80::4ed:98ff:fe87:6d8a/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
9: veth3@if8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether ae:75:23:38:a0:d2 brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet 203.0.113.2/24 scope global veth3
valid_lft forever preferred_lft forever
inet6 fe80::ac75:23ff:fe38:a0d2/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
~ ip ro list:
default
nexthop via 192.0.2.1 dev veth1 weight 1
nexthop via 203.0.113.1 dev veth3 weight 1
192.0.2.0/24 dev veth1 proto kernel scope link src 192.0.2.2
203.0.113.0/24 dev veth3 proto kernel scope link src 203.0.113.2
before:
for i in {1..255} ; do ip ro get 10.0.0.$i; done | grep veth | awk ' {print $(NF-2)}' | sort | uniq -c:
255 veth3
after:
for i in {1..255} ; do ip ro get 10.0.0.$i; done | grep veth | awk ' {print $(NF-2)}' | sort | uniq -c:
122 veth1
133 veth3
Fixes: 32607a332c ("ipv4: prefer multipath nexthop that matches source address")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20251221192639.3911901-1-vadim.fedorenko@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a nexthop object is deleted, it is marked as dead and then
fib_table_flush() is called to flush all the routes that are using the
dead nexthop.
The current logic in fib_table_flush() is to only flush error routes
(e.g., blackhole) when it is called as part of network namespace
dismantle (i.e., with flush_all=true). Therefore, error routes are not
flushed when their nexthop object is deleted:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip route add 198.51.100.1/32 nhid 1
# ip route add blackhole 198.51.100.2/32 nhid 1
# ip nexthop del id 1
# ip route show
blackhole 198.51.100.2 nhid 1 dev dummy1
As such, they keep holding a reference on the nexthop object which in
turn holds a reference on the nexthop device, resulting in a reference
count leak:
# ip link del dev dummy1
[ 70.516258] unregister_netdevice: waiting for dummy1 to become free. Usage count = 2
Fix by flushing error routes when their nexthop is marked as dead.
IPv6 does not suffer from this problem.
Fixes: 493ced1ac4 ("ipv4: Allow routes to use nexthop objects")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Closes: https://lore.kernel.org/netdev/d943f806-4da6-4970-ac28-b9373b0e63ac@I-love.SAKURA.ne.jp/
Reported-by: syzbot+881d65229ca4f9ae8c84@syzkaller.appspotmail.com
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20251221144829.197694-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This fixes the device failing to initialize with "error reading MAC
address" for me, probably because the incorrect write of NCR_RST to
SR_NCR is not actually resetting the device.
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20251221082400.50688-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ace2x driver can optionally use the HDA infrastructure, but can still
build without that. However, with SND_HDA_CORE=m and SND_HDA_ALIGNED_MMIO=y,
it fails to link as built-in:
aarch64-linux-ld: drivers/soundwire/intel_ace2x.o: in function `intel_shim_wake':
intel_ace2x.c:(.text+0x2518): undefined reference to `snd_hdac_aligned_read'
aarch64-linux-ld: intel_ace2x.c:(.text+0x25d4): undefined reference to `snd_hdac_aligned_read'
aarch64-linux-ld: intel_ace2x.c:(.text+0x268c): undefined reference to `snd_hdac_aligned_write'
Add a Kconfig dependency that forces the soundwire driver to be a loadable
module if necessary.
Fixes: 79e7123c07 ("soundwire: intel_ace2x: fix wakeup handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20251223215014.534756-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rxe_odp_map_range_and_lock() must release umem_odp->umem_mutex when an
error occurs, including cases where rxe_check_pagefault() fails.
Fixes: 2fae67ab63 ("RDMA/rxe: Add support for Send/Recv/Write/Read with ODP")
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Link: https://patch.msgid.link/20251226094112.3042583-1-lizhijian@fujitsu.com
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
imx8qxp_pixel_link_find_next_bridge() already emits a DRM_DEV_ERROR() on
error except for -EPROBE_DEFER. The caller emits another one, which is
redundant. Remove the message in the caller and keep the one in
imx8qxp_pixel_link_find_next_bridge() as it is more informative about the
error cause.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-20-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use the destroy hook to put the reference on deallocation.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-17-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-16-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
In preparation for using bridge->next_bridge, we need to ensure that it
will never contain anything but NULL or a valid bridge pointer. Current
code stores an ERR_PTR when imx8qxp_pxl2dpi_find_next_bridge() errors
out. Instead of fixing that after the facts in the caller, change the
function to internally set the next_pointer and just return an int error
value.
No functional changes.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-15-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
imx8qxp_pxl2dpi_find_next_bridge() already emits a DRM_DEV_ERROR() for
every error except -EPROBE_DEFER. The caller emits another one, which is
redundant. Remove the message in the caller and keep the two in
imx8qxp_pxl2dpi_find_next_bridge() as they are more informative about the
error cause.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-14-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-12-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-11-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-10-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-9-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-8-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
This driver obtains a bridge pointer from of_drm_find_bridge() in the probe
function and stores it until driver removal. of_drm_find_bridge() is
deprecated. Move to of_drm_find_and_get_bridge() for the bridge to be
refcounted and use bridge->next_bridge to put the reference on
deallocation.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-7-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Many bridge drivers store a next_bridge pointer in their private data and
use it for attach and sometimes other purposes. This is going to be risky
when bridge hot-unplug is used.
Considering this example scenario:
1. pipeline: encoder --> bridge A --> bridge B --> bridge C
2. encoder takes a reference to bridge B
3. bridge B takes a next_bridge reference to bridge C
4. encoder calls (bridge B)->b_foo(), which in turns references
next_bridge, e.g.:
b_foo() {
bar(b->next_bridge);
}
If bridges B and C are removed, bridge C can be freed but B is still
allocated because the encoder holds a reference to B. So when step 4
happens, 'b->next-bridge' would be a use-after-free.
Calling drm_bridge_put() in the B bridge .remove function does not solve
the problem as it leaves a (potentially long) risk window between B removal
and the final deallocation of B. A safe moment to put the B reference is in
__drm_bridge_free(), when the last reference has been put. This can be done
by drivers in the .destroy func. However to avoid the need for so many
drivers to implement a .destroy func, just offer a next_bridge pointer to
all bridges that is automatically put it in __drm_bridge_free(), exactly
when the .destroy func is called.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/all/20251201-thick-jasmine-oarfish-1eceb0@houat/
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20251216-drm-bridge-alloc-getput-drm_of_find_bridge-v3-6-b5165fab8058@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
