The SMARC module can be used on the Kontron SMARC 2.2 Evaluation carrier
(ads2). Add an overlay to enable all the devices found on the carrier
and enable the corresponding peripherals of the SoC.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20251017135116.548236-4-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add device tree support for the Kontron SMARC-sAM67 module, which is
based on a TI AM67A SoC.
The module features:
* Quad-core AM67A94 at 1.4GHz with 8 GiB RAM
* 64 GiB eMMC, 4 MiB SPI flash for failsafe booting
* Dedicated RTC
* Multiple interfaces: 4x UART, 2x USB 2.0/USB 3.2, 2x GBE, QSPI,
7x I2C,
* Display support: 2x LVDS, 1x DSI (*), 1x DP (*)
* Camera support: 4x CSI (*)
* Onboard microcontroller for boot control, failsafe booting and
external watchdog
(*) not yet supported by the kernel
There is a base device tree and overlays which will add optional
features. At the moment there is one full featured variant of that
board whose device tree is generated during build by merging all the
device tree overlays.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://patch.msgid.link/20251017135116.548236-3-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add devicetree bindings for the AM67 based Kontron SMARC-sAM67
module.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251017135116.548236-2-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
At the moment the clock parent of the audio extclk output is PLL1_HSDIV6
of the main domain. This very clock output is also used among various IP
cores, for example for the USB1 LPM clock. The audio extclock being an
external clock output with a variable frequency, it is likely that a
user of this clock will try to set it's frequency to a different value,
i.e. an audio codec. Because that clock output is used also for other IP
cores, bad things will happen.
Instead of using PLL1_HSDIV6 use the PLL2_HSDIV8 as a sane default, as
this output is exclusively used among other audio peripherals.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20251017102228.530517-2-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Compute the values for second scaler for sharpness.
Fill the register bits corresponding to the scaler.
v1: Rename the title of patch [Ankit]
v2: Remove setup_casf from here[Ankit]
v3: Add skl_scaler_setup_casf in casf_enable
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251028120747.3027332-7-ankit.k.nautiyal@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The parent of the audio_refclk0/1 is about to change to a sane default
value. Thus, move the (soon to be) non-default value into the board
device tree.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20251017102228.530517-1-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The sharpness property requires the use of one of the scaler
so need to set the sharpness scaler coefficient values.
These values are based on experiments and vary for different
tap value/win size. These values are normalized by taking the
sum of all values and then dividing each value with a sum.
Add helper to compute and set the scaler coefficients.
v2: Fix ifndef header naming issue reported by kernel test robot
v3: Rename file name[Arun]
Replace array size number with macro[Arun]
v4: Correct the register format[Jani]
Add brief comment and expalin about file[Jani]
Remove coefficient value from crtc_state[Jani]
v5: Fix build issue
v6: Add new function for writing coefficients[Ankit]
v7: Add cooments and add a scaler id check [Ankit]
v8: Remove casf_enable from here[Ankit]
v9: Removed REG and use shift operator[Jani]
v10: Remove filter macros
v11: Add casf_write_coeff function to casf_enable
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251028120747.3027332-6-ankit.k.nautiyal@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add the register bits related to filter lut values
and helper to load the casf filter lut.
These values are golden values and these value has
to be loaded one time while enabling the casf.
v2: update commit message[Ankit]
v3: Add intel_casf prefix to filter_load fn[Jani]
v4: Define the filter macros here
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251028120747.3027332-5-ankit.k.nautiyal@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add register definitions for sharpness strength and
filter window size used by CASF. Provide functions to
read and write these fields.
The sharpness strength value is determined by user input,
while the winsize is based on the resolution. The casf_enable
flag should be set if the platform supports sharpness adjustments
and the user API strength is not zero. Once sharpness is
enabled, update the strength bit of the register whenever
the user changes the strength value, as the enable bit and
winsize bit remain constant.
Introduce helper to enable, disable and update strength.
Add relavant strength and winsize in both enable and disable.
v2: Introduce get_config for casf[Ankit]
v3: Replace 0 with FILTER_STRENGTH_MASK[Ankit]
v4: After updating strength add win_sz register
v5: Replace u16 with u32 for total_pixel
v6: Add casf logging
v7: Add helper for enable and disable casf
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251028120747.3027332-4-ankit.k.nautiyal@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Introduce a new crtc property "SHARPNESS_STRENGTH" that allows
the user to set the intensity so as to get the sharpness effect.
The value of this property can be set from 0-255.
It is useful in scenario when the output is blurry and user
want to sharpen the pixels. User can increase/decrease the
sharpness level depending on the content displayed.
v2: Rename crtc property variable [Arun]
Add modeset detail in uapi doc[Uma]
v3: Fix build issue
v4: Modify the subject line[Ankit]
Signed-off-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Tested-by: Adarsh G M <Adarsh.g.m@intel.com>
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://invent.kde.org/plasma/kwin/-/merge_requests/7689
Link: https://patch.msgid.link/20251028120747.3027332-2-ankit.k.nautiyal@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use core_param() and __core_param_cb() instead of __setup() or
__setup_param() to improve syntax checking and error messages.
Replace get_option() with kstrtouint(), because:
* the latter accepts a pointer to const char,
* these parameters should not accept ranges,
* error value can be passed directly to parser.
There is one more change apart from the parsing of numeric parameters:
slab_strict_numa parameter name must match exactly. Before this patch the
kernel would silently accept any option that starts with the name as an
undocumented alias.
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Link: https://patch.msgid.link/6ae7e0ddc72b7619203c07dd5103a598e12f713b.1761324765.git.ptesarik@suse.com
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Fix section mismatch warning reported by modpost:
.text:early_parse_cmdline() -> .init.data:boot_command_line
The function early_parse_cmdline() is only called during init and accesses
init data, so mark it __init to match its usage.
[ bp: This happens only when the toolchain fails to inline the function and
I haven't been able to reproduce it with any toolchain I'm using. Patch is
obviously correct regardless. ]
Signed-off-by: Yu Peng <pengyu@kylinos.cn>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/all/20251030123757.1410904-1-pengyu@kylinos.cn
All microcode patches up to the proper BIOS Entrysign fix are loaded
only after the sha256 signature carried in the driver has been verified.
Microcode patches after the Entrysign fix has been applied, do not need
that signature verification anymore.
In order to not abandon machines which haven't received the BIOS update
yet, add the capability to select which microcode patch to load.
The corresponding microcode container supplied through firmware-linux
has been modified to carry two patches per CPU type
(family/model/stepping) so that the proper one gets selected.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Waiman Long <longman@redhat.com>
Link: https://patch.msgid.link/20251027133818.4363-1-bp@kernel.org
Userspace needs access to the signal that caused the coredump before the
coredumping process has been reaped. Expose it as part of the coredump
information in struct pidfd_info. After the process has been reaped that
info is also available as part of PIDFD_INFO_EXIT's exit_code field.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-8-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
This is not needed anymore now that we have the new scheme to guarantee
all-or-nothing information exposure.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-7-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
There will likely be more info that we need to store in struct
pidfs_attr. We need to make sure that some of the information such as
exit info or coredump info that consists of multiple bits is either
available completely or not at all, but never partially. Currently we
use a pointer that we assign to. That doesn't scale. We can't waste a
pointer for each mulit-part information struct we want to expose. Use a
bitmask instead.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-6-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Some of the future fields in struct pidfd_info can be optional. If the
kernel has nothing to emit in that field, then it doesn't set the flag
in the reply. This presents a problem: There is currently no way to know
what mask flags the kernel supports since one can't always count on them
being in the reply.
Add a new PIDFD_INFO_SUPPORTED_MASK flag and field that the kernel can
set in the reply. Userspace can use this to determine if the fields it
requires from the kernel are supported. This also gives us a way to
deprecate fields in the future, if that should become necessary.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-5-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Validate that the size of struct pidfd_info is correctly updated.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-4-ca449b7b7aa0@kernel.org
Fixes: 1d8db6fd69 ("pidfs, coredump: add PIDFD_INFO_COREDUMP")
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
When PIDFD_INFO_COREDUMP is requested we raise it unconditionally in the
returned mask even if no coredump actually did take place. This was
done because we assumed that the later check whether ->coredump_mask as
non-zero detects that it is zero and then retrieves the dumpability
settings from the task's mm. This has issues though becuase there are
tasks that might not have any mm. Also it's just not very cleanly
implemented. Fix this.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-2-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Append a newline to the sysfs_emit() output in tle62x0_gpio_show. This
aligns with common kernel conventions and improves readability for
userspace tools that expect newline-terminated values.
Signed-off-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Link: https://patch.msgid.link/20251030124755.1828434-1-zhongqiu.han@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We started seeing "[drm] *ERROR* Timed out waiting PSR idle state" after
taking optimized guardband into use. These are seen because VSC SDPs are
sent on same line as AS SDPs when AS SDP is enabled. AS SDP is sent on line
configured in EMP_AS_SDP_TL register. We are configuring
crtc_state->vrr.vsync_start into that register.
Fix this by ensuring AS SDP is sent on line which is within
guardband. From the bspec:
EMP_AS_SDP_TL < SCL + Guardband
v2: check HAS_AS_SDP
Bspec: 71197
Fixes: 52ecd48b8d ("drm/i915/dp: Add helper to get min sdp guardband")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20251023043140.961104-1-jouni.hogander@intel.com
Replace direct printk() calls with the appropriate dev_*() logging
APIs.Use dev_err, dev_warn, dev_info, or dev_dbg to reflect the correct
severity level. Pass the canonical struct device pointer so logs
include device context and become traceable to specific hardware
instances.Improve log clarity, make messages filterable by device
and align the driver with kernel logging conventions to aid
debugging and maintenance.
Signed-off-by: HariKrishna Sagala <hariconscious@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20251025043011.598300-1-hariconscious@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For those amp with "AMP" name_prefix in the codec_info_list[], use the
AMP<index> format to meet the UCM expectation.
Fixes: 5cd5f8fc29 ("ASoC: SOF: Intel: add hyphen between name and index to amp name_prefix")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20251030065503.1216419-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if a -ENOMEM from smc_wr_alloc_link_mem() is handled by
giving up and going the way of a TCP fallback. This was reasonable
before the sizes of the allocations there were compile time constants
and reasonably small. But now those are actually configurable.
So instead of giving up, keep retrying with half of the requested size
unless we dip below the old static sizes -- then give up! In terms of
numbers that means we give up when it is certain that we at best would
end up allocating less than 16 send WR buffers or less than 48 recv WR
buffers. This is to avoid regressions due to having fewer buffers
compared the static values of the past.
Please note that SMC-R is supposed to be an optimisation over TCP, and
falling back to TCP is superior to establishing an SMC connection that
is going to perform worse. If the memory allocation fails (and we
propagate -ENOMEM), we fall back to TCP.
Preserve (modulo truncation) the ratio of send/recv WR buffer counts.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Reviewed-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Tested-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Link: https://patch.msgid.link/20251027224856.2970019-3-pasic@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Think SMC_WR_BUF_CNT_SEND := SMC_WR_BUF_CNT used in send context and
SMC_WR_BUF_CNT_RECV := 3 * SMC_WR_BUF_CNT used in recv context. Those
get replaced with lgr->max_send_wr and lgr->max_recv_wr respective.
Please note that although with the default sysctl values
qp_attr.cap.max_send_wr == qp_attr.cap.max_recv_wr is maintained but
can not be assumed to be generally true any more. I see no downside to
that, but my confidence level is rather modest.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Tested-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Link: https://patch.msgid.link/20251027224856.2970019-2-pasic@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Describe the "type" struct member using '@type' and move it together
with the rest of the doc for ctl_table_header to avoid a kernel-doc
warning:
Warning: include/linux/sysctl.h:178 Incorrect use of kernel-doc format:
* enum type - Enumeration to differentiate between ctl target types
Fixes: 2f2665c13a ("sysctl: replace child with an enumeration")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Joel Granados <joel.granados@kernel.org>
A bigger batch of fixes than I'd like, things built up due to holidays
and some last minute issues which caused me to hold off on sending a pul
request. None of these are super remarkable, and there's a few new
device IDs in here too including a relatively big block of AMD devices.
The Cirrus Logic CS530x support subject line is actually a fix that was
on the start of that series and got pulled in here, I forgot to fix the
subject up when merging.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmkDTOIACgkQJNaLcl1U
h9BPvwf/Ucl+RZswaJr2UFTc75FANPN1z8/zTqn1h7MdD3nYBx5O2TUgv8kin/lm
LL3eKiuXXkdZrIICcKOCvXI6cotLmd7CTt2kfPy12hGInNWkryOtqnpGDaQOSE8t
knqrdDuenuRULVSjQgsF7CrgchQ0Z52G2luIDTU2k9NZcqHLUhPVfVp0RGZxsTpW
kD73hWZdBqtIElxuq+xdsf5EGuZBR+OmEE3l7fIe/koaZjD/qjCABZybEhFbi+9I
yY0D2ECRV7ndHliR2sRPLpfUgylhggkLqtfba6Hf0RNJowsx9hP2Bsh/XdcN+r1B
EduDjDIt5HecelqRtjD46nuXAsjQrQ==
=aqRw
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.18-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.18
A bigger batch of fixes than I'd like, things built up due to holidays
and some last minute issues which caused me to hold off on sending a pul
request. None of these are super remarkable, and there's a few new
device IDs in here too including a relatively big block of AMD devices.
The Cirrus Logic CS530x support subject line is actually a fix that was
on the start of that series and got pulled in here, I forgot to fix the
subject up when merging.
In the comment for nf_conntrack_l4proto.h, the word "nfnetink" was
incorrectly spelled. It has been corrected to "nfnetlink".
Fixes a typo to enhance readability and ensure consistency.
Signed-off-by: caivive (Weibiao Tu) <cavivie@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Undocumented historical artifact inherited from ip_conntrack.
If value is 0, then no limit is applied at all, conntrack table
can grow to huge value, only limited by size of conntrack hashes and
the kernel-internal upper limit on the hash chain lengths.
This feature makes no sense; users can just set
conntrack_max=2147483647 (INT_MAX).
Disallow a 0 value. This will make it slightly easier to allow
per-netns constraints for this value in a future patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Use C99 struct initializer for nft_set_iter, simplifying the code and
preventing future errors due to uninitialized fields if new fields are
added to the struct.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
The .min_sel and .max_sel fields remained uninitialized in the new
linear_range, causing an error further down the line. Copy the old
values of these fields to the new one as they represent the range of
register values, which does not change.
Fixes: d2ad981151 ("regulator: bd718x7: Support external connection to scale voltages")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20251030-mini_iv-v3-2-ef56c4d9f219@gocontroll.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function SND_SOC_DAPM_AIF_OUT has its third parameter
as stream index. The stream index is numbered from 0 to 3 for
every output interface widget but with same stream name
"HiFi Capture". So, if the stream name is same, the stream
index cannot be different. Also for capture, there is only one
stream "HiFi Capture", so only one stream index. Therefore,
with this patch changed the stream index to 0 for all the output
interface widgets with stream name "HiFi Capture".
Signed-off-by: Sharique Mohammad <sharq0406@gmail.com>
Link: https://patch.msgid.link/20251029164134.4123618-1-sharq0406@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
printk() tries to flush messages with NBCON_PRIO_EMERGENCY on
nbcon consoles immediately. It might take seconds to flush all
pending lines on slow serial consoles. Note that there might be
hundreds of messages, for example:
[ 3.771531][ T1] pci 0000:3e:08.1: [8086:324
** replaying previous printk message **
[ 3.771531][ T1] pci 0000:3e:08.1: [8086:3246] type 00 class 0x088000 PCIe Root Complex Integrated Endpoint
[ ... more than 2000 lines, about 200kB messages ... ]
[ 3.837752][ T1] pci 0000:20:01.0: Adding to iommu group 18
[ 3.837851][ T
** replaying previous printk message **
[ 3.837851][ T1] pci 0000:20:03.0: Adding to iommu group 19
[ 3.837946][ T1] pci 0000:20:05.0: Adding to iommu group 20
[ ... more than 500 messages for iommu groups 21-590 ...]
[ 3.912932][ T1] pci 0000:f6:00.1: Adding to iommu group 591
[ 3.913070][ T1] pci 0000:f6:00.2: Adding to iommu group 592
[ 3.913243][ T1] DMAR: Intel(R) Virtualization Technology for Directed I/O
[ 3.913245][ T1] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 3.913245][ T1] software IO TLB: mapped [mem 0x000000004f000000-0x0000000053000000] (64MB)
[ 3.913324][ T1] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 655360 ms ovfl timer
[ 3.913325][ T1] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 3.913326][ T1] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 3.913327][ T1] RAPL PMU: hw unit of domain psys 2^-0 Joules
[ 3.933486][ T1] ------------[ cut here ]------------
[ 3.933488][ T1] WARNING: CPU: 2 PID: 1 at arch/x86/events/intel/uncore.c:1156 uncore_pci_pmu_register+0x15e/0x180
[ 3.930291][ C0] watchdog: Watchdog detected hard LOCKUP on cpu 0
[ 3.930291][ C0] Kernel panic - not syncing: Hard LOCKUP
[...]
[ 3.930291][ C0] CPU: 0 UID: 0 PID: 18 Comm: pr/ttyS0 Not tainted...
[...]
[ 3.930291][ C0] RIP: 0010:nbcon_reacquire_nobuf+0x11/0x50
[ 3.930291][ C0] Call Trace:
[...]
[ 3.930291][ C0] <TASK>
[ 3.930291][ C0] serial8250_console_write+0x16d/0x5c0
[ 3.930291][ C0] nbcon_emit_next_record+0x22c/0x250
[ 3.930291][ C0] nbcon_emit_one+0x93/0xe0
[ 3.930291][ C0] nbcon_kthread_func+0x13c/0x1c0
The are visible two takeovers of the console ownership:
- The 1st one is triggered by the "WARNING: CPU: 2 PID: 1 at
arch/x86/..." line printed with NBCON_PRIO_EMERGENCY.
- The 2nd one is triggered by the "Kernel panic - not syncing:
Hard LOCKUP" line printed with NBCON_PRIO_PANIC.
There are more than 2500 lines, at about 240kB, emitted between
the takeover and the 1st "WARNING" line in the emergency context.
This amount of pending messages had to be flushed by
nbcon_atomic_flush_pending() when WARN() printed its first line.
The atomic flush was holding the nbcon console context for too long so
that it triggered hard lockup on the CPU running the printk kthread
"pr/ttyS0". The kthread needed to reacquire the console ownership
for restoring the original serial port state in serial8250_console_write().
Prevent the hardlockup by releasing the nbcon console ownership after
each emitted record.
Note that __nbcon_atomic_flush_pending_con() used to hold the console
ownership all the time because it blocked the printk kthread. Otherwise
the kthread tried to flush the messages in parallel which caused repeated
takeovers and more replayed messages.
It is not longer a problem because the repeated takeovers are blocked
by the counter of emergency contexts, see nbcon_cpu_emergency_cnt.
Link: https://lore.kernel.org/all/aNQO-zl3k1l4ENfy@pathway.suse.cz
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20250926124912.243464-4-pmladek@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
The printk kthread might be running when there is a panic in progress.
But it is not able to acquire the console ownership any longer.
Prevent the desperate attempts to acquire the ownership and allow sleeping
in panic. It would make it behave the same as when there is any CPU
in an emergency context.
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20250926124912.243464-3-pmladek@suse.com
[pmladek@suse.com: Rebased on top of 6.18-rc1 (panic_in_progress() moved to panic.c)]
Signed-off-by: Petr Mladek <pmladek@suse.com>
In emergency contexts, printk() tries to flush messages directly even
on nbcon consoles. And it is allowed to takeover the console ownership
and interrupt the printk kthread in the middle of a message.
Only one takeover and one repeated message should be enough in most
situations. The first emergency message flushes the backlog and printk
kthreads get to sleep. Next emergency messages are flushed directly
and printk() does not wake up the kthreads.
However, the one takeover is not guaranteed. Any printk() in normal
context on another CPU could wake up the kthreads. Or a new emergency
message might be added before the kthreads get to sleep. Note that
the interrupted .write_thread() callbacks usually have to call
nbcon_reacquire_nobuf() and restore the original device setting
before checking for pending messages.
The risk of the repeated takeovers will be even bigger because
__nbcon_atomic_flush_pending_con is going to release the console
ownership after each emitted record. It will be needed to prevent
hardlockup reports on other CPUs which are busy waiting for
the context ownership, for example, by nbcon_reacquire_nobuf() or
__uart_port_nbcon_acquire().
The repeated takeovers break the output, for example:
[ 5042.650211][ T2220] Call Trace:
[ 5042.6511
** replaying previous printk message **
[ 5042.651192][ T2220] <TASK>
[ 5042.652160][ T2220] kunit_run_
** replaying previous printk message **
[ 5042.652160][ T2220] kunit_run_tests+0x72/0x90
[ 5042.653340][ T22
** replaying previous printk message **
[ 5042.653340][ T2220] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5042.654628][ T2220] ? stack_trace_save+0x4d/0x70
[ 5042.6553
** replaying previous printk message **
[ 5042.655394][ T2220] ? srso_alias_return_thunk+0x5/0xfbef5
[ 5042.656713][ T2220] ? save_trace+0x5b/0x180
A more robust solution is to block the printk kthread entirely whenever
*any* CPU enters an emergency context. This ensures that critical messages
can be flushed without contention from the normal, non-atomic printing
path.
Link: https://lore.kernel.org/all/aNQO-zl3k1l4ENfy@pathway.suse.cz
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20250926124912.243464-2-pmladek@suse.com
[pmladek@suse.com: Added changes proposed by John Ogness]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Titas reports that the accelerometer sensor on their laptop only
works after a warm boot or unloading/reloading the amd-sfh kernel
module.
Presumably the sensor is in a bad state on cold boot and failing to
start, so explicitly stop it before starting.
Cc: stable@vger.kernel.org
Fixes: 93ce5e0231 ("HID: amd_sfh: Implement SFH1.1 functionality")
Reported-by: Titas <novatitas366@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220670
Tested-by: Titas <novatitas366@gmail.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
SONiX AK870 PRO keyboard pretends to be an apple keyboard by VID:PID,
rendering function keys not treated properly. Despite being a
SONiX USB DEVICE, it uses a different name, so adding it to the list.
Signed-off-by: April Grimoire <april@aprilg.moe>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add a check to ensure locally generated packets (skb->sk != NULL) do
not use direct output in tunnel mode, as these packets require proper
L2 header setup that is handled by the normal XFRM processing path.
Fixes: 5eddd76ec2 ("xfrm: fix tunnel mode TX datapath in packet offload mode")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The GSO segmentation functions for ESP tunnel mode
(xfrm4_tunnel_gso_segment and xfrm6_tunnel_gso_segment) were
determining the inner packet's L2 protocol type by checking the static
x->inner_mode.family field from the xfrm state.
This is unreliable. In tunnel mode, the state's actual inner family
could be defined by x->inner_mode.family or by
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed, causing GSO to create
segments with the wrong L2 header type.
This patch fixes the bug by deriving the inner mode directly from the
packet's inner protocol stored in XFRM_MODE_SKB_CB(skb)->protocol.
Instead of replicating the code, this patch modifies the
xfrm_ip2inner_mode helper function. It now correctly returns
&x->inner_mode if the selector family (x->sel.family) is already
specified, thereby handling both specific and AF_UNSPEC cases
appropriately.
With this change, ESP GSO can use xfrm_ip2inner_mode to get the
correct inner mode. It doesn't affect existing callers, as the updated
logic now mirrors the checks they were already performing externally.
Fixes: 26dbd66eab ("esp: choose the correct inner protocol for GSO on inter address family tunnels")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In the output path, xfrm_dev_offload_ok and xfrm_get_inner_ipproto
need to determine the protocol family of the inner packet (skb) before
it gets encapsulated.
In xfrm_dev_offload_ok, the code checked x->inner_mode.family. This is
unreliable because, for states handling both IPv4 and IPv6, the
relevant inner family could be either x->inner_mode.family or
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed.
In xfrm_get_inner_ipproto, the code checked x->outer_mode.family. This
is also incorrect for tunnel mode, as the inner packet's family can be
different from the outer header's family.
At both of these call sites, the skb variable holds the original inner
packet. The most direct and reliable source of truth for its protocol
family is its destination entry. This patch fixes the issue by using
skb_dst(skb)->ops->family to ensure protocol-specific headers are only
accessed for the correct packet type.
Fixes: 91d8a53db2 ("xfrm: fix offloading of cross-family tunnels")
Fixes: 45a98ef492 ("net/xfrm: IPsec tunnel mode fix inner_ipproto setting in sec_path")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The keyboard of this device has the following in its report description
for Usage (Keyboard) in Collection (Application):
# 0x15, 0x00, // Logical Minimum (0) 52
# 0x25, 0x65, // Logical Maximum (101) 54
# 0x05, 0x07, // Usage Page (Keyboard) 56
# 0x19, 0x00, // Usage Minimum (0) 58
# 0x29, 0xdd, // Usage Maximum (221) 60
# 0x81, 0x00, // Input (Data,Arr,Abs) 62
Since the Usage Min/Max range exceeds the Logical Min/Max range,
keypresses outside the Logical range are not recognized. This includes,
for example, the Japanese language keyboard variant's keys for |, _ and
\.
Fixup the report description to make the Logical range match the Usage
range, fixing the interpretation of keypresses above 101 on this device.
Signed-off-by: Lauri Tirkkonen <lauri@hacktheplanet.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The E-core in Panther Lake is Darkmont, not Crestmont.
Nova Lake is built from Coyote Cove (P-core) and Arctic Wolf (E-core).
Fixes: 43bb700cff ("x86/cpu: Update Intel Family comments")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://patch.msgid.link/20251028172948.6721-1-tony.luck@intel.com
